Dahua IPC-PFW8802-A180 User manual

Dahua HD IR Panoramic Bullet Network Camera
Quick Start Guide
Version 1.0.1
Dahua Vision Technology Co., LTD

i
Welcome
Thank you for purchasing our Network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
Please check if the power supply is correct before operating the device.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
Limited power source is rated AC 24V in the IEC60950-1. (Power supply requirement is subject to
the device label).
Please install easy-to-use device for power off before installing wiring, which is for emergent power
off when necessary.
Please prevent the line cord from being trampled or pressed, especially the plug, power socket and
the junction from the device.
Note: Do not connect these two power supplying sources to the device at the same time; it
may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Environment
Please don’t aim the device at strong light (such as lighting, sunlight and so on) to focus; otherwise
it may cause overexposure (It is not the device malfunction), which will affect the longevity of CCD
or CMOS.
Please transport, use and store the device within the range of allowed humidity and temperature.
Please don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold and
with strong electromagnetic radiation or unstable lighting.
Please do not allow water and other liquid falling into the camera in case that the internal
components are damaged.
Please do not allow rain or damp to the indoor device in case fire or lightning may occur.
Please keep the sound ventilation in case of heat accumulation.
Please pack the device with standard factory packaging or material with same quality when
transporting the device.
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

ii
3. Operation and Daily Maintenance
Please do not touch the heat dissipation component of the device directly in order to avoid scald.
Please do not dismantle the device; there is no component which can be fixed by users themselves
in the machine. It may cause water leakage or bad image for the device due to unprofessional
dismantling. Please contact after-sale service to replace desiccant if it becomes green.
It is recommended to use the device with thunder proof device in order to improve thunder proof
effect.
The grounding holes of the product are recommended to be grounded to further enhance the
reliability of the camera.
Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the dust
or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away the dust gently if
it is necessary to clean.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean
the device. Don’t use volatile solvent like alcohol, benzene, thinner and etc or strong detergent with
abrasiveness, otherwise it will damage the surface coating or reduce the working performance of
the device.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods to deal with once dirt is found:
Stained with dirt
Use oil-free soft brush or hair dries to remove it gently.
Stained with grease or fingerprint
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or
paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to change
the cloth and wipe several times if it is not clean enough.
Warning
Please modify the default password after login in order to avoid being stolen.
Please use the standard accessories provided by manufacturer and make sure the device is
installed and fixed by professional engineers.
Please prevent the device surface from the radiation of laser beam when using laser beam device.
Please do not provide two or more power supply modes for the device, otherwise it may cause
damage to the device.
Statement
Please refer to the actual product for more details; the manual is just for reference.
The manual will be regularly upgraded according to the product update; the upgraded content will
be added in the manual without prior announcement.
Please contact the supplier or customer service if there is any problem occurred when using the
device.

iii
Please contact the customer service for the latest procedure and supplementary documentation.
There may be deviation between the actual value of some data and the value provided in the
manual due to the reasons such as the real environment is not stable and so on. Please refer to
the company’s final explanation if there is any doubt or dispute.
The company is not liable for any loss caused by the operation which is not followed by the manual.
FCC Information
1. FCC conditions：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference;
This device must accept any interference received, including interference that may cause
undesired operation.
2. FCC compliance：
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Note:
Please refer to the disk for more details, check and download corresponding user’s manual and tool.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1

iv
Table of Contents
1Device Structure .........................................................................................................................1
1.1 Device External Cable .................................................................................................1
1.2 Framework and Dimension.........................................................................................2
1.3 Alarm Setup...................................................................................................................2
2Device Installation ......................................................................................................................5
3Network Configuration...............................................................................................................9
3.1 Modify IP Address........................................................................................................9
3.2 Login WEB Interface..................................................................................................10

1
1Device Structure
1.1 Device External Cable
Note:
The following figure is for reference only, which is used to know the function of cable port.
You can refer to the following figure for cable information. See Figure 1-1.
Figure 1-1
Please refer to the following sheet for detailed information.
No.
Port
Name
Function
Connector
Note
1
AUDIO
OUT
Audio
output port
RCA
Output audio signal to speaker and etc.
2
AUDIO
IN
Audio input
port
RCA
Input audio signal, receive analog audio signal from
pickup and etc.
3
LAN
Network
port
Ethernet
port
Connect to standard Ethernet cable.
Note: Some series don’t support PoE.
4
I/O
I/O port
-
Alarm signal input/output. Please refer to sheet 1-2 for
more details.
5
Power
Power input
port
-
Power port. Input DC 12V or AC 24V power.
Note:
Please connect the DC5.5 round port to 2-pin
converter cable when you are using AC 24V
power.
Please use according to device tag.
Sheet 1-1
Please refer to sheet 1-2 for details about port function. .

2
Port Name
SN
Name
Note
I/O Port
1
ALARM_OUT
Alarm output port. It is to output the alarm signal to the
alarm device.
2
ALARM_OUT_GND
3
ALARM_IN1
Alarm input port 1. It is to receive the on-off signal from the
external alarm source.
4
ALARM_IN2
Alarm input port 2. It is to receive the on-off signal from the
external alarm source.
5
ALARM_IN_GND
Alarm input ground port
Sheet 1-2
1.2 Framework and Dimension
Note:
The following figure is for reference only, which is used to know the device dimension.
Please refer to the following figure for dimension information. The unit is mm. See Figure 1- 2.
Figure 1-2
1.3 Alarm Setup
Note:
It is only supported by some series products.

3
Figure 1-3
Alarm input, output connection description:
Step 1
Connect alarm input device to the alarm input of I/O port cable.
Step 2
Connect alarm output device to the ALARM_OUT and ALARM_OUT_GND of I/O port cable,
Alarm output is the relay switch output; alarm output port can only be connected to NO (normally
open) alarm device.
Step 3
Open the WEB, set alarm input and output correspondingly in alarm setup. Alarm input on the
WEB is corresponding to that of the device I/O port cable. When there is alarm, alarm input
device will generate signal of high and low level. Set corresponding NO and NC inputs.
Step 4
Set alarm output on the WEB, the alarm output is corresponding to the alarm output end of the
device, this is the alarm output port of the I/O port cable.
Please refer to the following figure for alarm input and output information. See Figure 1-4.
Alarm input: When the input signal is idle or grounded, the device can collect the different
statuses of the alarm input port. The input signal is connected to 3.3V or it is idle; the device
collects the logic “1”. When the input signal is grounded, the device collects the logic “0”.
Figure 1-4

4
Alarm output: port ALARM_OUT and ALM_OUT_GND form a switch, which is used to provide
alarm output. Normally the switch is on; it will be off when there is alarm output.
Figure 1-5

5
2Device Installation
Note:
Please make sure the installation surface can min support the 3X weight of the camera and
the bracket.
Please cut off the power before installing Micro SD card.
Figure 2-1
Step 1
SD card installation (Optional)
Note:
It needs to implement the step if there is a SD card slot in the device and it needs to use the SD
card.
You can see the SD installation card slot, analog video output port and reset button after you
open the lower cover.
Insert the SD card into the slot which is shown in Figure 2-2, you can press the SD card slightly
to insert it because the card slot is elastic.

6
Figure 2-2
Note:
You can connect the analog output port to the TV monitor to check image via analog output
cable.
Press the reset button for 4 to 5 seconds to realize reset function for the device.
Step 2
Stick the installation position map on the designated surface where you will install the device
(wall or ceiling), then dig holes according to hole location marked on installation map.
Step 3
Open the accessories bag, take out expansion bolts and insert them into the hole you just dug.
Step 4
Open the accessories bag, take out screws. Tighten the 4 screws to fix the device on the
installation surface (wall or ceiling). You can move the device sunshield back and forth. When
you have fixed the device, you must tighten screws on sunshade.
Step 5
Plug the external cables of the device properly according to the use requirements.
Step 6
Adjust the monitoring direction of the device.
Note:
Please be sure to loosen the adjusting screws when adjusting the device position and angle,
tighten the adjusting screws after adjustment.
The continuous rotation toward the same direction for the camera body has to be no more
than 3 circles.
The lower cover can’t be opened for a long time, besides; it can’t be opened in the humid
environment in case water mist and fog problem may happen to the device.

7
Figure 2-3
1. Use screwdriver to loosen adjusting screws.
2. Adjust the device in all possible directions, and set its monitoring direction according to use
requirement.
3. Use screwdriver to tighten the adjusting screws.
Step 7
Waterproof connector installation for network port; see Figure 2-4 for more details.
Note:
Please implement this step if the device is equipped with network port waterproof connector and
it is used outdoors.
Figure 2-4
1. Keep the convex groove outward and install the rubber ring into the network port, keep the
smaller hole of the rubber ring outward and install the fixing rubber ring into the main body of
the waterproof connector.
2. Pull the network cable without crystal head through main body of waterproof connector, fixing
rubber ring and waterproof locking cover, make the crystal head of network cable, and then
insert it into the network cable.
3. Put the main body of waterproof connector on the network port and rotate it clockwise to lock
the network port and waterproof connector firmly.

8
4. Put the waterproof locking cover on the main body of waterproof connector and rotate it
clockwise to lock the waterproof connector and waterproof locking cover firmly.

9
3 Network Configuration
The IP address of all the cameras is the same when leaving factory (default IP192.168.1.108), in
order to make the camera get access to the network smoothly, please plan the useable IP
segment reasonably according to the actual network environment.
3.1 Modify IP Address
IP address can be acquired and modified through quick configuration tool for the cameras which
are accessed via wired network, it needs to connect wired network to configure wireless
parameters before using wireless network cameras. In this chapter, it will introduce the approach
of modifying IP address via “Quick Configuration Tool”; also you can modify the IP address in the
network parameters of the WEB interface, please refer to the document in the disk << WEB
Operation Manual>> for more details.
Note:
Currently the quick configuration tool only supports the cameras which apply to the same
network segment with computer IP address.
Step 1 Double click the “ConfigTools.exe” and open the quick configuration tool.
Step 2 Double click the device to be configured, the system will pop out the “Login”dialog box.
Enter the IP address, user name, password and port number of the camera, and click
“Confirm”.
Note:
The default user name and password are admin and admin respectively, the default of port is
37777. See Figure 3-1 for more details.
Figure 3-1
Step 3 Modify the camera IP address on the “Net”interface, click “Save”to finish modification.

10
See Figure 3-2 for more details.
Figure 3-2
3.2 Login WEB Interface
Note:
Different devices may have different WEB interfaces, the figures below are just for reference,
please refer to the document <<WEB Operation Manual>> in the disk and the actual interface for
more details
Step 1 Open IE and input the modified camera IP address in the address bar.
Step 2 The login interface is shown below, please input your user name and password (Default
user name is admin and password is admin respectively), click “login”.
See Figure 3-3 for more details.

11
Figure 3-3
Step 3 Install controls according to the system prompt; see Figure 3-4 for the WEB main interface.
Please modify the administrator password as soon as possible after you successfully logged in.
Figure 3-4

12
Note:
This quick start guide is for reference only. Slight difference may be found in user
interface.
All the designs and software here are subject to change without prior written notice.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website or contact your local service engineer for more information.
Dahua Vision Technology Co., Ltd
Address：No.1199 Bin’an Road, Binjiang District, Hangzhou, PRC.
Postcode: 310053
Tel: [phone]
Fax: [phone]
Email:[e-mail]
Website: www.dahuasecurity.com