Dahua SD6C230U-HNI User manual

6-inch IR Intelligent Speed Dome Installation Manual
Version 1.1.5

i
Table of Contents
1INSTALLATION PREPARATION ...................................................................1
1.1 Basic Requirements.................................................................................................................1
1.2 Installation Check ....................................................................................................................1
1.3 Cable Preparation ....................................................................................................................1
1.3.1 Cable Lowest Specification Requirement..............................................................................1
1.3.2 Select Needed Power Supply Cable According to Transmission Distance...........................2
2SPEED DOME INSTALLATION .....................................................................3
2.1 Check Device............................................................................................................................3
2.2 Open Device .............................................................................................................................3
2.3 DIP Switch Setup......................................................................................................................3
2.3.1 DIP Switch Location...............................................................................................................3
2.3.2 DIP Switch Setup...................................................................................................................5
2.3.3 Address Setup .......................................................................................................................5
2.3.4 Baud Rate and Parity Setup..................................................................................................6
2.3.5 Terminal Matched Resistance Setup.....................................................................................7
2.4 Reset Button and Micro-SD Card Installation.......................................................................8
2.5 Speed Dome Installation .........................................................................................................9
2.5.1 Install Quick Mount Connector.............................................................................................10
2.5.2 Speed Dome Cable .............................................................................................................11
3WALL-MOUNTED BRACKET INSTALLATION...........................................13
3.1 Mounting Components and Dimension...............................................................................13
3.2 Wall-mounted Bracket Installation Steps ............................................................................14
3.2.1 Installation Conditions..........................................................................................................14
3.2.2 Installation Steps .................................................................................................................14
4HANG-MOUNT BRACKET INSTALLATION................................................15
4.1 Mounting Component and Dimension.................................................................................15
4.2 Hang-Mount Bracket Installation Steps...............................................................................16
4.2.1 Installation Conditions..........................................................................................................16

ii
4.2.2 Installation Steps .................................................................................................................16
5CORNER-MOUNTED BRACKET INSTALLATION......................................19
5.1 Mounting Component and Dimension.................................................................................19
5.2 Corner-mounted Bracket Installation Steps........................................................................19
5.2.1 Installation Conditions..........................................................................................................19
5.2.2 Installation Steps .................................................................................................................20
6POLE-MOUNTED BRACKET INSTALLATION............................................ 21
6.1 Mounting Components..........................................................................................................21
6.2 Pole-mounted Bracket Installation Steps............................................................................21
6.2.1 Installation Conditions..........................................................................................................21
6.2.2 Installation Steps .................................................................................................................22
7APPENDIX ⅠTHUNDER PROOF AND SURGE PROTECTION
(OUTDOORS)..........................................................................................................24
7.1 Lightning Protection (Indoors) .............................................................................................24
8APPENDIX ⅡABOUT RS485 BUS .............................................................26
8.1 RS485 Bus Main Feature.......................................................................................................26
8.2 RS485 Bus Transmission Distance......................................................................................26
8.3 The Problem in Practical Use ...............................................................................................26
8.4 RS485 Bus FAQ......................................................................................................................27
9APPENDIX ⅢTHE RELATIONSHIP BETWEEN AC 24V CABLE
DIAMETER AND TRANSMISSION DISTANCE......................................................28
10 APPENDIX ⅣTHE RELATIONSHIP BETWEEN DC 12V CABLE
DIAMETER AND TRANSMISSION DISTANCE......................................................29
11 APPENDIX ⅤWIRE GAUGE REFERENCE SHEET...................................31

iii
Welcome
Thank you for purchasing our speed dome!
Please read the following safeguards and warnings carefully before you install or use the
product!

iv
Important Safeguards and Warnings
Safety Measures
1. Qualified Engineer Needed
The installation engineer or maintenance engineer shall have corresponding CCTV system
installation certificate or maintenance qualification certificate.
The installation engineer or maintenance engineer shall have qualification certificate for work
at height.
The installation engineer or maintenance engineer shall have the basic knowledge and
operation technique for low-voltage cable layout and low-voltage electronic cable connection.
Please read the installation manual carefully and keep it well for future reference,
We are not liable for any problems caused by unauthorized modifications or attempted repair.
2. Lifting Appliance Requirement
Please select the proper speed dome installation mode and use the lifting appliances at the
safety environment.
The lifting appliances shall have the enough capacity to reach the installation height.
The lifting appliances shall have safe performance.
The precaution measures include two types: Warning and Note.
Warning: It is to alert you there is an optional risk of death or series injury!
Note: It is to alert you, there is an optional risk of damage or property loss!
Warning
1. All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
rated voltage conformed to Limited Power Source according to the IEC60950-1. (Power
supply requirement is subject to the device label).
2. We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
3. Be sure to use all the accessories (such as power adapter) recommended by manufacturer.
4. Do not connect several speed domes to one power adapter. It may result in overheat or fire
if it exceeds the rated load.

v
5. Before you connect the cable, install or uninstall, or begin the daily maintenance work,
please turn off the power and unplug the power cable.
6. Please make sure the produce is secure firmly on the wall or the ceiling.
7. Please turn off the power and unplug the power cable, If there is any smoke, disgusting
smell, or noise. Please contact your local retailer or customer service center for help.
8. All the examination and repair work should be done by the qualified service engineers. We
are not liable for any problems caused by unauthorized modifications or attempted repair.
Note
1. Safety Transportation
Heavy stress, violent vibration or water splash are not allowed during transportation, storage
and installation.
This series product must use split type package during the transportation.
We are not liable for any damage or problem resulting from the integrated package during
the transportation.
2. When device is malfunction
Shut down the device and disconnect the power cable immediately if there is smoke, abnormal
smell or abnormal function. Please contact your local retailer ASAP.
3. Do not try to dismantle or modify the device
There is risk of personal injury or device damage resulting from opening the shell.
Please contact your local retailer if there is internal setup or maintenance requirement.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
4. Do not allow other object falling into the device
Please make sure there is no metal or inflammable, explosive substance in the speed dome.
The above mentioned objects in the device may result in fire, short-circuit or damage.
Please shut down the device and disconnect the power cable if there is water or liquid falling
into the camera. Please contact your local retailer ASAP.
Please pay attention to the camera. Avoid the sea water or rain to erode the camera.
5. Handle carefully
Do not allow this series product fall down to the ground.
Avoid heavy vibration.
6. Installation Environment Requirement
This series speed dome should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
This series product shall be away from the strong electromagnetism radiant, please keep it
away from wireless power, TV transmitter, transformer and etc.

vi
7. Daily Maintenance
Please use the soft cloth to clean dust on the shell, or you can use soft cloth with cleaning
liquid to clean the shell and then use soft cloth to make it dry.
Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result
in shell transfiguration or paint flake.
Do not allow the plastic or rubber material to touch the shell for a long time. It may result in
paint flake.

1
1INSTALLATION PREPARATION
1.1 Basic Requirements
All installation and operation here should conform to your local electrical safety codes, fire
prevention laws and some related regulations.
Make sure if the application scene of the speed dome conforms to the installation
requirements. Please contact your dealer if you have any questions.
Please use the product according to the operating environment.
Please keep the original packing material well after opening the package; you can use
original packing material to pack the speed dome and send it back for maintenance in case
problems occur.
1.2 Installation Check
Make sure the installation site has enough space to hold the product and its mounting
components.
Please make sure the ceiling or wall can sustain 8X weight of the speed dome and its
mounting components.
Please make sure the wall is thick enough to install expansion bolts (Users need to purchase
separately).
It needs to guarantee the installation height shall be more than 6m if it is the intelligent
tracking speed dome or laser speed dome.
1.3 Cable Preparation
Please select video cable and lowest specification requirement of video coaxial cable according
to the transmission distance.
1.3.1 Cable Lowest Specification Requirement
75 ohm.
Full cable with copper conductor.
95% knitted copper shield.
Please refer to appendix Ⅱfor RS485.
International Model
Max Transmission Distance
(Ft\M)
RG59/U
750Ft/229M
RG6/U
1,000Ft/305M
RG11/U
1,500Ft/457M
Note
The above can be applied to analog speed dome and network speed dome.
International Model
Max Transmission Distance
(M\Ft)
SYV-75-3
720P(25fps\30fps)：500M/1640Ft
720P(50fps\60fps)：300M/984Ft
1080P(25fps\30fps): 300M/984Ft
Note

2
The above can be applied to HDCVI speed dome.
1.3.2 Select Needed Power Supply Cable According to Transmission Distance
Refer to appendix Ⅱfor AC 24V power supply device.
Refer to appendix Ⅲfor DC 12V power supply device.

3
2Speed Dome Installation
2.1 Check Device
First please check if the device is in a good condition in the packing box before installation, and
all the components are complete (refer to packing list for more details).
2.2 Open Device
Open the box, take out the device and remove adhesive tape covered on the dome body, which
is shown in Figure 2-1.
Figure 2-1
2.3 DIP Switch Setup
2.3.1 DIP Switch Location
The corresponding functions between analog speed dome and HDCVI speed dome are different,
which will be separately introduced below.
2.3.1.1 Analog Speed Dome
There are two DIP switches on the PCB board of the speed dome side (attached with DIP label),
which are used to set speed dome address, baud rate and parity. The location of DIP switch is
shown in Figure 2-2.

4
Figure 2-2
2.3.1.2 HDCVI Speed Dome
There are two DIP switches on the PCB board of the speed dome side (attached with DIP label),
which are used to set speed dome address and parity. The location of DIP switch is shown in
Figure 2-3.

5
Figure 2-3
2.3.2 DIP Switch Setup
It needs to set the address number and baud rate before controlling the speed dome.
Note
After some related information has been reset, it has to cut off the power and reboot the device
to make the new settings valid.
There are two DIP switches on the PCB board of the speed dome side, which are used to
confirm the speed dome address, baud rate and parity parameters.
For the protocol DIP switch, 1~3 is NC neutral bit, 4 is the setting bit for 120Ω matched
resistance, ON is to connect 120Ω matched resistance, 5, 6 are the setting bit for parity, 7, 8 are
the setting bit for baud rate. Among the DIP switch numbers, 1 is the lowest bit while 8 is the
highest bit.
Note
The intelligent speed dome can self-adapt to PELCO-D, PELCO-P and industrial standard
protocol, control protocol doesn’t need to be set via DIP switch.
2.3.3 Address Setup
The speed dome can use DIP switch to set address number, coding mode adopts binary coding.
1~8 bits are valid bit, the highest address bit is 255, the address label is shown in Figure 2-4,
please refer to Table 2-1 for the address bit setup.

6
Figure 2-4
Address
1
2
3
4
5
6
7
8
1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
……
…………………………………………………………………
254
OFF
ON
ON
ON
ON
ON
ON
ON
255
ON
ON
ON
ON
ON
ON
ON
ON
Table 2-1
2.3.4 Baud Rate and Parity Setup
The functions which need to be set between analog speed dome and HDCVI speed dome, which
will be introduced separately.
2.3.4.1 Analog Speed Dome
It is to set parity and baud rate of the speed dome. 5 and 6 bit is the setting bit of parity while 7
and 8 are the setting bit of baud rate, the label is shown in Figure 2-5, please refer to Table 2-2
and Table 2-3 for the setting.
Figure 2-5
5
6
Parity
OFF
OFF
NONE
ON
OFF
EVEN
OFF
ON
ODD
ON
ON
NONE
Table 2-2
7
8
Baud Rate
OFF
OFF
9600bps
ON
OFF
4800bps
OFF
ON
2400bps
ON
ON
1200bps
Table 2-3
2.3.4.2 HDCVI Speed Dome
It is to set baud rate. 7 and 8 bit is the setting bit of baud rate. The label is shown in Figure 2-6;
please refer to Table 2-4 for the setting.

7
Figure 2-6
7
8
Baud Rate
OFF
OFF
9600bps
ON
OFF
4800bps
OFF
ON
2400bps
ON
ON
1200bps
Table 2-4
2.3.5 Terminal Matched Resistance Setup
There are two connection modes of device terminal 120Ωresistance, which has already existed
on the power board. Please refer to Figure 2-7 for more details.
120Ω
1-2
ON
2-3
OFF
Figure 2-7
Refer to Figure 2-9 for the default connection mode, at this moment, the jumper cap on the
power board is connected to the location 2~3 of the socket and 120Ω resistance hasn’t been
connected yet.
Figure 2-8
It needs to plug out the jumper cap from 2~3 location when it needs to connect to 120Ω
resistance, and then connect to the location of 1~2. In this case, 120Ωresistance is connected to
the circuit, which is shown in Figure 2-9.

8
Figure 2-9
2.4 Reset Button and Micro-SD Card Installation
There is a reset button on the PCB which is located on the speed dome lateral (attached with
label), the DIP switch is shown in Figure 2-10, the switch is moved to ON as 1. Reset button is
used for system reset. As for DIP switch: 1 is the setting bit of 120Ωmatched resistance, ON is
to connect to 120Ωmatched resistance, 2 is the neutral bit; 1 is the lowest bit and 2 is the
highest bit.
Figure 2-10

9
Note
For some other models, there are only reset button and DIP switch without any other buttons
which are located on the PCB of speed dome lateral (without label), please refer to the actual
device for installation.
SD card slot is located on the module control panel; it can be seen after you open the rear cover
which is shown in Figure 2-11. Please pay attention to the direction of pulling and plugging Micro-
SD card. First press the card slot downward slightly, move it towards the OPEN direction (refer to
the instruction on the slot) and the card slot will become loose, and then lay the SD card. Please
be noted that the card metal surface has to be corresponding with the golden finger of card slot,
and then press down the card slot slightly, move it towards CLOSE direction.
Figure 2-11
2.5 Speed Dome Installation
Note
The chapter can be applied to IR analog intelligent speed dome and IR network intelligent
speed dome and so on.
There are various types of brackets which can meet different application scenarios for the speed
dome, please refer to chapter 3 to chapter 6 for the installation methods. It is to take analog
speed dome wall-mounted bracket as an example to install IR speed dome.
Step 1
Use quick mount screw on the speed dome and quick mount bayonet on the bracket to fix the
speed dome on the bracket, and then fix the speed dome firmly by using M6 inner hex screw,
which is shown in Figure 2-12.

10
Figure 2-12
Step 2
Connect the power cable, video cable, audio cable, RS-485 control cable, alarm cable, network
cable, high-frequency cable and optical fiber cable etc. well according to requirements, and then
use insulated rubber tape to twine the cable connection well respectively to make it waterproof.
Note
The video port is covered with heat-shrinkable tube with high shrinkage ratio, it needs to heat
and shrink the tubes on both sides after the video port is well connected, which is to make sure
the video port is moistureproof and waterproof.
Step 3
Fix the speed dome together with bracket on the wall, which is shown in Figure 2-13.
Figure 2-13
2.5.1 Install Quick Mount Connector
Twine Teflon tape over the thread of quick mount connector and rotate it into the tube thread of
wall-mounted bracket, use M4 stainless screw to fix it, which is shown in Figure 2-14, the thread
standard is G1 1/2 tube thread.

11
Figure 2-14
2.5.2 Speed Dome Cable
2.5.2.1 Cable Description
The camera is equipped with a multi-functional combination cable by default, which includes
power cable, video cable, audio cable, RS485 control cable, alarm cable, network cable, high-
frequency cable and optical fiber cable etc. The cable detail is shown in Figure 2-15.
Figure 2-15
Note
Different models have different cable combinations; please refer to the actual cable combination
for more details. The cable combination is the most comprehensive example shown in the figure
above.
It is prohibited to pull the cable to lift the speed dome when moving the device, the wrong way of
carrying device is shown in Figure 2-16.

12
Figure 2-16
2.5.2.2 Cable Connection
Buckle the safety hook of speed dome on the quick mount connector; connect the integrated
cable reserved by wall-mounted bracket to the corresponding power cable, video cable, audio
cable, RS485 control cable, alarm cable, network cable, high-frequency cable and optical fiber
cable etc. of the multi-functional combination cable of the speed dome (according to requirement),
and then use insulated rubber tape to twine the cable connection well to make it waterproof,
which is shown in Figure 2-16.
Note
During actual installation, make sure the wire diameter of the cable which is to connect to RS485
control cable can’t be too big; otherwise it will affect the control effect. Please refer to appendix 3
RS485 bus for relevant introduction.
2.5.2.3 Alarm Cable Connection
The alarm cable connection mode and config steps are shown as follows:
Step 1
Connect alarm input device to the ALARM IN and ALARM GND of the user cable.
Step 2
Connect alarm output device to the ALARM OUT and ALARM COM of the user cable, alarm
output is the relay switch output.
Step 3
Open the device WEB interface, make corresponding settings to the alarm input and output
device in “Setup > Event > Alarm Setup". The alarm input of WEB is corresponding to the alarm
input of the user cable. It is to set the corresponding NO and NC output according to the high and
low level signal generated by alarm input device when alarm triggers.
Step 4
Set the alarm output situation of user cable on the WEB.
2.5.2.4 Connect Speed Dome GND Cable
Connect the power line YELLOW & GREEN of the combination cable to the lightning protection
device, and make sure the lightning protection device is well grounded.

13
3Wall-mounted Bracket Installation
IR intelligent speed dome mainly takes wall mount, here it takes wall mount as an example to
introduce the installation components and modes of the speed dome.
3.1 Mounting Components and Dimension
The dimension of wall-mounted bracket is shown in Figure 3-1; the dimension of quick mount
connector is shown in Figure 3-2.
Figure 3-1
Figure 3-2