Dahua ITC237-PU1B-IR User manual

2.0MP CMOS HD Camera Web Operation Manual
Version 1.0.1

i
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 90-240V.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
Please keep package material well in case you need to send it back to your local retailer or
manufacturer for maintenance work.
Non-original package material may result in device damage during the transportation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection in case there is any
emergency situation.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series camera should be installed in a cool, dry place away from direct sunlight or strong light,
inflammable, explosive substances and etc.
The working temperature ranges from -30℃~ to +60℃. Please keep it away from the electromagnetic
radiation object and environment.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Usually we recommend thunder-proof device to prevent thunder strike.
The GND port of the product shall be grounded to further enhance the reliability of the device.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.

ii
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance work.
Use the dry soft cloth to clean the device.
If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean
the device. Finally use the dry cloth to clean the device.

iii
About the Manual
This manual is for reference only. Slight difference may be found in the user interface.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks mentioned are the properties of their respective owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website or contact your local retailer for more information.

iv
Table of Contents
1Web............................................................................................................................... 1
1.1 First Time Log in............................................................................................... 1
1.2 Non-first Time Login.......................................................................................... 4
1.3 System Menu.................................................................................................... 4
2Preview.......................................................................................................................... 5
2.1 Video Bit Stream Bar ........................................................................................ 5
2.2 Preview Window Switch.................................................................................... 6
2.3 Common Function Bar...................................................................................... 8
2.4 Monitor Window Switch................................................................................... 11
3Query........................................................................................................................... 12
3.1 Picture Query.................................................................................................. 12
3.1.1 SD Picture ................................................................................................ 12
3.1.2 Picture Attribute........................................................................................ 13
3.1.3 PC Picture ................................................................................................ 13
3.2 Record Query.................................................................................................. 14
3.2.1 Record...................................................................................................... 14
3.2.2 Water Mark............................................................................................... 15
3.3 Plate Query..................................................................................................... 16
4Configure..................................................................................................................... 18
4.1 ITC.................................................................................................................. 18
4.1.1 Guide Setup.............................................................................................. 18
4.1.2 Snapshot .................................................................................................. 19
4.1.3 Intelligence ............................................................................................... 21
4.1.4 OSD Config .............................................................................................. 22
4.1.5 Extra Device ............................................................................................. 25
4.1.6 Plate White/Black List............................................................................... 26
4.1.7 Intelligence Default................................................................................... 31
4.2 Camera........................................................................................................... 31
4.2.1 Attribute.................................................................................................... 31
4.2.2 Video ........................................................................................................ 34
4.3 Network........................................................................................................... 37
4.3.1 TCP/IP...................................................................................................... 37
4.3.2 ONVIF....................................................................................................... 39
4.3.3 IP Filter..................................................................................................... 39
4.4 Event............................................................................................................... 40
4.4.1 Alarm........................................................................................................ 40
4.4.2 Abnormity ................................................................................................. 41

v
4.5 Storage........................................................................................................... 43
4.5.1 Point ......................................................................................................... 43
4.5.2 Local......................................................................................................... 43
4.5.3 FTP........................................................................................................... 44
4.5.4 Client ........................................................................................................ 45
4.5.5 Path.......................................................................................................... 46
4.6 System............................................................................................................ 47
4.6.1 General..................................................................................................... 47
4.6.2 Account..................................................................................................... 49
4.6.3 Default...................................................................................................... 52
4.6.4 Import/Export............................................................................................ 53
4.6.5 Auto Maintain............................................................................................ 53
4.6.6 Upgrade.................................................................................................... 54
4.7 Information...................................................................................................... 54
4.7.1 Version ..................................................................................................... 54
4.7.2 Log............................................................................................................ 55
4.7.3 Online User............................................................................................... 56
5Alarm........................................................................................................................... 57
6Logout ......................................................................................................................... 58

1
1 Web
The device supports device access and management via WEB on PC.
Note:
Interface and settings here are for reference only.
1.1 First Time Log in
Open IE and input HD intelligent traffic camera IP address in the address column. For example, if your
IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address column. See Figure 1-1 IE.
Figure 1-1 IE
System pops up warning information to ask you whether install webrec.cab control or not. Please click
yes button.
If you can’t download the ActiveX file, please modify your settings as follows. See Figure 1-2.
Input your IP
address here.

2
Figure 1-2 Security Settings
After installation, the interface is shown as below. See Figure 1-3.
Please input your user name and password.
Follow system instructions to change password, and click OK.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
You can go to Setup>System>Account>User Name to change password.

3
Figure 1-3 Login Interface
After you logged in, HD intelligent traffic camera web homepage is shown as in Figure 1-4.
Note:
Download and install plug-in if you cannot enter the homepage.
Figure 1-4 Web Homepage

4
1.2 Non-first Time Login
Step 1. Open IE and input HD intelligent traffic camera IP address in the address column.
Step 2. Please input your user name and password. Click Login.
1.3 System Menu
System menu is shown as in Figure 1-5.
Figure 1-5 System Menu
Tab
Function
Preview
Installation debugging, adjust video and image window, record video and image,
set client image parameter.
Query
Query image and record in different types, watermark and vehicle pass record.
Setup
Set ITC rule, camera attributed, network, event, storage, system and view
system info.
Alarm
Set alarm prompt.
Logout
Logout WEB client.
Table 1-1
The followings are common buttons you may see on WEB. See Table 1-2.
Button
Note
Click this button, and click OK to restore system default settings.
Click this button, each parameter will resume to its latest saved
parameter.
After parameter is set, click this button to save.
Table 1-2

5
2 Preview
Click Live tab, system will show Live page. Here you can view live video, image, snapshot, record and
etc. See Figure 2-1.
Figure 2-1 Live
There are five sections:
Section 1: Video bit stream bar
Section 2: Preview window switch
Section 3: Common function bar
Section 4: System menu
Section 5: Monitor window switch
2.1 Video Bit Stream Bar
T he video bit stream bar interface is shown as in Figure 2-2.
Figure 2-2 Video Bit Stream Bar
Please refer to the following sheet for detailed information.

6
Parameter
Function
Main stream
You can use main stream to record video record, network
monitor function under normal network environment. You can set
resolution within its supported range.
Extra stream
It is a substitute for main stream under insufficient band width.
Protocol
Select video monitoring protocol, currently support TCP only.
Fluency
Select image fluency.
2.2 Preview Window Switch
The preview window switch interface is shown as in Figure 2-3 Preview Window Switch.
Figure 2-3 Preview Window Switch
---- Aspect ratio, adjust image to original size or best fit.
----Window switch to large window and display adjusting window. See Figure 2-8.
is full screen button. Te exit full screen, double click or press Esc.
Click to switch to large window.

7
Figure 2-4 Large Window
Icon
Name
Note
Original size
Original size and best-bit size switch. Click to
switch to original size.
Image adjustment
Display image adjustment window. Click to then
off image adjustment.
Table 2-1
Click on the right. See Figure 2-5 Adjusting Window.

8
Figure 2-5 Adjusting Window
Note:
All the operations here apply to WEB end only.
Please go to “Setup->Camera->Attributes” to set.
Please refer to the following sheet for detailed information.
Parameter
Function
Video
setup
It is to adjust monitor video brightness.
It is to adjust monitor video contrast.
It is to adjust monitor video hue.
It is to adjust monitor video saturation.
Reset
Reset brightness, contrast, hue and saturation to system default
values.
2.3 Common Function Bar
The common function bar interface is shown as in Figure 2-6.
Figure 2-6 Common Function Bar
Please refer to the following sheet for detailed information.
Icon
Name
Note
Record Type
Select record file format, default is dav.
Receive
Pictures
Check this option, system will auto records snapshots. RS485,
RS232, video detection and others trigger snapshot, while
recording plate, vehicle color, speed and other info will shown
below.
Manually
Snapshot
Click it, to snapshot video.
Snapshots are save to path set in “Setup->Camera-
>Video>Path”.
Partial Zoon
In
Click this key, in video window, drag mouse to any area, the
area will be zoomed in. Right click select exit or left click
to exit.
Snapshot
Click it, snapshot picture from video stream, and save to set
path.
Record
Click it, to start recording.
Click to stop recording.

9
Icon
Name
Note
Install
Draw debugging plate area, adjust camera focus and set local
text.
Table 2-2
Click to enter installation interface.
Figure 2-7
Steps to debug:
Step 1. Set focus zoom mode, used to identify vehicle. See Table 2-3.
Parameter
Note
Auto Focus
Auto adjust focus
Note:
This function is for ITC237-PU1B-IR, ITC237-PU1B-L camera only.
Auto adjust lens.
Note:
This function is for ITC237-PW1B-IRZ camera.

10
Parameter
Note
Manual Config
Manual config set focos parameter to focus on vehicle.
Zoom：
Speed：There are 3 levels.
- and +: click to add speed, click to reduce speed；or
directly drag bar to zoom in and out.
Focus：
Speed：There are 3 levels.
- and +: click to add speed, click to reduce speed；or
directly drag bar to set focus.
Note:
This function is for ITC237-PW1B-IRZ camera.
Manual config set rear focus.
Speed：There are 3 levels.
- and +: click to add speed, click to reduce speed；or
directly drag bar to set rear focus.
Note:
This function is for ITC237-PU1B-IR, ITC237-PU1B-L camera only.
Restore All
Restore all settings to default.
Pause/Resume
Resume：When you click Pause. Video pauses, then click Resume to
continue playing.
When you click Resume. Video continue playing, then click Resume to
pause.
Refresh
View latest status.
Table 2-3
Step 2. Select line type to configure. See Table 2-4.
Parameter
Note
Region
Set region to delete. Region is within red line.
Detect Line
Draw detect line of trigger of snapshot.
Detect line is green.
Shield Area
Set shield area. In this area, it will not identify vehicle plate. You can set up to
2 shield areas.
Shield area is within grey box.
Table 2-4
Step 3. In viewing field, draw lines.
Note:
Click Redraw to delete current config.
Step 4. Adjust plate snapshot position to be in the yellow box.
Try your best to make this box match actual plate position and size in the video.

11
Note:
Plate best width range is 140~160. If you want to modify, go to Setup>ITC>Intelligent>Video
Analysis>Recognition.
Step 5. Set local plate.
Step 6. Click Save.
2.4 Monitor Window Switch
The monitor window switch interface is shown as in Figure 2-8 Monitor Window Switch.
Figure 2-8 Monitor Window Switch
---- View pixel in pane.
----Display in single window.
---- Display in four windows.
---- Display in full screen.

12
3 Query
3.1 Picture Query
3.1.1 SD Picture
Click query button, you can see an interface is shown as in Figure 3-1 SD Picture Query.
Click Open Local, select picture you want to verify and click Water Verify, then you can view the result.
Select the picture, click Open to preview.
Figure 3-1 SD Picture Query
Parameter
Note
Start Time
Set picture query start time.
End Time
Set picture query end time.
Event Type
Query all pictures, or filter picture by event type.
Plate
Check this plate, and filter picture by plate feature.
Click this button to download link record.
Note:
After link video is enabled, all violation pictures have this icon. However,
whether there is record depends on actual condition.
Table 3-1
Step 1. Enter parameter of query picture, click Search. In file list it shows all matched picture files.
Step 2. Select picture you want, click Download.
Step 3. In pop-up box, set picture storage path and the system starts to download picture to local PC. If
you want to preview picture, click Open or double click picture.

13
3.1.2 Picture Attribute
Select Search>Picture Query>Picture Attribute.
Set download picture attribute time and naming method.
Select download picture by file or by time.
Figure 3-2
Parameter
Note
Download
Time
Create time: when picture is downloaded on PC, picture attribute time is
PC time.
Snap time：when picture is downloaded on PC, picture attribute time is
device-end time.
Download
Mode
Selected file：Select picture you need（select one or more pictures, as
batch download），click Download, system pops up box.
Selected time：Directly click Download, system starts to auto download
all pictures within start time and end time.
Reset
Reset download picture naming to default method.
Help
View naming rule of download picture.
Table 3-2
3.1.3 PC Picture
Select Query>Picture Query>PC Picture, check whether picture has been modified via watermark.

14
Figure 3-3
Step 1. Click Open Local, select folder of picture you want to verify.
Step 2. Select picture.
Step 3. Click Water Verify, see results in list.
You can click Open or double click picture to preview.
3.2 Record Query
3.2.1 Record
Click Query>Record Query>Record, you can see an interface is shown as in Figure 3-4 Record
Query.