Dahua PFH610N-IR User manual

HD Network (IR) Housing Zoom Camera
Installation Manual
Version 1.0.0

i
Table of Contents
1GENERAL INTRODUCTION ..............................................................................1
1.1 Overview...........................................................................................................................................1
1.2 Features............................................................................................................................................1
1.3 Dimensions.......................................................................................................................................1
2INSTALLATION INSTRUCTION GUIDE.............................................................3
2.1 Lock/Unlock Housing.......................................................................................................................3
2.2 Camera Installation..........................................................................................................................3
3BRACKET INSTALLATION GUIDE ....................................................................5
3.1 General Bracket Installation ............................................................................................................5
3.2 Special Bracket Installation (Compact design, concealed cable exit)..........................................5
3.3 Bracket Types ..................................................................................................................................6
APPENDIX TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS .......................8

ii
Welcome
Thank you for purchasing our HD network (IR) housing zoom camera!
Please read the following safeguards and warnings carefully before you install or use the
product!

iii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the HD network (IR) housing zoom camera before completing installation.
Do not place objects on the HD network (IR) housing zoom camera.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
The HD network (IR) housing zoom camera should be installed in a cool, dry place away from
direct sunlight, inflammable, explosive substances and etc.
Please keep sound ventilation.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

1
1General Introduction
1.1 Overview
The HD network housing zoom camera (“camera”) adopts all-weather compact design. It is
suitable for various environments. Its housing has IP66 compliance and it supports various
installation modes such as ceiling mount, wall mount, pedestal mount and etc.
1.2 Features
All-weather compact design, bracket supports upright/upside down installation, easy
maintenance work.
Airproof design, sustain high temperature, strong wind, rainstorm and dustproof.
Suitable for various environments.
1.3 Dimensions
Please refer to Figure 1-1 for PFH610N/PFH610N-H dimensions information. The unit is mm.
Figure 1-1
Please refer to Figure 1-2 for PFH610N-IR dimensions information. The unit is mm.

2
Figure 1-2
Please refer to Figure 1-3 for PFH610N-W/PFH610N-IR-W dimensions information. The unit is
mm.
Figure 1-3

3
2Installation Instruction Guide
2.1 Lock/Unlock Housing
You can use inner hex wrench (5.0mm) to fix or loosen the two M6 screws on both sides of the
housing to lock or unlock the housing. See Figure 2-1.
Figure 2-1
Important
Before you lock the housing, please make sure the waterproof gasket is in the right
position. See Figure 2-2. Otherwise it may affect the waterproof capability of the housing.
Figure 2-2
2.2 Camera Installation
Step 1: Fix the camera on the camera bracket.
Step 2: Secure the camera bracket on the case. See Figure 2-3.
Please refer to the following sheet for detailed information.
SN
Name

4
1
Camera and the components of the main
control board
2
IR light board fastener and etc
3
Housing components
Figure 2-3

5
3Bracket Installation Guide
3.1 General Bracket Installation
The camera can use the bracket of the thread hole to install. The general bracket thread hole
(M6) on the camera is shown as below. See Figure 3-1.
Figure 3-1
3.2 Special Bracket Installation (Compact design, concealed cable exit)
Step 1: Pull the cable through the inside of the bracket. See Figure 3-2.
Step 2: Secure the bracket on the camera. See Figure 3-3.
Step 3: Put the waterproof joint on the cables and then secure firmly. See Figure 3-4.
Figure 3-2

6
Figure 3-3
Figure 3-4
3.3 Bracket Types
You can refer to the following sheet for different bracket models if you want to use different
mount modes.
Installation
Mode
Reference Figure
Bracket Model
Ceiling
Mount
PFB600W

7
Installation
Mode
Reference Figure
Bracket Model
Wall Mount 1
PFB602W
Pedestal
Mount
PFA160
Pedestal
Mount 1
The bracket and the housing installation
position adopt symmetric design. The bracket
can be installed upside-down.
PFB601W
Pedestal
Mount 2
PFB601W+PFA112
（200mm）or PFA113
（400mm）
The bracket is not a standard accessory of the camera. Please contact your local retailer
for more information.

8
Appendix Toxic or Hazardous Materials or Elements
Component
Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
Sheet Metal
○
○
○
○
○
○
Plastic Parts
○
○
○
○
○
○
PCB
○
○
○
○
○
○
Fastener
○
○
○
○
○
○
Connection
Cable
○
○
○
○
○
○
Package
○
○
○
○
○
○
Accessories
○
○
○
○
○
○
Note
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in
the parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006
standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous
substance or elements contained in products will not leak or mutate so that the use of these
(substances or elements) will not result in any severe environmental pollution, any bodily injury or
damage to any assets. The consumer is not authorized to process such kind of substances or
elements, please return to the corresponding local authorities to process according to your local
government statutes.
Note
This manual is for reference only. Slight difference may be found in the user
interface.
All the designs and software here are subject to change without prior written
notice.
All trademarks and registered trademarks mentioned are the properties of their
respective

9
owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website or contact your local service engineer for more
information.