Daikin SkyAir RZQ200 250C7Y1B User manual

SkyAir
RZQ200 · 250C7Y1B
R-410A Heat Pump 50Hz
SiBE26 - 701

SiBE26-701
Table of Contents i
SkyAir R-410A Heat Pump
GQLII 50Hz
1. Introduction .............................................................................................v
1.1 Safety Cautions ........................................................................................v
1.2 PREFACE ............................................................................................... ix
Part 1 General Information ........................................................... 3
1. Model Name and Power Supply..............................................................4
2. Possible Combinations and Standard Capacity for Twin,
Triple and Double Twin Operation ..........................................................5
3. External Appearance...............................................................................6
Part 2 Specifications .................................................................... 7
1. Specifications ..........................................................................................8
1.1 Outdoor Units ...........................................................................................8
2. Electric Characteristics............................................................................9
Part 3 Remote Controller ............................................................ 11
1. Wired Remote Controller.......................................................................12
1.1 Features .................................................................................................12
1.2 Installation ..............................................................................................14
2. Wireless Remote Controller ..................................................................16
2.1 Features .................................................................................................16
3. Method of Operating Remote Controller ...............................................18
3.1 The INSPECTION / TEST Button...........................................................18
3.2 Maintenance Mode Setting.....................................................................19
3.3 Operation of the Remote Controller’s Inspection /
Test Operation Button ............................................................................21
3.4 Remote Controller Service Mode ...........................................................22
Part 4 Field Setting ..................................................................... 23
1. Field Setting of Indoor Unit....................................................................24
1.1 Field Setting from Remote Controller .....................................................24
1.2 Setting Contents and Code No. – SkyAir Indoor Unit ............................26
1.3 Detailed Explanation of Setting Modes ..................................................27
2. Field Setting of Outdoor Unit.................................................................32
2.1 Field Setting from Remote Controller .....................................................32
2.2 Field Setting by Demand Adapter ..........................................................35
2.3 Field Setting from Outdoor Unit PC Board .............................................38
3. Emergency Operation ...........................................................................44
3.1 Emergency Operation (Forced Operation) Setting Procedure ...............44
3.2 Test Operation Setting Procedure..........................................................45
3.3 Emergency Operation (When the Remote Controller is Lost) ................45

SiBE26-701
ii Table of Contents
Part 5 Function and Operation ................................................... 47
1. Indoor Unit.............................................................................................48
1.1 Function Details......................................................................................48
2. Outdoor Unit..........................................................................................54
2.1 Function List ...........................................................................................54
2.2 Flow Chart of Outdoor Unit.....................................................................55
2.3 Table of Functions and Operations ........................................................57
2.4 Function Details......................................................................................61
3. List of Electrical and Functional Parts ...................................................71
3.1 Outdoor Unit ...........................................................................................71
4. Operation Range...................................................................................72
4.1 Operation Limits .....................................................................................72
Part 6 Troubleshooting ............................................................... 73
1. Maintenance Inspections ......................................................................75
1.1 Optimal Operation Condition ..................................................................75
1.2 Refrigerant Saturation Curve (R-410A) ..................................................78
1.3 Cautions in Handling New Refrigerant ...................................................79
2. Troubleshooting Based on Equipment Condition..................................83
2.1 Troubleshooting Based on Equipment Condition ...................................83
2.2 Equipment does not Operate .................................................................84
2.3 Indoor Fan Operates, but Compressor does not....................................85
2.4 Cooling/Heating Operation Starts but Stops Immediately ......................87
2.5 After Equipment Shuts Down, It cannot be Restarted for a While..........89
2.6 Equipment Operates but does not Provide Cooling ...............................90
2.7 Equipment Operates but does not Provide Heating ...............................92
2.8 Equipment Discharges White Mist .........................................................93
2.9 Equipment Produces Loud Noise or Shakes..........................................94
2.10 Equipment Discharges Dust...................................................................95
2.11 Remote Controller LCD Displays "88" ....................................................96
2.12 Swing Flap does not Move.....................................................................97
3. Procedure of Self-Diagnosis by LED.....................................................98
3.1 Troubleshooting by LED on Outdoor Unit PC Board..............................98
4. Diagnosis by Remote Controller ...........................................................99
4.1 Confirm Method of Malfunction Code.....................................................99
4.2 Remote Controller Display Malfunction Code and Contents ................102
4.3 “A1” Failure of Indoor Unit PC Board .....................................................104
4.4 “A3” Malfunction of Drain Water Level System (Float Type) .................105
4.5 “A6” Malfunction of Indoor Unit Fan Motor ............................................107
4.6 “A6”Malfunction of Indoor Unit Fan Motor ............................................109
4.7 “A6”Indoor Unit Fan Motor Overload, Overcurrent, Lock .....................110
4.8 “A7”Malfunction of Swing Flap Motor ...................................................112
4.9 “AF” Failure of Drain System .................................................................113
4.10 “AJ”Malfunction of Capacity Determination Device..............................114
4.11 “C4” Malfunction of Heat Exchange Temperature Sensor System........115
4.12 “C9” Malfunction of Suction Air Temperature Sensor System ...............116
4.13 “CC”Malfunction of Humidity Sensor System ........................................117
4.14 “CJ” Malfunction of Remote Controller Air Thermistor...........................118
4.15 “E1”Failure of Outdoor Unit PC Board...................................................119
4.16 “E3”Abnormal High Pressure Level ......................................................120

SiBE26-701
Table of Contents iii
4.17 “E4”Low Pressure System Malfunction ................................................122
4.18 “E5” Inverter Compressor Motor Lock ...................................................124
4.19 “E7”Malfunction of Outdoor Unit Fan Motor..........................................125
4.20 “E9”Malfunction of Moving Part of Electronic Expansion Valve............128
4.21 “F3”Malfunction of Discharge Pipe Temperature..................................130
4.22 “H3” Abnormal High Pressure Switch....................................................132
4.23 “H7”Abnormal Outdoor Fan Motor Signal .............................................134
4.24 “H9” “J3” “J5” “J6” “J7” “J8”Malfunction of Thermistor System ...............136
4.25 “JA”Malfunction of High Pressure Sensor............................................138
4.26 “JC”Malfunction of Low Pressure Sensor.............................................140
4.27 “L1” Faulty Outdoor Inverter PC board ..................................................142
4.28 “L4”Radiation Fin Temperature Increased ...........................................143
4.29 “L5” Momentary Overcurrent of Inverter Compressor ...........................145
4.30 “L8”Inverter Compressor Overcurrent ..................................................147
4.31 “L9”Compressor Inverter Start up Error ...............................................149
4.32 “LC”Malfunction of Transmission between Inverter and
Control PC Board .................................................................................151
4.33 “P1”Inverter Over-Ripple Protection......................................................154
4.34 “PJ” Defective Combination of Inverter and Fan Driver ........................155
4.35 “U0”Gas Shortage (Malfunction) ..........................................................156
4.36 “U1”Reverse Phase...............................................................................157
4.37 “U2”Power Supply Insufficient or Instantaneous Failure ......................158
4.38 “U4”Malfunction of Transmission
(between Indoor and Outdoor Unit)......................................................161
4.39 “U5”Malfunction of Transmission
(between Indoor Unit and Remote Controller)......................................163
4.40 “U8”Transmission Error between Main Remote Controller and
Sub Remote Controller.........................................................................164
4.41 “U9”Malfunction of Transmission between Indoor and
Outdoor Units in the Same System ......................................................165
4.42 “UA”Malfunction of Field Setting Switch and Transmission Line ..........167
4.43 “UC”Centralized Address Duplicated ....................................................169
4.44 “UE” Malfunction of Transmission between Centralized Controller and
Indoor Unit............................................................................................170
4.45 “UF” Transmission System Malfunction
(between Indoor and Outdoor Units)....................................................172
Part 7 Appendix......................................................................... 185
1. Items Improved from the Existing Models ...........................................186
2. Piping Diagrams..................................................................................187
2.1 Pair .......................................................................................................187
2.2 Twin......................................................................................................188
2.3 Triple ....................................................................................................189
2.4 Double Twin .........................................................................................190
3. Wiring Diagrams..................................................................................191
3.1 Outdoor Unit .........................................................................................191

SiBE26-701
iv Table of Contents
Part 8 Removal Procedure ........................................................ 193
1. RZQ200 · 250C7Y1B .........................................................................194
1.1 Procedure for Removal Related to Outside Panel ...............................194
1.2 Procedure for Removal of Fan Motor ...................................................195
1.3 Procedure for Removal of Electrical Component Assembly.................196
1.4 Procedure for Removal of PC Board....................................................197
1.5 Procedure for Removal of Electronic Expansion Valve and
Solenoid Valve .....................................................................................199
1.6 Procedure for Removal of Pressure Switch,
Pressure Sensor, etc............................................................................200
1.7 Procedure for Removal of Compressor................................................201
1.8 Procedure for Removal of Thermistor ..................................................202
Index ............................................................................................. i
Drawings & Flow Charts ................................................................ v

SiBE26-701 Introduction
v
1. Introduction
1.1 Safety Cautions
Cautions and
Warnings
Be sure to read the following safety cautions before conducting repair work.
The caution items are classified into “ Warning” and “ Caution”. The “ Warning”
items are especially important since they can lead to death or serious injury if they are not
followed closely. The “ Caution” items can also lead to serious accidents under some
conditions if they are not followed. Therefore, be sure to observe all the safety caution items
described below.
About the pictograms
This symbol indicates an item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates a prohibited action.
The prohibited item or action is shown inside or near the symbol.
This symbol indicates an action that must be taken, or an instruction.
The instruction is shown inside or near the symbol.
After the repair work is complete, be sure to conduct a test operation to ensure that the
equipment operates normally, and explain the cautions for operating the product to the
customer
1.1.1 Caution in Repair
Warning
Be sure to disconnect the power cable plug from the plug socket before
disassembling the equipment for a repair.
Working on the equipment that is connected to a power supply can cause an
electrical shook.
If it is necessary to supply power to the equipment to conduct the repair or
inspecting the circuits, do not touch any electrically charged sections of the
equipment.
If the refrigerant gas discharges during the repair work, do not touch the
discharging refrigerant gas.
The refrigerant gas can cause frostbite.
When disconnecting the suction or discharge pipe of the compressor at the
welded section, release the refrigerant gas completely at a well-ventilated
place first.
If there is a gas remaining inside the compressor, the refrigerant gas or
refrigerating machine oil discharges when the pipe is disconnected, and it can
cause injury.
If the refrigerant gas leaks during the repair work, ventilate the area. The
refrigerant gas can generate toxic gases when it contacts flames.
The step-up capacitor supplies high-voltage electricity to the electrical
components of the outdoor unit.
Be sure to discharge the capacitor completely before conducting repair work.
A charged capacitor can cause an electrical shock.
Do not start or stop the air conditioner operation by plugging or unplugging the
power cable plug.
Plugging or unplugging the power cable plug to operate the equipment can
cause an electrical shock or fire.

Introduction SiBE26-701
vi
1.1.2 Cautions Regarding Products after Repair
Caution
Do not repair the electrical components with wet hands.
Working on the equipment with wet hands can cause an electrical shock.
Do not clean the air conditioner by splashing water.
Washing the unit with water can cause an electrical shock.
Be sure to provide the grounding when repairing the equipment in a humid or
wet place, to avoid electrical shocks.
Be sure to turn off the power switch and unplug the power cable when cleaning
the equipment.
The internal fan rotates at a high speed, and cause injury.
Do not tilt the unit when removing it.
The water inside the unit can spill and wet the furniture and floor.
Be sure to check that the refrigerating cycle section has cooled down
sufficiently before conducting repair work.
Working on the unit when the refrigerating cycle section is hot can cause burns.
Use the welder in a well-ventilated place.
Using the welder in an enclosed room can cause oxygen deficiency.
Warning
Be sure to use parts listed in the service parts list of the applicable model and
appropriate tools to conduct repair work. Never attempt to modify the
equipment.
The use of inappropriate parts or tools can cause an electrical shock,
excessive heat generation or fire.
When relocating the equipment, make sure that the new installation site has
sufficient strength to withstand the weight of the equipment.
If the installation site does not have sufficient strength and if the installation
work is not conducted securely, the equipment can fall and cause injury.
Be sure to install the product correctly by using the provided standard
installation frame.
Incorrect use of the installation frame and improper installation can cause the
equipment to fall, resulting in injury.
For integral units
only
Be sure to install the product securely in the installation frame mounted on a
window frame.
If the unit is not securely mounted, it can fall and cause injury.
For integral units
only
Be sure to use an exclusive power circuit for the equipment, and follow the
technical standards related to the electrical equipment, the internal wiring
regulations and the instruction manual for installation when conducting
electrical work.
Insufficient power circuit capacity and improper electrical work can cause an
electrical shock or fire.

SiBE26-701 Introduction
vii
1.1.3 Inspection after Repair
Be sure to use the specified cable to connect between the indoor and outdoor
units. Make the connections securely and route the cable properly so that there
is no force pulling the cable at the connection terminals.
Improper connections can cause excessive heat generation or fire.
When connecting the cable between the indoor and outdoor units, make sure
that the terminal cover does not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section can cause
an electrical shock, excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cable can cause an electrical shock or fire.
Placing heavy items on the power cable, and heating or pulling the power cable
can damage the cable.
Do not mix air or gas other than the specified refrigerant (R-410A) in the
refrigerant system.
If air enters the refrigerating system, an excessively high pressure results,
causing equipment damage and injury.
If the refrigerant gas leaks, be sure to locate the leak and repair it before
charging the refrigerant. After charging refrigerant, make sure that there is no
refrigerant leak.
If the leak cannot be located and the repair work must be stopped, be sure to
perform pump-down and close the service valve, to prevent the refrigerant gas
from leaking into the room. The refrigerant gas itself is harmless, but it can
generate toxic gases when it contacts flames, such as fan and other heaters,
stoves and ranges.
When replacing the coin battery in the remote controller, be sure to disposed
of the old battery to prevent children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Warning
Caution
Installation of a leakage breaker is necessary in some cases depending on the
conditions of the installation site, to prevent electrical shocks.
Do not install the equipment in a place where there is a possibility of
combustible gas leaks.
If a combustible gas leaks and remains around the unit, it can cause a fire.
Be sure to install the packing and seal on the installation frame properly.
If the packing and seal are not installed properly, water can enter the room and
wet the furniture and floor.
For integral units
only
Warning
Check to make sure that the power cable plug is not dirty or loose, then insert
the plug into a power outlet all the way.
If the plug has dust or loose connection, it can cause an electrical shock or fire.
If the power cable and lead wires have scratches or deteriorated, be sure to
replace them.
Damaged cable and wires can cause an electrical shock, excessive heat
generation or fire.
Do not use a joined power cable or extension cable, or share the same power
outlet with other electrical appliances, since it can cause an electrical shock,
excessive heat generation or fire.

Introduction SiBE26-701
viii
1.1.4 Using Icons
Icons are used to attract the attention of the reader to specific information. The meaning of each
icon is described in the table below:
1.1.5 Using Icons List
Caution
Check to see if the parts and wires are mounted and connected properly, and
if the connections at the soldered or crimped terminals are secure.
Improper installation and connections can cause excessive heat generation,
fire or an electrical shock.
If the installation platform or frame has corroded, replace it.
Corroded installation platform or frame can cause the unit to fall, resulting in
injury.
Check the grounding, and repair it if the equipment is not properly grounded.
Improper grounding can cause an electrical shock.
Be sure to measure the insulation resistance after the repair, and make sure
that the resistance is 1 Mohm or higher.
Faulty insulation can cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage can cause the water to enter the room and wet the furniture
and floor.
Icon Type of
Information
Description
Note:
Note A “note” provides information that is not indispensable, but may
nevertheless be valuable to the reader, such as tips and tricks.
Caution
Caution A “caution” is used when there is danger that the reader, through
incorrect manipulation, may damage equipment, loose data, get
an unexpected result or has to restart (part of) a procedure.
Warning
Warning A “warning” is used when there is danger of personal injury.
Reference A “reference” guides the reader to other places in this binder or
in this manual, where he/she will find additional information on a
specific topic.

SiBE26-701 Introduction
ix
1.2 PREFACE
Thank you for your continued patronage of Daikin products.
This is the new service manual for Daikin's Year 2007 RZQ-C series Heat Pump System.
Daikin offers a wide range of models to respond to building and office air conditioning needs.
We are confident that customers will be able to find the models that best suit their needs.
This service manual contains information regarding the servicing of RZQ-C series R-410A Heat
Pump System.
May, 2007
After Sales Service Division

Introduction SiBE26-701
x

SiBE26-701
1
SkyAir GQLII Series
— Cooling Only —
Model Series
Class Pair
200 250
Indoor Units FDQ 200B7V3B 250B7V3B
Outdoor Units RZQ 200C7Y1B 250C7Y1B
Class Twin
100 125
Indoor Units
FCQ 100C7VEB × 2 125C7VEB × 2
FBQ 100B7V3B × 2 125B7V3B × 2
FDQ — 125B7V3B × 2
FHQ 100BUV1B × 2 125BUV1B × 2
FUQ 100BUV1B × 2 125BUV1B × 2
FAQ 100BUV1B × 2 —
Outdoor Units RZQ 200C7Y1B 250C7Y1B
Class Triple
60 71
Indoor Units
FCQ 60C7VEB × 3 71C7VEB × 3
FFQ 60BV1B × 3 —
FBQ 60B7V1 × 3 71B7V3B × 3
FHQ 60BUV1B × 3 71BUV1B × 3
FUQ — 71BUV1B × 3
FAQ — 71BUV1B × 3
Outdoor Units RZQ 200C7Y1B
Class Double Twin
50 60
Indoor Units
FCQ 50C7VEB × 4 60C7VEB × 4
FFQ 50BV1B × 4 60BV1B × 4
FBQ 50B7V1 × 4 60B7V1 × 4
FHQ 50BUV1B × 4 60BUV1B × 4
Outdoor Units RZQ 200C7Y1B 250C7Y1B

SiBE26-701
2

SiBE26-701
General Information 3
Part 1
General Information
1. Model Name and Power Supply..............................................................4
2. Possible Combinations and Standard Capacity for Twin,
Triple and Double Twin Operation ..........................................................5
3. External Appearance...............................................................................6

Model Name and Power Supply SiBE26-701
4General Information
1. Model Name and Power Supply
Note: Power Supply Intake : Outdoor Units
Indoor Units Outdoor Units Power Supply
Ceiling Mounted Cassette Type
(Multi Flow)
FCQ50C7VEB RZQ200C7Y1B
3φ, 380-415V, 50Hz
FCQ60C7VEB RZQ200C7Y1B
FCQ71C7VEB RZQ200C7Y1B
FCQ100C7VEB RZQ200C7Y1B
Ceiling Mounted Cassette Type
(600x600 Multi Flow)
FFQ50BV1B RZQ200C7Y1B
FFQ60BV1B RZQ200C7Y1B
Ceiling Mounted Built-in Type
FBQ50B7V1 RZQ200C7Y1B
FBQ60B7V1 RZQ200C7Y1B
FBQ71B7V3B RZQ200C7Y1B
FBQ100B7V3B RZQ200C7Y1B
High Static Pressure Type FDQ200B7V3B RZQ200C7Y1B
Ceiling Suspended Type
FHQ50BUV1B RZQ200C7Y1B
FHQ60BUV1B RZQ200C7Y1B
FHQ71BUV1B RZQ200C7Y1B
FHQ100BUV1B RZQ200C7Y1B
Ceiling Suspended Cassette Type FUQ71BUV1B RZQ200C7Y1B
FUQ100BUV1B RZQ200C7Y1B
Wall Mounted Type FAQ71BUV1B RZQ200C7Y1B
FAQ100BUV1B RZQ200C7Y1B
Ceiling Mounted Cassette Type
(Multi Flow)
FCQ60C7VEB RZQ250C7Y1B
3φ, 380-415V, 50Hz
FCQ125C7VEB RZQ250C7Y1B
Ceiling Mounted Cassette Type
(600x600 Multi Flow) FFQ60BV1B RZQ250C7Y1B
Ceiling Mounted Built-in Type FBQ60B7V1 RZQ250C7Y1B
FBQ125B7V3B RZQ250C7Y1B
High Static Pressure Type FDQ125B7V3B RZQ250C7Y1B
FDQ250B7V3B RZQ250C7Y1B
Ceiling Suspended Type FHQ60BUV1B RZQ250C7Y1B
FHQ125BUV1B RZQ250C7Y1B
Ceiling Suspended Cassette Type FUQ125BUV1B RZQ250C7Y1B

SiBE26-701 Possible Combinations and Standard Capacity for Twin, Triple and Double Twin Operation
General Information 5
2. Possible Combinations and Standard Capacity for
Twin, Triple and Double Twin Operation
Possible Indoor Combination
Simultaneous Operation
Outdoor models
Twin Triple Double twin
RZQ200C7Y1B 100-100
(KHRQ22M20TA)
60-60-60
71-71-71
(KHRQ250H)
50-50-50-50
(3x KHQ22M20TA)
RZQ250C7Y1B 125-125
(KHRQ22M20TA) —60-60-60-60 (3x KHRQ22M20TA)

External Appearance SiBE26-701
6General Information
3. External Appearance
Indoor Units
Remote Controller
Outdoor Units
FCQ FFQ FBQ
FDQ FHQ FUQ
FAQ
Wireless Type
BRC7 Type
Wired Type
BRC1D52 Type
RZQ200C
RZQ250C

SiBE26-701
Specifications 7
Part 2
Specifications
1. Specifications ..........................................................................................8
1.1 Outdoor Units ...........................................................................................8
2. Electric Characteristics............................................................................9

Specifications SiBE26-701
8Specifications
1. Specifications
1.1 Outdoor Units
Heat Pump 50Hz Series <RZQ-C>
Notes:
★1 Indoor temp. : 27°CDB or 19°CWB / outdoor temp. : 35°CDB / Equivalent piping length : 7.5m, level difference : 0m.
( ) Shows maximum capacity.
★2 Indoor temp. : 20°CDB / outdoor temp. : 7°CDB or 6°CWB / Equivalent piping length : 7.5m, level difference : 0m.
( ) Shows maximum capacity.
Model RZQ200C7Y1B RZQ250C7Y1B
Power Supply 3 phase 50Hz 380~415V
★1 Cooling Capacity kW 20.0 24.1
★2 Heating Capacity kW 23.0 26.4
Casing Color Ivory White (5Y7.5/1), E type: Light Camel (2.5Y6.5/1.5)
Dimensions: (H×W×D) mm 1,680×930×765
Heat Exchanger Cross Fin Coil
Compressor
Type Hermetically Sealed Scroll Type
Piston Displacement m³/h 13.72
Number of Revolutions r.p.m 7,980
Motor Output
(2.2kW/60rps) kW 3.08×1
Starting Method Soft Start
Fan
Type Propeller Fan
Motor Output W 750×1
Air Flow Rate m³/min 171
Drive Direct Drive
Connecting
Pipes
Liquid Pipe mm φ9.5 (Brazing Connection) φ12.7 (Brazing Connection)
Gas Pipe mm φ22.2 (Brazing Connection)
Weight kg 183 184
Safety Devices High Pressure Switch, Fan Driver Overload Protector, Overcurrent Relay, Inverter Overload Protector, PC board fuse
Defrost Method Reversed cycle
Capacity Control % 14~100
Refrigerant
Refrigerant Name R-410A
Charge kg 8.3 9.3
Control Electronic Expansion Valve
Standard Accessories Installation Manual, Connection Pipes

SiBE26-701 Electric Characteristics
Specifications 9
2. Electric Characteristics
Unit combination Power supply Comp OFM IFM
Indoor Outdoor Hz-Volts Voltage range MCA TOCA MFA MSC RLA kW FLA kW FLA
FCQ50C7VEB ×4 RZQ200C7Y1B 50-400
Max.50Hz 415V
Min.50Hz 380V
16.6 18.6 20 — 14.7 0.75 0.7 0.056×4 0.3×4
FCQ60C7VEB ×3 RZQ200C7Y1B 50-400 16.6 18.6 20 — 14.7 0.75 0.7 0.056×3 0.4×3
FCQ71C7VEB ×3 RZQ200C7Y1B 50-400 16.9 18.9 20 — 14.7 0.75 0.7 0.056×3 0.5×3
FCQ100C7VEB ×2 RZQ200C7Y1B 50-400 16.8 18.8 20 — 14.7 0.75 0.7 0.120×2 0.7×2
FFQ50BV1B ×4 RZQ200C7Y1B 50-400 18.2 20.2 25 — 14.7 0.75 0.7 0.055×4 0.7×4
FFQ60BV1B ×3 RZQ200C7Y1B 50-400 17.5 19.5 20 — 14.7 0.75 0.7 0.055×3 0.7×3
FBQ50B7V1 ×4 RZQ200C7Y1B 50-400 18.2 20.2 25 — 14.7 0.75 0.7 0.085×4 0.7×4
FBQ60B7V1 ×3 RZQ200C7Y1B 50-400 18.1 20.1 25 — 14.7 0.75 0.7 0.125×3 0.9×3
FBQ71B7V3B ×3 RZQ200C7Y1B 50-400 18.1 20.1 25 — 14.7 0.75 0.7 0.125×3 0.9×3
FBQ100B7V3B ×2 RZQ200C7Y1B 50-400 17.4 19.4 20 — 14.7 0.75 0.7 0.135×2 1.0×2
FHQ50BUV1B ×4 RZQ200C7Y1B 50-400 17.8 19.8 20 — 14.7 0.75 0.7 0.062×4 0.6×4
FHQ60BUV1B ×3 RZQ200C7Y1B 50-400 17.2 19.2 20 — 14.7 0.75 0.7 0.062×3 0.6×3
FHQ71BUV1B ×3 RZQ200C7Y1B 50-400 17.2 19.2 20 — 14.7 0.75 0.7 0.062×3 0.6×3
FHQ100BUV1B×2 RZQ200C7Y1B 50-400 16.8 18.8 20 — 14.7 0.75 0.7 0.130×2 0.7×2
FUQ71BUV1B ×3 RZQ200C7Y1B 50-400 17.5 19.5 20 — 14.7 0.75 0.7 0.045×3 0.7×3
FUQ100BUV1B×2 RZQ200C7Y1B 50-400 17.6 19.6 20 — 14.7 0.75 0.7 0.090×2 1.1×2
FAQ71BUV1B ×3 RZQ200C7Y1B 50-400 16.3 18.3 20 — 14.7 0.75 0.7 0.043×3 0.3×3
FAQ100BUV1B×2 RZQ200C7Y1B 50-400 16.2 18.2 20 — 14.7 0.75 0.7 0.049×2 0.4×2
FDQ200B7V3B RZQ200C7Y1B 50-400 15.4 17.4 20 — 14.7 0.75 0.7 0.650 6.8
FCQ60C7VEB ×4 RZQ250C7Y1B 50-400
Max.50Hz 415V
Min.50Hz 380V
17.0 19.0 20 — 14.7 0.75 0.7 0.056×4 0.4×4
FCQ125C7VEB×2 RZQ250C7Y1B 50-400 17.4 19.4 20 — 14.7 0.75 0.7 0.120×2 1.0×2
FFQ60BV1B ×4 RZQ250C7Y1B 50-400 18.2 20.2 25 — 14.7 0.75 0.7 0.055×4 0.7×4
FBQ60B7V1 ×4 RZQ250C7Y1B 50-400 19.0 21.0 25 — 14.7 0.75 0.7 0.125×4 0.9×4
FBQ125B7V3B ×2 RZQ250C7Y1B 50-400 18.2 20.2 25 — 14.7 0.75 0.7 0.225×2 1.4×2
FHQ60BUV1B ×4 RZQ250C7Y1B 50-400 17.8 19.8 20 — 14.7 0.75 0.7 0.062×4 0.6×4
FHQ125BUV1B×2 RZQ250C7Y1B 50-400 16.8 18.8 20 — 14.7 0.75 0.7 0.130×2 0.7×2
FUQ125BUV1B×2 RZQ250C7Y1B 50-400 17.6 19.6 20 — 14.7 0.75 0.7 0.090×2 1.1×2
FDQ125B7V3B ×2 RZQ250C7Y1B 50-400 23.8 25.8 32 — 14.7 0.75 0.7 0.500×2 4.2×2
FDQ25OB7V3B RZQ250C7Y1B 50-400 15.4 17.4 20 — 14.7 0.75 0.7 1.000 7.6