Daikin 668811201 General instructions

1.Turnoffpowertotheheatingandcoolingsystembyremovingthefuseorswitchingtheappropriate
circuitbreakeroff.
2.Removecoverofoldthermostat.Thisshouldexposethewires.
3.Labeltheexistingwireswiththeenclosedwirelabelsbeforeremovingwires.
4.Afterlabelingwires,removewiresfromwireterminals.
5.Removeexistingthermostatbasefromwall.
6.Refertothefollowingsectionforinstructionsonhowtoinstallthisthermostat.
To Remove Existing Thermostat
WARNING
ELECTRICAL SHOCK HAZARD – Turn off power at the main service panel by removing the fuse or
switching the appropriate circuit breaker to the OFF position before removing the existing thermostat.
Important Safety Information
• Thisthermostatisfor24VACapplicationsonly;donotuseonvoltagesover30VAC
• Donotshortacrossterminalsofgasvalveorsystemcontroltotestoperation;thiswilldamageyour
thermostatandvoidyourwarranty
• Allwiringmustconformtolocalandnationalelectricalandbuildingcodes
• Donotuseairconditioningwhentheoutdoortemperatureisbelow50degrees;thiscandamage
yourA/Csystemandcausepersonalinjuries
• Usethisthermostatonlyasdescribedinthismanual
WARNING
Always turn off power at the main power supply before installing, cleaning, or removing thermostat.
Congurationswitch
Resetswitch
Left(system)
button
Right(fan)
button
Downbutton
Upbutton
Fieldprogrammingpins
RC/RHJumper
Fanswitch
Parts Diagram
Icon Descriptions
Fanoperationicon
Coolingoperationicon
Heatingoperationicon
Specifications
Electrical rating: • 24VAC(18-30VAC)
 • 1ampmaximumperterminal
 • 3ampmaximumtotalload
Temperature control range: 45°Fto90°F(7°Cto32°C)Accuracy:±1°F(±0.5°C)
System congurations:1-stageheat,1-stagecool,heatpump,gas,oil,electric
Timing: Anti-shortCycle: 4minutes
 BacklightOperation
Terminations:S1,S2,Y,W/O/B,G2,G1,RC,RH,C
Package Contents/Tools Required
Package includes: Daikin 668811101 programmable thermostat and Operation and Application
Guide.
Wiring Diagrams
Hardwired
5-Wire, Single Transformer
WARNING
Be sure exposed portion of wires does not touch other wires.
To Install Thermostat
WARNING
ELECTRICAL SHOCK HAZARD – Turn off power at the main service panel by removing the fuse or
switching the appropriate circuit breaker to the OFF position before removing the existing thermostat.
IMPORTANT: Thermostat installation must conform to local and national building and electrical
codes and ordinances.
 Note:Mount the thermostat about ve feet above the oor. Do not mount the thermostat on an
outside wall, in direct sunlight, behind a door, or in an area affected by a vent or duct.
1. Turnoffpowertotheheatingandcoolingsystembyremovingthefuseorswitchingthe
appropriatecircuitbreakeroff.
2. Toremovecover,pullgentlyattheseamatthetop.
3. Putthermostatbaseagainstthewallwhereyouplantomountit(Besurewireswillfeedthrough
thewireopeninginthebaseofthethermostat).
4. Marktheplacementofthemountingholes.
5. Setthermostatbaseandcoverawayfromworkingarea.
6. Usinga3/16”drillbit,drillholesintheplacesyouhavemarkedformounting.
7. Useahammertotapsuppliedanchorsinmountingholes.
8. Alignthermostatbasewithmountingholesandfeedthecontrolwiresthroughslitinthermal
intrusionbarrierandintowireopening.
9. Usesuppliedscrewstomountthermostatbasetowall.
10.For2transformersystems,removeanddiscardRC/RHjumper.
11.Insertstripped,labeledwiresinmatchingwireterminals.
12.Gentlytugwiretobesureofproperconnection.Doublecheckthateachwireisconnectedtothe
properterminal.
13.Turnonpowertothesystematthemainservicepanel.
14.Congurethermostattomatchthetypeofsystemyouhave.
15.Replacecoveronthermostatbysnappingitinplace.
16.Testthermostatoperationasdescribedin“TestingtheThermostat”.
Configuration Mode
OFF
1. VerifythethermostatisintheOFFmode.
 PresstheSYS(left)buttonuntiloffmodedisplays.
2. Removethecoverofthethermostatbygentlypullingnearoneofthe
cornersatthetopofthethermostat.
Presstheupordownbuttontochangesettingswithineachscreen.
Down
button
Up
button
Toexitcongurationmode,presstheCONFIGswitchfor1second.
Presstherightbuttontoadvancetothenextscreen.
Note:Pressing the left button will return you to the previous screen. Left
button
Right
button
ThecongurationmodeisusedtosettheDaikinthermostattomatchyourheating/coolingsystem.
Thisthermostatfunctionswithheatpump,airconditioning,gas,oilorelectricheatsystems.
Tocongurethethermostat,performthefollowingsteps:
3. PresstheCONFIGbuttonfor1secondwhilethethermostatisinOFF
mode.
S1 S2 Y W
O/B G RC RH C
RESET CONFIG
RC
RH
FP
CONFIG
Hardwired
5 or 6-Wire, Single Transformer
Hardwired
5-Wire, Single Transformer
Configuration Mode Settings
2.Temperature Differential (1°Fto5°F)(0.5°Cto2.5°C)
Setthenumberofdegreesbetweenyour“setpoint”temperatureandyour
“turnon”temperature.
 Presstheupordownbuttontosetdifferentialvalue.
 Presstheright buttontoadvancetothenextscreen.
ThesetupscreensforCongurationModeareasfollows:
1.Temperature Scale (ForC)
ChooseFahrenheitorCelsius.
 Presstheupordownbuttontoselect.
 Pressthe right buttontoadvancetothenextscreen.
3.Deadband (1°F-9°F)(1°C-5°C)
Settheminimumnumberofdegreesbetweenyourheatsetpointandyour
coolsetpointinAutochangeovermode.
 Presstheupordownbuttontosetdeadbandvalue.
 Presstherightbuttontoadvancetothenextscreen.
Choose System
Reversing Valve
Active
Number of Compressors
or Compressor Stages
Type of
Heat
Heat Pump HP O 1
HP b 1
Non-Heat
Pump
Heat Gas
Heat Electric
Presstheupordownbuttontoselect.
Presstherightbuttontoadvancetothenextscreen.
4. System –Setforheatpump,non-heatpump,reversingvalveoperationandnumberof
compressorsinyoursystem.
5. Lockout (0-8°,COOL-HEAT)
Selectthenumberofdegreessettemperaturecanbechangedduring
keypadlockout.COOL-HEATlockoutallowsadjustmentoftheset
temperaturestothemaximumheatsettemperatureselectedinStep6and
minimumcoolsettemperatureselectedinStep7.
 Note:The mode cannot be changed when the thermostat is locked.
 Presstheupordownbuttontoselect.
 Presstherightbuttontoadvancetothenextscreen.
6. Maximum Heat Setpoint(45°Fto90°F)(7°Cto32°C)
 Adjusttocontrolthemaximumheatsettemperatureallowed.
 Presstheupordownbuttontoselect.
 Presstherightbuttontoadvancetothenextscreen.
Daikin P/N (668811201)
Installation, Operation & Application Guide
Version B: 10-15-13
Non-Programmable Electronic Thermostat
• Configurable
• Single-Stage Heat/Cool Systems
• Single-Stage Heat Pump Systems
• Two Speed Fan Control
• Large Display With Backlight
• Selectable Fahrenheit or Celsius
• Compatible with Gas, Oil, or Electric
• SimpleSet™ Field Programming
• Status Indicator Light
• Relay Outputs (minimum voltage drop in thermostat)
• Remote Sensor Compatible
• Ideally Suited for:
– Residential (New Construction/Replacement)
– Light Commercial
1 Heat/1 Cool, Auto Changeover, Fan Speed Control, Hardwire
Remote or Outdoor Sensor Installation (Optional)
1. Removecoverfromremotesensorhousing.RequiredDaikin
RemoteSensorPartNo.667720401
2. Selectanappropriatelocationformountingtheremote
sensor.
3. Mountremotesensorunitusinghardwareprovided.
4. Installtwostrandshieldedwirebetweenremotesensorand
thermostat.Shieldedwiremustbeused.Do notrunremote
sensorwireinconduitwithotherwires.
 • Wire 1shouldrunbetweentheS1terminalonthe
thermostatandtheS1terminalontheremotesensor
 • Wire 2shouldrunbetweentheS2terminalonthethermostatandtheS2terminalontheremotesensor
 • ConnecttheshieldingofthewiretotheS2terminalonthethermostat
5. Congurethethermostattooperatewiththeremotesensor(seeCongurationModesetting10).
 Note:Remote or outdoor sensor reading can be displayed by simultaneously pressing the
Down and SYS buttons.
Remote Sensor

SimpleSetTM Field Programming
Thisfeatureisusedfortransferringthecongurationfromthemastertothetargetthermostat.All
thermostatsforajobcanbemountedandpoweredup.Congureonethermostat.Thiswillbethe
master.Themasterwillbeusedtocopythecongurationtotherestofthethermostats.
Preparing the master to Send:
1. Themastermustbepoweredwith24VAC.
2. VerifythemasterthermostatisinOFFmode.
3. PressSYS(left)buttonuntilOFFmodedisplays.
4. Removecoverofthemasterthermostatbygentlypullingnearoneofthe
cornersatthetopofthethermostat.
5. PresstheupanddownbuttonsandCONFIGswitchsimultaneouslyfor5
seconds.
6. TheOUTscreendisplaysindicatingthemasterthermostatisreadyto
transferdata.
 Note:PresstheupanddownbuttonsandCONFIGswitchsimultaneouslyfor
5secondstoexitfromdatatransfermodeandtoreturnthemasterto
theOFFmode.
7. Turnoffpowertothemasterandremoveitfromthewall.
8. Connectthemastertothetargetusingthe3wireconnector.Attachone
endtotheMaster’sFPpinsandtheotherendtotheTarget’sFPpins.
 Note:Target thermostat must be powered with 24 VAC for eld programming
to occur.
Whentheconnectionhasbeenmadecorrectly,themasterthermostatwillpowerupandthetargetwill
countfrom5downto1.ItwillthendisplaytheLOCKconrmingthedatahasbeensavedinmemory.
Whenalltargetthermostatshavebeencompleted,reinstallthemasterthermostat.
PresstheupanddownbuttonsandtheCONFIGswitchsimultaneouslyfor5secondstoexitfrom
thedatatransfermodeandtoreturnthemasterthermostattotheOFFmode.
OFF
Requires SimpleSetTM Transfer Cable (668817901)
Daikin Training and Development
Now that you have made an investment in modern, efficient Daikin equipment, its care should be a high priority. For
training information on all Daikin HVAC products, please visit us at www.DaikinApplied.com and click on Training,
or call 540-248-9646 and ask for the Training Department.
Warranty
All Daikin equipment is sold pursuant to its standard terms and conditions of sale, including Limited Product
Warranty. Consult your local Daikin Representative for warranty details. Refer to Form 933-430285Y. To find your
local Daikin Representative, go to www.DaikinApplied.com.
Aftermarket Services
To find your local parts office, visit www.DaikinApplied.com or call 800-37PARTS (800-377-2787). To find your
local service office, visit www.DaikinApplied.com or call 800-432-1342. This document contains the most current
product information as of this printing. For the most up-to-date product information, please go to
www.DaikinApplied.com.
Products manufactured in an ISO certified facility.
LIAF014-110-15-13
Lockout Feature
TheDaikinthermostathasabuttonlockoutfeaturesothemodecannotbe
changedandthetemperatureadjustmentislimited.Selecttheappropriate
lockoutfromCongurationModeSettings(Step5)ofthisguide.
ToactivatetheLOCKfeature:
1. SimultaneouslypresstheSYS,FANandUPbuttonsfor10seconds.
2. willdisplayandthelockoutfunctionwillbeenabled.
TodeactivatetheLOCKfeature,repeatsteps1and2above.
Operating Modes
TherearefourpossibleoperatingmodesfortheDaikinthermostat.Off,Cool,Heat,andCool&Heat
modesareaccessedbypressingtheSYS(left)button.Programmodeisaccessedbypressingthe
SYS(left)andFAN(right)buttonssimultaneously.
Cool Mode
 • Inthismode,thethermostatcontrolsthecoolingsystem.Whenthe
coolingoutputs,thesnowakeicon apprearsonthedisplay.
Note:There is a four minute delay for your compressor to restart after
it has turned off.
OFF Mode
 • Inthismode,thethermostatwillnotturnontheheatingorcoolingdevices
Note:The indoor fan can be turned on manually in every operating
mode by pressing the FAN (right) button. The word FAN
shows on the display and the fan icon appears when the fan
operates.
Cool and Heat Mode (Auto Changeover)
 • Inthismode,thethermostatcontrolsthecoolingandheatingsystems,
automaticallychangingoverfromonetotheotherasneeded.
 • Thetimingdisplayalternateswiththesettemperatureevery10seconds
inthecoolandheatmode.
Heat Mode
 • Inthismode,thethermostatcontrolstheheatingsystem.Whentheheat
outputs,theameicon apprearsonthedisplay.
Note:For heat pumps, there is a four minute delay for your
compressor to restart after it has turned off.
Testing the Thermostat
Oncethethermostatiscongured,itshouldbethoroughlytested.
Heat Test
1. PressSYS(left)buttonuntilheatmodeisdisplayed.
2. Adjustthesettemperaturesoitis5degreesabovetheroomtemperature.
3. Heatshouldcomeonwithinafewseconds.RedLEDmayturnon.
4. Adjustthesettemperature2degreesbelowtheroomtemperatureandthe
heatshouldturnoff.Theremaybeafandelayonyoursystem.
 Note: Forheatpumps,thereisafour-minutedelaytoprotectyourcompressorafteritturnsoff.
Tobypassthecompressortimedelay,gotoOFFmodefor5seconds.
Cool Test
1. PressSYS(left)buttonuntilcoolmodeisdisplayed.
2. Adjustsettemperaturesoitis5degreesbelowroomtemperature.
3. A/Cshouldcomeonwithinafewseconds.GreenLEDmayturnON.
4. Adjustthesettemperature2degreesabovetheroomtemperatureand
theA/Cshouldturnoff.Theremaybeafandelayonyoursystem.
 Note: Thereisafour-minutetimedelaytoprotectthecompressorafteritturnsoff.To
bypassthecompressortimedelay,gotoOFFmodefor5seconds.
Fan Test
1. PressFAN(right)button.Fandisplays.IndoorfanturnsON.
2. PressFAN(right)button.IndoorfanturnsOFF.
CAUTION
Donotenergizetheairconditioningsystemwhentheoutdoortemperatureisbelow50degrees.
Itcanresultinequipmentdamageorpersonalinjury.
Mode of Operation
TheDaikinthermostatisanautochangeover,single-stageheat,single-stagecoolthermostat.It
functionswithairconditioning,heatpumps,gas,oilorelectricheatsystems.
Thethermostatactivatestheheatingappliancewhentheroomtemperatureisbelowthesetheat
temperature(bythedifferentialtemperature)andtheredindicatorlight(congurable)onthe
thermostatwilllight.Thethermostatwillstopoutputtingandtheredlightwillturnoffwhenthecallfor
heathasbeensatised.Withheatpumps,thethermostatwillnotletthecompressorcomeonfor4
minutesafteritturnsoff.Thisprotectsyourcompressor.
Whentheroomtemperatureisgreaterthanthesetcooltemperature(bythedifferentialtemperature),
thecoolingdeviceisactivatedandthegreenindicatorlight(congurable)onthethermostatwill
turnon.Thethermostatwillstopoutputtingandthegreenlightwillturnoffwhenthecallforcooling
issatised.Thethermostatwillnotletthecompressorcomeonfor4minutesafteritturnsoff.This
protectsyourcompressor.
Thethermostathasfourpossibleoperatingmodes:OFF,Heat,Cool,andHeat & Coolmode.Inoff
mode,thethermostatwillnotturnonheatingorcoolingdevices.The manual fan can be turned on in
all operating modes using the fan switch and the fan speed can be set in all operating modes using
the fan speed switch.Inheatmode,thethermostatcontrolstheheatingsystem.Inthecoolmode,the
thermostatcontrolsthecoolingsystem.Inheat&coolmode,thethermostatcontrolsboththeheating
andcoolingsystems.Theclockdisplayalternateswiththesettemperaturedisplayforheat&cool
mode.
Thethermostatalsohasabuttonlockoutfeature.Thisenablesthethermostattobesettotheproper
modeandtemperatureandlockedsoitcannotbetamperedwith.
12.Status Indicator Light(Led0or1)
 0=Statusindicatorneveron
 1=Statusindicatoronwithrststage
 Presstheupordownbuttontoselect.
 PresstheCONFIGbuttonfor2secondstoexitconguration.
OFF
11. Cooling Fan Delay Off Time(0,30,60,90seconds)
 Selectthefanpurgetimeforcooling.
 Presstheupordownbuttontoselect.
 Presstherightbuttontoadvancetothenextscreen.
10.Temperature Sensor(1-3)
 1.Onlyon-boardsensordeterminesroomtemperature.
 2.Onlyremotesensordeterminesroomtemperature.
 3.Averagetemperatureofon-boardandremotesensor.
 Presstheupordownbuttontoselect.
 Presstherightbuttontoadvancetothenextscreen.
9. Maximum Cycles Allowed Per Hour(--,2-6)
 --=asmanyasneeded,2-6=maximumcycles/hour
 Presstheupordownbuttontoselect.
 Presstherightbuttontoadvancetothenextscreen.
7. Minimum Cool Setpoint(45°Fto90°F)(7°Cto32°C)
 Adjusttocontroltheminimumcoolsettemperatureallowed.
 Presstheupordownbuttontoselect.
 Presstherightbuttontoadvancetothenextscreen.
8. Room Temperature Offset(+9°Fto-9°F)(+4.5°Cto-4.5°C)
 Adjusttocalibratedisplayedroomtemperaturetomatchactualroom
temperature.
 Note:When not set to 0, will display.
 Presstheupordownbuttontoselect.
 Presstherightbuttontoadvancetothenextscreen.
Troubleshooting
Symptom Remedy
Nodisplay Checkfor24VACatthermostat;displayisblankwhen24
VACisnotpresent
Systemfandoesnotcomeonproperly Verifywiringiscorrect,checkGas/ElectricConguration
(seeSetting)
Allthermostatbuttonsareinoperative Verify24VACispresent;unitlocksoutwhen24VACis
notpresent
Noresponsewithrstbuttonpress Firstbuttonpressactivatesbacklightonly
Thermostatturnsonandofftoo
frequently
Adjusttemperaturedifferential(seeCongurationMode
Setting2)
Fanrunscontinuously PressFAN(right)buttontoturnfanoff
Statusindicatorlightnotonduringcall Turnstatusindicatorfunctionon(seeCongurationMode
Setting12)
Roomtemperatureisnotcorrect Calibratethermostat(seeCongurationModeSetting8)
Ifremotesensorisused,checkS1andS2terminal
connections
displayswhenanybuttonis
pressed
Thermostathasthebuttonlockoutfunctionactivated(see
LockoutFeatureandCongurationModeSetting5)
ondisplayinsteadofroomtemp. CheckforabadconnectionatS1andS2terminals,if
used(seeCongurationModeSetting10)
HeatorCoolnotcomingon Verifywiringiscorrect,verifyRC/RHjumperisinplace
(forsingletransformersystem)
Remoteoroutdoorsensornotaccurate PressSYSandDownbuttonssimultaneouslytodisplay
remoteoroutdoortemperature.VerifyconnectionsatS1
andS2terminals.
Problemnotlistedabove PressResetbuttononce*
* Reset Button Function: Timeanddayarereset,congurationsettingsareunchanged.
FPpins
S1 S2 R C W
O/B GY1W2 W3Y2
RESET CONFIG
FP