Daikin TSTATD2200C-2 Operating instructions

Non-Programmable
Owner's
Manual
and
Installation
Instructions
Digital Thermostat
with Humidity Control • Multi Stage 2+2
TSTATD2200C-2
COMMERCIAL
for
Commercial Use
D_TSTATD2200C-2_Manual_HR.pdf 1 8/29/13 1:11 PM

PAGE I
NOTE: Due to variations in environmental conditions, it is not
always possible to achieve the desired humidification or
dehumidification setpoint.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Follow the Installation Instructions before proceeding.
Set the thermostat mode to “OFF” prior to changing
settings in setup or restoring Factory Defaults.
CAUTION
FOR HOME OR OFFICE USE
Tested to Comply
with FCC Standards
Thermostat TSTATD2200C-2
D_TSTATD2200C-2 _p3.pdf 3 9/6/13 3:30 PM

Glossary of Terms
PAGE II
Auto-Changeover: A mode in which the thermostat will turn on the
heating or cooling based on room temperature demand.
Cool Setpoint: The warmest temperature that the space should rise
to before cooling is turned on (without regard to deadband).
Deadband: The number of degrees the thermostat will wait, once a
setpoint has been reached, before energizing heating or cooling.
Dehumidify: To reduce the amount of moisture in the air.
Differential: The forced temperature difference between the heat set-
point and the cool setpoint.
Heat Setpoint: The coolest temperature that the space should drop
to before heating is turned on (without regard to deadband).
Humidify: To increase the amount of moisture in the air.
Icon: The word or symbol that appears on the thermostat display.
Mode: The current operating condition of the thermostat (i.e. Off,
Heat, Cool, Auto, Program On).
Non-Programmable Thermostat: A thermostat that does not have
the capability of running Time Period Programming.
Temperature Swing: Same as Deadband.
D_TSTATD2200C-2_Manual_HR.pdf 5 8/29/13 1:11 PM

Table of Contents
PAGE III
5
1
17
18
21
22
23
15
Quick Start
Get to Know Your Thermostat
USER SETUP
Thermostat Display Options
Humidification & Dehumidification
Locking and Unlocking the Keypad
24
Factory Defaults
Dry Contact Operation
INSTALLER SETUP
16
Scrolling Display Options
System Runtimes
Advanced Setup
TECHNICIAN SETUP
29
Advanced Output Testing
Equipment Testing
19
Backlight Operation
25
26
Troubleshooting
Sensor Calibration 25
25
INDEX
16
Emergency Heat
27
Advanced Setup Table
7
INSTALLATION INSTRUCTIONS
Sample Wiring Diagrams 11
Test Operation 14
Setpoint Limits 19
20
Remote Sensor Operation
D_TSTATD2200C-2_Manual_HR.pdf 7 8/29/13 1:11 PM

OVERRIDE
OUTDOOR
HUMIDITY MODE
OVERRIDE
Outdoor
COOL
79
77
80
AUTOON
FAN
RST FLTR
EMERGCY
HEAT DISPLAY ACCESSORY SETUPSERVICE
RST FILTER
EMERGCY
HEAT DISPLAY ACCESSORY SETUPSERVICE
OVERRIDE
HUMIDITY MODE
OVERRIDE
Outdoor
C OO L
79
77
80
RUNOFF
PROGRAM
HOLD TO SET
RST FLTR
EMERGCY
HEAT DISPLAY ACCESSORY SETUPSERVICE
SET CLOCK
EMERGCY
HEAT DISPLAY ACCESSORY SETUPHOLIDAY
PAGE 1
Get to Know Your Thermostat
Down
Button Override Button Up
Button
Heat or Cool
Demand Indicator
Red = Heat
Green = Cool
Backlit LCD Display Front Panel
Scrolling Display
Emergency
Heat Service Accessory
Humidity
Outdoor Temp.
Mode
Display
Options
Setup
Reset
Filter
Fan
On | Auto
Hidden
Buttons
D_TSTATD2200C-2_Manual_HR.pdf 9 8/29/13 1:11 PM

PAGE 2
Mode Indicators
Selects the operational mode of the equipment.
HEAT - Indicates the heating mode.
COOL - Indicates the air conditioning mode.
HEAT & COOL - Indicates the system will automatically change-
over between heat and cool modes as the temperature varies.
OFF - Indicates heating and cooling is turned off.
RoomTemperature Display
Indicates the current room temperature and displays the outdoor
temperature when selected.
The scrolling display will be used to help you easily navigate the setup
screens in the thermostat.
Get to Know Your Thermostat
Outdoor icon
Indicates the temperature displayed is from the optional outdoor
sensor.
Outdoor
Fan On
AUXHEAT
Setup Step
2nd
Stage
COOL
88
88
Lo
88
H
88
Display Features
D_TSTATD2200C-2_Manual_HR.pdf 10 8/29/13 1:11 PM

Outdoor
Fan On
AUXHEAT
Setup Step
2nd
Stage
COOL
88
88
Lo
88
H
88
PAGE 3
Desired SetTemperature
Indicates desired room temperature(s).
Setup Step icon
Indicates the step number when the thermostat is in the
setup mode.
icon
Indicates the keypad has been locked.
2nd Stage icon
Indicates what stage of cooling or heating is currently energized.
Get to Know Your Thermostat
Display Features
6
6
D_TSTATD2200C-2_Manual_HR.pdf 11 8/29/13 1:11 PM

AuxHeat icon
Indicates 2nd stage electric strip heat is being used when the
thermostat is programmed for Heat Pump operation.
Fan On icon
Indicates constant, continuous fan operation.
When Fan On is not lit - indicates the fan will only operate when
necessary to heat or to cool.
PAGE 4
Get to Know Your Thermostat
Display Features
Outdoor
Fan On
AUXHEAT
Setup Step
2nd
Stage
COOL
88
88
Lo
88
H
88
10
10
D_TSTATD2200C-2_Manual_HR.pdf 12 8/29/13 1:11 PM

PAGE 5
Press the UP or DOWN buttons to modify the selection.
Quick Start
Press the MODE button to advance and confirm through the setup steps.
During Setup and Programming:
Selecting the Heat or Cool Mode
Select mode by pressing the MODE button.
Heating Only - The HEAT setting indicates the temperature the room has to reach
before the furnace will turn on to heat the room.
Cooling Only - The COOL setting indicates the temperature the room has to reach
before the air conditioner will turn on to cool the room.
Heating or Cooling (Auto-Changeover) - AUTO will automatically select heat or cool
based on room temperature demand.
OFF - OFF indicates both heating and air conditioning systems are turned off.
Selecting Your Desired Temperature
AUTO-CHANGEOVER MODE - Pressing the UP or DOWN buttons in Auto mode
will adjust both the heat and cool setpoints simultaneously. To adjust heat and cool
setpoints individually, choose HEAT mode to adjust the heat setpoint and COOL
mode to adjust the cool setpoint, then return to AUTO mode.
HEAT OR COOL MODE - Pressing the UP or DOWN buttons in Heat or
Cool mode will adjust only the heat or cool setpoints individually displayed.
NOTE - This thermostat has a fixed two degree deadband. With a Cool setpoint of
72 degrees Fahrenheit, cooling will energize at a room temperature of 74 degrees.
With a Heat setpoint of 68 degrees Fahrenheit, heating will energize at 66 degrees.
Using the Reset Filter Button
Reset Filter - Press the RST FILTER button to view the current filter
runtime. Press the OUTDOOR button to reset the filter runtime counter
to 0. Press the RST FILTER button again to return to normal operation.
D_TSTATD2200C-2_Manual_HR.pdf 13 8/29/13 1:11 PM

Quick Start
Using the Override Button
Unoccupied Operation - During a Dry Contact forced unoccupied period pressing the
OVERRIDE button will force the thermostat into the mode it was in before the Dry
Contact forced it into the Unoccupied mode. For example: if the thermostat was in the
Auto mode and the Dry Contact forced it into Unoccupied mode, pressing OVERRIDE
will force the thermostat back into the Auto mode. The remaining override time will be
displayed in the upper left corner of the display. Each press of the OVERRIDE button
will add another 30 minutes of time for up to 4 hours. If the maximum time has been
set, the next press of the OVERRIDE button will reset the timer and return the
thermostat to the Unoccupied mode.
NOTE: Override may only be
used when the Dry Contact
has forced the thermostat
into the Unoccupied mode.
PAGE 6
OUTDOOR TEMP - Press the OUTDOOR button to view the current
outdoor temperature. Pressing the OUTDOOR button again to return
to normal operation.
REMOTE TEMP - Press the ACCESSORY button to enter the accessory
setup screen. Press the UP button to view linked wireless and wired
sensors and other accessories. Press the ACCESSORY button to
return to the main screen.
Note: If no outdoor sensor is connected, 2 dashes [- -] will appear with
the first button press.
Viewing and Setting the Indoor Humidity Sensor
Press the HUMIDITY button to display the current humidity measured at
the thermostat. The room relative humidity is displayed in the top left corner.
The humidification setpoint appears in the larger center display and can be
adjusted using the UP or DOWN buttons. Press the MODE button to view and
adjust the dehumidification setpoints. Press the HUMIDITY button again to
confirm settings and return to normal operation.
Note: Due to variations in environmental conditions, it is not always
possible to achieve the desired humidification or dehumidification
setpoint.
IMPORTANT: Allow at least 2 minutes after the thermostat
is powered on for the humidity to read correctly.
Viewing the Outdoor and Remote Temperature Sensors
D_TSTATD2200C-2_Manual_HR.pdf 14 8/29/13 1:11 PM

PAGE 7
Assemble tools: Flat blade screwdriver, wire cutters and wire
strippers.
Carefully unpack the thermostat. Save the screws, any
brackets, and instructions.
Make sure your Heater/Air Conditioner is working properly
before beginning installation of the thermostat.
Turn off the power to the Heating/Air Conditioning system at
the main fuse panel. Most residential systems have a separate
breaker for disconnecting power to the furnace.
To install the thermostat properly, please follow these step by
step instructions. If you are unsure about any of these steps,
call a qualified technician for assistance.
Remove the cover of the old thermostat. If it does not come off
easily, check for screws.
Loosen the screws holding the thermostat base or subbase to the
wall and lift away.
Keep the old thermostat for reference purposes, until your new
thermostat is functioning properly.
Disconnect the wires from the old thermostat. Tape the ends
of the wires as you disconnect them, and mark them with the
letter of the terminal for easy reconnection to the new thermo-
stat.
Remove & Replace the Old Thermostat
Installation Instructions
D_TSTATD2200C-2_Manual_HR.pdf 15 8/29/13 1:11 PM

PAGE 8
Wire Connections
* O/B is used if your system is a Heat Pump.
Wire from the
old thermostat
terminal marked
Function
Install on the
new thermostat
connector marked
G or F Fan G
Y1, Y or C Cooling Y1
W1, W or H Heating W1/O/B
PowerRh, R, M, Vr, A R
C
O/B
C
Common
Rev. Valve
W2 2nd Stage Heat
Y2 Y2
H, HUM HUM
CKGND
Ck1
Dry Contact Switch
Dry Contact Switch DRY CONTACT
DRY CONTACT
W1/O/B*
W2
D, DEHUM DEHUM
2nd Stage Cooling
Humidity
Dehumidity
Wire Connections
Installation Instructions
If the terminal designations on your old thermostat
do not match those on the new thermostat, refer
to the chart below or the wiring diagrams
that follow.
REMOTE/
OUTDOOR
REMOTE/
OUTDOOR
S1, OUT -
S2, OUT +
Remote/Outdoor
Sensor
Remote/Outdoor
Sensor
D_TSTATD2200C-2_Manual_HR.pdf 16 8/29/13 1:11 PM

PAGE 9
IMPORTANT: This thermostat requires both
R (24 VAC Return) and C (24 VAC Common) be
connected to the backplate terminals.
Installation Instructions
The TSTATD2200C-2 Thermostat Backplate
R C DEHUM HUM W2 W1/O/B G Y1 Y2
REMOTE/
OUTDOOR
DRY
CONTACT
1st stage heat/reversing valve
2nd stage heat circuit
Dehumidifier control circuit
Humidifier control circuit
W2
DEHUM
C
W1/O/B
HUM
R
REMOTE/
OUTDOOR
Y2
Y1
DRY
CONTACT
24 VAC common
24 VAC Return
Remote/Outdoor
sensor connections
Dry Contact
connections
2nd stage compressor
G
1st stage compressor
Fan relay
D_TSTATD2200C-2_Manual_HR.pdf 17 8/29/13 1:11 PM

PAGE 10
This jumper configures the thermostat to control a conventional
gas/electric system or a heat pump. If your system is anything
other than a heat pump, leave this jumper set for GAS/ELEC.*
GAS/ELEC
HEATPUMP
GAS/ELEC
HEATPUMP
OR
J1
When J1 is configured to control a heat pump, this jumper (J2)
must be set to control the appropriate reversing valve. If RV=O
is chosen, the W1/O/B terminal will energize in cooling. If RV=B
is chosen, the W1/O/B terminal will energize in heating.
When J1 is set for GAS/ELEC:
This jumper (J3) controls h
ow the thermostat will control the
Fan (G) terminal in heating mode. When GAS is chosen, the
thermostat will not energize the Fan (G) terminal in heating.
When ELEC is chosen the thermostat will energize the fan in
heating.
OR
J2
OR
J3
RV=O
RV=B
RV=O
RV=B
GAS
ELEC
(FAN)
GAS
ELEC
(FAN)
*For some commercial heat pumps, this jumper will need to
be set for GAS/ELEC. Consult the commercial heat pump literature.
Installation Instructions
GAS
ELEC
GAS/ELEC
HEATPUMP
RV=O
RV=B
J1J2J3
Explanation of Thermostat Jumpers
Jumpers are located on the back of the thermostat
RV=O
RV=B
J2
GAS/ELEC
HEATPUMP
J1
GAS
ELEC
J3
D_TSTATD2200C-2_Manual_HR.pdf 18 8/29/13 1:11 PM

PAGE 11
Residential & Commercial 1 Stage Heating
with no Fan.
3 Wire, Heat Only
24VAC Power
24VAC Common
1st Stage Heat
Gas/Elec
O (not used)
Gas
Residential & Commercial 1 Stage Cooling.
4 Wire, Cool Only
R
C
Y1
G
J1 =
J2 =
J3 =
Installation Instructions
Conventional Heating and Cooling Systems
Residential & Commercial 1 Stage Cooling,
with 1 stage Gas Heat.
5 Wire, 1 Stage Cooling, 1 Stage Heat
24VAC Power
24VAC Common
1st Stage Heat
1st Stage Cool
Fan
Gas/Elec
O (not used)
Gas
Residential & Commercial 1 Stage Cooling,
with 1 stage Electric Heat.
5 Wire, 1 Stage Cooling, 1 Stage Heat
24VAC Power
24VAC Common
1st Stage Heat
1st Stage Cool
Fan
Gas/Elec
O (not used)
Electric
Residential & Commercial 2 Stage Cooling,
with 2 stage Gas Heat.
7 Wire, 2 Stage Cooling, 2 Stage Heat
24VAC Power
24VAC Common
1st Stage Heat
2nd Stage Heat
1st Stage Cool
2nd Stage Cool
Fan
Gas/Elec
O (not used)
Gas
Sample Wiring Diagrams
R
C
W1/O/B
Y1
G
J1 =
J2 =
J3 =
R
C
W1/O/B
Y1
G
J1 =
J2 =
J3 =
R
C
W1/O/B
W2
Y1
Y2
G
J1 =
J2 =
J3 =
R
C
W1/O/B
J1 =
J2 =
J3 =
24VAC Power
24VAC Common
1st Stage Cool
Fan
Gas/Elec
O (not used)
Gas
D_TSTATD2200C-2_Manual_HR.pdf 19 8/29/13 1:11 PM

PAGE 12
Installation Instructions
Residential & Commercial Heat Pump with
‘O’ Reversing Valve
5 Wire, 1 Stage Cooling, 1 Stage Heat
R 24VAC Power
C 24VAC Common
W1/O/B Reversing Valve
Y1 1st Stage Compressor
(Cool or Heat)
G Fan
J1 = Heat Pump
J2 = O
J3 = Gas
Residential & Commercial Heat Pump with
‘O’ Reversing Valve
6 Wire, 1 Stage Cooling, 2 Stage Heat
R 24VAC Power
C 24VAC Common
W1/O/B Reversing Valve
Y1 1st Stage Compressor
(Cool or Heat)
W2 Aux Heat
G Fan
J1 = Heat Pump
J2 = O
J3 = Electric
Residential & Commercial Heat Pump with
‘O’ Reversing Valve.
7 Wire, 2 Stage Cooling, 2 Stage Heat
R 24VAC Power
C 24VAC Common
W1/O/B Reversing Valve
Y1 1st Stage Compressor
(Cool or Heat)
Y2 2nd Stage Compressor
(Cool or Heat)
G Fan
J1 = Heat Pump
J2 = O
J3 = Electric
Setup Step 26 is set to 2
(Number of Compressor Stages)
Sample Wiring Diagrams
Heat Pump Systems
D_TSTATD2200C-2_Manual_HR.pdf 20 8/29/13 1:11 PM

PAGE 13
Installation Instructions
Sample Wiring Diagrams
Humidification or Dehumidification
Humidification
System
DEHUM/
HUM
Dehumidification Terminal
on Equipment
Dry Contact and Remote or Outdoor Sensor
12
11
10
9
8
765
4
3
2
1
Time Clock
R C DEHUM HUM W2 W1/O/B G Y1 Y2
REMOTE/
OUTDOOR
DRY
CONTACT
R C DEHUM HUM W2 W1/O/B G Y1 Y2
REMOTE/
OUTDOOR
DRY
CONTACT
10K Thermistor
Remote or Outdoor Sensor
TSTATGAC-WS or TSTATGTAC-OS
D_TSTATD2200C-2_Manual_HR.pdf 21 8/29/13 1:11 PM

PAGE 14
Test Operation
Press MODE to view the version numbers of the thermostat.
Installation Instructions:
To enter Technician Setup, press and hold the SETUP button for 5 seconds until
all the icons appear. Follow the next steps to view settings and test equipment.
Press MODE again to view the jumper settings and current state of
the Dry Contact terminals.
Press MODE again and the scrolling display will read “TURN ON
EQUIPMENT?” Press UP forYes or DOWN for No.
This thermostat has a diagnostic feature that enables testing of all
outputs. This feature is contained in Technician Setup.
IfYes is chosen, press UP to turn on heat or DOWN to turn on
Cooling. The scrolling display will read “NOTHING ON.” Next:
Press UP to turn on and cycle up through the heating stages.
Press DOWN to turn the heating stages off. Press MODE to exit.
Press DOWN to turn on and cycle down through the cooling stages.
Press UP to turn the cooling stages off. Press MODE to exit.
1.
2.
3.
Press MODE until “CALIBRATE SENSORS?” appears on the scroll-
ing display. Press UP forYes or DOWN for No. Press MODE to
select which sensor to calibrate. Use UP or DOWN to modify your
selection.
4.
Press MODE until “CONTROL HUM?” appears on the scrolling dis-
play. Press UP for On or DOWN for Off. Press MODE to continue.
5.
Press MODE until “CONTROL DEHUM?” appears on the scrolling
display. Press UP for On or DOWN for Off. Press MODE to
continue.
6.
To exit Technician Setup at any time, press the SETUP button. Technician Setup
will automatically exit after 10 minutes if no buttons are pressed.
D_TSTATD2200C-2_Manual_HR.pdf 22 8/29/13 1:11 PM

PAGE 15
User Setup:
Press the SETUP button, then press MODE repeatedly until the Backlight setup
step appears. Use the UP or DOWN buttons to make selection. Press MODE to
advance to the next step. Press SETUP to leave the setup screens.
Backlight (Setup Step 3)
Backlight Level (Setup Step 4)
Backlight Off - Backlight turns on with any button press and turns off after 8 seconds.
Backlight On - Backlight is on continuously.
The backlight can be adjusted between always off and seven levels of brightness.
Backlight Operation
The thermostat backlight may be set to be always on, on temporarily with any button
press, on throughout the evening, or always off. (For always off, see Backlight Level)
Press the SETUP button, then press MODE repeatedly until the Backlight setup
step appears. Use the UP or DOWN buttons to adjust the brightness.
Press MODE to advance to the next step. Press SETUP to leave the setup
screens.
Language (Setup Step 18)
Setup step instructions on the scrolling display can be set for English, Spanish, or French.
Press the SETUP button, then press MODE repeatedly until the Language setup
step appears. Use the UP or DOWN buttons to make selection. Press MODE to
advance to the next step. Press SETUP to leave the setup screens.
To enter Advanced Setup, press the SETUP button, then press MODE. Use the
UP or DOWN buttons to adjust the value of your selection. Press MODE to
advance to the next setup step. Press SETUP again to leave the setup
screens.
How to Change Settings in the Setup Screens
D_TSTATD2200C-2_Manual_HR.pdf 23 8/29/13 1:11 PM

PAGE 16
Scrolling Screen and Display Options
User Setup:
Scrolling Display Method (Setup Step 19)
This option allows the user to choose how the scrolling text is displayed. Options are:
Press the SETUP button, then press MODE repeatedly until the Scrolling Method
setup step appears. Use the UP or DOWN buttons to make a selection.
Press MODE to advance to the next step. Press SETUP to leave the setup
screens.
Outdoor
C OO L S ET
H EAT S ET
78 74
68
85
A
Outdoor
C OO L S ET
H EAT S ET
78 74
68
85
B
Example of “Whole Words Centered”:
Any removed icons will be displayed temporarily when a setting change is made.
Scroll Letters Slow
Scroll Letters Fast
Scroll Words Slow
Scroll Words Fast
Scrolling Non-Scrolling
Whole Words Slow
Whole Words Fast
Words Centered Slow
Words Centered Fast
Display
This option allows the user to “de-clutter” the thermostat display screen by removing
icons from the main display. The room temperature will always be shown. Service
information may also be viewed by pressing and holding the DISPLAY button.
Each press of the DISPLAY button
will remove icons. Keep pressing
DISPLAY to make icons reappear.
Press and hold DISPLAY for 5 seconds
to view a name and phone number to
call for service.
Show All
Remove ScrollingText
Remove OutdoorTemp
Remove Setpoint
Remove Mode
D_TSTATD2200C-2_Manual_HR.pdf 24 8/29/13 1:11 PM