Daintree GE Current WA100-PM User manual

(WA100-PM)
Daintree®
Wireless Adapter
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Save these instructions for future use.
1Installation Process
Installation Guide
WA100-PM |DT113
1. Disconnect power before installation. Turn off all power
 toaffectedlightxturesbyturningoffcircuitbreakers. 
 Conrmthatpowerisoffatalllightxturesbefore
continuing installation.
2. Set the WA100-PM DIP switches to support the device(s)
 beingconnectedtoit.SeeDIP Switch Settings (page 2).
3. IMPORTANT: Afxthesmalllabelwith4-5digitsofthe
 WA100-PM’sIEEEaddressontheoorPlantoindicate
its location.
4. Mount the WA100-PM in the driver cavity of the light
 xture,orexternaltothelightxture,ortoajunctionbox
approved for the application. See Mounting (page 12).
5. Connect low voltage wiring from the WA100-PM to the
 driver,switch(es)and/orsensorsasappropriateforyour
application. See Wiring (pages 3-11). Cap any unused wires.
Risk of electrical shock.Disconnectpowerbeforeservicingor
installing product.
Install in accordance with National Electric Code and local codes.
WARNING
Risk of injury. Wear safety glasses and gloves during installation and
servicing.
CAUTION
The Daintree WA100-PM Wireless Adapter forms part of the
DaintreeNetworkedwirelesscontrolssolutionforsmart
commercialandindustrialbuildings.Ittransmitsandreceives
messages over the wireless ZigBee®networkandcontrolslights.
TheWA100-PMisanACpowereddevicethatprovidesOn/Off
switching as well as 0-10V analog dimming control for
LEDdriversandballasts.*Italsoprovidespowerforlowvoltage
occupancysensors,photosensors(daylightharvesters),
wallswitches,andcontrolsignalswhileitprovidesthewireless
adaptationthatenablesthemtocommunicatewiththe
rest of the wireless control solution. The control signals to and
fromtheseconnecteddevicespassbetweentheWA100-PM
and the Wireless Area Controller in Daintree Controls Software
(DCS)webapplication.
Error/Test — On when the Wireless Adapter is in an error state.
Flashes to indicate unit Reset and during Installation Test Mode (red).
Joined —OnwhentheWirelessAdapterhasjoinedaZigBee
®
network.
Flashes to indicate Reset and during sensor Installation Test Mode (green).
Power — On when power is applied to the Wireless Adapter (green).
LED Indicators
6. Connect line voltage wires from the supply circuit to the
WA100-PM and to the driver as shown in Wiring. Cap any
unused wire.
7.Checkloadcircuitsthenturnonthecircuitbreakerstopower 
up the WA100-PM. The light connected to the WA100-PM turns
On when power is initially applied (and when power is restored
after a power failure).
8. Ensure the WA100-PM green Power LED is On.
9.PressandholdtheblueRESETbuttonontheWA100-PMfor
 3secondstoresettheunit.Releasethebuttonwhenthegreen
 JoinedLEDandtheredErrorLEDsbeginashing.
10. Perform the installation test appropriate for your application.
See Installation Tests(pages13-14)
Power
LED
Reset
Button
Joined
LED
Error
LED

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
2
2
4
3
WA100-PM Model Variants
DIP Switch Mode descriptions
DIP Switch settings
ThemodelnumberWA100wastheoriginalversionofthe
adapter and is no longer sold. The WA100-PM model monitors
and measures the power consumption of the connected lighting
load. The WA100-PM reports power measurement data to DCS.
Figure 1: DIP switch location
Figure 2: DIP Switch Table — See DIP switch Mode
descriptions for information about each option.
DIPswitchsettingsenabletheWA100-PMtooperatea
ppropriately for the type of lighting control it provides and
the type of device(s) to which it is connected and adapting
forwirelesscommunication.SetDIPswitchesbasedonlyon
the devices that are physically wired to the WA100-PM.
There are two primary adaptation modes to choose from as
determinedbytheDIPswitch1setting.
• InLightAdapterMode,thesettingsareforthetype
 oflightingcontrolthatisavailableontheconnected
 driver,and/orthesensortype(s)connectedtothe
WA100-PM.
• IntheSwitchAdapterMode,settingsareforthe
connected switch type and whether the WA100-PM
is connected to a light.
CongureDIPswitchsettingsonlyasshowninthisinstruction.
Incorrect switch settings will cause unexpected operation.
AfteryouchangeDIPswitchsettings,youneedtopresstheblue
Resetbuttonfor3secondstoresettheunit.Releasethebutton
whenthegreenJoinedandredErrorLEDsbeginashing.
Light Adapter Mode
Control Type
On/Off + 0-10V dimming: providesOn/Offcontrolusingitsline
voltage Switched Load connection to the driver(s). It also provides
0-10V dimming control to the driver(s).
On/Off (no dimming): providesOn/Offcontrolusingitsline
voltageSwitchedLoadconnection,anditslowvoltagedigital
outputtoanexternalrelay.Note,bothoutputsareswitchedat
the same time in this driver control mode.
Alternate:providesOn/Offswitchingforonedriverloadusingits
linevoltageSwitchedLoadconnection,anditslowvoltagedigital
outputtoanexternalrelaytoswitchaseconddriverload.This
allowslightinglevelcontrolfornoload(0%),oneortheotherof
thetwoloads,andbothloads(100%).SeeFigure13.
Bi-Level:providesOn/Offswitchingforonedriverwithtwoloads
using its line voltage Switched Load connection and low voltage
digitaloutputanexternalrelaytoswitchthesecondload.This
allowslightingleveltocontrolfornoload(0%),partialload
(accordingtodrivercapability)orfullload(100%).SeeFigure12.
No Driver (sensors only): provides wireless adaptation to
connectedoccupancysensorand/orphotosensoronly.No
driver control.
Sensor
Toprovidewirelessadaptationforsensors,setDIPswitches1,5&
6 according to the type(s) of sensors connected to the WA100-PM.
Range Extender
TheWA100-PMjoinstheZigBeenetworkandactsonlyasa
wirelessrepeatertoimprovethewirelessrangeand/orreliability.
No lights or devices are connected to the WA100-PM.
Occupancy
Photosensor
Both
None
Range Extender*
nolight,nosensor
*Validonlywithrmwarev2.6orhigher
On/Off+0-10Vdimming
On/Off(nodimming)
Alternate Switching
Bi-Level
No Driver (sensors only)
SensorSwitches5&6Mode DriverTypeSwitches1to4
DIP Switch Positions
Light Adapter
OFF
ON
Light + Switch
(driver&switch
are same type)
No Light
(switch only)
Dimming
On/Off(nodimming)
Alternate Switch
Bi-Level
Light OutputSwitches5&6Mode Switch TypeSwitches1to4
Switch Adapter
Figure 2: DIP Switch Table — See DIP switch Mode
descriptions for information about each option.

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
3
5
6
7
Switch Adapter Mode
Occupancy Sensor Time Delays
Wiring
Switch Type
Dimming: operating the connected switch generates
dimmingandOn/Offsignals.
On/Off (no dimming): operating the connected switch
generatesOn/Offsignals.
Alternate: operating the connected switch will switch separate
drivers,providingnoload(0%),partialload(oneortheotherof
thetwoloads,accordingtothedriverloading)orfullload(100%).
Bi-Level: operating the connected switch will switch loads
independentlyinabi-leveldriver(or2drivers),providingno
load(0%),partialload(accordingtothedrivercapabilityor
driver loading) or full load (100%).
Light output ID
Light + Switch (driver and switch are the same type): the
connecteddrivermatchestheoperationalcapabilityofthe
switch.Forexample:
 •IftheSwitchtypeis“Dimming,”adimmingswitchand0-10V
  dimmabledriverarebothconnectedtotheWA100-PM.
See Figure 10.
 •IftheSwitchtypeis“On/Off(nodimming)”anOn/Offswitch
  isconnectedtotheWA100-PMdigitalinputandOn/Off 
driver(s) are connected to the WA100-PM’s line voltage
  SwitchedLoadconnectionand/oranexternalrelay
connected to the WA100-PM’s low voltage digital output.
 •IftheSwitchtypeis“Bi-Level,”abi-leveldriverandbi-level 
switch connect to the WA100-PM.
No Light (switch only): provides wireless adaptation for the
selected switch type only. No light is connected to the WA100-PM.
Occupancysensortimedelaysmustbesetforminimum.
WhentheDaintreeNetworkediscommissioned,timedelays
aresetintheDaintreeControlsSoftware(DCS)webapplication.
TheseDCS“Offdelays”startcountingdownafterthesensor’s
internaltimedelayexpires.Therefore,setoccupancysensorsfor
the minimum time delay during the WA100-PM installation.
Line voltage wiring connects to the electrical supply circuit and
tothedriver(s).TheBlack(Hot)yingleadandtheRed(Switched
Load)yingleadare14AWG.TheWhite(Neutral)yingleadis
18AWG.
Lowvoltage22AWGyingleadsprovideforconnectionsto
supply low voltage power and carry control signals to and
fromlowvoltagedevicessuchasswitches,dimmers,photocells,
isolated relays and 0-10V analog dimming driver controls. Do
not connect any single low voltage device to more than one
WA100-PM.
While the WA100-PM is in Installation Test mode the low voltage
devices connected to the WA100-PM directly control the lights
wiredtothesameWA100-PM.AfteryouexitInstallationTest
mode,thelightsturnOnandareNOTcontrolledbythedevices
connected to the WA100-PM.
Afterjoiningthewirelessnetwork,thecontrolsignalsfromthe
low voltage devices pass through the WA100-PM and are sent
wirelesslytotheDaintreeNetworked.Dependingonthezone
anddevicecongurationintheDCS,wirelesssignalsfromthe
WAC to the WA100-PM determine the operation of the light(s).
Design Caution
Wirelessadaptersmustalwaysbeprovidedwithuninterrupted
power. Do not install a wireless adapter such as the WA100-PM to
control an electrical circuit that provides power to other wireless
devices or adapters. If power to wireless adapters or devicesis shut
off,controlandcommunicationwiththemisdisabled.
Risk of electrical shock. Disconnectallpowerbeforeinstallationand
duringservicing.DonotopenWA100-PMenclosure;nouser-serviceable
parts inside. All installation and maintenance of line voltage equipment
mustbeperformedbyaqualiedelectrician.TheWA100-PMmustbe
installedinaccordancewithalllocal,state,andnationalelectricalcodes
andrequirements.Wiringconnectorsarenotsupplied.ULrecognized
wiringconnectorsmustbeusedintheinstallation.
CAUTION
Reducing noise on low voltage (0-10V) wiring
• Keep wiring as short as practical
• Keep signal lines separate from mains voltage lines.
• Reducetheareacreatedbythesignallinesand 
 theGNDreturn(i.e.,keepthemclosetogether).
• IfpossibletwistthesignallinewiththeGNDreturn.

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
4
Figure 3: Wiring Identication
Figure 4: Dimming Light Fixtures
7Wiring Continued
Perform Installation Test Suite 1
DIP Switches
DriverType:
On/Off+0-10V
dimming
WiredSensor:
None
On 1 2 3 4 5 6
(ALL OFF)
OFF
ON

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
5
Figure 5: On/Off (non-dimming) Light Fixtures
ThiscongurationallowstheWA100-PMtoprovideautomatic
On/Offswitchingoflightxtures.
Figure 6: On/Off (non-dimming) Light Fixture(s), Occupancy
Sensor conguration
ThiscongurationallowstheWA100-PMtoprovideautomatic
On/Offswitchingbasedonoccupancy.Setoccupancysensor
for minimum time delay.
7Wiring Continued
Perform Installation Test Suite 1
DIP Switches
DriverType:
On/Off+0-10V
dimming
WiredSensor:
None
On 1 2 3 4 5 6
(#4 ON)
Perform Installation Test Suite 2
DIP Switches
DriverType:
On/Off
(no dimming)
WiredSensor:
Occupancy
On 1 2 3 4 5 6
(#4, 5 ON)
OFF
ON
OFF
ON

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
6
Figure 7: Dimming Driver(s), Occupancy Sensor conguration
ThiscongurationallowstheWA100-PMtoprovideautomatic
0-10VdimmingcontrolandtoswitchdriversOn/Offbasedon
occupancy. Set occupancy sensor for minimum time delay.
Figure 8: Dimming Light Fixture(s), Photosensor conguration
ThiscongurationallowstheWA100-PMtoprovideautomatic
0-10VdimmingcontrolandtoswitchlightxturesOn/Off.
7Wiring Continued
OFF
ON
Perform Installation Test Suite 2
DIP Switches
DriverType:
On/Off
dimming
WiredSensor:
Occupancy
On 1 2 3 4 5 6
(#5 ON)
OFF
ON
Perform Installation Test Suite 8
DIP Switches
DriverType:
On/Off
dimming
WiredSensor:
Photosensor
On 1 2 3 4 5 6
(#6 ON)

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
7
Figure 9: Dimming Light Fixture(s), Photosensor, Occupancy
Sensor conguration
ThiscongurationallowstheWA100-PMtoprovideautomatic
0-10VdimmingcontrolandtoswitchdriversOn/Off.Set
occupancy sensor for minimum time delay.
Figure 10: Dimming Light Fixture(s) and Switch conguration
ThiscongurationallowstheWA100-PMtoprovide0-10Vdimming
controlandtoswitchlightxturesOn/Off.Italsoprovidesmanual
On/Offcontrolthroughalowvoltagemomentarycontactswitch.
7Wiring Continued
OFF
ON
Perform Installation Test Suite 4
DIP Switches
DriverType:
On/Off
dimming
WiredSensor:
Photosensor
On 1 2 3 4 5 6
(#5,6 ON)
OFF
ON
Perform Installation Test Suite 1
DIP Switches
Wired
SwitchType:
dimming
LightOutput::
Driver same as
switch
On 1 2 3 4 5 6
(#1,5 ON)

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
8
Figure 11: Bi-level Switching
ThiscongurationallowstheWA100-PMtoswitchloads
independentlyinabi-leveldriver(or2drivers),providingno
load(0%),partialload(accordingtothedriver/ballast
capability)orfullload(100%).
Figure 12: Alternate Switching
ThiscongurationallowstheWA100-PMtoalternateinswitching
separatedrivers,providingnoload(0%),partialload(accordingto
the driver loading) or full load (100%).
Always connect the smaller proportion of the total load to the
WA100-PM’s RED Switched Load wire.
7Wiring Continued
OFF
ON
Perform Installation Test Suite 1
DIP Switches
Driver:
Bi-Level
WiredSensor:
None
On 1 2 3 4 5 6
(#3,4 ON)
OFF
ON
Perform Installation Test Suite 1
DIP Switches
Driver:
Alternate
Switching
WiredSensor:
None
On 1 2 3 4 5 6
(#3 ON)

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
9
Figure 13: Switching a Branch Circuit
ThiscongurationallowstheWA100-PMtoprovideOn/Off
switchingofabranchcircuit.
Figure 14: 208V 2-Pole (Phase-to-Phase) wiring
ThiscongurationallowstheWA100-PMtoprovideOn/Off
switchingofabranchcircuit.
7Wiring Continued
OFF
ON
OFF
ON
Perform Installation Test Suite 1
DIP Switches
DriverType:
On/Off
(no dimming)
WiredSensor:
None
On 1 2 3 4 5 6
(#4 ON)
Perform Installation Test Suite 1
DIP Switches
DriverType:
On/Off
(no dimming)
WiredSensor:
None
On 1 2 3 4 5 6
(#4 ON)

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
10
Figure 15: Switching Contactors
ThiscongurationallowstheWA100-PMtoprovideOn/Off
switchingcontroltoanexternalcontactor.
7Wiring Continued
OFF
ON
Perform Installation Test Suite 1
DIP Switches
DriverType:
On/Off
(no dimming)
WiredSensor:
None
On 1 2 3 4 5 6
(#4 ON)

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
11
Figure 17: Emergency and Regular Light Fixtures: Wiring
to Dim while Regular Power is Available
Inthisapplication,theWA100-PMispoweredbytheRegular
powercircuitandisinstalledinsidetheRegularLightFixture.
While Regular power is supplied to the RRU-2 the WA100-PM
providesswitchedOn/OffpowertotheRegularLightFixture.
The WA100-PM also controls dimming to the Regular and
EmergencyLightFixture.The0-10Vdimmingcircuitfromthe
WA100-PMisbroughtintotheEmergencyLightFixture.The
EmergencyLightFixtureispoweredbytheEmergency
power circuit.
WhentheRRU-2senseslossofRegularpower,theRRU-2
disconnects the 0-10V output from the WA100-PM and the
EmergencyLightFixtureoperatesatmaximumoutputfromthe
Emergencypowercircuit.(Note:IftheRRU-2isnotinstalled,the
EmergencyFixturewilldimtominimumbecausetheWA100-PM
0-10V output shorts when the adapter loses power.)
7Wiring Continued
Set DIP switches and perform Installation Test appropriate
to 0-10v dimming and connected sensors.
Inthewiringdiagramhere,whileRegularpowerissuppliedtothe
LVSmodelRRU-X-UMtheWA100-PMprovidesswitchedOn/Off
powerand0-10Vdimmingcontroltothexturedriverorballast.
When the RRU-X-UM senses loss of Regular power it passes
Emergencypowerdirectlytothexture.Itdisconnectsthe
WA100-PM switched output and disconnects the WA100-PM
dimmingcontrolsothatthexturewilloperateatmaximum
output during the power failure.
Figure 16: Bypass WA100 switched power and 0-10V
dimming control during power failure

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
12
Figure 18: Secure unused wires
Figure 19: Mounting in driver channel
Figure 20: Mounting with the
included bracket
Figure 21: Mounting external to the top
of a suspended xture
Securing Low Voltage Wires
1.MakesuretheunitisNOTpowered.
2. Cuttheunusedlowvoltagewiresapproximatelyve
 inchesfromwheretheyexittheWA100-PMbody.
TheWA100-PMisdesignedsothatitcanbemountedinavariety
ofways.Dependingontheconstructionofthextureanditsability
topropagateradiosignals,itcanbemountedinsidethexturein
theballast/driverchannel.Aprintedbarcodelabelwiththefull
IEEEaddressisincludedwiththeWA100-PM.Afxthislabeltothe
outsideofthexture.Chooseastandardlocationsothatwhen
someonelooksforxturescontainingaWA100-PM,theywill
easilyndit.
UsingtheMountingBracket
ThemountingbracketincludedwiththeWA100-PMandshownin
theillustrationbelowprovidesascrewmountingalternative.
Thebrackethasaslotthatallowswirestoremainconnectedasyou
snapthebracketontotheWA100-PMnipple.TheWA100-PM
canbesecuredattheotherendusingtheintegralscrewtab.
Alternatively,itcanbemountedexternallytoajunctionbox,
enclosure,orxturehousingthrough
a1/2”knockout.
3.Isolatetheendofeachwireusingawirenut,shrinktubing,or 
equivalent.
4. Wrap the unused low voltage wires around the side of the
 adapterinabunch,andsecuretheminplaceusingawhiteor 
 clearcabletie.
8
9
Trimming and Dressing
Mounting

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
13
10
Alllightingdevices,includingwirelessadapters,mustbetested
for proper operation.
AftersettingtheDIPswitchesforyourapplication,mounting,
wiringlowvoltage,wiringlinevoltage,poweringupandresetting
theunit,performtherecommendedInstallationTest.The
InstallationTestmodeautomaticallytimesoutafter5minutes
of no activity.
WhiletheWA100-PMisinInstallationTestmode,thelowvoltage
devices connected to the WA100-PM directly control the lights
wiredtothesameWA100-PM.AfteryouexittheInstallationTest
mode,thelightsturnOnandareNOTcontrolledbythedevices
connected to the WA100-PM. After commissioning the Daintree
Networkedsystem,lightingcontrolisdeterminedbyconguration
settings in the Daintree Controls Software.
IMPORTANT NOTICES
Complete Installation Tests
Successful commissioning is dependent on testing each
wireless-adaptedlightingxtureand/orcontroldeviceatthe
timeofinstallation.Findinginstallationissuesordeviceproblems
earliersavessignicanttimeduringthecommissioningprocess.
Record IEEE Addresses
Ifyouhavenotalreadydoneso,besurethateachWA100-PM’s
IEEEaddress(last4or5digits)isrecordedonthefacilityoor
plan.Youcanusethe4or5digitlabelsuppliedwiththe
WA100-PMoryoucanwritethelast4or5digitsontheoorplan.
Thisinformationwillbeusedduringthecommissioningprocess.
Afterthelightinginstallationiscomplete,amarked-upcopyof
thefacilityoorplanshowingtheidentityandlocationofeach
wirelessadapter(includingassociatedlightxtures,switchesand
sensors)shouldbeavailable.Thiswillsimplifyandexpeditethe
commissioning process.
TestSuite1:
On/Off, Dimming, Alternate Switching or Bi-Level Drivers Only
1.PressandimmediatelyreleasetheblueResetbutton.The
  redErrorLEDashesonce,thenpausesandrepeats.
2.CheckthattheconnectedlightscycleOnandOff,orcycle
  frommaximumtominimumbrightnessthenturnOffper
  theDIPswitchconguration.
3.PressandimmediatelyreleasetheResetbuttontoexit 
testing.
4.PressandholdtheblueRESETbuttonontheWA100-PM 
  for3secondstoresettheunit.Releasethebutton
when the green Joined LED and the red Error LEDs
  beginashing.
TestSuite2:
Any Driver + Occupancy Sensor
1. PressandimmediatelyreleasetheblueResetbutton.
  TheredErrorLEDashesonce,thenpausesandrepeats.
2.CheckthattheconnectedlightscycleOnandOff,orcycle
  frommaximumtominimumbrightnessthenturnOff
  pertheDIPswitchconguration.
TestSuite2Continued:
3.PressandimmediatelyreleasetheblueResetbuttonagain.
  TheredErrorLEDashestwice,
then pauses and repeats.
4. Trigger the occupancy sensor. The light connected to the
driver turns On. When the sensor
times out the light turns Off.
5.PressandimmediatelyreleasetheResetbuttontoexit
testing.
6. PressandholdtheblueRESETbuttonontheWA100-PM 
  for3secondstoresettheunit.Releasethebutton
when the green Joined LED and the red Error LEDs
  beginashing.
Installation Tests
TestSuite3:
Dimming Driver + Occupancy Sensor + Photosensor
1.PressandimmediatelyreleasetheblueResetbutton.The
  redErrorLEDashesonce,thenpausesandrepeats.
2. Checkthatthelightsconnectedtothedrivercyclefrom 
  maximumtominimumbrightnessthenturnOff,then 
repeat.
3.PressandimmediatelyreleasetheblueResetbutton.The
  redErrorLEDashestwice,thenpausesandrepeats.
4. Trigger the occupancy sensor. The green Joined LED turns
On and the light connected to the driver turns On.
When the sensor times out the Joined LED and light
turns Off.
5.PressandimmediatelyreleasetheblueResetbuttonagain.
  TheredErrorLEDashesthreetimes,thenpauses
and repeats.
6. The light connected to the driver turns On.
7. The light’s output is proportional to the amount of light
  receivedbythephotosensor.
  •Fordimminglights,shineabrightlightatthe
   photosensor–thelightgetsbrighter.
Cover the photosensor – the light gets dim.
  •Forswitchedlights,coverthephotosensor–thelight 
   turnsOff.Shineabrightlightatthephotosensor–the 
light turns On.
8.PressandimmediatelyreleasetheResetbuttontoexit
testing.
9. PressandholdtheblueRESETbuttonontheWA100-PM 
  for3secondstoresettheunit.Releasethebutton
when the green Joined LED and the red Error LEDs
  beginashing.
TestSuite4:
Any Switch(es) + Any Matching Light Type(s)
 1.PressandimmediatelyreleasetheblueResetbutton.The
  redErrorLEDashesonce,thenpausesandrepeats.
 2.CheckthattheconnectedlightscycleOnandOff,orcycle
  frommaximumtominimumbrightnessthenturnOff
  pertheDIPswitchconguration.
 3.PressandimmediatelyreleasetheblueResetbuttonagain.
  TheredErrorLEDashesfourtimes,thenpauses
and repeats.

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
14
TestSuite8:
TestSuite9:
Dimming Driver + Photosensor
1.PressandimmediatelyreleasetheblueResetbutton.The
  redErrorLEDashesonce,thenpausesandrepeats.
2.Checkthatthelightsconnectedtothedrivercyclefrom 
  maximumtominimumbrightnessthenturnOff,
then repeat.
3.PressandimmediatelyreleasetheblueResetbuttonagain.
  TheredErrorLEDashesthreetimes,thenpauses
and repeats.
4. The light connected to the driver turns On.
5.Increasetheamountoflightatthephotosensorbyshining
  abrightlightatit.Thelight’soutputisproportional
  totheamountoflightreceivedbythephotosensor.
  • Fordimminglights,shineabrightlightatthe
   photosensor–thelightgetsbrighter.Coverthe
photosensor – the light gets dim.
  • Forswitchedlights,coverthephotosensor–thelight 
   turnsOff.Shineabrightlightatthephotosensor–the 
light turns On.
6. PressandimmediatelyreleasetheResetbuttontoexit 
testing.
7. PressandholdtheblueRESETbuttonontheWA100-PM 
  for3secondstoresettheunit.Releasethebutton
when the green Joined LED and the red Error LEDs
  beginashing.
Occupancy Sensor + Photosensor
1.PressandimmediatelyreleasetheblueResetbutton.The
  redErrorLEDashestwice,thenpausesandrepeats.
2. Trigger the occupancy sensor. The green Joined LED turns
On. When the sensor times out the Joined LED
turns Off.
3. PressandimmediatelyreleasetheblueResetbuttonagain.
  TheredErrorLEDashesthreetimes,thenpauses
and repeats.
4.ThegreenJoinedLEDbeginstoash.Increasetheamount
  oflightatthephotosensorbyshiningabrightlight
  atit.ThegreenJoinedLEDashesatafasterrate.
5.PressandimmediatelyreleasetheResetbuttontoexit 
testing.
6. PressandholdtheblueRESETbuttonontheWA100-PM 
  for3secondstoresettheunit.Releasethebutton
when the green Joined LED and the red Error LEDs
  beginashing.
TestSuite4:Continued
 4.Operatetheswitch(es)connectedtotheWA100-PMand 
  observethatthelightsturnOn,Off,andDimasexpected.
 5.PressandimmediatelyreleasetheResetbuttontoexit 
testing.
 6.PressandholdtheblueRESETbuttonontheWA100-PM 
  for3secondstoresettheunit.Releasethebutton
when the green Joined LED and the red Error LEDs
  beginashing.
TestSuite5:
TestSuite6:
TestSuite7:
Occupancy Sensor Only
1.PressandimmediatelyreleasetheblueResetbutton.
  TheredErrorLEDashestwice,thenpausesandrepeats.
2. Trigger the occupancy sensor. The green Joined LED turns
On. When the sensor times out the Joined LED turns Off.
3.PressandimmediatelyreleasetheResetbuttonto
  exittesting.
4. PressandholdtheblueRESETbuttonontheWA100-PM 
  for3secondstoresettheunit.Releasethebutton
when the green Joined LED and the red Error LEDs
  beginashing.
Photosensor Only
1.PressandimmediatelyreleasetheblueResetbutton.The
  redErrorLEDashesthreetimes,thenpauses
and repeats.
2.ThegreenJoinedLEDbeginstoash.Increasetheamount
  oflightatthephotosensorbyshiningabrightlight
  atit.ThegreenJoinedLEDashesatafasterrate.
3.PressandimmediatelyreleasetheResetbuttonto
  exittesting.
4. PressandholdtheblueRESETbuttonontheWA100-PM 
  for3secondstoresettheunit.Releasethebutton
when the green Joined LED and the red Error LEDs
  beginashing.
Switch Only (On/Off, Dimming, Alternate Switching or Bi-Level)
1. PressandimmediatelyreleasetheblueResetbutton. 
  TheredErrorLEDashesfourtimes,thenpauses
and repeats.
2. Operate the switch connected to the WA100-PM. The
green Joined LED turns On for the duration of the switch
  activation(appliestoOn,Off,andDimfunctions).
3.PressandimmediatelyreleasetheResetbuttontoexit 
testing.
4.PressandholdtheblueRESETbuttonontheWA100-PM 
  for3secondstoresettheunit.Releasethebuttonwhen 
  thegreenJoinedLEDandtheredErrorLEDsbegin
  ashing.
10 Installation Tests Continued

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
15
11 13
14
After the Installation Test is complete the WA100-PM is ready to
communicate with the Daintree Wireless Area Controller
(WAC)andtheDaintreeControlsSoftware(DCS)web-based
lightingmanagementuserinterface.Uponcommissioning,
theWA100-PM“Join”LEDturnsonsolidandremainsonaslong
astheWA100-PMisincludedintheZigBeeNetwork.
Afterjoiningthenetwork,thelowvoltagedevicesconnectedto
the WA100-PM do not directly control the lights that are
wired to the same WA100-PM. The control signals from the low
voltage devices pass through the WA100-PM and are sent
wirelesslytotheDaintreeNetworked.Dependingonthezone
anddevicecongurationintheDCS,wirelesssignalsfrom
the WAC to the WA100-PM determine the operation of the
light(s).
Formoreinformationaboutconguringthelightingcontrol
network,seetheinstructionsandon-linehelpprovidedwith
theDaintreeControlsSoftwarewebapplication.
The Installation Test procedure fails.
1.ConrmthattheWA100-PMispowered.
2.ChecktheconnectionsfromtheWA100-PMtothedriver(s)
and low voltage control devices.
3. ChecktobesuretheWA100-PMDIPswitchsettings
are correct.
4. PressandholdtheResetbuttonfor3secondstoreset
the WA100-PM.
5. Perform the Installation Test again.
Connected lights do not turn Off during the occupancy sensor
Installation Test.
1. Makesurethesensorisnotdetectingoccupancy.
2. Checktheoccupancysensortimedelayandmakesureitis
set for minimum.
When the Daintree Networked is commissioned, time delays are
set in the Daintree Controls Software system. These DCS “Off delays”
start counting down after the sensor’s internal time delay expires.
Therefore, set occupancy sensors for the minimum time delay
during the WA100-PM installation.
The red Error LED is ashing once every second.
DIPswitchcongurationisinvalid.AtleastoneDIPswitchmustbe
Ontoenableaninterface.
1. Enabletheinterface(s)thatareconnectedbyturning
appropriate DIP switch(es) On.
2. PresstheblueResetbuttonfor3 seconds to reset the unit.
Joining the Zigbee Lighting Control Network
12 Troubleshooting
Thisequipmenthasbeentestedandfoundtocomplywith
thelimitsforaClassBdigitaldevice,pursuanttoPart15of
theFCCRules.Theselimitsaredesignedtoprovidereasonable
protection against harmful interference in a residential
installation.Thisequipmentgenerates,usesandradiatesradio
frequencyenergyand,ifnotinstalledandusedinaccordance
withtheinstructions,maycauseharmfulinterferencetoradio
communications.However,thereisnoguaranteethat
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception,whichcanbedeterminedbyturningtheequipment
offandon,theuserisencouragetotrytocorrectthe
interferencebyoneormoreofthefollowingmeasures:
• Reorient or relocate the receiving antenna;
 • Increasetheseparationbetweentheequipment
and receiver;
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected;
 • Consultthedealeroranexperiencedradio/TVtechnician
for help.
ProductcomplieswithPart15oftheFCCRules.Operationis
subjecttothefollowingtwoconditions:(1)Thisdevicemaynot
causeharmfulinterference,and(2)Thisdevicemustacceptany
interferencereceived,includinginterferencethatmaycause
undesiredoperation.CANICES-005B/NMB-005B
FCC Warning Message
Industry Canada (IC) Warning Message

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
16
15
Plug load control functionality for the WA100-PM is made
availablewithWA100-PMrmwareprovidedinversion3.5.3.1.
DuringtestingthePlugLoadcycleson/offinsyncwiththe
lightingload.Relaysusedtocontrolplugloadsmustbe
compliantwithUL498(AttachmentPlugandReceptacles)
or equivalent.
Wiring for Combination Plug Load
(Basic Aux Relay) and Dimming Light
Inthewiringdiagrambelow,theWA100-PMisusedto
controlbothadimminglightandaplugloadcircuit.
Wiring for Combination Plug Load (Basic Aux Relay)
and On/Off Light
Inthewiringdiagrambelow,theWA100-PMisusedtocontrol
bothanOn/Offlightandaplugloadcircuit.
Plug Load Applications
OFF
ON
Perform Installation Test Suite 1
DIP Switches
Driver:On/Off+
0-10V dimming.
PlugLoad:
On/Off
WiredSensor:
None
On 1 2 3 4 5 6
(#2,3 On)
Perform Installation Test Suite 1
DIP Switches
Driver:
On/Off
PlugLoad:
On/Off
WiredSensor:
None
On 1 2 3 4 5 6
(#2,4 On)
OFF
ON
*0-10VDimmingoutput,5mAavailable,Upto10LEDdriversor
 uorescentballaststypical;thechanceofnoiseonthesignal
increases with more.
**RelaysusedtocontrolplugloadsmustbecompliantwithUL498
(Attachment Plug and Receptacles) or equivalant.

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
17
15
Wiring for Combination Plug Load (Aux Relay with
Input Control Signal) and Dimming Light
Inthewiringdiagrambelow,theWA100-PMisusedto
controlbothadimminglightandaplugloadcircuit.
Plug Load Applications Continued
Perform Installation Test Suite 1
DIP Switches
Driver:
On/Off+0-10V
dimming. Plug
LoadOn/Off
WiredSensor:
None
On 1 2 3 4 5 6
(#2,3 On)
OFF
ON
*0-10VDimmingoutput,5mAavailable,Upto10LEDdriversor
 uorescentballaststypical;thechanceofnoiseonthesignal
increases with more.
**RelaysusedtocontrolplugloadsmustbecompliantwithUL498
(Attachment Plug and Receptacles) or equivalant.

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
18
15
Wiring for Combination Plug Load (Aux Relay with Input
Control Signal) and On/Off Light
Inthewiringdiagrambelow,theWA100-PMisusedto
controlbothanOn/Offlightandaplugloadcircuit.
Plug Load Applications Continued
Perform Installation Test Suite 1
DIP Switches
Driver:On/Off
PlugLoad:
On/Off
WiredSensor:
None
On 1 2 3 4 5 6
(#2, 4 On)
OFF
ON
*0-10VDimmingoutput,5mAavailable,Upto10LEDdriversor
 uorescentballaststypical;thechanceofnoiseonthesignal
increases with more.
**RelaysusedtocontrolplugloadsmustbecompliantwithUL498
(Attachment Plug and Receptacles) or equivalant.

Installation GuideDaintree®Networked Wireless Adapter (WA100-PM)
Theseinstructionsdonotpurporttocoveralldetailsorvariationsinequipmentnortoprovideforeverypossiblecontingencytobemetinconnectionwithinstallation,operation
ormaintenance.Shouldfurtherinformationbedesiredorshouldparticularproblemsarisewhicharenotcoveredsufcientlyforthepurchaser’spurposes,themattershouldbe
referredtoGECurrent,aDaintreecompany.
Questions:
Web: products.gecurrent.com
Phone: [phone]
www.gecurrent.com
©2021CurrentLightingSolutions,LLC.Allrightsreserved.GEandtheGEmonogramaretrademarksofthe
GeneralElectricCompanyandareusedunderlicense.Informationprovidedissubjecttochangewithoutnotice.
Allvaluesaredesignortypicalvalueswhenmeasuredunderlaboratoryconditions.
DT113(Rev.04/28/2021
CAUTION
RISK OF EXPOSURE IF BATTERY IS REPLACED BY AN
INCORRECT TYPE. DISPOSAL OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
WFA100-PM
Input Voltage 120-277VAC,50-60Hz
Switched Output  15Adriver/incandescent@120-277VAC
Relay 1hp@120-230VAC(switchedtoHot/Active)
Low Voltage 24VDC;75mAmaximum
Output
Low Voltage Intel®Atom™ProcessorE3805
Wiring
Memory and 22AWG,600V,UL1015,plenumratedMax. 
Storage recommended length of up to 100’ (30m)
Analog Dimming 0-10VDC,5mAmax(sinkorsource),upto
  10typical0.5mAsinkingdrivers/ballasts* 
Analog Input Photosensor 0-10VDC
Digital Input (2) Activehigh.Occupancysensor,
  DimUp/Down(switchmode)
Digital Output LSD(lowsidedriver)auxrelaycontrol,
  75mAmaximum(includingattached
sensors)
Radio Properties 2.4GHz,+8dBm,Rangedependent
  onRFpropagationvariablessuch
  asmetalobstacles
Operating Indoor,drylocation
Environment -4°to149°F(-20°to65°C)
Compliance CSAcertied,plenumrated,
  FCCPart15,CAIC
Mounting 1/2”knockout,screwtab,optional 
  mountingbracketsupplied
Dimensions 9.4”Lx1.7”Wx1.18”H
10.1”Lx1.7”Wx1.18”Hwith
  mountingbracket
Specications
*“Driver”referencesinclude“ballasts”unlessotherwisenoted.