DAMSON S-SERIES User manual

USER GUIDE
S-SERIES
damsonglobal.com

User Guide for S-Series Home Cinema
Insert batteries
into Remote Control.
Unpack all contents
including power supplies.
1
Position the Soundbar
in front of the display
(TV/Projector),
connect power cable.
Insert the HDMI sources
into the Subwoofer.
Insert the
HDMI output that will
connect to the display.
5
10
67
23
AAA
AAA
Select a location for the first S-Cube surround
speaker, connect power cable. For left surround
move switch on S-Cube to Triangle . For right
surround select square .
DC
4
8
Select a location for the Second S-Cube
surround speaker, connect power cable and
position the switch to the appropriate icon for left
or right surround.
DC
HDMI
INPUT 1
HDMI
OUTPUT
9
Couple the Dolby Atmos
speaker onto the soundbar,
it will snap into place.
Connect the power
supply to the sub-woofer.
The Logo will turn red on
the subwoofer.
The system will now power up and configure itself.
The Subwoofer logo will turn blue, the Soundbar
logo will light up red and the S-Cubes logo will
display light blue.
Please note: On initial set up it is recommended to connect the power
supply of the subwoofer last as this provides auto-power upon initial
setup. If the subwoofer is powered up before the other speakers are
connected you will need to power off the subwoofer either by removing
the power cable or pressing the power button on the remote control
until the LED turns off, then power on again by remote control.
Please note: The S-Cubes
are set up to power on
automatically to the surround
sound system only when
connected to a power supply.
Dolby, Dolby Atmos, Dolby Audio,
Pro Logic, and the double-D symbol
are trademarks of Dolby Laboratories

Dolby®Atmos Wireless Home Cinema System
SPEAKER GUIDE
Perspektive deailSpeaker placement
1
1. Seating position
2. S-cube left speaker
3. S-cube right speaker
4. S-Bar with Dolby Atmos extension
5. S-Woofer*
*S-Woofer LED will flash when it is receiving Dolby Atmos Content
2
45
3

Using your TV's ARC Function Remote control
1
4
b. Press the “ARC”
button in the
Remote Controller
a. Press the “Power”
button in the S-Bar
quickly
Plug the HDMI
cable into the port
HDMI(ARC) on TV
Ensure the TV has the ARC port
HDMI
(ARC)
2HDMI
(ARC)
3HDMI
OUTPUT
Insert the other end of the
HDMI cable into S-Woofer
HDMI Out port
Change the S-Series to the “ARC”
mode (the LED light will be “white”
color in the S-Bar):
There are 2 ways to change to the
“ARC” mode:
4a.
XBASS
Power Mute
4b.
Blue Buttons only work when in Bluetooth mode.
Pressing the X-Bass button will optimise the sound
for music or tv viewing. When the Logo is Blue it is
set for music. when it is red it is set for TV audio.
The LED colours on the
soundbar when you press
some of these buttons
XBASS
Volume
Power Mute
Pair Play/Pause
Previous Next
HDMI 1
Red
HDMI 2
Indigo
ARC
White
AUX
Green
BT
Blue

Using S-Series for Home Cinema
With the Atmos module added experience Full 3D
surround sound through Dolby Atmos
Soundbar and Subwoofer will deliver
Dolby Virtual Surround sound,
Multi-Room Audio
The S-Cubes speakers can also be used as either
standalone speakers or multi-room speakers using
Damson JetStreamNet.
Soundbar and Subwoofer with 2 S-Cubes
work as Dolby 5.1 surround supporting
Dolby Digital+ and Dolby TrueHD

User Guide for S-Cube
Power/Mode (BT/Aux/JSN),
Vol –, Vol +, Play/Pause.
1. JetStreamNet Pairing,
2. Trangle, 3. Circle, 4. Square
5. Reset, 6. AUX In, 7. AC/DC Input
1.
2.
5.
6. 7.
3. 4.

XBASS
Power Mute
1. Individual
Stereo Speaker
DC
AUX
Insert a cable into the AUX
port for wired connectoin.
The LED will light up yellow.
If selecting BT pair your
device to Damson
S-Cube. Function mode
should be set to Circle
2. Multi Speaker
1
DC
3
Select a primary speaker to
connect to your device to
S-Cube. Power on additional
speakers and change
function to JetStreamNet
mode (light blue LED).
Bring the additional speakers close to the primary speaker
and press and hold the JSN Pairing button for 3 seconds
on both speakers at the same time. Speakers are now
connected. Repeat for up to 8 speakers.
Change the output of each speaker. Select Triangle for
Stereo left channel and Square for Stereo Right channel,
or circle on each device if you wish to play stereo on each
speaker.
3. S-Series Surround
Power On the
S-Woofer with remote
control.
Change the mode
on the S-Cubes to
JetStreamNet (light blue).
On the remote control
press and hold the Wireless
button for 3 seconds.
Pairing will complete.
1
1
2
3
On the left surround
speaker change the output
switch to triangle.
4
On the right surround
speaker change the output
switch to square.
5
2
DC
33 sec.
S-Cube has three primary functions:
2
DC
Speaker 1 Speaker 2
3 sec. 3 sec.
DC
Power on and change mode
to either BT (Blue LED) or