Danfoss 140F1080 User manual

www.DEVI.com
Installation Guide
DEVIreg™ 610
Electronic Thermostat

DEVIreg™ 610
Installation Guide2

DEVIreg™ 610
Installation Guide 3
1 Introduction
DEVIreg™ 610 is an electronic thermostat to be installed
directly on the wall. It is provided with a 2-pole switch and a
wire sensor to control the desired temperature.
The thermostat has a button for adjusting the temperature
setting with a scale from -10 °C to +50 °C, and an LED
indicator that shows standby periods (green light) and
heating periods (red light).
More information on this product can also be found at:
devireg.devi.com
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specifications . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . 6
3 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Disposal Instruction . . . . . . . . . . . . . . . . . . 13

DEVIreg™ 610
Installation Guide4
1.1 Technical Specifications
-30°C to +50°C 220-240V~, 50Hz
Standby power consumption Max. 0,93W
Relay:
Resistive load
Inductive load
Max 10A / 2300W @ 230V
cos φ= 0.3 max 1A
Sensing units NTC 15kOhm at 25°C
Sensing values:
0 °C
25 °C
50 °C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ±0,2 °C
Ambient temperature -30 °C to +50 °C
Temperature range -10 °C to +50 °C
Cable specification max 1 x 4 mm² or 2 x 2,5 mm²
Ball pressure temperature 75 °C
Pollution degree 2 (domestic use)
Type 1C
Storage temperature -20 °C to +65 °C
IP class 44
Protection class Class II -

DEVIreg™ 610
Installation Guide 5
Dimensions 100 x 69,5 x 45 mm
Weight 165 g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned off
before installation.
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualified installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.

DEVIreg™ 610
Installation Guide6
2 Mounting Instructions
Please observe the following placement guidelines:
• The thermostat can be placed both indoors and
outdoors.
• Place the thermostat on a wall, pole, steel/wooden
plate or pipe.
In wet rooms, place the thermostat according to
local regulation on IP classes.

DEVIreg™ 610
Installation Guide 7
Follow the steps below to mount the thermostat.
1. Open the thermostat:
• Set adjustment button to minimum temperature.
• Loosen the 2 screws and open the front cover.

DEVIreg™ 610
Installation Guide8
2. Fasten the thermostat:
• Drive the screws through the holes in the bottom
corners of the thermostat.
• Seal the holes with the enclosed screw stopper to
maintain the density.
3. Connect the thermostat according to the connection
diagram.
IP44
-10T50
D610
LNNNONC NTC
Mains
220-240V~
L
N
Sensor
Max.Load
10 (1) A
• Heating: (L-main, N-main, L-load, NO (normally open)
- load).
• Cooling: (L-main, N-main, L-load, NC (normally closed)
- load).

DEVIreg™ 610
Installation Guide 9
The screen of the heating cable must be connected to
the earth conductor of the power supply cable by using
a separate connector.
4. Reinstall the front cover.
5. Ensure that the adjustment button can be adjusted
within full temperature range, i.e. from -10 °C to
+50 °C.
6. Install sensor using the supplied sensor cable - spec.
NTC 15 kΩ @ 25°C.
• Press out the blanket located at the bottom of the
thermostat and insert the seal nipple.
• Connect sensor to terminals 6+7.
The sensor cable can be extended up to 50 m with
1,5 mm² installation cable without affecting the
accuracy of the thermostat.
Do not place the cable parallel to other installation
cables as undesirable signals may be induced.
The installation must be permanent.
If the sensor is to be built in, used for pipe
applications, or exposed to pressure, always install it
in a conduit.
7. Turn on the power supply.

DEVIreg™ 610
Installation Guide10
3 Warranty
A 2-year product warranty is valid for:
• thermostats: DEVIreg™ 610.
Should you, against all expectations, experience a problem with your DEVI product,
you will find that Danfoss offers DEVIwarranty valid from the date of purchase
on the following conditions: During the warranty period Danfoss shall offer a new
comparable product or repair the product if the product is found to be faulty by
reason of defective design, materials or workmanship. The repair or replacement.
The decision to either repair or replace will be solely at the discretion of Danfoss.
Danfoss shall not be liable for any consequential or incidental damages including,
but not limited to, damages to property or extra utility expenses. No extension of the
warranty period following repairs undertaken is granted.
The warranty shall be valid only if the WARRANTY CERTIFICATE is completed
correctly and in accordance with the instructions, the fault is submitted to the
installer or the seller without undue delay and proof of purchase is provided. Please
note that the WARRANTY CERTIFICATE must be filled in, stamped and signed by the
authorized installer performing the installation (Installation date must be indicated).
After the installation is performed, store and keep the WARRANTY CERTIFICATE and
purchase documents (invoice, receipt or similar) during the whole warranty period.
DEVIwarranty shall not cover any damage caused by incorrect conditions of use,
incorrect installation or if installation has been carried out by non-authorized
electricians. All work will be invoiced in full if Danfoss is required to inspect or
repair faults that have arisen as a result of any of the above.The DEVIwarranty shall
not extend to products which have not been paid in full. Danfoss will, at all times,
provide a rapid and effective response to all complaints and inquiries from our
customers.
The warranty explicitly excludes all claims exceeding the above conditions.
For full warranty text visit www.devi.com.
devi.danfoss.com/en/warranty/

DEVIreg™ 610
Installation Guide 11
WARRANTY CERTIFICATE
The DEVIwarranty is granted to: Address Stamp Purchase date Serial number of the product Product Art. No. *Connected output [W] Installation Date & Signature
Connection Date & Signature
*Not mandatory

DEVIreg™ 610
Installation Guide12

DEVIreg™ 610
Installation Guide 13
4 Disposal Instruction

DEVIreg™ 610
Installation Guide14

08095435 & AQ057986478203en-020306 © Danfoss | 2023.03
Danfoss A/S
Nordborgvej 81
6430 Nordborg, Syddanmark
Denmark

dYHAd DEVIreg™ 610 140F1080 220-240 V~ 50-60 Hz~ -10 to +50 °C 10 A / 2300 W @ 230 V~ IP 44
Product documentation
0
I
˚C
50
30
10
-10
Designed in Denmark for Danfoss A/S
*08095435*
5703466209257
DK EL 7224215344 SE EL 8581196 NO EL 5491490 FI SSTL 3531041
For UK customer only: Importer: Danfoss Ltd., 22 Wycombe End, HP9 1NB, GB