Danfoss 140F1143 User manual

www.DEVI.com
Installation Guide
DEVIreg™ Smart
Intelligent Electronic Timer Thermostat or Timer
Switch with Wi-Fi connectivity and App control

DEVIreg™ Smart
Installation Guide2
1 Introduction
DEVIreg™ Smart is an electronic programmable timer
thermostat used for controlling electrical oor heating
elements. The thermostat is designed for xed installation
only and can be used for both direct heating of the entire
room and for comfort heating of the oor. Among others,
the thermostat has the following features:
• A touchscreen display with light.
• An easy-to-follow menu-driven programming and
operation (requires an app).
1 Introduction . . . . . . . . . . . . . . . . . . . . . . 2
2 Technical Specications . . . . . . . . . . . . . . . 4
3 Safety Instructions . . . . . . . . . . . . . . . . . . 6
4 Mounting Instructions . . . . . . . . . . . . . . . . 8
5 Display Symbols . . . . . . . . . . . . . . . . . . . 13
6 Configuring . . . . . . . . . . . . . . . . . . . . . . 19
7 Settings . . . . . . . . . . . . . . . . . . . . . . . . 20
8 Warranty. . . . . . . . . . . . . . . . . . . . . . . . 23
9 Radio Equipment Directive . . . . . . . . . . . . 26
10 Disposal Instruction . . . . . . . . . . . . . . . . 27
Table of Contents

DEVIreg™ Smart
3Installation Guide
• An installation wizard with room/oor type-specic
setup (requires an app).
• Support for multiple frame systems.
• Compatible with several 3rd party NTC sensors.
• Thermostat settings can be specied before instal-
lation and imported to the thermostat using a web-
generated code (For DEVIreg™ Touch), or copied
from a thermostat in a similar installation. This
includes DEVIreg™ Touch thermostats.
• Smart access via app to thermostat settings after
installation, for easy access, setup or remote trou-
bleshooting. Thermostat/timer will continuously be
updated with newest version of software.
• DEVIreg™ Smart can be used as a switch for On/O
systems
Regarding Connectivity:
• 10 smart devices (like Smartphone or Tablet) can be
connected to 1 thermostat/switch.
• 2 smart devices can be in contact with the thermo-
stat/switch at the same time.
DEVIREG™ SMART REQUIRES WORKING Wi-Fi
TO FUNCTION .

DEVIreg™ Smart
Installation Guide4
More information on this product can also be found at:
devismart.com
2 Technical Specications
Operation voltage 220–240 V~, 50/60 Hz
Standby power
consumption
Max. 0,40 W
Relay:
Resistive load
Inductive load
Max. 16 A / 3680 W @ 230 V
Max. 1 A cos φ= 0,3
Sensing units* NTC 6,8 kOhm at 25°C
NTC 10 kOhm at 25°C
NTC 12 kOhm at 25°C
NTC 15 kOhm at 25°C (Default)
NTC 33 kOhm at 25°C
NTC 47 kOhm at 25°C
Sensing values*:
(Default NTC 15 K)
0 °C
20 °C
50 °C
42 kOhm
18 kOhm
6 kOhm
Control* PWM (Pulse Wide Modulation)
Ambient temperature 0°C to 30°C
Frost protection
temperature*
5°C to 9°C (default 5°C)

DEVIreg™ Smart
5Installation Guide
Temperature range* Room temperature: 5°C to 35°C.
Floor temperature: 5°C to 45°C.
Max. oor: 20°C to 35°C (if unrecover-
able seal is broken then up to 45°C).
Min. oor: 10°C to 35°C, only with
combination of room and oor sensor.
Sensor failure monitoring* The thermostat has a built-in
monitoring circuit, which will switch
o the heating if the sensor is
disconnected or short-circuited.
Timer functions 2 periods per day for DEVIweb™.
5 periods per day for DEVIsmart App.
All clock/date/schedule settings are
updated from the cloud.
Set-point resolution of timer is
30minutes.
Cable specication max. 1x4 mm2
Ball pressure test tem-
perature
75°C
Pollution degree 2 (domestic use)
Controller type 1C
Software class A
Storage temperature -20°C to +65°C
IP class 21
Protection class Class II -

DEVIreg™ Smart
Installation Guide6
Dimensions 85 x 85 x 20-24 mm
(in-wall depth: 22 mm)
Weight 127 g
* not relevant for switch function
Electrical safety and Electro-Magnetic Compatibility
for this product is covered by the compliance with the
EN/IECStandard“Automatic electrical controls for house-
hold and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-7 (timer)
• EN/IEC 60730-2-9 (thermostat)
3 Safety Instructions
Make sure the mains supply to the thermostat/switch is
turned o before installation.
Important: When the thermostat is used to control a
oor heating element in connection with a wooden oor
or similar material, always use a oor sensor and never set
the maximum oor temperature to more than 35°C.
Please also note the following:
• The installation of the thermostat /switch must be done
by an authorized and qualied installer according to
local regulations.

DEVIreg™ Smart
7Installation Guide
• The thermostat /switch must be connected to a power
supply via an all-pole disconnection switch.
• Always connect the thermostat /switch to continuous
power supply.
• Do not expose the thermostat /switch to moisture,
water, dust, and excessive heat.
• This thermostat /switch can be used by children aged
from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of expe-
rience and knowledge, if they have been given supervi-
sion or instruction concerning use of the appliance in
a safe way and understand the hazards involved, by a
person responsible for their safety.
• DEVIreg™ Smart can modied to work as a timer on/
o switch by downloading new software with new
functionality.
• Children should be supervised to ensure that they do
not play with the thermostat /switch .
• Switch is designed for permanent operation.
• Not for uorescent lamps and lament lamps.
• Cleaning and user maintenance shall not be made by
children without supervision.
• Updating to timer switch function may take up to
1hour. Same time should be expected if function is to
be rolled back to thermostat functionality.

DEVIreg™ Smart
Installation Guide8
4 Mounting Instructions
Please observe the following placement guidelines:
Place the thermostat at a suitable height on the wall
(typically 80–170 cm). Switch can be placed on free
area on the wall.
The thermostat/switch should not be placed in wet
rooms. Thermostat/switch must be placed outside
zone 2. Place it in an adjacent room and use oor
sensor only. Always place the thermostat/switch
according to local regulation on IP classes.
Do not place the thermostat on the inner side of a
poorly insulated exterior wall.
Always install the thermostat at least 50 cm from
windows and doors, due to draft, when using regulation
in: oor and room mode or room alone mode.
Do not place the thermostat in a way that it will be
exposed to direct sunlight.

DEVIreg™ Smart
9Installation Guide
Note for thermostat: A oor sensor is recommend-
ed in all oor heating applications and mandatory
to thin mats and under wooden oors to reduce the
risk of over-heating the oor.
• Place the oor sensor in a protecting plastic conduit
in the oor construction in an appropriate place,
where the oor is not exposed to sunlight or draft
from door openings.
12
≥
• Equally distant and
>2 cm from the
heating cables on
both sides.
• The conduit should
be ush with the
oor surface, coun-
tersink the conduit
if necessary and
possible.
• Route the conduit to the connection box.
• The bending radius of the conduit must be min 50 mm.

DEVIreg™ Smart
Installation Guide10
Follow the steps below to mount the thermostat/switch:
1. Unpack thermostat/switch.
2.1. Connect the thermostat according to the connection
diagram.
IP21
T30
Mains
220-240V~
50-60 Hz
Maximum
Load 16 (1) A
Sensor
NTC
Danfoss A/S
Nordborgvej 81
6430 Nordborg
Denmark
NLL
L
O
A
DN
L
O
A
D
Standby maximum 0.4 Watt
The screen of the heating
cable must be connected to
the earth conductor of the
power supply cable by using
a separate connector.
Note: Always install the oor sensor in a conduit in
the oor.
IP21
T30
Mains
220-240V~
50-60 Hz
Maximum
Load 16 (1) A
NTC
Danfoss A/S
Nordborgvej 81
6430 Nordborg
Denmark
NLL
L
O
A
DN
L
O
A
D
Standby maximum 0.4 Watt
2.2. Connect the switch ac-
cording to the connection
diagram.
3. Fasten the thermostat/switch rmly to a ush
mounted wall box or an exterior wall box by driving