Danfoss DEVIreg 330 User manual

www.DEVI.com
Installation Guide
DEVIreg™ 330 (+5 to +45°C)
Electronic Thermostat
EN

DEVIreg™ 330 (+5 to +45°C)
3Installation Guide
1 Introduction
DEVIreg™ 330 is an electronic thermostat to be installed in
electric cabinets with DIN rail attachment. The thermostat
must be installed via an all-pole disconnection switch.
Either a floor sensor or an external room sensor must be
used to measure and control the desired temperature.
The thermostat has a button to adjust the temperature
setting with a scale from +5 to +45°C. An LED indicator
shows standby periods (green light) and heating periods
(red light).
More information on this product can also be found at:
devireg.devi.com
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specifications . . . . . . . . . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6 Disposal Instruction . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table of Contents

DEVIreg™ 330 (+5 to +45°C)
Installation Guide4
1.1 Technical Specifications
Operation voltage 220-240 V~, 50 Hz
Standby power consumption Max 0,25 W
Relay:
Resistive load
Inductive load Max 16 A / 3680 W @ 230 V cos φ= 0,3 max1A
Sensing units NTC 15 kOhm at 25 °C
Sensing values:
0 °C
25 °C
50 °C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ± 0,2 °C
Ambient temperature 10 °C to +50 °C
Lowering in economy periods -5 °C
Temperature range +5 °C to +45 °C
Cable specification max 1x4 mm2or 2x2,5 mm2
Ball pressure temperature 75 °C
Pollution degree 2 (domestic use)
Type 1C
Storage temperature -20 °C to +65 °C
IP class 20

DEVIreg™ 330 (+5 to +45°C)
5Installation Guide
Protection class Class II
Dimensions 86 x 36 x 58 mm
Weight 83 g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned off
before installation.
IMPORTANT: When the thermostat is used to control a
floor heating element in connection with a wooden floor or
similar material, always use a floor sensor and never set the
maximum floor temperature to more than 35°C.
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualified installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have this
in mind if the sensor must be extended.

DEVIreg™ 330 (+5 to +45°C)
Installation Guide6
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
2 Mounting Instructions
Please observe the following placement guidelines:
• Install the thermostat in an electric cabinet with DIN
rail attachment or a separate DIN attachment accord-
ing to local regulation on IP classes.
• Do not place the thermostat in a way that it will be
exposed to direct sunlight.
Follow the steps below to mount the thermostat:
1. Click the thermostat on to the DIN rail attachment.
2. Connect the thermostat according to the connection
diagram.
+5°C to +45°C

DEVIreg™ 330 (+5 to +45°C)
7Installation Guide
N
L
PE
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note: When you use the wire sensor for floor heating,
always install the sensor in a conduit.
3. Turn on the power supply.

DEVIreg™ 330 (+5 to +45°C)
Installation Guide8
4 Settings
If a floor sensor is used, please be aware of the following:
• The floor temperature is measured where the sensor is
placed.
• The temperature of the bottom of a wooden floor can
be up to 10 degrees higher than the top.
• Floor manufactures often specify the max temperature
on the top surface of the floor (usually 27-28˚C).
• Always use a floor sensor to control floor heating.
Without a floor sensor, the temperature control may be
less accurate and you risk overheating the floor.
Thermal
resist-
ance
[m²K/W]
Examples of
ooring
Details Approximate
setting for
25˚C oor
temperature
0,05 8 mm HDF based
laminate
> 800 kg/m³ 28˚C
0,10 14 mm beech
parquet
650 - 800 kg/m³ 31˚C
0,13 22 mm solid oak
plank
> 800 kg/m³ 32˚C
< 0,17 Max. carpet
thickness suitable
for floor heating
acc. to EN 1307 34˚C
0,18 22 mm solid fir
planks
450 - 650 kg/m³ 35°C

DEVIreg™ 330 (+5 to +45°C)
9Installation Guide
5 Warranty
A 2-year product warranty is valid for:
• thermostats: DEVIreg™ 330 (+5 to +45° C).
Should you, against all expectations, experience a problem with your DEVI product,
you will find that Danfoss offers DEVIwarranty valid from the date of purchase on
the following conditions: During the warranty period Danfoss shall offer a new com-
parable product or repair the product if the product is found to be faulty by reason
of defective design, materials or workmanship.The repair or replacement.
The decision to either repair or replace will be solely at the discretion of Danfoss.
Danfoss shall not be liable for any consequential or incidental damages including,
but not limited to, damages to property or extra utility expenses. No extension of the
warranty period following repairs undertaken is granted.
The warranty shall be valid only if the WARRANTY CERTIFICATE is completed
correctly and in accordance with the instructions, the fault is submitted to the
installer or the seller without undue delay and proof of purchase is provided. Please
note that the WARRANTY CERTIFICATE must be filled in, stamped and signed by the
authorized installer performing the installation (Installation date must be indicated).
After the installation is performed, store and keep the WARRANTY CERTIFICATE and
purchase documents (invoice, receipt or similar) during the whole warranty period.
DEVIwarranty shall not cover any damage caused by incorrect conditions of use,
incorrect installation or if installation has been carried out by non-authorized electri-
cians. All work will be invoiced in full if Danfoss is required to inspect or repair faults
that have arisen as a result of any of the above. The DEVIwarranty shall not extend to
products which have not been paid in full. Danfoss will, at all times, provide a rapid
and effective response to all complaints and inquiries from our customers.
The warranty explicitly excludes all claims exceeding the above conditions.
For full warranty text visit www.devi.com.
devi.danfoss.com/en/warranty/

DEVIreg™ 330 (+5 to +45°C)
Installation Guide10
WARRANTY CERTIFICATE
The DEVIwarranty is granted to:
Address Stamp
Purchase date
Serial number of the product
Product Art. No.
*Connected output [W]
Installation Date
& Signature
Connection Date
& Signature
*Not mandatory

DEVIreg™ 330 (+5 to +45°C)
Produced by Danfoss © 01/202308091289 & AQ087986471595en-020204
Danfoss A/S
Nordborgvej 81
6430 Nordborg, Syddanmark
Denmark
6 Disposal Instruction

DEVIreg 330 +60<>+160˚
140F1073
220-240V~
50-60Hz~
+60 to +160˚C
16A/3680W@230V~
Product Documentation
DK EL 7224215328
SE EL 8581188
NO EL 5402664
FI SSTL 3531034
Designed in Denmark for Danfoss A/S
5703466209233

For UK customer only: Importer:
Danfoss Ltd., 22 Wycombe End, HP9 1NB, GB
DEVIreg™ 330 (+5 °С to +45 °C)
140F1072
DK EL 7224215315
SE EL 8581185
NO EL 5491481
FI SSTL 3531031
220-240V~
50-60Hz~
+5 to +45°C
16A/3680W@230V~
5 703466 209226