Danfoss TP5001 series User manual

TP5001 + RF
Electronic 5/2 day programmable room thermostat
User Instructions
Bedienungsanleitung
Instrucciones del usuario
Brugervejledning
GB
®
Certification Mark
D
ES
Instructies voor gebruik
Instrukcja Użytkownika
Vartotojo instrukcija
DK
NL
P
LT

2
An introduction to your programmable room thermostat
Your programmable room thermostat allows you to programme
dierent temperatures at dierent time periods. You can programme
one set of times and temperatures for week days with a dierent set of
temperatures for weekend days, this is referred to as 5/2 day operation.
The thermostat can also be set up by your installer to provide one set
of times and temperatures that are repeated each day of the week. This
is referred to as 24 hour operation.
The thermostat can also be set by you to provide two dierent
programming blocks which can then be assigned to any day of the
week, this is referred to as A/B programme operation.
All thermostats can be set by your installer to provide up 2, 4 or 6 time
and temperature settings each day.
All thermostats feature useful overrides, including a programmable
frost setting.
Your thermostat has some advanced features which the installer will
set-up if they are required.There are also a number of advanced features
which can be set up by you. These advanced settings alter the way that
your thermostat operates, some also aect the programming functions
and the user overrides. Please read the User Advanced Programming
instructions before programming the unit (see page 10).
Preset programmes
Your TP5001 comes ready programmed with a set of operating times and
temperatures which suit most people. Please remember that some of the
options available will depend on how the installer has set up the unit.
User Instructions
User Instructions
GB
Weekdays (Mon-Fri) Weekend (Sat-Sun)
Event Time Temp. °C Event Time Temp. °C
1 06:30 20 1 07:30 20
2 08:30 15 2 09:30 20
3 11:30 20 3 11:30 20
4 13:30 15 4 13:30 20
5 16:30 21 5 16:30 21
6 22:30 15 6 22:30 15
Note: these are also times for Block
“A”programmes
Note: these are also times for Block“B”
programmes

3
Note: If set up for 4 events per day, events 3 & 4 are skipped. If set up
for 2 events per day, events 2, 3, 4 & 5 are skipped. In both cases the
events are re-numbered.
Before you start
Open the ap on the front of the programmer and
press the RESET button with a non-metallic object
until the display goes blank. This will ensure that
the factory programmes are set and that the micro-
computer in the product is operating correctly.
Customising the display
For the sake of clarity, the instructions assume that the display setting
uses a 24 hour clock, °C and that days of the week are numbered 1-7,
(where 1 is Monday). All of these settings can be personalised after the
thermostat has been programmed, see pages 8 and 9.
Setting the correct date and time
Your TP5001 incorporates a real time clock with calendar function that
automatically changes time in both Spring and Autumn. The time and
date is set in the factory for the CET time zone, and does not normally
require adjustment. If you live in another time zone refer to“Time zone
oset” on page 11. However, should it be found necessary to adjust
time or date for any other reason refer to the following instructions.
User Instructions
GB
RESET
Setting the date
Press and hold Λand PROG for 3 seconds, to
display date in dd/mm/yy format.

4
The YEAR number will ash, use Λor Vto correct
the year.
Use -or +to move to MONTH, then use Λor Vto
correct month.
Use -or +to move to DATE in month, then use Λor
Vto correct day in month.
If you attempt to select an invalid date the unit software will reject it
and apply the nearest valid date. It is recommended that date is set in
the order, yy/mm/dd.
Setting the correct time
After setting the date, press PROG to display the
time. The time display will ash on and o.
Use the +and -buttons to set the correct time
(press and hold to change in 10 min. increments).
Setting the correct day
The day of the week is set automatically. Press
PROG to return to normal operation (RUN).
User Instructions
GB
Accepting the preset programmes
If you are happy with the preset times shown in the table on page 2 you
need take no further action.

5
User Instructions
GB
Changing the preset programmes
Before you change the preset programmes
Your installer will have set the unit to operate in one of the following
modes:
•5/2 day - one set of programmes for weekdays and another for
weekends (page 5-6).
•24 hr - one set of programmes for the whole of the week (page 6).
Alternatively
•A/B - The unit can also be set by you to provide two programme
blocks, either of which can be applied to dierent days of the week.
If this is required refer to page 6 for instructions on how to turn on
this feature.
Please Note
The unit must be programmed in sequence, event times cannot be
set out of sequence.
If you want to leave a preset time as it is, simply press PROG to
move to the next setting.
If you want to return the unit to RUN, press PROG and hold until
the colon in the display blinks. Alternatively leave alone and the
unit will automatically return to RUN after 2 minutes.
Your installer will have set your unit to programme 6, 4 or 2 events
per day. This will determine the number of events per day that you
are able to programme.
Changing the preset programmes in 5/2 day mode
For Days 1-5 (weekdays)
a) Press PROG until the rst preset time and
temperature (Event 1 Days 1, 2, 3, 4, 5) appears
in display.
b) Use the +and -buttons to adjust the TIME
(press and hold to change in 10 minute increments).
c) Use the Λand Vbuttons to adjust the required TEMPERATURE.

6
User Instructions
GB d) Press PROG to move to the next preset time
and temperature (Event 2).
e) Repeat steps b, c, & d to programme the
remaining weekday events.
For Days 6-7 (weekends)
Press PROG until the rst preset time and
temperature (Event 1 Days 6-7) appears in display.
Repeat steps b, c, & d above to programme the
remaining weekend events.
Changing the preset programmes in 24 hour mode
a) Press PROG until the rst preset time and
temperature (Event 1 for all days of the week)
appears in display.
b) Use the +and -buttons to adjust the TIME
(press and hold to change in 10 min increments).
c) Use the Λand Vbuttons to adjust the required
TEMPERATURE.
d) Press PROG to move to the next preset time
and temperature (Event 2).
e) Repeat steps b, c, & d to programme the remaining events.
Changing preset programmes for AB programming
(Installer setting must be in 5/2 day mode)
Press and hold PROG and Vfor 3 seconds. The
display will change to the gure opposite. This
will take you into User Advanced Programming
option 1.
Use Λand Vkeys to enable or disable the function
(1=enabled, 0=disabled).
Press PROG for 5 seconds until the display changes
and the colon in the display ashes to conrm that
you are in RUN.
Press PROG once, the display will change to show
the default days assigned to programme “A” (days
1, 2, 3, 4 & 5).

7
Use the +and -keys to scroll forwards or backwards
through the days of the week.
To deselect a day press V, (for example Day 2). To
select a day press Λ(for example Day 7).
Any deselected days are automatically assigned to programme“B”.
Programming“A”programme days and events
a) Press PROG until the rst preset time and
temperature (Event 1 for Programme A)
appears in display.
b) Use the +and -buttons to adjust the TIME
(press and hold to change in 10 minute increments).
c) Use the Λand Vbuttons to adjust the required TEMPERATURE.
d) Press PROG to move to the next preset time and temperature
(Event 2).
e) Repeat steps b, c, & d to programme the remaining events.
Programming“B”programme days and events
a) Press PROG until the rst preset time and
temperature (Event 1 for Programme B)
appears in the display.
b) Use the +and -buttons to adjust the TIME
(press and hold to change in 10 minute increments).
c) Use the Λand Vbuttons to adjust the required TEMPERATURE.
d) Press PROG to move to the next preset time and temperature
(Event 2).
e) Repeat steps b, c, & d to programme the remaining events.
Running the programme
Press PROG to return to RUN, the colon in the
display will blink. The heating will now follow the
times and temperatures programmed.
User Instructions
GB

8
User Instructions
GB User Overrides
Altering the display to show time or temperature
Press +and -together to
change between settings.
Temporarily alter current programmed temperature
Press Λor Vuntil required temperature is displayed. Please note that
your installer may have restricted both upper and lower temperature
settings and the temperature override limits.
This override will automatically be cancelled at the beginning of the next
programmed event. Please note that your installer may have restricted
the duration of the override to something other than next event.
To change day of week legends from numbers to text
Press Λand -together to toggle between day numbers and text.
To change time display between 12 & 24 hour clock
Press Λand +together to toggle between 12 and 24 hour clock.
To change between °C and °F scaling
Press Vand -together to toggle between °C and °F temperature
scaling.
Thermostat mode
a) A constant temperature of between 5-30°C can be selected if
required. This can provide frost protection for periods away from
home, it can also be used to provide untimed higher temperatures
if, for example, a family member is sick.

9
User Instructions
GB
b) Press Λand Vtogether to enter thermostat mode. The default
setting is 8°C, but this can be reprogrammed, see User Advanced
Programming, step 10, (page 11).
c) A snowake symbol will appear in the display
when the selected temperature is equal to or less
than the programmed frost protection setting.
d) Use the Λor Vbuttons to change the
temperature away from the programmed frost protection
temperature to another value.
e) To return to automatic programming press both Λand Vtogether.
Changing the clock forwards and backwards
This is handled automatically, however, if the manual changeover has
been selected follow the instructions below.
To change from Summer to Winter (clocks back)
Press and hold -button.
To change from Winter to Summer (clocks forward)
Press and hold +button.
Remote override into and out of thermostat mode
Selected models are available with a feature which allows a telephone
activated switch or window contacts to step the unit into or out of
thermostat mode.
The required temperature to be maintained when the building is
unoccupied, or when windows are open, must rst be set up in User
Advanced Programming, step 10, (page 11).
To locally override this feature press both Λand Vtogether.
Delay start feature
Your thermostat includes an optional delay start feature to hold o
the heating for a time on mild days when the room temperature at the
start of an event is close to the programmed value. If you have enabled
this function it can be overridden by pressing either Λor Vbuttons.
To enable this feature, please refer to User Advanced Programming,
step 11, (page 12).

10
User Instructions
GB Optimum start control (OSC)
Your thermostat includes an optional optimum start control. This
feature allows you to set the time at which you require a room
temperature by. The thermostat then calculates how soon before the
event time the system must be turned up to ensure that the room is at
the temperature by the required time. A full description of this and how
to enable it and set it up is given in User Advanced Programming,
steps 12 & 13, (page 12 and 13).
Battery replacement (battery models only)
When batteries are low a battery symbol will
appear on the display. You have 15 days to replace
the batteries before the unit shuts down. When
replacing batteries ensure that only high quality
alkaline cells are use.
IMPORTANT: After replacing the batteries press and release the RESET
button to restart the unit. All date, time, programming and override
settings are maintained for the life of the product.
User Advanced Programming
Options
Important: The thermostat has been set in the factory to suit most
situations, however, there are additional optional settings which can
improve the comfort, convenience and energy eectiveness of your
thermostat. These are set in the User Advanced Programming and
Installer Advanced Programming modes.
To access User Advanced Programming
Press and hold V and PROG for 3 seconds. This will take you into
User Advanced Programming. Use +and -keys to scroll backwards
and forwards between options then Λand Vkeys to change option
settings. The ashing digit on the right hand of the display indicates
the number of the selected option.