Danfoss TP7000-RF Wiring diagram

TP7000 + RF
GB Installation Instructions
User Instructions
Instructions d’installation
Instructions d’utilisateur
Installationsanweisungen
Inbetriebnahme-Instruktion
Instrucciones de instalación
Instrucciones del usuario
Instruktions vejledning
Brugervejleding
Electronic 7 day programmable room thermostat
Installatie handleiding
Instructies voor Gebruik
Ïäçãßåò åãêáôÜóôáóçò
Ïäçãßåò ÷ñÞóçò
Instrukcja instalacji
Instrukcja Użytkownika
Montavimo instrukcijos
Informacija Vartotojui
Istruzioni per l’uso
Istruzioni per l’utente
F
D
ES
DK
NL
GR
PL
LT
I
®
Certification Mark

2
INDEX
Installation Instructions 3-6
User Instructions 7-13
Instructions d’installation 14-17
Instructions d’utilisateur 18-23
Installationsanweisungen 24-27
Inbetriebnahme-Instruktion 28-33
Instrucciones de instalación 34-37
Instrucciones del usuario 38-43
Instruktions vejledning 44-47
Brugervejleding 48-53
Installatie handleiding 54-57
Instructies voor Gebruik 58-63
Ïäçãßåò åãêáôÜóôáóçò 64-67
Ïäçãßåò ÷ñÞóçò 68-73
Instrukcja instalacji 74-77
Instrukcja Użytkownika 78-83
Montavimo instrukcijos 84-87
Informacija Vartotojui 88-93
Instruzioni per l’uso 94-97
Instruzioni per l’utente 98-103
GB
F
D
ES
DK
NL
GR
PL
LT
I

3
Thermostat Features TP7000-RF TP7000
TP7000A
TP7000-M
TP7000-MA TP7000-M 24
Power supply 2 x AA/MN1500/LR6
alkaline batteries 230v, 50 Hz 24v, 50 Hz
Memory backup
Capacitor during
battery change for 1
minute
Rechargable cell, 24 hrs (*1)
Switching action of output relay N/A 1 x SPDT, Type 1B
Switch rating of relay contact,
voltage and current N/A 3(1) A, 10-230 volts
Transmitter frequency (RF only) 433.92 MHz N/A
Transmitter range (RF only) 30m max. N/A
Rated Impulse Voltage N/A 2.5Kv
Dimensions (mm) 138 wide x 88 high x 28 deep
Ball Pressure Test 75°C
Temperature Range 5-30°C
Design Standard EN 60730-2-7 (EN300220 for RF)
Control Pollution Situation Degree 2
Time accuracy ± 1 min.
Temperature accuracy ±1°C
*1: Unit must powered up for 6 days to charge cell before full back-up is available
Installation Instructions
Important noteRFproducts: Ensurethatthere arenolargemetalobjects,
such as boiler cases or other large appliances, in line of sight between the
transmitter and receiver as these will prevent communication between
thermostat and receiver.
Specication
Installation Instructions
Please Note:
This product should only be installed by a qualied electrician
or competent heating installer and should be in accordance with
the current edition of the IEEE wiring regulations.
GB

4
All models
Sw 15/2 day programming 7 day programming
Sw 2Optimum start contoller enabled Optimum start contoller disabled
Sw 3Chrono-proportional control On/O control
TP7000, M, & RF models with 3/6 cycles per hour option
Sw 4Chrono-proportional, 6 cycles / hour Chrono-proportional, 3 cycles / hour
Installation
DIL Switch Settings
 First remove the wallplate from the back of the unit.
 From the top left hand corner of the wallplate, there must be
clearances of at least 140mm to the right, 15mm to the left, 30mm
above and 100mm below in order to mount the plug-in module.
 Before mounting the unit ensure the 4 DIL switches on the rear of the
unit have been moved to the required settings (see below). Factory
preset is 7-day, with Optimum Start and Chrono-proportional
control OFF.
NOTE
Use Chrono 3 for high thermal inertia systems, e.g. oor standing cast iron boilers.
Use Chrono 6 for low thermal inertia systems, e.g. low water content boilers and combi
boilers.
Installation Instructions
GB

5
TP7000 Wiring (not RF models)
7-day - each day can be programmed with dierent times and
temperatures.
5/2 day - one set of times & temperatures for weekdays, and another
set for weekends.
Optimum start control - function which switches the heating on
earlier than the Event 1 programmed time to ensure the required
temperature is achieved by the set time.
Chrono-proportional control - energy saving feature which res the
boiler at regular intervals to maintain a set temperature, achieving a
constant ambient environment for the user.
Setting Optimum Start Control
-4˚C
-3˚C
-2˚C
-1˚C
A
B
C
120
min.
90
min.
60
min.
30
min.
Event
time
(
D
 Set Sw2 to OSC ON
(see DIL settings page 4)
 Select OPTIMISER CURVE in
programming mode
A Event 1 Set Point
BDeviation from Set Point
CSwitch On Time prior to Event
DOptimiser Curve Setting
1234567
ELECTRONICS
REMOTE
SENSOR
'A' models
only
COM ON OFF
Installation Instructions
GB
BC
M 24V models onl
y
24V
LN
M 230V models onl
230V
Note: 1.0mm2solid copper cable should be used to connect the remote
sensor to the TP7000A. Please ensure that:
a) the cable length does not exceed 50 metres,
b) to avoid electrical interference the cable should not be run parallel
in close proximity to other cables carrying mains electricity, and where
necessary the cable should cross over mains cabling at right angles.

6
1. TP7000-RF
Press the recessed RESET button, using a non-
metallic object, to reset the unit.
2. Press & hold the recessed LEARN button for 3
seconds, using a non-metallic object.
NOTE: Thermostat now transmits continuously for 5 mins.
3. RX1 - Press and hold buttons PROG and CH1 for
3 seconds until green light ashes once.
4. RX2 (if applicable)
Stat 1 - perform steps 1-3.
Stat 2 - wait 5 mins, perform steps1-2 and then press PROG and CH2
on RX2.
RX3 (if applicable)
Stat 1 - perform steps 1 – 3.
Stat 2 - wait 5 mins, perform steps 1-2 and then press PROG and CH2
on RX3.
Stat 3 - wait 5 mins, perform steps 1-2 and then press PROG and CH3
on RX3.
5. TP7000-RF - Press or  to return the unit to
normal operation.
Commissioning (RF versions only)
If the thermostat and the receiver have been supplied together in
a combined pack, the units have been paired in the factory and no
commissioning is required (RX1 only).
To tune the RX receiver to the frequency of the thermostat signal, follow
steps 1-5 below.
RX1
LEARN
RESET
Receiver Wiring (RF models only)
1234
ELECTRONICS
NL
COM ZONE
1 ON
ZONE
1 OFF
A
ELECTRONICS
BC123456
NLZONE
1 ON
ZONE
1 OFF
ZONE
2 ON
ZONE
3 ON
COM
TERMINAL 6
RX3 ONLY
RX1 RX2 & RX3
Note: 1) For mains voltage operated systems link terminal 2 to mains live supply.
2) Power supply to unit must not be switched by timeswitch.
Installation Instructions
GB

7
What is a programmable room thermostat?
... an explanation for householders
A programmable room thermostat is both a programmer and a room
thermostat. A programmer allows you to set ‘On’ and ‘O’ time periods
to suit your own lifestyle. A room thermostat works by sensing the air
temperature, switching on the heating when the air temperature falls below
the thermostat setting, and switching it o once this set temperature has
been reached.
So, a programmable room thermostat lets you choose what times you want
the heating to be on, and what temperature it should reach while it is on.
It will allow you to select dierent temperatures in your home at dierent
times of the day (and days of the week) to meet your particular needs.
Turning a programmable room thermostat to a higher setting will not make
the room heat up any faster. How quickly the room heats up depends on the
design of the heating system, for example, the size of boiler and radiators.
Neither does the setting aect how quickly the room cools down. Turning
a programmable room thermostat to a lower setting will result in the room
being controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to nd the
lowest temperature settings that you are comfortable with at the dierent
times you have chosen, and then leave it alone to do its job. The best way to
do this is to set low temperatures rst, say 18°C, and then turn them up by
one degree each day until you are comfortable with the temperatures. You
won’t have to adjust the thermostat further. Any adjustments above these
settings will waste energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only one
programmable room thermostat to control the whole house. But you can
have dierent temperatures in individual rooms by installing thermostatic
radiator valves (TRVs) on individual radiators. If you don’t have TRVs, you
should choose a temperature that is reasonable for the whole house. If you
do have TRVs, you can choose a slightly higher setting to make sure that
even the coldest room is comfortable, then prevent any overheating in other
rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be
adjusted in spring and autumn at the changes between Greenwich Mean
Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for example,
‘Override’, ‘Advance’ or ‘Boost’. These are explained in the manufacturer’s
instructions.
Programmable room thermostats need a free ow of air to sense the
temperature, so they must not be covered by curtains or blocked by
furniture. Nearby electric res, televisions, wall or table lamps may prevent
the thermostat from working properly.
User Instructions
GB

8
User Instructions
Your programmable room thermostat
The TP7000 allows you to programme up to 6 dierent time and
temperature settings for each day of the week, providing complete
exibility. It provides several energy saving features and features
several useful user overrides, including a 99 day holiday mode.
Preset Programmes
YourTP7000 comes ready programmed with a set of operating times and
temperatures which often suit most people.
If you want, you can change any of these settings by following the
instructions on pages 10-11. First follow the steps on page 9 to set your
display preferences and the correct time and date.
Before you start
Open the ap on the front of your
programmer. Using a non-metallic
object, press the recessed RESET
button, until you hear a click and the
display goes blank.
Weekdays (Mon-Fri) Weekend (Sat-Sun)
Event Time Temp °C Event Time Temp °C
1 06:30 20 1 07:30 20
2 08:30 15 2 09:30 20
3 11:30 20 3 11:30 20
4 13:30 15 4 13:30 20
5 16:30 21 5 16:30 21
6 22:30 15 6 22:30 15
RESET
User Instructions
GB

9
Display preferences
Temperature display (°C or °F)
Press and hold DAY & COPY (for 2-3 seconds)
until display changes.
Clock display (12 or 24 hr)
Press and hold NEXT & DAY (for 2-3 seconds)
until display change.
(AM or PM will appear in 12 hr mode)
Setting the Clock & Day
Press PROG to begin programming.
DAY - Press DAY until correct day is shown
(1=Monday, 2=Tuesday etc).
TIME - Press + and - to change time (press and
hold to change in 10 min increments).
This display will ONLY appear if the OSC function has
been enabled by your installer.
Use the + or - buttons to select the OSC
period. The choices are 0:30 (30 mins), 1:00 (1
hr), 1:30 and 2:00.
The recommended setting is 0:30. If set to
0:00 the function is disabled.
To change DAY
To change TIME
Setting the OSC Period, if enabled (see pg.5)
Accepting the preset programmes
If you are happy to use the preset programmes on page 8, you don’t
need to do anything else. To accept these settings just close the
front cover and after 2 minutes the pre-settings will automatically be
accepted.
User Instructions
GB

10
The unit is now in RUN mode (colon ashes in
display) and the heating will operate according
to the preset programmes.
a) Press PROG until Event 1 ashes, then press
DAY to move from current day to Day 1.
b) Amend the time and temperature as
follows:
i) Use + and – buttons to alter time
(press and hold to change in 10 min
increments).
ii) Use and buttons to alter
temperature in 0.5°C (1°F) steps.
iii) Press NEXT to advance to next Event.
iv) Repeat steps i,ii & iii above for Events 2,
3, 4, 5 & 6.
Programming in 7-day mode
(separate programmes for each day of the week)
1
Before you change the preset programmes
Your installer will have set your unit to operate in either 7-day mode
or 5/2 day mode. To tell which mode your unit is set press PROG until
Event 1 ashes in the display.
This unit is in 7-day mode and you can programme
dierent settings for each day of the week (see page 10-
11).
This unit is in 5/2 day mode and you can enter one of
set of programmes for weekdays and another set for
weekends (see page 11).
1
1 2 3 4 5
User Instructions
GB