Danfoss TP6000M User manual

1
User Instructions
TP6000M & TP6000MA Electronic Programmable Room Thermostats
Product Features
• 2 or 4 programmed events each day, set by installer
• 5/2 day programming, provides dierent set of
programmes for weekend
• AM/PM or 24 hour clock display set by user
• Centigrade or Fahrenheit temperature display, set by user
•Mains powered
• Factory pre-set programmes which can be edited by user
• Built-in & remote sensor versions
LCD DISPLAY
Heating Temperature
Event Number
Thermometer Mode Indicator
Temperature Override - Up
Temperature Override - Down
Thermostat Calling for Heat
Main Display
Time or Temperature
Day of week (1 = Monday)
Keyboard
Locked

2
BUTTONSLCD DISPLAYS
A) Important note; Resetting the unit - To ensure correct operation press reset button
before commencing with programming.
Important note; If no buttons are pressed for two minutes the unit will automatically go
back to run mode. All changes made will be saved.
B) USER PREFERENCES
Before programming the thermostat it is recommended that the user preferences as regards
clock display and temperature scale are set. Details of the available user preferences are shown
below:
Clock display: press both - and  buttons and hold for 2 seconds to change display between
AM/PM & 24 hour. Repeat to return to original setting.
Temperature scale: to select between centigrade and farenheit temperature displays, follow
the steps below:
1. Press - and  buttons for 2 seconds to enter temperature display mode
2. Press - and + buttons for 2 seconds to change between centrigrade and farenheit display
3.Press - and  buttons for 2 seconds to change display back to time display mode prior to
programming.
Display actual room temperature: to permanently display actual room temperature press both
- and  and hold for 2 seconds. Repeat to return to time display.
C) SETTING THE TIME OF DAY AND DAY OF WEEK
1 Press PROG button to enter programming mode.
2. Press + or – buttons to adjust time of day, if in AM/PM mode remember to ensure that AM/PM
setting is correct.
3. Press PROG to move on to select current day of week.
4. Press + or - button repeatedly until correct day of week is displayed. Day 7 is Sunday.
5. Press PROG button to advance to“Programming event times and temperatures”.
D) PROGRAMMING EVENT TIMES AND TEMPERATURES
Reminder - The thermostat can be set by the installer to provide 2 or 4 programme events per
day. The thermostat provides 5-day / 2-day Programming with one set of programmes for days
1-5, (Monday to Friday), and another set of programmes for days 6-7, (Saturday and Sunday).
Reminder - If thermostat has been set by building owner or installer for 2 events per day, only
2 events can be programmed.
Reminder – The time setting of all events are made in increments of 10 minutes.
Setting the time and temperatures events for Days 1-5.
1. Press + or – buttons to adjust event time for event 1.
-
plus 
-
plus
+
-
plus 
PROG
+-
or
PROG
+-
or
PROG
then
-
plus 
then
then
-
plus 
+-
or
RESET

3
BUTTONSLCD DISPLAYS
2. Press PROG to advance to temperature setting.
3. Press  or  buttons to adjust heating temperature
OPTIONAL: If heating is not required, “O”can be selected below 5°C.
Press PROG button to move onto event 2 programming and follow details below:
1. Press + or – buttons to adjust event time.
2. Press PROG to advance to temperature setting.
3. Press  or  buttons to adjust heating temperature
OPTIONAL: If heating is not required, “O”can be selected below 5°C.
Press PROG button to move onto next event 3 programming and follow details below:
1. Press + or – buttons to adjust event time.
2. Press PROG to advance to temperature setting.
3. Press  or  buttons to adjust heating temperature
OPTIONAL: If heating is not required, “O”can be selected below 5°C.
Press PROG button to move onto next event 4 programming and follow details below:
1. Press + or – buttons to adjust event time.
2. Press PROG to advance to temperature setting.
3. Press  or  buttons to adjust heating temperature
OPTIONAL: If heating is not required, “O”can be selected below 5°C.
Press PROG to advance to programming of days 6 & 7.
Setting the time and temperatures events for Days 6-7.
1. Press + or – buttons to adjust event time.

PROG
+-
or

or
PROG

or
PROG
+-
or
PROG

or
PROG
+-
or
PROG

or
PROG
+-
or
PROG
then
then
then
then
then
then
then

4
BUTTONSLCD DISPLAYS
2. Press PROG to advance to temperature setting.
3. Press  or  buttons to adjust heating temperature
OPTIONAL: If heating is not required, “O”can be selected below 5°C.
Press PROG button to move onto event 2 programming and follow details below.
1. Press + or – buttons to adjust event time.
2. Press PROG to advance to temperature setting.
3. Press  or  buttons to adjust heating temperature
OPTIONAL: If heating is not required, “O”can be selected below 5°C.
Press PROG button to move onto next event 3 programming and follow details below:
1. Press + or – buttons to adjust event time.
2. Press PROG to advance to temperature setting.
3. Press  or  buttons to adjust heating temperature
OPTIONAL: If heating is not required, “O”can be selected below 5°C.
Press PROG button to move onto next event 4 programming and repeat steps F1 – F3 above.
1. Press + or – buttons to adjust event time.
2. Press PROG to advance to temperature setting.
3. Press  or  buttons to adjust heating temperature
OPTIONAL: If heating is not required, “O”can be selected below 5°C.
PROG

or
then

or
PROG
+-
or
PROG
then
then

or
PROG
+-
or
PROG
then
then

or
PROG
+-
or
PROG
then
then

5
BUTTONSLCD DISPLAYS
DAILY USE INSTRUCTIONS
E) TEMPORARY CHANGES TO PROGRAMMED TEMPERATURES
Press either  or  buttons to view programmed temperatues.
Note: If O is selected this option does not operate.
Then use  button to temporarily raise temperature, a  symbol will appear in the LCD dis-
play.
Or use  button to temporarily lower temperature, a  symbol will appear in the LCD display.
Reminder - Limited temperature adjustment:The amount of temperature adjustment may have
been limited by the building owner or the installer.
Reminder - Automatic cancellation of overrides: Any temporary override of temperature is
cancelled at the next event.
F) SELECTING WEEKEND INTO WEEKDAY OVERRIDE
Week-end into week day override
To temporarily copy weekend programmes into weekdays press both  and  buttons together
and hold down for 2 seconds.
To cancel the weekend into weekday override press both  and  buttons twice.
Advice:
During weekdays, this allows weekend programmes to be temporarily be copied into the current
day. The programme reverts to normal operation at the end of the day.
G) SELECTING THERMOSTAT MODE
Thermostat mode options
Programmes can be permanently overridden by selectingTHERMOSTAT mode, this feature is used
if xed temperatures are required for extended periods of operation.
1. To enter THERMOSTAT mode press both  and  buttons together and hold down for 2
seconds to enter WEEKDAY into WEEK END override.
2. Press both  and  buttons together for a second time and hold down for 2 seconds to enter
THERMOSTAT mode. The default setting is heat only.
3. Once in THERMOSTAT mode it is possible to select the required heating temperatures and the
thermostat operating mode, see below for setting details.
4. Use  or  buttons to select required heating temperature.
Advice: THERMOSTAT mode can be cancelled at any time by pressing both and buttons
together and holding down for 2 seconds. This will return the unit to normal running mode.



and

and

or

and
then

and

6
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to
products already on order provided that such alterations can be made without subsequent changes being necessary in specications already agreed.
Part No. 33074v07 07/07
Danfoss Randall Ltd
Ampthill Road,
Bedford, MK42 9ER
Tel: [phone] Fax: [phone]
Email: [e-mail]
Website: www.danfoss-randall.co.uk
Event Setting Time/ temp Days 1-5 Days 6-7
Time: 6:30 7:30
Temp. Heat: 20.0°C 20.0°C
User Time:
Temp. Heat:
Factory Time: 8:30 9:30
Temp. Heat: 15.0°C 20.0°C
User Time:
Temp. Heat:
Factory Time: 16:30 16:30
Temp. Heat: 21.0°C 21.0°C
User Time:
Temp. Heat:
Factory Time: 22:30 22:30
Temp. Heat: 15.0°C 15.0°C
User Time:
Temp. Heat:
OTHER FEATURES AND FUNCTIONS
H) DISPLAYING ROOM TEMPERATURE
To enter thermometer mode to display current room temperature press both - and  buttons
and hold for 2 seconds. To return to time display repeat press and hold operation.
! Remember - the unit will revert to time display after Programming or Advanced Programming
Mode has been entered.
Reminder – Whilst in thermometer mode if the display ashes a row of bars the measured
temperature exceeds the display limit.
I) RESETTING THE THERMOSTAT MEMORY
Caution – Returns thermostat to factory settings: This should only be carried out should the
performance of the thermostat become erratic, this is only likely to happen as a result of severe
electro-magnetic interference such as a lightening storm.
To reset clock and re-start the thermostats micro-processor press the RESET button. After doing
this the thermostat must be re-programmed.
J) SETTING RECORD
BUTTONSLCD DISPLAYS
-
plus
RESET