Danfoss DEVIreg 130 User manual

www.DEVI.com
Installation Guide
DEVIreg™ 130
Electronic Thermostat

DEVIreg™ 130
Installation Guide2

DEVIreg™ 130
Installation Guide 3
1 Introduction
DEVIreg™ 130 is an electronic thermostat to be installed
directly on the wall. It is provided with a floor sensor to
measure and control the desired floor temperature.
The thermostat has a button for adjusting the temperature
setting with a scale from ( ) 1 to 5 (each step corresponds
to approximately 9 °C). Furthermore, the thermostat has an
LED indicator showing standby periods (green light) and
heating periods (red light).
More information on this product can also be found at:
devireg.devi.com
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specifications . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . 6
3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Temperature Settings . . . . . . . . . . . . . . 10
4 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Disposal Instruction . . . . . . . . . . . . . . . . . . 14

DEVIreg™ 130
Installation Guide4
1.1 Technical Specifications
Operation voltage 220-240V~, 50Hz
Power consumption Max 5W
Relay:
Resistive load
Inductive load
Max 16A / 3680W @ 230V
cos φ= 0.3 max 1A
Sensing units NTC 15 kOhm at 25°C
Sensing values:
0 °C
25 °C
50 °C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ± 0,2 °C
Ambient temperature 0 to +30 °C
Frost protection temperature 5 °C -
Temperature range ( ) 5–45 °C
Cable specification max 1 x 4 mm² or 2 x 2,5 mm²
Ball pressure temperature 75 °C
Pollution degree Degree 2 (domestic use)
Type 1C
Storage temperature -20 to +65 °C
IP class 30
Protection class Class II -

DEVIreg™ 130
Installation Guide 5
Dimensions 82 x 82 x 36 mm
Weight 90 g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned off
before installation.
IMPORTANT: When the thermostat is used to control a
floor heating element in connection with a wooden floor or
similar material, always use a floor sensor and never set the
maximum floor temperature to more than 35 °C.
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualified installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.

DEVIreg™ 130
Installation Guide6
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
2 Mounting Instructions
Please observe the following placement guidelines:
Place the thermostat at a suitable height on
the wall (typically 80-170cm.).
In wet rooms, place the thermostat according
to local regulation on IP classes.
Do not place the thermostat on the inner side
of an exterior wall.

DEVIreg™ 130
Installation Guide 7
• Place the floor sensor in a conduit in an
appropriate place where it is not exposed
to sunlight or draft from door openings.
• Equally distant and >2cm from two heating
cables.
• The conduit should be flush with the
floor surface - countersink the conduit if
necessary.
• Route the conduit to the connection box.
• The bending radius of the conduit must be
min 50mm.

DEVIreg™ 130
Installation Guide8
Follow the steps below to mount the thermostat:
1. Open the thermostat:
• Lift off the button using a small screwdriver.
• Loosen the screw which holds the front.
• Push down the release tab at the top of the
thermostat using a flat object while slowly pulling
off the front cover.

DEVIreg™ 130
Installation Guide 9
2. Fasten the thermostat directly to the wall by driving
the screws through the holes in each side of the
thermostat.
= Screw holes for fastening the thermostat.
3. Connect the thermostat according to the connection
diagram.
IP30
0T30
D130
NTC
1234
Sensor
Max.Load
16 (1) A
Mains
220-240V~
N
LOAD
L
LOAD
NL
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note: Always install the floor sensor in a conduit in
the floor.

DEVIreg™ 130
Installation Guide10
4. Install the front cover and button in the reverse order
of disassembly.
5. Turn on the power supply.
3 Settings
3.1 Temperature Settings
How to change the minimum and maximum floor
temperatures
1. Lift off the adjustment
button using a thin
screwdriver. 
2. Move the pins to the
desired positions.
(and ).
3. Put the adjustment button
back in place.
Please be aware of the following:
• The floor temperature is measured where the sensor
is placed.
• The temperature of the bottom of a wooden floor can
be up to 10 degrees higher than the top.
• Floor manufactures often specify the max
temperature on the top surface of the floor (usually
27-28 °C).