Danpon VH800 User manual

TECHNICAL SPECIFICATION
3
Lens type
Output Power
Wavelength
Accuracy
Angle accuracy
Angle of projection
Self-leveling range
Out of Range
Brake mode
Function
Power Supply
Duration
Operating temperature
Weight
Exterior Size
Base
: Single glass lens
: <5mw
: Line Beam - 532nm
Point - 650nm
: ±1.0mm/5M
: 90° ±0.02°
: Vertical>120°
Horizontal>100°
: ±3°
: Flashing
: Magnet
: 1 Horizontal Beam,
2 Vertical Beam,
Up dot and Down dot
: 4AA Batteries (DC6V)
: 12 hours for a single line
: 10℃~ +40℃
: 0.89 kg(excl. batteries)
: φ130x186mm
: 360° Rotary and Precise
Adjustable Aluminum
Alloy Base
MULTI-FUNCTIONAL LASER LEVEL
(1 Horizontal line+ 2 Vertical lines+ Up & Down dot)
VH800
(GREEN BEAM)
TYPE:VH800 Instruction Manual
BRIGHTER, BETTER FOR EYE VISIBILITY
Thank you for choosing our product. In order to
correctly use this product, please read the
manual carefully before use.
1
RANGE OFAPPLICATION
Suspended ceiling construction.
Partition construction.
Installation of electricity, air-conditioner
and water pipes.
Marble and floorboard paving.
OA-related office decoration and
measuring-related work where leveling
and plumbing is needed.
2
4
EXTERIOR STRUCTURE
1. Level bubble
2. Horizontal line projecting aperture
3. Vertical line projecting aperture
4. Up dot projecting aperture
5. Operating switch
6. Belt
7. Adjustable knob for line
8. Adjustable foot for bubble
9. Lock switch
10. Vertical line projecting aperture
11. Battery compartment
12. Rotary base (360°)
10
11
12
1
2
3
5
6
7
9
8
4

PACKING LIST
1. Body
2. Plastic box
3. Magnetic ceiling target
4. Glasses
5. Instruction manual
6. Receiver (Optional)
7. Tripod (Optional)
OPTIONALACCESSORY
1. Receiver
2. Tripod
6
LASER DIODE
WAVELENGTH:532-680nm
MAX. OUTPUT:＜5mw
CLASS Ⅲa LASER PRODUCT
EXTERIOR STRUCTURE
ON OFF
Lock switch open, Power on Lock switch off, Power off
5
Low Battery Indicator
Plumb dot projecting aperture
5″/8 Threaded Hole
(may install a Tripod )
Battery Cover
Operating Button
1. Horizontal
2. Horizontal +1 Vertical + Up dot & Down dot
3. 1 Vertical + Up dot & Down dot
4. 2Vertical + Up dot & Down dot
OPERATING PROCEDURE
1. Open the battery cover as indicated and
put in 4 AA rechargeable batteries.
2. Push the lock switch to the “ON” position
and then the horizontal line is projected.
3. Rotate the adjustable foot until the bubble
is centered.
4. If it is not level, the light will flash.
5. Press the roof operating button to change
the line. If the button is pressed once, the
cross line and up dot & down dot will be
projected; Press the button twice, one
vertical line and up dot & down dot will be
projected; Press the button three times,
two vertical line and up dot & down dot will
be projected.
6. After use, push the lock switch to the
“OFF” position and put it back in the
plastic box.
7. This device could be used with tripod and
mounting bracket, which could adjust
height desired.
7
WARNING
For safety use, please read the following
instructions before use the product.
！ATTENTION
1. The temperature of the external environment is too
low, please preheat; temperature is too high,
please turn off the power. Recommended
continued use of thirty minutes, rest five minutes
and then continue to use.
2. Do not disassemble the device, or it will affect its
accuracy and function.
3. Do not put it in the humid, hot, vibrating or dusty
area.
4. Do check whether the bubble is centered.
5. Do check whether the batteries are correctly put in,
and take them out after use.
6. Do turn off the device when moving it or undesired
effects might occur.
7. Never point the laser beam into the eyes, or eye
injury might result in. This product belongs to class
Ⅲa and is safe to use.
8. Do turn off the device after use and check if the
lock switch is tightened.
9. Do not touch the beam source with your hands and
wash your hands with soft cloth if so.
10.Do move the device carefully when it is in transit, or
damage might result in.
8