Dantherm Flexibox 460 User manual

Flexibox 460 / 810
Quick setup guide
Rev. 1.1

2
This installation manual and the product use various displays and labels to ensure safe use. Ig-
noring these displays and labels and incorrectly using the product could have results as classied
below. Please read the following warning symbol information before reading the rest of this sec-
tion, and be sure to strictly observe all instructions.
Warning Not following these instructions could result in death or serious injury
Caution Not following these instructions could result in injury or property da-
mage.
The symbol means something that should NOT be done
Project safety is your responsibility!
Follow the instructions in this manual regarding the installation method and installation orienta-
tion. Not following these instructions could result in injury, death, or damage to equipment.
All work should be performed by qualied personal using safe work practices.
All proper personal protective equipment should be used. PPE required for this installation inclu-
des but is not limited to:
• Safety glasses
• Hard hat
• Safety shoes
• Hearing protection
• Cut resistant gloves
• Face shield
• Proper work attire (long sleeve shirt and long pants)
Please strictly observe the following: Special Skill is required to install the Dantherm Flexibox
units. Non-qualied personnel should not attempt any of the actions shown in this installation
guide. Dantherm shall not be responsible for improper installation or any accidents, damage, or
injury resulting from improper installation.
Warnings
Warning
Caution
Warning
Caution

3
1x
1x ~
1x
2x
1x
1x
5 mm
8 mm
4 mm
3 mm
2 mm
Tools needed

4
Product dimension
460 / 810
455 mm
18 inch 472 mm
18,6 inch
758 mm
29,9 inch
500 mm
19,7 inch
503 mm
19,7 inch
Product overview
indoor view
Earth connection
Main PCB with connections
Incoming air ow Incoming air ow

5
Product overview
Exploded
Intregreted rainhoodfan/controller
Filter Filter lock
Airow
outside air inlet
Shelter air supply
Safety grill
front
Installation bracket
Incoming air ow
460 versus 810
Flexibox 460 Flexibox 810
100mm
85mm
225 mm
225 mm

6
Prepare unit
Cut hole
minimum
900mm
(35,5 inch)
225 mm
(8,9 inch)
430 mm
(17 inch)
1
40mm
3 2
8mm
4mm
3mm
8mm
4mm
3mm
Warning
Caution

7
Mount bracket
Mount unit
Center
8 mm
4 mm
3 mm
2x
2x
8 mm
4 mm
3 mm
1/3
2/3
3/3
Center
10mm
10mm
2x

8
Seal unit
Mount damper
Flexibox dampers
Quick setup guide
Rev. 1.0

9
Mount indoor
sensor
Connect earth
Keep clear
To shelter earth

10
J5
J9
J4
J16
J17
J6
J11
J10
J15
J7
J3
J2
AL 1
AL 2
AC 1
AC 2
RS485 in
RS485 out
TTL
Gnd
Room sensor
Ext. damper GND
Ext. damper close
Ext. damper open
SD reader
48V DC negative
48V DC positive +
48V DC -16A fused
2,5 mm2 wires (AWG 13)
External safety breaker
10A Mini blade terminal.
FX ”Littlefuse” type ”997 010”
10A Mini blade terminal.
FX ”Littlefuse” type ”997 010”
10A Mini blade terminal.
FX ”Littlefuse” type ”997 010”
F2
F3
F4
3x0,75¤mm
AWG 18
Belimo LM72
4
5
4
1
4
5
4
3
4
5
4
2
NOT included
NOT included
1m
3x0,75¤mm
WhiteBlack
124
5 4 3
White
Red
-
1
2
2
1
2x2,5¤mm
AWG 13
Mandatory connections
48V DC supply
Indoor sensor
Damper
(if motorized)
Warning
Caution
power on ............................................................LED on=fan on
boot=120 sec