Darfon VOTANI User manual

49.Y2301.021 USER MANUAL VOTANI X1 YTFR06
Format148x210mm
Paper封面 300P 銅西卡單面霧 P,內頁 64 頁(4 頁空白頁)
Bindingsaddle stitching
ColorsWhite
Pages64pages

User Manual

3
Contents
Picture of the bike
Before cycling on the E-bike
Adjusting the handlebar
Adjusting the saddle
Light
Battery Operation
Controlling of Display
Front Motor Series
Middle Motor Series
P. 4
P. 6
P. 7
P. 8
P. 8
P. 9
P.13
P.27

English
4
Picture of Bike
Front Moter Series
Display
MotorSensor
ControlllerBattery

5
English
Picture of Bike
Middle Moter Series
DisplayBattery
Motor / Controller / Sensor

English
6
Dear customer
We congratulate you on the purchase of this Votani electric cycle.
This manual will explain how to use your Votani electric cycle. We strongly advise you to
read this manual carefully, so you can enjoy your Votani as long as possible. In this manual
you will nd the most important tips for your Votani with pedal support, its control and its
use. In the back of the manual you can nd an explana on on what to do in case you need
a guarantee and service. If you have any quesions or remarks after reading this manual,
feel free to contact your dealer. We wish you a lot of cycling enjoyment and many safe
kilometres on your new Votani.
We advise you to nd enough space and time before you use an electric cycle for the rst
time. Please be careful, read all instructions and check the condition of all parts. An electric
cycle reacts more quickly when it is active than a cycle without support. Please do not pedal
fast while starting. Your cycle will accelerate when the support is switched on. At rst you
will need to get used to this. When you brake, use the rear brake rst. This will immediately
interrupt the engine support. The front brake is more powerful. The support will stop when
speed of 25 km/h is reached. The support will stop when you stop pedaling; there will be a
slight delay.
Moderate your speed on slippery roads, with snow and in rainy circumstances. Riding your
e-bike is just like any other cycle. With the Shimano gear handle
you can decide in which gear you prefer to ride. You can continue pedaling when
you change gears. You are advised to start in low gear. This will improve the range. Starting
in a high gear will be like starting a car in a high gear. In that case the engine will need more
power to get moving. Your e-bike is just like that. If you start in a higher gear, the battery will
be drained to get you moving.
Cycling on an e-blke:

7
English
We advise you to read the instruction booklet carefully, quietly and completely
before you begin cycling. Furthermore we advise you to check all parts before
you start using the cycle. Do not remove any parts. For maintenance please contact your
dealer. The dealer has all the information and skill to keep your bike on the road.
To adjust the handlebar, the handlebar stem adjuster must be lifted. This is done
by pushing the small slide up. Make sure that the handlebar is straight.
In order to adjust the tension of the quick release, turn the adjusting screw, as shown above.
Make sure that the safety mark is not exposed,
To adjust the handlebar height, use a hex key. The recommended torque is 22-25 Nm)
Riding your e-bike:
Adjusting the handlebar
It is best to shift back to gear 1 or 2 in
the low support mode (Eco). Once
you reach the desired speed, select
the support which ts your speed.
The design of the cycle is a combination of ergonomics, technology and aestheics, which
results in a unique cycling experience. The smart design, together with the chosen parts,
gives a safe cycling experience. The frame is made of aluminum (6061), it is light, but stiff
and sturdy for pleasant cycling. The top speed conforms to national legislation. The support
works up to a maximum of 25 km/h. (under normal circumstances, for a rider weighing 80
kg)

English
8
To adjust the saddle position, the saddle position be adjusted a short distance forwards or
backwards, and tilted up or down at the point where it's connected to the seat-pin.
To adjust the saddle height, the saddle should be adjusted to the right height is essential for
a comfortable ride, efcient pedaling and avoiding injury.
You can use a switch on the lamp, or use the lamp itself. The lamp is supplied with AA
batteries. (supplied)
Use the hex key to
release bolts. Adjust
saddle to fitting
height. Then make
sure that fasten the
bolts.
OFF/ ON
Move the switch
left or right
OFF/ ON
Move the switch
left or right
OFF/ ON
Move the switch
left or right
Use the hex key to
release bolts. Adjust
saddle to horizontal
position or what you
want. Then make
sure that fasten the
bolts.
Adjusting the saddle
Light

9
English
Carrier battery
A. Put the battery into cradle and push until button steady.
Tips for good care of your e-bike battery:
The battery is preferably stored in a dry place (15 C - 20 C)
Use only the charger supplied with your e-bike.
Store the charger out of reach of children.
Do not cover the charger and out charger and battery on a hard bottom (Not on
a carpet).
Make sure that no dirt or moisture contaminates the charger's plug and
connector.
Battery Operation
Make sure that both wheels turn freely when you do not brake. Check the condition of the
brakes frequently. You e-bike has been designed for cycling on a normal road. Extreme
maneuvering might damage your cycle and cause injury.
Use a damp cloth and a neutral detergent to cleanse your cycle. The e-bike parts are water-
resistant. Make sure that the cycle is not cleaned using a high pressure spray. A violent rain
shower may have the same result. Avoid lubricating too much, oil on wheels and brakes
may reduce the braking power.
Brakes
Maintenance

English
10
Battery Processing
Battery type : Sony Lithium
Power : 36V
Weight : 2.8kg
Charging cycles :1000 charges
Sleep mode
If the cycle is not in motion for approximately 10 minutes, the system will go to sleep mode
automatically. To restart, switch off and on again.
Please note: when in sleep mode, there is still some energy in the system. To switch
everything off completely can help to save battery energy
Battery LED Indicator
81%~100%
61%~80%
41%~60%
21%~40%
11%~20%
1%~10%
0%
Battery is charged and operational
Indication of battery charge.
Each indication is approximately
20%
Battery is 11~20%
Battery is almost empty.
Charge your battery
Battery is completely empty.
Advice: Charge immediately!
Do not drop the charger or the battery.
Do not charge the battery in direct sunlight. (So do not put the battery near the
window.)
It is possible to charge the battery directly while it is still in the e-bike.
In that case it is absolutely necessary to switch the On/Off switch to the Off
position.
The charging process is over when all LEDs on the battery are green and the
charger shows a green indicator.
Fully charge the battery when it will not be used for a longer period of time.

11
English
• General use instructions
A. Please adjust the voltage setting depending on your
country.
B. Turn off the power before starting charging.
C. Connect the cable from charger to battery, and then insert the plug
Warnings
1. For convenience and safety, please separate thebattery with the frame while
you are charging it.
2. The input condition is acceptable for AC 115 / 230V (50 ~ 60Hz), and output
condition is DC 36V with maximum current 4 A.
3. The charger should be used indoor and kept away from any heat source.
4. Please don’t cover with anything while the charging is on progress, otherwise it
may cause re accident.
5. Please don’t charge with unspecied or bad battery.
Battery Charger
B
C
A230V
115V

English
12
D. While the charger starts charging, the led shows yellow color.
E. While the charger nishes charging, the led shows green
color.
Charging time:
The charging time depends on the remaining energy in the battery and the charger current.
If the battery is completely exhausted you can make this calculation: For example:
Battery is 8.8 Ah and the charger is 2A --> 8.8 : 2 = 4.4 hours
Battery is 13.2 Ah and the charger is 4A --> 13.2 : 4 = 3.3 hours
We advise you to exhaust the battery charge completely in the rst three times, and to charge
completely a terwards.
If you do not use the cycle often:
Charge the battery at least once a month.
(also for guarantee)
E
D

13
English
Controlling of Display
Front Motor Series
Appearance description
a. Speed - Display of current speed, and precision is decimal point one.
b. Backlight switch - Control the display backlight.
c. Time - Show riding time.
d. Message - Show error message. (Please refer to the appendix 2.3.2)
e. Distance unit - Units can be selected to "km" or "mile".
0 : No assistance, as normal bike.
1 : Minimal assistance level.
6 : Maximum assistance level.
f. Assistance level
Level
1
2
3
4
5
6
KM Mile
Distance km mile
Speed km/h mph
km
ODO
34567.8
20:37:4
3
12.
Km/h
Connect fail !
Backlight switch
Batterycapacity
Assistance level
Information option
Time
Message Speed
Distance unit

English
14
g. Information option
h. Battery capacity
Info. Description Unit
ODO
Trip
Avg
RPM
Range
Total accumulated distance.
This value is always kept.
Trip distance.
Average speed of the trip
Pedal rotations per minute
Estimated remaining range.
km or mile
km or mile
RPM
km / hr
mile / hr
km or mile
The remaining capacity (%)
and the ashing light display
96% ~ 100% Fully charged.
Energy is abundant.
Each level stand for 20%
battery capacity.
Battery capacity is about 5%
when the battery light ashes.
No assistance, please charge
immediately.
81% ~ 95%
1% ~ 5%
0%
61% ~ 80% 41% ~ 60%
21% ~ 40% 6% ~ 20%
Description

15
English
Keys :
Function key description
a. Power
● Press and hold [ ] for 1.5 seconds, power will be turned on.
● When power is on, press and hold [ ] for 2 seconds, power will be turned off.
b. Backlight switch
● When power is turned on, press [ ], display backlight will be turned on.
● Press [ ] again, and backlight will be turned off.
c. Information selection
● Press [ ] to select information.
d. Assistance model setting
● Press [ ] or [ ] to select assistance levels.
* [ ] : increase, [ ] : decrease.
e. Function setting
● Press [ ] for 1.5 seconds, then it will enter function selection.

English
16
Operation
Normal function
a. Turn On / Turn Off
Note. In order to save battery power, system will turn off automatically after stand
by over 3 minutes.
Make sure the battery is installed, and
then press [ ] for 1.5 second, it will
turn on the power.
When the power is turned on, press
and hold [ ] for 2 seconds to shut
down system. It will show "Good bye"
and then turn off.
EXCIMER
Good bye !

17
English
Note. If you want to cancel the pin enabled function, please refer to
section (ii.d.).
If pin lock function is enabled, as
shown in the picture, then it needs to
enter the password when power is
turned on.
If the password is wrong, it will display
"Pin error !" and require user to enter
pin number again.
If the password is correct, then the
system is unlocked successfully.
b. Pin enable
Meter Lock
00 0 0
Input pi n:
Pin error!
ODO
34567.8
20:37:4 km
2
00.
Km /h

English
18
When power is turned on, press [ ],
then display backlight symbol will be
shown and backlight is on.
Press [ ] again, then backlight symbol
will disappear, and backlight is turned off.
User can select their favorite assistant level according to their riding
conditions. Press [ ] or [ ] to select it.
c. Switch for backlight
d. Assistance level setting
km
ODO
34567.8
20:37:4
2
00.
Km /h
km
ODO
34567.8
20:37: 4
2
00.
Km /h
ODO
34567.8
20:37:4 km
2
00.
Km/ h

19
English
When power is turned on, press [ ] to select "ODO" -> "Trip"
-> "Average" -> "RPM" -> "Range".
e. Information selection
P.S. Different model will have different information selections.
km
ODO
34567.8
20:37:4
2
00.
Km
/h
ODO
34567.8
20:37: 4 km
00.
Km
/h
2Trip
00075.9
20:37:4 km
00.
Km /h
2Avg
00009.8
20:37:4
00.
Km /h
2
RPM
00000.8
20:37: 4
00.
Km /h
2
Range
00000.0
20:37: 4 km
00.
Km
/h
2