Data Video TLM-700HD User manual

7" TFT LCD Monitor
TLM-700HD
Instruction Manual
Rev 150310
www.datavideo-tek.com

2
Table of Contents
Warnings and Precautions................................................ 3
Warranty........................................................................... 5
Standard Warranty........................................................ 5
Two Year Warranty ....................................................... 5
Disposal............................................................................ 6
Packing List ...................................................................... 6
Introduction....................................................................... 6
Features ........................................................................... 7
Supported Formats........................................................... 7
Connections & Controls.................................................... 8
Front Panel ................................................................... 8
Rear Panel.................................................................. 10
Menu Options ................................................................. 11
1. Picture..................................................................... 11
2. Audio....................................................................... 11
3. Func........................................................................ 11
4. Setup ...................................................................... 12
5. Advance.................................................................. 13
Calibrating Datavideo Monitors....................................... 13
Specifications ................................................................. 14
Service & Support........................................................... 15

3
Warnings and Precautions
1. Read all of these warnings and save them for later reference.
2. Follow all warnings and instructions marked on this unit.
3. Unplug this unit from the wall outlet before cleaning. Do not use
liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The unit
may fall, causing serious damage.
6. Slots and openings on the cabinet top, back, and bottom are
provided for ventilation. To ensure safe and reliable operation of this
unit, and to protect it from overheating, do not block or cover these
openings. Do not place this unit on a bed, sofa, rug, or similar
surface, as the ventilation openings on the bottom of the cabinet will
be blocked. This unit should never be placed near or over a heat
register or radiator. This unit should not be placed in a built-in
installation unless proper ventilation is provided.
7. This product should only be operated from the type of power source
indicated on the marking label of the AC adapter. If you are not sure
of the type of power available, consult your Datavideo dealer or your
local power company.
8. Do not allow anything to rest on the power cord. Do not locate this
unit where the power cord will be walked on, rolled over, or
otherwise stressed.
9. If an extension cord must be used with this unit, make sure that the
total of the ampere ratings on the products plugged into the
extension cord do not exceed the extension cord’s rating.
10. Make sure that the total amperes of all the units that are plugged
into a single wall outlet do not exceed 15 amperes.

4
11. Never push objects of any kind into this unit through the cabinet
ventilation slots, as they may touch dangerous voltage points or
short out parts that could result in risk of fire or electric shock. Never
spill liquid of any kind onto or into this unit.
12. Except as specifically explained elsewhere in this manual, do not
attempt to service this product yourself. Opening or removing covers
that are marked “Do Not Remove” may expose you to dangerous
voltage points or other risks, and will void your warranty. Refer all
service issues to qualified service personnel.
13. Unplug this product from the wall outlet and refer to qualified service
personnel under the following conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under normal
operating conditions. Adjust only those controls that are
covered by the operating instructions in this manual; improper
adjustment of other controls may result in damage to the unit
and may often require extensive work by a qualified technician
to restore the unit to normal operation;
e. When the product has been dropped or the cabinet has been
damaged;
f. When the product exhibits a distinct change in performance,
indicating a need for service.

5
Warranty
Standard Warranty
Datavideo equipment is guaranteed against any manufacturing
defects for one year from the date of purchase.
The original purchase invoice or other documentary evidence
should be supplied at the time of any request for repair under
warranty.
Damage caused by accident, misuse, unauthorized repairs,
sand, grit or water is not covered by this warranty.
All mail or transportation costs including insurance are at the
expense of the owner.
All other claims of any nature are not covered.
Cables & batteries are not covered under warranty.
Warranty only valid within the country or region of purchase.
Your statutory rights are not affected.

Two Year Warranty
All Datavideo products purchased after 01-Oct.-2008 qualify for a
free one year extension to the standard Warranty, providing the
product is registered with Datavideo within 30 days of purchase.
For information on how to register please visit
www.datavideo-tek.com
or contact your local Datavideo office or authorized Distributors
Certain parts with limited lifetime expectancy such as LCD Panels,
DVD Drives, Hard Drives are only covered for the first 10,000
hours, or 1 year (whichever comes first).
Any second year warranty claims must be made to your local
Datavideo office or one of its authorized Distributors before the
extended warranty expires.

6
Disposal For EU Customers only - WEEE Marking
This symbol on the product indicates that it should
not be treated as household waste. It must be
handed over to the applicable take-back scheme for
the recycling of waste electrical and electronic
equipment. For more detailed information about the
recycling of this product, please contact your local
Datavideo office.
Packing List
Items Description Q’ty
1 TLM-700HD 1
2 Sunshield 1
3 Switching Adaptor DC 12V/1.5A 1
4 Instruction Manual 1
Introduction
The Datavideo TLM-700HD is a 7 Inch monitor designed for HD users
who work outdoors in the field or in a studio. The TLM-700HD can be
powered from a standard V-Mount battery connection or mains power.
This enables you to power the monitor using an existing camera battery
from a range of manufacturers. Its case design is both rugged and easy
to carry with a variety of features and connections that make it perfect for
set up tests and field or studio monitoring.

7
Features
7" 16:9 Wide Screen Panel
Resolution: 800 x 480 dots
View Angle (V)+60/-40°, (H)+60/-60°
HD/SD-SDI, YUV, HD-YUV, HDMI & CV Input
Internal colour bar
Blue only function
Audio indicator for SDI, HDMI
Safe Area indicator
VITC time code display
Dual colour tally light indicator
Brightness, Contrast, Colour, Tint Adjustable
Colour Temp* adjustable
Audio Level indicators
NTSC / PAL Auto Switching
4:3 / 15:9 / 16:9 switchable
* can be set to 9300, 7500, 6500, 5400 or USER RGB values.
Supported Formats
• HDMI YUV
- 720 x 576i x 50 Hz
- 720 x 480i x 60 Hz
- 1280 x 720p x 50 Hz
- 1280 x 720p x 60 Hz
- 1920 x 1080i x 50 Hz
- 1920 x 1080i x 60 Hz
• HDMI RGB
- 720 x 576i x 50 Hz
- 720 x 480i x 60 Hz
- 1280 x 720p x 50 Hz
- 1280 x 720p x 60 Hz
- 1920 x 1080i x 50 Hz
- 1920 x 1080i x 60 Hz
• SDI
- 720 x 576i / 50 Hz
- 720 x 480i / 60 Hz
- 1280 x 720p / 60 Hz
- 1280 x 720p / 50 Hz
- 1920 x 1080i / 50 Hz
- 1920 x 1080i / 60 Hz
• YUV
- 720 x 576i x 50 Hz
- 720 x 480i x 60 Hz
- 1280 x 720p x 50 Hz
- 1280 x 720p x 60 Hz
- 1920 x 1080i x 50 Hz
- 1920 x 1080i x 60 Hz
• CV
- 720 x 576i (PAL)
- 720 x 480i (NTSC)

8
Connections & Controls
Front Panel
Power Switch
Switches the power On / Off.
Stereo Headphone Mini Jack socket
The level is adjusted by headphone volume control.
Listen to embedded audio from HDMI or SDI sources.
Headphone Volume Control
Allow you to adjust the headphone volume.
Source Button
Select Input source between SDI, YPbPr, CVBS, and HDMI.
Aspect Ratio Button
Sets the LCD aspect ratio to 4.3, 15:9, or 16:9
PATTERN
The PATTERN button will generate colour bars on the
screen. Press the PATTERN button again to return normal

9
output.
BLUE
Press this button to eliminate the red and green component
of input signals. Only the blue component of an input is
displayed on the screen. This allows adjustments of chroma
and phase.
(Phase adjustment is effective with NTSC signals).
MENU
Calls up the on-screen adjustment menu (See Menu
Options for more details).
UP / DOWN
Navigate the on-screen menu and set the functions & levels.
ENTER
Confirms the new settings or return to the default state.

10
Rear Panel
HD/SD - SDI input
BNC connector for SDI Input.
YUV input
BNC connectors for analogue (Component) video inputs.
Composite video input
BNC connectors for analog (Composite) video inputs.
HDMI in interface
HDMI digital signal input connecter.
Supports HDMI 1.1
Tally In
Send in red and yellow colour tally signal to tally LED. Red
means on-air, yellow means standby.
DC in socket
Connect the supplied 12V 1.5A PSU to this socket. The
connection can be secured by screwing the outer fastening
ring of the DC In plug to the socket.

11
Menu Options
1. Picture
- Press the MENU button once to display the Picture setting menu.
- Press the ENTER button to highlight the Brightness setting.
- Press the UP or DOWN button to highlight the setting that needs to be adjusted.
- Press ENTER button to select the Brightness setting.
- Press the UP or DOWN button to adjust the Brightness value between 0 and
100.
- Press ENTER button again to save and return to the Picture setting menu; now
highlight another Picture setting to be adjusted. To select a different setting
(Contrast, Saturation, Tint, Color Temp*) use the UP / DOWN buttons.
Follow the same procedure to set the other values.
- Keep pressing the MENU button to cycle through the main menu options.
- Press the SOURCE button to exit the menu mode.
* NB: Color Temp can be set to 9300, 7500, 6500, 5400 or USER RGB values.
2. Audio
- Press the MENU button twice to display the Audio setting menu.
- Press the ENTER button to highlight the Indicator setting.
- Press the ENTER button again to toggle the on screen audio indicator ON/OFF.
- Keep pressing the MENU button to cycle through the main menu options.
- Press the SOURCE button to exit the menu mode.
3. Function.
- Press the MENU button three times to display the Function. Settings menu.
- Press the ENTER button to highlight the Center Mark setting.
- Press the ENTER button to toggle the on screen Center Mark ON/OFF.
- Press the UP or DOWN button to highlight the Safety Zone setting.
- Keep pressing the ENTER button to cycle through the values 80%, 90% or OFF.
- Press the UP or DOWN button to exit the Safety Zone setting. To select a
different setting (4:3 Screen, Cinema Zone) use the UP or DOWN buttons.
Follow the same procedure to set the next setting.
- Keep pressing the MENU button to cycle through the main menu options.
- Press the SOURCE button to exit the menu mode.

12
4. Setup
- Press the MENU button four times to display the Setup setting menu.
- Press the ENTER button to highlight the OSD Timer setting.
NB: OSD Timer sets how long the setting menus will stay on screen.
- Press the ENTER button again to display the OSD Timer setting position.
- Press the UP or DOWN button to set the OSD value between 5 to 60 SEC.
- Press ENTER button to save the OSD value.
- Press the UP or DOWN button to highlight the OSD Blending setting.
NB: OSD Blending sets how transparent the setting menus will be on screen.
- Press the ENTER button to display the OSD Blending setting position.
- Press the UP or DOWN button to select the OSD blending value (from 0~7).
NB: OSD Blending value 0 = Min transparency 7 = Max transparency
- Press the ENTER button to save the OSD blending value.
- Press the UP or DOWN button to highlight the Time Code setting.
- Press the ENTER button to toggle the on screen Time Code display ON/OFF.
- Press the UP or DOWN button to highlight the TC Position setting.
NB: TC Position is used to set where on the monitor Time Code will be shown.
- Press the ENTER button to cycle through the possible Time Code Positions on
the monitor (Left/Up, Middle/Down, Right/Down, Right/Up)
- Press the UP or DOWN button to highlight the TC HD Line setting.
- Press ENTER button to cycle through the possible HD time code lines (8~20).
- Press the UP or DOWN button to highlight the TC SD Line setting.
- Press ENTER button to cycle through the possible SD time code lines (10~21).
- Press the UP or DOWN button to highlight the TC Font Size setting.
- Press ENTER button to cycle through the possible time code font sizes on the
screen (Large or Small).
- Keep pressing the MENU button to cycle through the main menu options.
- Press the SOURCE button to exit the menu mode.

13
5. Advance
- Press the MENU button five times to display the Advance setting menu.
- Press the ENTER button to highlight the LCD L/R Scan setting.
NB: The LCD L/R Scan will reverse the image displayed horizontally.
- Press the ENTER button, the screen image will be reversed (Left to Right).
- Press the ENTER button again, the screen image will return to normal view.
- Press UP / DOWN button to highlight the LCD U/D Scan setting.
NB: The LCD U/D Scan will reverse the image displayed vertically.
- Press the ENTER button, the screen image will be reversed (Top to Bottom).
- Press the ENTER button again, the screen image will return to normal view.
- Press UP / DOWN button to highlight the Reset option.
NB: This option will return the monitor to the factory default settings.
- Press the ENTER button to re-start the monitor with the factory default settings.
- Press UP / DOWN button to highlight the Version setting.
- Press the ENTER button, the firmware version will be displayed on screen.
- Keep pressing the MENU button to cycle through the main menu options.
- Press the SOURCE button to exit the menu mode.
Calibrating Datavideo Monitors
Perhaps the most important way to make sure that your video really looks
as good as it can on other monitors is to monitor the video during
production with a properly calibrated monitor.
For guidance on how to calibrate a Datavideo Monitor using SMPTE
colour bars please visit our website http://www.datavideo.info/en/faq.php

14
Specifications
Interface
1x HD/SD-SDI input (SMPTE 272M-C 1.5Gbps, 270Mbps
with Embedded Audio)
1x Component Y.U.V Sony Betacam Spec
1x CV input
1x HDMI input
1x D-Sub 15 Pin Plug (Tally Light Signal)
HD/SD-SDI
Spec
SDI/HD-SDI Specifications
Standard SMPTE 259M-C (270Mbps - 525/625
Component Video) and SMPTE 292M (1.485/1.001 Gbps)
Connector BNC (IEC 169-8)
Impedance 75 Ω
Return Loss HD > 15 dB (5 MHz to 750 MHz)
> 10 dB (750 MHz to 1.5 GHz)
SD > 15 dB (5 MHz to 270 MHz)
Equalization 200 m Belden 8281 cable at 270 Mbps; 100 m
(typical) of Belden 1694A at 1.485 Gbps
CV Spec
Bandwidth: > 5.0MHz
Differential of Gain (DG) ＜3％
Differential of Phase (DP) ＜3°
S/N: > 50 dB
YUV Spec
Bandwidth: > 5.2MHz
Differential of Gain (DG) ＜3％
S/N: > 50 dB
HDMI Supports HDMI 1.1
Operating
Temperature 0°C to 40°C (32°F to 102°F)
Humidity 10% to 90% (non condensing)
Firmware SVN 1.6
Dimension &
Weight 187mm (W) x 132mm (H) x 72mm (D) / 1.2Kgs
Power DC 12V / 1.5A

15
Service & Support
It is our goal to make your products ownership a satisfying experience.
Our supporting staff is available to assist you in setting up and operating
your system. Please refer to our web site www.datavideo-tek.com for
answers to common questions, support requests or contact your local
office below.
Datavideo Global Website: www.datavideo-tek.com
Datavideo Corporation
Tel: [phone] Fax: [phone] E-Mail: [e-mail]
Datavideo Technologies Europe BV
Tel: [phone] Fax: [phone] E-Mail: [e-mail]
Datavideo UK Limited
Tel: [phone] Fax: [phone] E-Mail: [e-mail]
Datavideo Technologies Co., Ltd
Tel: [phone] Fax: [phone] E-mail: [e-mail]
Datavideo Technologies China Co., Ltd
Tel: [phone] Fax:[phone] E-mail: [e-mail]
Datavideo Technologies (S) PTE LTD
Tel: [phone] Fax: [phone] E-mail: [e-mail]
Datavideo HK Ltd
Tel: [phone] Fax: [phone] E-mail: [e-mail]
All the trademarks are the properties of their respective owners.
Datavideo Technologies Co., Ltd. All rights reserved 2018
G082060476E2