Datacom Systems 1000BT-AT-SX User manual

Warranty
Datacom Systems, Inc. (DSI) warrants that the hardware which it supplies will be free
from significant defects in materials and workmanship for a period of two years from
the date of delivery (Warranty Period), under normal use and conditions. In the event
of any such defect, you can return an item of defective hardware, freight prepaid, to
DSI during the Warranty Period, and DSI will repair or replace the defective equipment
and return it to you, freight prepaid. If DSI determines that the equipment is not defec-
tive, it will return it to you, freight collect. DSI shall have no responsibility for any
deficiency resulting from accidents, misuse, modifications, power disturbances
(including use of a power supply not specified by DSI), or various other forms of dis-
aster, e.g., earthquakes, floods, etc.
PLEASE DO NOT ATTEMPT TO RETURN ANY ITEM PRIOR TO RECEIVING
A RETURN MATERIAL AUTHORIZATION (RMA) NUMBER FROM DATACOM
CUSTOMER SERVICE AT [phone]
Limitation On Liability
The warranties set forth above are exclusive and in lieu of all other warranties.
Datacom Systems, Inc. (DSI) makes no other warranties, expressed or implied, and
DSI expressly disclaims all other warranties, including but not limited to implied war-
ranties of merchantability and fitness for a particular purpose. Moreover, the provisions
set forth above state DSI’s entire responsibility and your sole and exclusive remedy
with respect to any breach of warranty or contract.
No liability for consequential damages. Under no circumstances and under no theory
of Liability shall DSI be liable for costs of procurement of substitute products or serv-
ices, lost profits, lost savings, loss of information or data, or any other special, indirect,
consequential or incidental damages, arising in any way out of the sale of, use of, or
inability to use, any DSI product or service, even if DSI has been advised of the possi-
bility of such damages.
DATACOMsystems®
1000BT-AT-SX Full-Duplex Tap
Quick Installation Guide
May 2010 Part Number: 541-0078-A.01
Copyright
Copyright ©2004-2010 by Datacom Systems, Inc. All rights reserved.
Printed in the United States of America. No part of this publication may be
reproduced, stored in a retrieval system, or transmitted, in any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, with-
out the prior written permission of Datacom Systems, Inc. To obtain this per-
mission, write to the attention of the Datacom Systems legal department at
9 Adler Drive, East Syracuse, New York 13057-1290, or call 315-463-9541.
Customer Service
This Quick Installation Guide was written to help you get to know your new
10/100/1000BT-AT-SX quickly. We would welcome any comments or sugges-
tions you may have regarding this Quick Installation Guide. Please send your
remarks and recommendations via mail, telephone, facsimile, or Internet E-mail.
Datacom Customer Service personnel are available via telephone, facsimile, and
Internet E-mail. Please leave a voice message and our Customer Service Staff will
return your call as soon as possible.
Mail: Datacom Systems, Inc.
Customer Service
9 Adler Drive
East Syracuse, NY 13057-1290
Tel: [phone]
FAX: [phone]
E-mail: [email protected]
World Wide Web — You can obtain additional information about
Datacom Systems, Inc. and its products and services from the World Wide Web
at http://www.datacomsystems.com or [email protected].
Access Your Network™
DATACOM
SYSTEMS INC
™
DATACOMsystems®
Compliance Testing
CAUTION: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
Certifications
This equipment has been tested and found to meet the radiated and conducted
emission limits for a Class B product of EN 55022 to the EMC Directive
89/336/EEC requirements.
This equipment has been tested and found to meet the immunity levels for
Class 1 tested to level 2 for EN 6100-4-2, tested to level 3 for EN 61000-4-
3, tested to level 2 for EN 61000-4-4, and tested to level 3 for EN 61000-4-
5to the EN 50082-1 requirements and meets the Class A requirements for EN
61000-3-2 and EN 61000-3-3.
This equipment has completed the Product Safety Review and found to meet the
Low Voltage Directive 72/23/EEC (1993) requirements.
6
6 Connecting a 1000BT-AT-SX to the the Network
FIGURE 2 — 1000BT-AT-SX Simple Connectivity Diagram
To connect the 1000BT-AT-SX into the network, refer to FIGURE 2 and
follow these steps:
IMPORTANT:
The maximum length of 90 meters must not be exceed-
ed between end-points.
1. Before powering the TAP, connect one of the network device cables
to the 1000BT-AT-SX RJ45 port NETWORK A connector.
2. Before powering the TAP, connect the other network device cable to
the 1000BT-AT-SX RJ45 port NETWORK B connector. Ensure link
has been established between the NETWORK A device and NET-
WORK B device.
3. Connect the Power Supply barrel connector into the POWER port of
the 1000BT-AT-SX and then plug the Power Supply into the external
power source wall receptacle. The POWER LED to the right of the RJ
connectors illuminates indicating power is on.
The Rx-A, Tx-A, Rx-B, and Tx-B LEDs illuminate as data is passed
back and forth between the NETWORK A and NETWORK B device.
4. Connect one tap cable from the 1000BT-AT-SX RJ45 port TAP A
connector into one port of the Network Analysis Tool interface card.
The TAP-A LINK LED illuminates indicating link has been established
between the TAP A connector and Network Analysis Tool interface
card.
5. Connect the other tap cable from the 1000BT-AT-SX RJ45 port TAP
B connector into the other port of the Network Analysis Tool inter-
face card. The TAP-B LINK LED illuminates indicating link has been
established between the TAP B connector and Network Analysis Tool
interface card.

1
1 What’s in the Package
1000BT-AT-SX Full-Duplex Tap
Instructions
2
2 Introduction
The 1000BT-AT-SX is a single-port full-duplex device that provides
an easy method to rapidly and effectively deploy your analysis tools
to monitor 1000 BaseT traffic between your network devices.
Typically the tap is installed on a critical 1000 BaseT link in the net-
work where monitoring and analysis capabilities are important.
1000BT-AT-SX features and benefits:
• 1000 BaseT compatible
• Full duplex monitoring
• Power fault tolerant
• Standard RJ45 and SX connectors
3
3
1000BT-AT-SX Specifications
Specification
Channel One directional 1000 BaseT Ethernet
Feature
Cable Type CAT 5E and Mulimode fiber
Port Connectivity
NETWORK A
NETWORK B
TAP A
TAP B
RJ45
RJ45
SX
SX
Distance Limit 90 meter maximum length between net-
work end-points. Tap typically 1 meter.
Power Requirements External power supply 5 VDC, 1 A
5
5 Functional Operation
Refer to FIGURE 1 for a diagram of the functional operation of the
1000BT-AT-SX.
FIGURE 1 — 1000BT-AT-SX Functional Diagram
Operating Temperature
0Oto 40OC (32Oto 104OF)
Storage Temperature
-30Oto 65OC (-22Oto 149OF)
Humidity
Less than 95OC non-condensing
Dimensions
1.10" (H) x 5.75" (W) x 5.75" (D)
(includes rack mount bracket)
28 mm (H) x 146 mm (W) x 146 mm (D)
Weight
Unit - 12 ounces; Shipping - 2 pounds
Power Supply
AC•Power Cable
4
4 Installing a 1000BT-AT-SX in an Equipment Rack
Prior to putting the 1000BT-AT-SX in a standard 19-inch rack you may
want to contact your 1000BT-AT-SX representative to discuss a rack
mount option or ...
ANSI/EIA-310-D-1992 Mounting Flange Dimensional Requirements
Dimensions are in millimeters
Three devices shown mounted in optional rack panel
In any case, a couple of equipment considerations should be noted:
• Do you have universal or wide spacing flanges?
• The 1000BT-AT-SX occupies 1 unit of space when properly fastened
in a universal flange. The 1000BT-AT-SX occupies part of 2 adjoining
units of space when improperly fastened in a wide spacing hole of a
universal or wide-space flange.
Single device shown with rack mount bracket
1000BT-AT-SX with thumbscrew bracket to mount in RMC-3 rack mount
Single-mount rack bracket option.
DATACOMsystems®1000BT-AT-SX QUICKinstall
Access Your Network™
DATACOM
SYSTEMS INC
™