Datalogic GRYPHON D Series User manual

GRYPHON


D SERIES READERS
QUICK REFERENCE
INSTALLAZIONE RAPIDA
INSTALLATION RAPIDE
SCHNELLINSTALLATION
820000733 (Rev. C)

USING GRYPHON

SERIES READERS
UK
Gryphonguns automatically scan barcodes at a distance.
Simply aim and pull the trigger. Code scanning is performed
along the center of the light bar emitted from the reading
window. This bar must cover the entire code.
Successful scanning is obtained by tilting the scanner with
respect to the barcode to avoid direct reflections which impair
the reading performance, see the figure above.
Successful reading is obtained by an audible tone plus a good-
read green spot.
I
Con le pistole Gryphonla lettura dei codici a barre avviene a
distanza: è sufficiente mirare sul codice e premere il grilletto.
La finestra anteriore proietta una banda luminosa che deve
essere centrata sul codice e attraversarlo interamente. Le
condizioni ottimali per la lettura si ottengono quando la pistola
viene usata con un'inclinazione rispetto al piano su cui si trova
il codice, così da evitare il rischio di riflessione diretta, che
potrebbe compromettere il risultato della lettura (vedi figura).
La buona lettura è segnalata da un beep sonoro e da uno spot
verde che illumina il codice.
F
Avec les pistolets Gryphon, la lecture des codes s'effectue
automatiquement et à distance. Il est suffisant de viser le
code. Le faisceau sortant de la fenêtre de lecture de l'appareil
lit le code. Ce faisceau doit être centré sur le code à barres à
lire et doit le traverser de part en part.
Pour des prestations optimales inclinez la douchette par
rapport au code à lire, afin d'éviter des réflexions directes qui
pourraient compromettre la performance de lecture (voir la
figure ci-dessus).
La lecture correcte est signalée par un beep sonore ainsi que
par un spot vert qui illumine le code lu.
D
Die GryphonLesepistolen lesen Strichcodes automatisch und
berührungslos. Es genügt auf den Code zu zielen und zu
drücken. Der Code wird mittels eines Lichtbands gelesen, der
das Gerät durch das Lesefenster verläßt. Dieses Lichtband
muß den gesamten Code möglichst in der Mitte durchqueren.
Eine optimale Lesegarantie ist gewährleistet, wenn der
Benutzer die Pistole bzgl. der Oberfläche, auf der sich der
Code befindet, etwas neigt, um eine direkte Reflexion zu
vermeiden, wie im Bild oben gezeigt wird.
Das erfolgreiche Lesen wird durch einen "Beeper" und ein
rundes grünes Licht angezeigt.
DATALOGIC S.p.A.,
Via Candini, 2
40012 - Lippo di Calderara
Bologna - Italy
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
GRYPHON D100, CCD Hand Held Reader
GRYPHON D200, CCD Hand Held Reader
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista
siguiente:
89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi
and further amendments
et ses successifs amendements
und späteren Abänderungen
y succesivas enmiendas
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità
elettromagnetica ed alla sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic
compatibility and product safety.
Basée sur la législation des Etates membres relative à la compatibilité
électromagnétique et à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf
elektromagnetische Verträglichkeit und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la
compatibilidad electromagnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con la siguientes normas:
EN 55022, August 1994: L IMITS AND METHODS OF MEASUREMENTS OF
RADIO DISTURBANCE OF INFORMATION
TECHNOLOGY EQUIPMENT
(ITE)
EN 50024, September 1998: I NFORMATION T ECHNOLOGY E QUIPMENT .
I MMUNITY CHARACTERISTICS . L IMITS AND
METHODS OF MEASUREMENTS
Lippo di Calderara, 05/02/2002
Ruggero Cacioppo
Quality Assurance Supervisor

PATENTS
This product is licensed under one or more of the following
U.S. patents:
4,282,425; 4,570,057; 4,766,300; 4,894,523; 5,021,642;
5,038,024; 5,081,343; 5,095,197; 5,144,119; 5,144,121;
5,182,441; 5,187,355; 5,187,356; 5,218,191; 5,233,172;
5,258,606 and /or 5,288,985
This product is covered by one or more of the following patents
and patent applications:
US 5,917,176; US 5,992,740; US 6,010,073;
US pat. Appl. 99US-320.643; US pat. Appl. 99US-362.988;
US pat. Appl. 98US-126.606; EP pat. Appl. 00EP-830.127;
EP pat. Appl. 00EP-830.122; EP pat. Appl. 98EP-830.336;
EP pat. Appl. 98EP-830.611; EP pat. Appl. 97EP-200.317;
EP pat. Appl. 97EP-830.408; EP pat. Appl. 96EP-830.473;
EP pat. Appl. 96EP-830.660; EP pat. Appl. 96EP-830.439
FCC COMPLIANCE
This device complies with PART 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference which
may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
LED CLASS
CLASS1 LED PRODUCT APPARECCHIO LED CLASSE 1
LED KLASSE 1 APPAREIL A LED DE CLASSE 1
EN60825-1/LED11 1996
READING DIAGRAMS
GRYPHON

D100 (STANDARD)
0 5 10 15 20 25 30 35
-15
-10
-5
0
5
10
15
D100 (STD) - Reading Zones (10° skew angle)
(cm)
CODE 39
0.13 mm
(5 mils)
EAN13 M=1
0.33 mm
(13 mils)
CODE 39
0.50 mm
(20 mils)
CODE 39
0.076 mm
(3 mils)
0.13 mm
(5 mils)
GRYPHON

D200 (PDF)
0 5 10 15 20 25 30 35
-10
-5
0
5
10
D200 (PDF) - Reading Zones (10° skew angle)
(cm)
CODE39
0.076 mm
(3 mils)
CODE39
0.13 mm
(5 mils)
EAN13 M=1
0.33 mm
(13 mils)
CODE39
0.50 mm
(20 mils)
0.13 mm
(5 mils)
0246810 12 14 16
-8
-6
-4
-2
0
2
4
6
8
(cm)
D200 (PDF) - PDF417 codes, Reading Zones (10° skew angle)
PDF417 Aspect Ratio 3:1
0.25 mm
(10mils)
0.17 mm
(6.6mils) 0.38 mm (15mils)

CONNECTIONS RS232
With the RS232 cable, this accessory device is intended to be
supplied by a UL Listed Direct Plug-in Power Unit marked
"Class 2", rated 5 V, minimum 330 mA.
PEN
With the Pen Emulation cable, this accessory device is
intended to be supplied by a UL Listed Power Unit marked
"Class 2", or an LPS power source which supplies power
directly to the reader.
WEDGE
WARRANTY
UK Datalogic warranties this product against defects in
workmanship and materials, for a period of 24
months from the date of shipment, provided that the
product is operated under normal and proper
conditions.
Datalogic has the faculty to repair or replace the
product, these provisions do not prolong the original
warranty term.
The warranty does not apply to any product that has
been subject to misuse, accidental damage,
unauthorized repair or tampering.
I
Datalogic garantisce questo prodotto contro difetti di
fabbricazione e di materiali per 24 mesi dalla data di
consegna, a condizione che il prodotto sia utilizzato
come previsto.
Datalogic si riserva la facoltà di riparare o sostituire
il prodotto. Quanto sopra non prolunga la garanzia
originale.
La garanzia non si applica a prodotti utilizzati in
modo non corretto, danneggiati accidentalmente,
sottoposti a riparazioni non autorizzate o
manomessi.
F
Datalogic garantit ce produit de tout défaut de
fabrication ou des matériels pendant 24 mois de la
date de livraison, à condition que le produit soit
utlisé correctement.
Datalogic a la faculté de réparer ou de remplacer ce
produit. Ces mesures ne prolongeront pas
l’échéance de la garantie.
La garantie ne s’applique pas aux produits qui ont
été utilisés de façon incorrecte, accidentellement
endommagés, soumis à des réparations non
authorisées ou gâchés.
D
Datalogic gibt für dieses Produkt eine Garantie von
2 Jahren auf Herstellungs- und Materialfehler ab
Versandsdatum, falls das Produkt unter normalen
und angemessenen Bedingungen verwendet wurde.
Datalogic behaltet sich vor, das Produkt entweder
zu reparieren oder zu ersetzen, was aber den
originalen Garantietermin nicht verlängert.
Die Garantie ist nicht gültig, falls das Produkt falsch
angewandt, zufällig beschädigt, unberechtigt
repariert oder verändert wird.

3 OPERATING TEST
UK Read the TEST codes below.
I Leggere i codici di test.
F Lire les codes tests.
D Lesen Sie die Test-Coden.
EAN-8
1234 5670
EAN-13
1 234567 000992
Code 39 (Normal)
17162
Code 128
test
Interleaved 2 of 5
0123456784
PDF417
DATALOGIC PDF417 Test Code
WEDGE
With the Wedge or PC Notebook cables, this accessory device
is intended to be connected to either a UL Listed Computer
which supplies power directly to the reader or a UL Listed
Direct Plug-in Power Unit marked "Class 2", rated 5 V,
minimum 330 mA.
DISCONNECTING THE CABLE

TECHNICAL FEATURES
GRYPHON

D100 - D200
Electrical Features
Power Supply 5 Vdc ±5%
Consumption:
Maximum
Operating
Sleep mode
330 mA
250 mA
250 µA
Sensor CCD solid state (3648 pixels)
Max. Scan Rate 270 scans/sec
Reading Field see reading diagrams
Max. Resolution 0.076 mm (3 mils)
PCS min. 15% (Datalogic Test Chart)
Reading Indicators LED, Good Read Spot, Beeper
Environmental Features
Working Temperature 0 °C to + 55 °C
Storage Temperature -20 °C to + 70 °C
Humidity 90% non condensing
Drop Resistance IEC 68-2-32 Test ED
Protection Class IP30
Mechanical Features
Weight (without cable) about 200 g. (7 oz.)
Cable Length 2 m (6.1 ft.)
The following Keyboard Nationality selection is only valid for
IBM AT compatible PCs:
Japanese
i+'k
i+'k
i+'k
UK
YOUR READER IS NOW READY TO READ
BARCODES.
To change the defaults see the GryphonSoftware
Configuration Manual, part number 90ACC1780.
I IL LETTORE È PRONTO A LEGGERE I CODICI.
Per cambiare i parametri di default, fare riferimento
al manuale "GryphonSoftware Configuration
Manual", n. d'ordine 90ACC1780.
F VOTRE LECTEUR EST DÉSORMAIS PRÊT A
L’EMPLOI POUR LA LECTURE DE CODES.
Pour changer les paramètres voir le manuel
"GryphonSoftware Configuration Manual" numéro
d'ordre 90ACC1780.
D DAS LESEGERÄT IST JETZT BEREIT CODES ZU
LESEN.
Um die Werkseinstellungsparameter zu ändern,
schlagen Sie im Handbuch " GryphonSoftware
Configuration Manual" nach, Bestellnummer
90ACC1780.

WEDGE KEYBOARD NATIONALITY
UK Wedge users should select one of the following
WEDGE KEYBOARD NATIONALITY codes.
I Quando è selezionata l’interfaccia Wedge, leggere uno
dei seguenti codici per impostare la nazionalità della
tastiera.
F Pour l’interface Wedge, lire l'un des codes suivants
pour sélectionner la nationalité du clavier.
D Für den Betrieb mit einer Wedge-Schnittstelle lesen Sie
einen der folgenden Codes, um die Tastaturnationalität
einzustellen.
Belge
i'+k
i'+k
i'+k
Deutsch
i'+k
i'+k
i'+k
English
i'+k
i'+k
i'+k
Español
i'+k
i'+k
i'+k
Français
i'+gk
i'+gk
i'+gk
Italiano
i'+bk
i'+bk
i'+bk
Svenskt
i'+k
i'+k
i'+k
USA
i'+]k
i'+]k
i'+]k
1 DEFAULT
UK Read the RESTORE DEFAULT.
I Leggere il codice che ripristina i default.
F Lecture du code de configuration par défaut.
D Lesen Sie den Restore Default Code, um die
Werkseinstellung wieder herzustellen.
RESTORE DEFAULT
iPk
iPk
iPk
RS232 Standard DEFAULT SETTINGS
9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking,
delay disabled, rx timeout 5 sec., ack/nack disabled, FIFO
enabled, serial trigger lock disabled;
DATA FORMAT : code identifier disabled, no field adjustment,
code length not transmitted, no header, terminator = CR-LF,
character replacement disabled
RS232 Nixdorf DEFAULT SETTINGS
9600 baud, parity odd, 8 data bits, 1 stop bit, handshaking
hardware (RTS/CTS), delay disabled, rx timeout 9.9 sec.,
ack/nack disabled, FIFO enabled, serial trigger lock disabled;
DATA FORMAT : code identifier enabled, no field adjustment,
code length not transmitted, no header, terminator = CR,
character replacement disabled
RS232 Fujitsu DEFAULT SETTINGS
9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking,
delay disabled, rx timeout 2 sec., ack/nack disabled, FIFO
enabled, serial trigger lock disabled;
DATA FORMAT : code identifier enabled, no field adjustment,
code length not transmitted, no header, terminator = CR,
character replacement disabled
RS232 ICL DEFAULT SETTINGS
9600 baud, parity even, 8 data bits, 1 stop bit, handshaking
RTS always on, delay disabled, rx timeout 9.9 sec., ack/nack
disabled, FIFO enabled, serial trigger lock disabled;
DATA FORMAT : code identifier enabled, no field adjustment,
code length not transmitted, no header, terminator = CR,
character replacement disabled
WEDGE DEFAULT SETTINGS
USA keyboard, caps lock off, num lock unchanged, inter-
character and inter-code delays disabled, control character
emulation = ctrl+shift+key;

WEDGE DEFAULT SETTINGS
DATA FORMAT : code identifier disabled, no field adjustment,
code length not transmitted, no header, terminator =
ENTER, character replacement disabled
PEN EMULATION DEFAULT SETTINGS
interpret mode, conversion to code 39 disabled, output level
normal, idle level normal, minimum output pulse 600 µs,
overflow medium, inter-block delay disabled
POWER SAVE
scan rate 270 scans/s, standby disabled, sleep state
disabled, enter sleep timeout 0.6 sec
READING PARAMETERS
operating mode hand-held, trigger type = hardware, trigger
signal = level, no trigger timeout, Flash On = 1 sec, Flash
Off = .6 sec, one read per cycle, safety time .5 sec, beeper
intensity high, tone 2, beeper type monotone, beeper length
short, good read spot duration medium
DECODING PARAMETERS
ink spread enabled, overflow control enabled, interdigit
control enabled, Puzzle Solver™ disabled, decoding
safety = one read
CODE SELECTION
Enabled codes
• Code PDF417 (only GRYPHON™ D200)
• EAN 8/EAN 13 / UPC A/UPC E without ADD ON
check digit transmitted, no conversions
• Interleaved 2/5
check digit control and transmission, variable length
code; 4-99 characters
• Standard Code 39
no check digit control, variable length code; 1-99
characters
• Code 128
variable length code; 1-99 characters
Disabled codes
EAN 128, ISBT128, Code 93, Codabar,
pharmaceutical codes, Codablock-A, Codablock-F
Standard and EAN, MSI, Plessey, Telepen, Delta
IBM, Code 11, Code 16K, Code 49
ADVANCED FORMATTING PARAMETERS
concatenation disabled, no advanced formats defined
WEDGE (continued)
Wyse Terminals
ANSI Keyboard
i$1k
i$1k
i$1k
PC Keyboard
i$1Hk
i$1Hk
i$1Hk
ASCII Keyboard
i$1Ok
i$1Ok
i$1Ok
VT220 style Keyboard
i$1dk
i$1dk
i$1dk
Digital Terminals
VT2xx/VT3xx/VT4xx
i$1Vk
i$1Vk
i$1Vk
APPLE
APPLE ADB Bus
i$1]k
i$1]k
i$1]k

WEDGE (continued)
UK
The following interface selection allows barcodes
sent to the PC to be interpreted correctly
independently from the Keyboard Nationality used.
You do not need to make a Keyboard Nationality
selection.
(default = Num Lock Unchanged)
Make sure the Num Lock key on your keyboard
is ON.
I
L’impostazione del seguente tipo di interfaccia
consente una corretta interpretazione dei codici a
barre spediti al PC, indipendentemente dalla
nazionalità della tastiera utilizzata. Non è
necessario impostare la nazionalità della tastiera.
(default = Num Lock Unchanged)
Assicuratevi che la funzione BLOC NUM sulla
Vostra tastiera sia stata attivata.
F
La sélection de l’interface suivante permet une
interprétation correcte par le PC des codes à barres
transmis, indépendamment de la nationalité du
clavier. Il n’est pas necéssaire d’effectuer la
sélection de la nationalité du clavier.
(défaut = Num Lock Unchanged)
Vérifiez que le pavé numérique soit activé sur
votre clavier.
D
Die Einstellung der folgenden Schnittstellentypen
erlaubt eine korrekte Interpretation der Strichcodes,
die zum PC geschickt werden, unabhängig von der
Tastaturnationalität. Es ist nicht nötig, die
Tastaturnationalität einzustellen.
(Werkseinstellung = Num Lock Unchanged)
Bitte versichern Sie sich, daß numerische
Tastaturblock aktiviert ist.
IBM AT - ALT mode
i$1k
i$1k
i$1k
PC Notebook - ALT mode
i$1k
i$1k
i$1k
2 READER CONFIGURATION
UK Read the interface selection code for your
application.
I Leggere il codice per la selezione dell’interfaccia
relativo al modo di comunicazione desiderato.
F Lecture du code “Interface” correspondant à votre
modèle.
D Lesen Sie denjenigen Schnittstellen-Code, der
Ihrem gewünschten Kommunikationsmodus
entspricht.
RS232
Standard
i$1k
i$1k
i$1k
POS Terminals
Nixdorf Mode A
i$.k
i$.k
i$.k
Fujitsu
i$.ek
i$.ek
i$.ek
ICL Mode
i$.`k
i$.`k
i$.`k
PEN
i$1#k
i$1#k
i$1#k

WEDGE
IBM AT or PS/2 PCs
i$1Bk
i$1Bk
i$1Bk
IBM XT
i$1Wk
i$1Wk
i$1Wk
PC Notebook
i$1ek
i$1ek
i$1ek
IBM SURE1
i$1k
i$1k
i$1k
IBM Terminal 3153
i$1^k
i$1^k
i$1^k
WEDGE (continued)
IBM Terminals 31xx, 32xx, 34xx, 37xx:
UK To select the interface for these IBM Terminals,
read the correct KEY TRANSMISSION code. Select
the KEYBOARD TYPE if necessary (default =
advanced keyboard).
I Per selezionare l'interfaccia per i terminali IBM, leg-
gere il codice Key Transmission appropriato e, se
necessario, il codice Keyboard Type (default =
advanced keyboard).
F Pour selectionner l'interface pour des terminaux
IBM, lire le code de transmission du clavier (Key
Transmission Code) et, si nécessaire, aussi le code
correspondant à votre clavier (Keyboard Type Code)
(défaut = advanced keyboard).
D Um die Schnittstelle für IBM Terminals einzustellen,
lesen Sie den entsprechenden Key Transmission
Code und falls nötig den Keyboard Type Code
(Werkseinstellung = advanced keyboard).
KEY TRANSMISSION MODE
make-only keyboard
i$1Pk
i$1Pk
i$1Pk
make-break keyboard
i$1Ik
i$1Ik
i$1Ik
KEYBOARD TYPE
advanced keyboard
i',fk
i',fk
i',fk
typewriter keyboard
i',ak
i',ak
i',ak

WEDGE
IBM AT or PS/2 PCs
i$1Bk
i$1Bk
i$1Bk
IBM XT
i$1Wk
i$1Wk
i$1Wk
PC Notebook
i$1ek
i$1ek
i$1ek
IBM SURE1
i$1k
i$1k
i$1k
IBM Terminal 3153
i$1^k
i$1^k
i$1^k
WEDGE (continued)
IBM Terminals 31xx, 32xx, 34xx, 37xx:
UK To select the interface for these IBM Terminals,
read the correct KEY TRANSMISSION code. Select
the KEYBOARD TYPE if necessary (default =
advanced keyboard).
I Per selezionare l'interfaccia per i terminali IBM, leg-
gere il codice Key Transmission appropriato e, se
necessario, il codice Keyboard Type (default =
advanced keyboard).
F Pour selectionner l'interface pour des terminaux
IBM, lire le code de transmission du clavier (Key
Transmission Code) et, si nécessaire, aussi le code
correspondant à votre clavier (Keyboard Type Code)
(défaut = advanced keyboard).
D Um die Schnittstelle für IBM Terminals einzustellen,
lesen Sie den entsprechenden Key Transmission
Code und falls nötig den Keyboard Type Code
(Werkseinstellung = advanced keyboard).
KEY TRANSMISSION MODE
make-only keyboard
i$1Pk
i$1Pk
i$1Pk
make-break keyboard
i$1Ik
i$1Ik
i$1Ik
KEYBOARD TYPE
advanced keyboard
i',fk
i',fk
i',fk
typewriter keyboard
i',ak
i',ak
i',ak

WEDGE (continued)
UK
The following interface selection allows barcodes
sent to the PC to be interpreted correctly
independently from the Keyboard Nationality used.
You do not need to make a Keyboard Nationality
selection.
(default = Num Lock Unchanged)
Make sure the Num Lock key on your keyboard
is ON.
I
L’impostazione del seguente tipo di interfaccia
consente una corretta interpretazione dei codici a
barre spediti al PC, indipendentemente dalla
nazionalità della tastiera utilizzata. Non è
necessario impostare la nazionalità della tastiera.
(default = Num Lock Unchanged)
Assicuratevi che la funzione BLOC NUM sulla
Vostra tastiera sia stata attivata.
F
La sélection de l’interface suivante permet une
interprétation correcte par le PC des codes à barres
transmis, indépendamment de la nationalité du
clavier. Il n’est pas necéssaire d’effectuer la
sélection de la nationalité du clavier.
(défaut = Num Lock Unchanged)
Vérifiez que le pavé numérique soit activé sur
votre clavier.
D
Die Einstellung der folgenden Schnittstellentypen
erlaubt eine korrekte Interpretation der Strichcodes,
die zum PC geschickt werden, unabhängig von der
Tastaturnationalität. Es ist nicht nötig, die
Tastaturnationalität einzustellen.
(Werkseinstellung = Num Lock Unchanged)
Bitte versichern Sie sich, daß numerische
Tastaturblock aktiviert ist.
IBM AT - ALT mode
i$1k
i$1k
i$1k
PC Notebook - ALT mode
i$1k
i$1k
i$1k
2 READER CONFIGURATION
UK Read the interface selection code for your
application.
I Leggere il codice per la selezione dell’interfaccia
relativo al modo di comunicazione desiderato.
F Lecture du code “Interface” correspondant à votre
modèle.
D Lesen Sie denjenigen Schnittstellen-Code, der
Ihrem gewünschten Kommunikationsmodus
entspricht.
RS232
Standard
i$1k
i$1k
i$1k
POS Terminals
Nixdorf Mode A
i$.k
i$.k
i$.k
Fujitsu
i$.ek
i$.ek
i$.ek
ICL Mode
i$.`k
i$.`k
i$.`k
PEN
i$1#k
i$1#k
i$1#k

WEDGE DEFAULT SETTINGS
DATA FORMAT : code identifier disabled, no field adjustment,
code length not transmitted, no header, terminator =
ENTER, character replacement disabled
PEN EMULATION DEFAULT SETTINGS
interpret mode, conversion to code 39 disabled, output level
normal, idle level normal, minimum output pulse 600 µs,
overflow medium, inter-block delay disabled
POWER SAVE
scan rate 270 scans/s, standby disabled, sleep state
disabled, enter sleep timeout 0.6 sec
READING PARAMETERS
operating mode hand-held, trigger type = hardware, trigger
signal = level, no trigger timeout, Flash On = 1 sec, Flash
Off = .6 sec, one read per cycle, safety time .5 sec, beeper
intensity high, tone 2, beeper type monotone, beeper length
short, good read spot duration medium
DECODING PARAMETERS
ink spread enabled, overflow control enabled, interdigit
control enabled, Puzzle Solver™ disabled, decoding
safety = one read
CODE SELECTION
Enabled codes
• Code PDF417 (only GRYPHON™ D200)
• EAN 8/EAN 13 / UPC A/UPC E without ADD ON
check digit transmitted, no conversions
• Interleaved 2/5
check digit control and transmission, variable length
code; 4-99 characters
• Standard Code 39
no check digit control, variable length code; 1-99
characters
• Code 128
variable length code; 1-99 characters
Disabled codes
EAN 128, ISBT128, Code 93, Codabar,
pharmaceutical codes, Codablock-A, Codablock-F
Standard and EAN, MSI, Plessey, Telepen, Delta
IBM, Code 11, Code 16K, Code 49
ADVANCED FORMATTING PARAMETERS
concatenation disabled, no advanced formats defined
WEDGE (continued)
Wyse Terminals
ANSI Keyboard
i$1k
i$1k
i$1k
PC Keyboard
i$1Hk
i$1Hk
i$1Hk
ASCII Keyboard
i$1Ok
i$1Ok
i$1Ok
VT220 style Keyboard
i$1dk
i$1dk
i$1dk
Digital Terminals
VT2xx/VT3xx/VT4xx
i$1Vk
i$1Vk
i$1Vk
APPLE
APPLE ADB Bus
i$1]k
i$1]k
i$1]k

WEDGE KEYBOARD NATIONALITY
UK Wedge users should select one of the following
WEDGE KEYBOARD NATIONALITY codes.
I Quando è selezionata l’interfaccia Wedge, leggere uno
dei seguenti codici per impostare la nazionalità della
tastiera.
F Pour l’interface Wedge, lire l'un des codes suivants
pour sélectionner la nationalité du clavier.
D Für den Betrieb mit einer Wedge-Schnittstelle lesen Sie
einen der folgenden Codes, um die Tastaturnationalität
einzustellen.
Belge
i'+k
i'+k
i'+k
Deutsch
i'+k
i'+k
i'+k
English
i'+k
i'+k
i'+k
Español
i'+k
i'+k
i'+k
Français
i'+gk
i'+gk
i'+gk
Italiano
i'+bk
i'+bk
i'+bk
Svenskt
i'+k
i'+k
i'+k
USA
i'+]k
i'+]k
i'+]k
1 DEFAULT
UK Read the RESTORE DEFAULT.
I Leggere il codice che ripristina i default.
F Lecture du code de configuration par défaut.
D Lesen Sie den Restore Default Code, um die
Werkseinstellung wieder herzustellen.
RESTORE DEFAULT
iPk
iPk
iPk
RS232 Standard DEFAULT SETTINGS
9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking,
delay disabled, rx timeout 5 sec., ack/nack disabled, FIFO
enabled, serial trigger lock disabled;
DATA FORMAT : code identifier disabled, no field adjustment,
code length not transmitted, no header, terminator = CR-LF,
character replacement disabled
RS232 Nixdorf DEFAULT SETTINGS
9600 baud, parity odd, 8 data bits, 1 stop bit, handshaking
hardware (RTS/CTS), delay disabled, rx timeout 9.9 sec.,
ack/nack disabled, FIFO enabled, serial trigger lock disabled;
DATA FORMAT : code identifier enabled, no field adjustment,
code length not transmitted, no header, terminator = CR,
character replacement disabled
RS232 Fujitsu DEFAULT SETTINGS
9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking,
delay disabled, rx timeout 2 sec., ack/nack disabled, FIFO
enabled, serial trigger lock disabled;
DATA FORMAT : code identifier enabled, no field adjustment,
code length not transmitted, no header, terminator = CR,
character replacement disabled
RS232 ICL DEFAULT SETTINGS
9600 baud, parity even, 8 data bits, 1 stop bit, handshaking
RTS always on, delay disabled, rx timeout 9.9 sec., ack/nack
disabled, FIFO enabled, serial trigger lock disabled;
DATA FORMAT : code identifier enabled, no field adjustment,
code length not transmitted, no header, terminator = CR,
character replacement disabled
WEDGE DEFAULT SETTINGS
USA keyboard, caps lock off, num lock unchanged, inter-
character and inter-code delays disabled, control character
emulation = ctrl+shift+key;

TECHNICAL FEATURES
GRYPHON

D100 - D200
Electrical Features
Power Supply 5 Vdc ±5%
Consumption:
Maximum
Operating
Sleep mode
330 mA
250 mA
250 µA
Sensor CCD solid state (3648 pixels)
Max. Scan Rate 270 scans/sec
Reading Field see reading diagrams
Max. Resolution 0.076 mm (3 mils)
PCS min. 15% (Datalogic Test Chart)
Reading Indicators LED, Good Read Spot, Beeper
Environmental Features
Working Temperature 0 °C to + 55 °C
Storage Temperature -20 °C to + 70 °C
Humidity 90% non condensing
Drop Resistance IEC 68-2-32 Test ED
Protection Class IP30
Mechanical Features
Weight (without cable) about 200 g. (7 oz.)
Cable Length 2 m (6.1 ft.)
The following Keyboard Nationality selection is only valid for
IBM AT compatible PCs:
Japanese
i'+k
i'+k
i'+k
UK
YOUR READER IS NOW READY TO READ
BARCODES.
To change the defaults see the GryphonSoftware
Configuration Manual, part number 90ACC1780.
I IL LETTORE È PRONTO A LEGGERE I CODICI.
Per cambiare i parametri di default, fare riferimento
al manuale "GryphonSoftware Configuration
Manual", n. d'ordine 90ACC1780.
F VOTRE LECTEUR EST DÉSORMAIS PRÊT A
L’EMPLOI POUR LA LECTURE DE CODES.
Pour changer les paramètres voir le manuel
"GryphonSoftware Configuration Manual" numéro
d'ordre 90ACC1780.
D DAS LESEGERÄT IST JETZT BEREIT CODES ZU
LESEN.
Um die Werkseinstellungsparameter zu ändern,
schlagen Sie im Handbuch " GryphonSoftware
Configuration Manual" nach, Bestellnummer
90ACC1780.

3 OPERATING TEST
UK Read the TEST codes below.
I Leggere i codici di test.
F Lire les codes tests.
D Lesen Sie die Test-Coden.
EAN-8
1234 5670
EAN-13
1 234567 000992
Code 39 (Normal)
17162
Code 128
test
Interleaved 2 of 5
0123456784
PDF417
DATALOGIC PDF417 Test Code
WEDGE
With the Wedge or PC Notebook cables, this accessory device
is intended to be connected to either a UL Listed Computer
which supplies power directly to the reader or a UL Listed
Direct Plug-in Power Unit marked "Class 2", rated 5 V,
minimum 330 mA.
DISCONNECTING THE CABLE

CONNECTIONS RS232
With the RS232 cable, this accessory device is intended to be
supplied by a UL Listed Direct Plug-in Power Unit marked
"Class 2", rated 5 V, minimum 330 mA.
PEN
With the Pen Emulation cable, this accessory device is
intended to be supplied by a UL Listed Power Unit marked
"Class 2", or an LPS power source which supplies power
directly to the reader.
WEDGE
WARRANTY
UK Datalogic warranties this product against defects in
workmanship and materials, for a period of 24
months from the date of shipment, provided that the
product is operated under normal and proper
conditions.
Datalogic has the faculty to repair or replace the
product, these provisions do not prolong the original
warranty term.
The warranty does not apply to any product that has
been subject to misuse, accidental damage,
unauthorized repair or tampering.
I
Datalogic garantisce questo prodotto contro difetti di
fabbricazione e di materiali per 24 mesi dalla data di
consegna, a condizione che il prodotto sia utilizzato
come previsto.
Datalogic si riserva la facoltà di riparare o sostituire
il prodotto. Quanto sopra non prolunga la garanzia
originale.
La garanzia non si applica a prodotti utilizzati in
modo non corretto, danneggiati accidentalmente,
sottoposti a riparazioni non autorizzate o
manomessi.
F
Datalogic garantit ce produit de tout défaut de
fabrication ou des matériels pendant 24 mois de la
date de livraison, à condition que le produit soit
utlisé correctement.
Datalogic a la faculté de réparer ou de remplacer ce
produit. Ces mesures ne prolongeront pas
l’échéance de la garantie.
La garantie ne s’applique pas aux produits qui ont
été utilisés de façon incorrecte, accidentellement
endommagés, soumis à des réparations non
authorisées ou gâchés.
D
Datalogic gibt für dieses Produkt eine Garantie von
2 Jahren auf Herstellungs- und Materialfehler ab
Versandsdatum, falls das Produkt unter normalen
und angemessenen Bedingungen verwendet wurde.
Datalogic behaltet sich vor, das Produkt entweder
zu reparieren oder zu ersetzen, was aber den
originalen Garantietermin nicht verlängert.
Die Garantie ist nicht gültig, falls das Produkt falsch
angewandt, zufällig beschädigt, unberechtigt
repariert oder verändert wird.

PATENTS
This product is licensed under one or more of the following
U.S. patents:
4,282,425; 4,570,057; 4,766,300; 4,894,523; 5,021,642;
5,038,024; 5,081,343; 5,095,197; 5,144,119; 5,144,121;
5,182,441; 5,187,355; 5,187,356; 5,218,191; 5,233,172;
5,258,606 and /or 5,288,985
This product is covered by one or more of the following patents
and patent applications:
US 5,917,176; US 5,992,740; US 6,010,073;
US pat. Appl. 99US-320.643; US pat. Appl. 99US-362.988;
US pat. Appl. 98US-126.606; EP pat. Appl. 00EP-830.127;
EP pat. Appl. 00EP-830.122; EP pat. Appl. 98EP-830.336;
EP pat. Appl. 98EP-830.611; EP pat. Appl. 97EP-200.317;
EP pat. Appl. 97EP-830.408; EP pat. Appl. 96EP-830.473;
EP pat. Appl. 96EP-830.660; EP pat. Appl. 96EP-830.439
FCC COMPLIANCE
This device complies with PART 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference which
may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
LED CLASS
CLASS1 LED PRODUCT APPARECCHIO LED CLASSE 1
LED KLASSE 1 APPAREIL A LED DE CLASSE 1
EN60825-1/LED11 1996
READING DIAGRAMS
GRYPHON

D100 (STANDARD)
0 5 10 15 20 25 30 35
-15
-10
-5
0
5
10
15
D100 (STD) - Reading Zones (10° skew angle)
(cm)
CODE 39
0.13 mm
(5 mils)
EAN13 M=1
0.33 mm
(13 mils)
CODE 39
0.50 mm
(20 mils)
CODE 39
0.076 mm
(3 mils)
0.13 mm
(5 mils)
GRYPHON

D200 (PDF)
0 5 10 15 20 25 30 35
-10
-5
0
5
10
D200 (PDF) - Reading Zones (10° skew angle)
(cm)
CODE39
0.076 mm
(3 mils)
CODE39
0.13 mm
(5 mils)
EAN13 M=1
0.33 mm
(13 mils)
CODE39
0.50 mm
(20 mils)
0.13 mm
(5 mils)
0246810 12 14 16
-8
-6
-4
-2
0
2
4
6
8
(cm)
D200 (PDF) - PDF417 codes, Reading Zones (10° skew angle)
PDF417 Aspect Ratio 3:1
0.25 mm
(10mils)
0.17 mm
(6.6mils) 0.38 mm (15mils)

USING GRYPHON

SERIES READERS
UK
Gryphonguns automatically scan barcodes at a distance.
Simply aim and pull the trigger. Code scanning is performed
along the center of the light bar emitted from the reading
window. This bar must cover the entire code.
Successful scanning is obtained by tilting the scanner with
respect to the barcode to avoid direct reflections which impair
the reading performance, see the figure above.
Successful reading is obtained by an audible tone plus a good-
read green spot.
I
Con le pistole Gryphonla lettura dei codici a barre avviene a
distanza: è sufficiente mirare sul codice e premere il grilletto.
La finestra anteriore proietta una banda luminosa che deve
essere centrata sul codice e attraversarlo interamente. Le
condizioni ottimali per la lettura si ottengono quando la pistola
viene usata con un'inclinazione rispetto al piano su cui si trova
il codice, così da evitare il rischio di riflessione diretta, che
potrebbe compromettere il risultato della lettura (vedi figura).
La buona lettura è segnalata da un beep sonoro e da uno spot
verde che illumina il codice.
F
Avec les pistolets Gryphon, la lecture des codes s'effectue
automatiquement et à distance. Il est suffisant de viser le
code. Le faisceau sortant de la fenêtre de lecture de l'appareil
lit le code. Ce faisceau doit être centré sur le code à barres à
lire et doit le traverser de part en part.
Pour des prestations optimales inclinez la douchette par
rapport au code à lire, afin d'éviter des réflexions directes qui
pourraient compromettre la performance de lecture (voir la
figure ci-dessus).
La lecture correcte est signalée par un beep sonore ainsi que
par un spot vert qui illumine le code lu.
D
Die GryphonLesepistolen lesen Strichcodes automatisch und
berührungslos. Es genügt auf den Code zu zielen und zu
drücken. Der Code wird mittels eines Lichtbands gelesen, der
das Gerät durch das Lesefenster verläßt. Dieses Lichtband
muß den gesamten Code möglichst in der Mitte durchqueren.
Eine optimale Lesegarantie ist gewährleistet, wenn der
Benutzer die Pistole bzgl. der Oberfläche, auf der sich der
Code befindet, etwas neigt, um eine direkte Reflexion zu
vermeiden, wie im Bild oben gezeigt wird.
Das erfolgreiche Lesen wird durch einen "Beeper" und ein
rundes grünes Licht angezeigt.
DATALOGIC S.p.A.,
Via Candini, 2
40012 - Lippo di Calderara
Bologna - Italy
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
GRYPHON D100, CCD Hand Held Reader
GRYPHON D200, CCD Hand Held Reader
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista
siguiente:
89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi
and further amendments
et ses successifs amendements
und späteren Abänderungen
y succesivas enmiendas
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità
elettromagnetica ed alla sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic
compatibility and product safety.
Basée sur la législation des Etates membres relative à la compatibilité
électromagnétique et à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf
elektromagnetische Verträglichkeit und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la
compatibilidad electromagnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con la siguientes normas:
EN 55022, August 1994: L IMITS AND METHODS OF MEASUREMENTS OF
RADIO DISTURBANCE OF INFORMATION
TECHNOLOGY EQUIPMENT
(ITE)
EN 50024, September 1998: I NFORMATION T ECHNOLOGY E QUIPMENT .
I MMUNITY CHARACTERISTICS . L IMITS AND
METHODS OF MEASUREMENTS
Lippo di Calderara, 05/02/2002
Ruggero Cacioppo
Quality Assurance Supervisor