Datalogic Gryphon-HC Series User manual

Gryphon-HC Handheld Products Cleaning Procedure
Applicable to Gryphon I GD4XXX-HC, GM4XXX-HC, 
GBT4XXX-HC Healthcare Models



Corded Models
Exterior surfaces and scan windows exposed to spills, smudges or
debris accumulation require periodic cleaning to ensure best per-
formance during scanning operations.
Use a soft, lint-free cloth or lens tissue to clean the product.
Dampen it with an approved cleaning agent. Gently wipe all sur-
faces.
Use approved cleaning agents only (see Table 1 below).
Item Description Item Description
Sani-Cloth® HB, Sani-Cloth® Plus,
Super SaniCloth®
Quaternary Ammonium Chloride
solution Virex® 256
n-Alkyl Dimethyl Benzyl 
Ammonium Chloride; Didecyl
Dimethyl Ammonium Chloride
Hepacide Quat Il Virucidal disinfectant cleaner 409® Glass and Surface Cleaner Isopropanol (Isopropyl Alcohol),

2 propanol, dimetil carbinol
Alcohol Wipes 70% Isopropyl Alcohol Windex® Blue Isopropyl Alcohol
CaviWipes™ Isopropanol 10-20%; Ethylene Glycol
Monobutyl Ether 1-5% Clorox® Bleach Sodium Hypochlorite;

Sodium Hydroxide
100% Gentle dish soap and water
*When using Ammonia Chloride Solutions be sure to remove residue from the contacts after cleaning.
Do not use abrasive or aggressive cleansing agents or
abrasive pads to clean scan windows, contacts, or
plastics.
Do not spray or pour liquids directly onto the unit.
Table 1. Tested Cleaning Agents
CAUTION
INSTRUCTIONS
BSR idware GmbH
Jakob-Haringer-Str.3
A-5020 Salzburg
Web: www.bsr.at

Gryphon-HC Handheld Products Cleaning Procedure Page 2
Cordless Models
Exterior surfaces and scan windows exposed to spills, smudges or
debris accumulation require periodic cleaning to ensure best perfor-
mance during scanning operations. Contacts on the scanner and the
base should also be cleaned as needed to ensure a good connection.
See below for specific information on how to clean the metal con-
tacts.
Use a soft, lint-free cloth or lens tissue to clean the product. Dampen
it with an approved cleaning agent. Gently wipe all surfaces. A cotton
swab may be used only on hard-to-reach handheld contacts.
Use approved cleaning agents only (see Table 1).
Handheld Contacts
1. Moisten a soft dry cloth with an approved cleaning agent (see Table 1).
2. Rub the cloth back and forth across the contacts. Use care not to leave any cloth
residue.
3. Use the cloth to remove any dirt near the contacts area.
4. Repeat steps 1-3 using a clean dry cloth.
5. Finish by using another clean dry cloth to remove any residue of the cleaning
agent from the contacts.
Cradle Contacts
CAUTION
Do not use abrasive or aggressive cleansing agents or
abrasive pads to clean scan windows, contacts, or
plastics.
Do not spray or pour liquids directly onto the unit.
850006914 (Rev A) October 2013
1. Remove the power cable before cleaning the contacts.
2. Moisten a soft dry cloth with an approved cleaning agent (see Table 1).
3. Rub the cloth from one side of the contacts to the other, moving it slowly back
and forth. Use care not to leave any cloth residue.
4. Use the cloth to remove any dirt near the contacts area.
5. Repeat steps 2, 3 and 4 using a clean dry cloth.
6. Finish by using another clean dry cloth to remove any residue of the cleaning
agent from the contacts.
©2013 Datalogic, Inc. • All rights reserved. • Datalogic and the Data-
logic logo are registered trademarks of Datalogic S.p.A. in many coun-
tries, including the U.S.A. and the E.U.
www.datalogic.com