Datalogic Gryphon M 00 Series User manual

Quick Reference Guide
www.scanning.datalogic.com
Gryphon™ Mx00
Datalogic Scanning, Inc.
959 Terry Street
Eugene, OR 97402
Telephone: [phone]
Fax: [phone]
Australia
Datalogic Scanning Pty Ltd
North Ryde, Australia
Telephone: [61] (2) 9870 3200
Fax: [61] (2) 9878 8688
France and Benelux
Datalogic Scanning Sarl
LES ULIS Cedex, France
Telephone: [33].01.64.86.71.00
Fax: [33].01.64 46.72.44
Germany
Datalogic Scanning GmbH
Darmstadt, Germany
Telephone: [phone]
Fax: [phone]
Italy
Datalogic Scanning SpA
Vimercate (MI), Italy
Telephone: [39] (0) 39/62903.1
Fax: [39] (0) 39/6859496
Japan
Datalogic Scanning KK
Shinagawa, Tokyo, Japan
Telephone: [phone]
Fax: [phone]
Latin America
Datalogic Scanning, Inc
Miami, Florida, USA
Telephone: [phone]
Fax: [phone]
Spain and Portugal
Datalogic Scanning Sarl
Sucursal en España
Madrid, Spain
Telephone: [phone]
Fax: [phone]
United Kingdom
Datalogic Scanning LTD
Watford, England
Telephone: [phone]
Fax: [phone]
©2007 Datalogic Scanning, Inc. 820000745eng (Rev. G) 09/07

Datalogic Scanning, Inc.
959 Terry Street
Eugene, Oregon 97402
Telephone: [phone]
Fax: [phone]
An Unpublished Work - All rights reserved. No part of the contents of this
documentation or the procedures described therein may be reproduced or
transmitted in any form or by any means without prior written permission of
Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic
Scanning”). Owners of Datalogic products are hereby granted a non-exclusive,
revocable license to reproduce and transmit this documentation for the
purchaser's own internal business purposes. Purchaser shall not remove or
alter any proprietary notices, including copyright notices, contained in this
documentation and shall ensure that all notices appear on any reproductions of
the documentation.
Should future revisions of this manual be published, you can acquire printed
versions by contacting your Datalogic representative. Electronic versions may
either be downloadable from the Datalogic website
(www.scanning.datalogic.com) or provided on appropriate media. If you visit our
website and would like to make comments or suggestions about this or other
Datalogic publications, please let us know via the "Contact Datalogic" page.
DISCLAIMER
Datalogic has taken reasonable measures to provide information in this manual
that is complete and accurate, however, Datalogic reserves the right to change
any specification at any time without prior notice. Datalogic is a registered
trademark of Datalogic S.p.A. in many countries and the Datalogic logo is a
trademark of Datalogic S.p.A. all licensed to Datalogic Scanning, Inc. All other
trademarks and trade names referred to herein are property of their respective
owners.

iii
CONTENTS
Updates and Language Availability.....................................................................iv
Using Gryphon™ M Series Readers................................................................... 1
Charging the Batteries ........................................................................................ 2
Gryphon™ M Configuration ................................................................................ 3
Using Multiple Readers with Same Cradle.......................................................... 5
Gryphon™ M Default Configuration .................................................................... 5
Technical Features.............................................................................................. 7
Warranty.............................................................................................................. 8
Services and Support.......................................................................................... 8
Patents ................................................................................................................ 8
Compliance ......................................................................................................... 8
Reading Diagrams ............................................................................................ 10
Numeric Table................................................................................................... 11

iv
UPDATES AND LANGUAGE AVAILABILITY
UK/US
The latest drivers and documentation updates for this product are available on
Internet.
Log on to: www.scanning.datalogic.com
I
Su Internet sono disponibili le versioni aggiornate di driver e documentazione di
questo prodotto. Questo manuale è disponibile anche nella versione italiana.
Collegarsi a: www.scanning.datalogic.com
F
Les versions mises à jour de drivers et documentation de ce produit sont
disponibles sur Internet. Ce manuel est aussi disponible en version française.
Cliquez sur: www.scanning.datalogic.com
D
Im Internet finden Sie die aktuellsten Versionen der Treiber und Dokumentation
für dieses Produkt. Die deutschsprachige Version dieses Handbuches ist auch
verfügbar.
Adresse : www.scanning.datalogic.com
E
En Internet están disponibles las versiones actualizadas de los drivers y
documentación de este producto. También está disponible la versión en
español de este manual.
Dirección Internet: www.scanning.datalogic.com

GRYPHON™ MX00
1
USING GRYPHON™ M SERIES READERS
The Gryphon™ M series reader, paired with an OM-Gryphon™ cradle, builds a
Cordless Reading System for the collection, decoding and transmission of
barcoded data.
Gryphon™ M readers automatically scan barcodes at a distance. Simply aim
and pull the trigger. Code scanning is performed along the center of the light bar
emitted from the reading window. This bar must cover the entire code.
READING ANGLE
Successful scanning is obtained by tilting the reader with respect to the barcode
to avoid direct reflections, which impair the reading performance, see the figure
below.
Successful reading is obtained by an audible tone plus a good-read green spot.
OK Not Advised
To start using your Gryphon™ M reading system you must:
1. Connect an OM-Gryphon™ cradle to the Host. For installation and
connection information see the OM-Gryphon™ Quick Reference Guide.
2. Charge the Gryphon™ M battery using an OM-Gryphon™ / C-Gryphon™
charger as described in this Quick Reference Guide. A full charge takes
3.5 hours with NiMh battery models.
3. Configure the reader as described in this Quick Reference Guide.
4. Configure the OM-Gryphon™ cradle. See OM-Gryphon™ Configuration in
the “OM-Gryphon™ Quick Reference Guide”.
Good read spot
Good read LED

DATALOGIC
2
CHARGING THE BATTERIES
By placing the reader onto the OM-Gryphon™ cradle or C-Gryphon™ battery
charger it is possible to charge the Gryphon™ M batteries. Make sure the
charging LED goes on.
The LEDs positioned on the cradle signal the charge status, as described in the
following table:
LED STATUS
Power on /
Data
Yellow On = OM-Gryphon™ is powered.
Yellow Blinking = OM-Gryphon™ receives data and
commands from the Host or the reader.
Charging Red On = the battery charge is in progress.
Red Blinking = the battery reconditioning is in progress.
Charge
completed Green On = the battery is completely charged.
Charging +
Charge
completed
Red and Green Blinking together = the reader is not
correctly placed onto the reader.
D
I
S
C
H
A
R
G
E
After many recharging cycles NiMh and NiCd batteries may tend to lose their
operating autonomy. This condition can be overcome by positioning the
Gryphon™ M onto the OM-Gryphon™ / C- Gryphon™ charger and pressing the
“battery reconditioning” button.
Power on / Data
(yellow LED)
Reconditioning battery
button
Charging
(red LED)
Charge completed
(green LED)

GRYPHON™ MX00
3
When the above procedure is no longer effective, the batteries must be
changed. To change the batteries of your reader, unscrew the battery cover
screw, replace the old batteries with new ones, then insert the cover in the
handle and screw it back into place. (See the following figures).
WARNING
Do not incinerate, disassemble, short terminals or
expose to high temperature. Risk of fire, explosion. Use
specified charger only. Risk of explosion if the battery
is replaced by an incorrect type. Dispose of the
batteries as required by the relevant laws in force.
GRYPHON™ M CONFIGURATION
When the OM-Gryphon™ cradle is connected and powered, configure the
Gryphon™ M by reading the following codes in the given sequence and follow the
instructions.
Note: for the numeric code selection of step 3, use the table at the end of this
Quick Reference Guide.
Restore Gryphon™ M default
1. Ì$+$*oÎ
Enter configuration
2. Ì$+;Î
Set Radio Address
3.
ÌRF8Î
+
four digits for the Gryphon™ M Address
(from 0000 to 1999).
All readers used in the same area must have different addresses.
+

DATALOGIC
4
Exit and Save configuration
4. Ì$-?Î
5. Read the Bind code to pair the Gryphon™ M to the OM-Gryphon™
cradle.
The reader is dedicated to the cradle. Any previously bound reader will
be excluded.
To connect several readers to the same cradle see the following section
"Using Multiple Readers with Same Cradle".
Bind
Ì$+RN0$-IÎ
The green LED on the Gryphon™ M will blink: the reader is ready to be
positioned onto the cradle.
6. Firmly position the reader onto the cradle within 10 seconds, a beep will
be emitted, signaling that the OM-Gryphon™ cradle has been paired to
the Gryphon™ M, and the green LED on the reader will go off.
YOUR READER IS NOW CONFIGURED TO READ CODES USING THE
DEFAULT VALUES.
7. Configure the OM-Gryphon™ cradle; refer to the “OM-Gryphon™ Quick
Reference Guide”.
Green LED

GRYPHON™ MX00
5
USING MULTIPLE READERS WITH SAME
CRADLE
If you want to use several readers associated with the same cradle, you must
first Bind the cradle with one of the readers (see previously described
configuration procedure).
Successive readers can be associated with the same cradle by following the
configuration procedure substituting the Bind command with Join.
5. Join
Ì$+RN1$-NÎ
The green LED on the Gryphon™ M will blink: the reader is ready to be
positioned onto the cradle. Complete step 6.
CAUTION
If the cradle is not Bound to a reader, its address assumes
a random value, which can cause conflicts and malfunctions
to other cradles within its range.
GRYPHON™ M DEFAULT CONFIGURATION
DATA FORMAT
code identifier disabled (enabled for POS terminals), field adjustment
disabled, code length tx not transmitted, character replacement disabled
POWER SAVE
scan rate 270 scans/s
READING PARAMETERS
operating mode hand-held, hardware trigger, trigger active level, no timeout,
Flash On = 1 sec, Flash Off = 0.6 sec, one read per cycle, safety time 0.5
sec, beeper intensity high, tone 2, beeper type monotone, beeper length
short, good read spot duration medium
DECODING PARAMETERS
ink spread enabled, overflow control enabled, interdigit control enabled,
Puzzle Solver™ disabled, decoding safety = one read

DATALOGIC
6
CODE SELECTION
Enabled codes
• Code PDF417 (only Gryphon™ M200)
• EAN 8/EAN 13 / UPC A/UPC E without ADD ON
check digit transmitted, no conversions
• Interleaved 2/5
check digit control and transmission, variable length code; 4-99
characters
• Standard Code 39
no check digit control, variable length code; 1-99 characters
• Code 128
variable length code; 1-99 characters
Disabled codes for M100 only:
EAN 128, ISBT128, Code 93, Codabar, pharmaceutical codes, MSI,
Plessey, Telepen, Delta IBM, Code 11, Code 16K, Code 49,
RSS Codes
Disabled codes for M200 only:
EAN 128, ISBT128, Code 93, Codabar, pharmaceutical codes,
RSS Codes
ADVANCED FORMATTING PARAMETERS
concatenation disabled, no advanced formats defined
RADIO PARAMETERS
radio protocol timeout = 2 seconds, power-off timeout = 4 hours, single store
disabled, beeper control for radio response = normal.