Datum Storage Ez2 Drawer User manual

Ez2 Assembly Instructions
Page 1
If you need assembly assistance, please contact Customer Service at:
1-866-217-0330 (Monday thru Friday 8:00 A.M. - 5:00 P.M. E.S.T.)
INST0081REV1TJE5/25/04

Ez2 Assembly Instructions
Page 2
Included Hardware:
(Full Scale)
1/4-20 x 1/2" Phillips
Pan Head Screw
#8 x 1/2" Phillips
Pan Head Screw
1/4-20 x 3/4"
Countersink Allen
Flat Head Screw
1/4-20 x 5/8" Phillips
Pan Head Screw
1/4-20 Nylock Nut
#10-24 x 1/2"
Type 'F' Phillips
Pan Head Screw
#10 x 3/8" Phillips
Pan Head Screw
3/16 x 3/8" Allen
Head Cap Shoulder
Screw
1/4 Diameter
Spacer
1/4-20 Tinnerman
Nut
1/4-20 Flanged
Hex Nut
(Tube of Thread Adhesive
Not Shown)
3/32" Allen Wrench
(Not Shown Full Size)
5/32" Allen Wrench
(Not Shown Full Size)

Ez2 Assembly Instructions
Page 3
Parts
Base Assembly Top Cover of
Rotating Cabinet
Left Upright
(Qty 2) Right Upright
w/Lock
Side Panel
(Qty 2)
Right Upright
w/Lock Plug
Front/Rear
Front/Rear
Side
Side

Ez2 Assembly Instructions
Page 4
Parts
Top Cover
Cabinet Divider
Divider
Shelf
End Panel
(Optional)
Edge Guard
(Qty 4)

Figure A
B
Detail B
Ez2 Assembly Instructions
Page 5
Step 1:Using provided 5/32" allen
wrench, attach a left upright to the base with
two 1/4-20 x 3/4 Flat Countersink Allen Cap
Screws (see Figure A and Detail B).
Left Upright
Base
Front of Unit
Side of Unit
Left Upright Base
1/4-20 x 3/4" Screw

Figure C
D
Detail D
Figure E
Ez2 Assembly Instructions
Page 6
Step 2:Attach right upright with lock to
base with two 1/4-20 x 3/4 Flat Countersink
Allen Cap Screws (see Figure C and Detail D).
Step 3:Repeat Steps 1 & 2 for the rear
of the unit. Use right upright with lock plug
for rear of unit. The unit should now look
like Figure E.
Right Upright
w/Lock
Left Upright
Base
Front of Unit
1/4-20 x 3/4"
Screw
Base
Right Upright
w/Lock Plug
Left
Upright
Right Upright
w/Lock

Figure F
G
Detail G
J
Figure H Detail J
Detail K
Ez2 Assembly Instructions
Page 7
Step 4:Remove two shipping bolts from
top of base with a Phillips Head Screwdriver
(see Figure F and Detail G).
Step 5:Rotate spinning base 1/4 turn and
position lock bar as shown in Figure H and
Detail J. Insert hook end of lock bar into
rectangular slot (Detail J). Rotate lock bar so
it is in a vertical position (Detail K). Maneuver
lock bar until short end of hook protrudes
through return hole in base (Detail K).
CAUTION:
After removing shipping bolts, be careful not
to tilt unit as bearings may become dislodged.
Shipping
Bolts
Shipping Bolt
Base
Left Upright
Base
Return Hole
Rectangular
Slot
Lock Bar
Upright
Lock Bar
Return
Hole
Rectangular Slot

Figure L
Locked
Figure M
Unlocked
Ez2 Assembly Instructions
Page 8
Step 6:Apply a dab of lock adhesive in
cam hole. Push one 3/8" shoulder bolt
through lock bar and spacer tube, attach to
lock cam. Tighten with 3/32" allen wrench
supplied.
Step 7:Please verify correct positioning of lock
components when locked and unlocked (Figure M).
3/16" x 3/8"
Shoulder Bolt
Spacer
Apply dab of lock
adhesive in hole
Lock Bar Upright

Figure N
Detail P
Figure R
Ez2 Assembly Instructions
Page 9
Step 8:Attach first side panel with four #10 x
3/8" Phillips Pan Head Screws. The side panel will
fit onto the spinning base as shown in Figure N
and Detail P. ATTENTION: Support side panel so
it does not tip over and damage unit.
Step 9:Repeat Step 9 for second side
panel installation (Figure R).
Side Panel
Base Spinning Base
#10 x 3/8" Screw
Side Panel
Base
Spinning Base
Detail P

TFigure S
Detail T
Figure U
Ez2 Assembly Instructions
Page 10
Step 10:DO NOT TIGHTEN SCREWS
DURING THIS STEP!!! (Leave an 1/8" gap
between head of screw and surface of
metal)Fasten four #10-24 x 1/2" Type 'F'
Phillips Pan Head Screws to each side
panel as shown in Figure S and Detail T.
Step 11:Position top of rotating cabinet
as shown in Figure U with slots aligned with
the screws that were just installed. Now
tighten the screws.
#10-24 x 1/2" Screw
Side Panel
#10-24 x 1/2"
Screw
Top of Rotating
Cabinet
Side Panel

Figure V
Figure W
X
Detail X
Ez2 Assembly Instructions
Page 11
Step 12:Position top cover as shown in
Figure V. Make sure that shaft on top cover
goes into hub on top of rotating section.
Fasten top cover to uprights with a total of
eight #10 x 3/8" Phillips Pan Head Screws.
Step 13:Position and attach cabinet divider
using four 1/4-20 x 1/2" Phillips Pan Head Screws
and 1/4-20 Nylock Nuts (Figure W and Detail X).
Top Cover
#10 x 3/8" Screw
Cabinet
Divider
1/4-20 x 1/2" Screw
Cabinet Divider
1/4-20 Nut

Z
Figure Y
Detail Z
Ez2 Assembly Instructions
Page 12
Step 14:Fasten four #10-24 x 1/2" Type 'F'
Phillips Pan Head Screws at locations indicated
in Figure Y for each shelf that will be installed.
NOTE:
For standard filing applications, a small indicator
hole can be found next to each standard shelf hole
(see Detail Z). This will allow for equal shelf
openings and in most cases, it will leave enough
space for a posting shelf. Leave about an 1/8" gap
between head of screw and surface of side panel
when fastening screws in next step.
#10-24 x 1/2" Screw
Indicator Hole

Figure AA
Figure AB
Figure AC
Ez2 Assembly Instructions
Page 13
Step 15:To install shelf, position shelf so it hooks
on to front two mounting screws (Figures AA & AB),
then push shelf in and tip it down so rear of shelf hooks
on to rear two screws (Figure AC). Tighten screws.
Step 16:Repeat Step 15 to install
remainder of shelves.
Shelf
#10-24 x 1/2"
Screw
Side
Panel
Side
Panel
Shelf
#10-24 x 1/2"
Screw
Side Panel Shelf
#10-24 x 1/2"
Screw

AF
AE
Ez2 Assembly Instructions
Page 14
Step 17:Units will attach to each other by using six 1/4-20
x 5/8 Phillips Pan Head Screws and Nuts (see Figure AD and
Detail AE). Units attaching to an end panel will use six 1/4-20 x
5/8 Phillips Pan Head Screws (see Figure AD and Detail AF).
Figure AD
Detail AE
*Inside of cabinet not shown for clarity.
End Panel
1/4-20 x 5/8
Screw
1/4-20 Nut
1/4-20 x 5/8 Screw
End Panel Should Have
Tinnerman Nuts Attached
Detail AF
Note: Unit shown
consists of one
starter and one
add-on unit.

Figure AG
Figure AH
Ez2 Assembly Instructions
Page 15
Step 18:To install dividers, insert front tab first
(Figure AG). Then insert rear two tabs (Figures AH).
Two dividers per shelf.
Divider
Shelf
Shelf
Divider

Figure AL
Top View of Upright
AK
Detail AK
Figure AJ
Ez2 Assembly Instructions
Page 16
Step 19:Attach edge guards to the four
uprights. Edge guards attach by simply pressing
them on short flange of each upright (Detail AK).
Edge Guard Upright
Top Cover
Edge Guard
Upright

AN
Ez2 Assembly Instructions
Page 17
Step 20:To level the unit, use a 3/16" Nut
Driver to adjust the four leveling glides from the
access holes in top of base (see Detail AN).
Detail AN
Access Hole for Leveling
Figure AM