STILFORD PROFESSIONAL 2 ERGONOMIC EXTRA HEAVY DUTY CHAIR... User manual

PROFESSIONAL 2 ERGONOMIC EXTRA
HEAVY DUTY CHAIR
1/10
JBPROFM2BK
ASSEMBLY INSTRUCTIONS
Weight capacity: 160kgs
This design and instruction booklet is subject to copyright.
www.officeworks.com.au
For spare parts or hardware call [phone] or email [email protected]
1CTN

15
2/10
Officeworks Ltd. | 236-262 East Boundary Road | Bentleigh East VIC 3165 | AUSTRALIA
• Please check you have all hardware before assembly.
• If you are missing any hardware, please contact Kyvas on [phone] or email
[email protected]
• Please ensure you have the name of the item, required hardware part and quantity.
• Please retain your receipt as proof of purchase to validate your warranty.
.
NOTE
• Do not tighten screws before all screws are in the right place.
• Do not use this product unless all bolts, screws and knobs are firmly secured.
• Check that all bolts, screws and knobs are securely tightened at least every 4 months.
CAUTION
• If parts are missing, broken, damaged or worn stop using the product until all repairs
are made using manufacturer authorised parts.
• Failure to follow these warnings could result in serious injury
WARNING
• CHILDREN MUST BE SUPERVISED.
DANGER
[phone]
Tools Required
CAUTION: Do not use tools other than those required, as this can damage your new item.
Please ensure drill is set to torque 5Nm.
Assembly Video
•To view an assembly video,go to https://www.officeworks.com.au
•Search the product by item code or name:
•Click on the icon to watch the video.

G
(5/16" x 3/4") H(1/4" x 1-1/4")
x 1
x 3 x 6
I
3/10
x1
x1 x5
x1 x2
x1
FRONT

D
E
E
F
4/10
Note: Turn over the Star Base (E) and insert Gas Lift (D) into the centre hole of Star Base (E).
Note: Push the castors (F) firmly into hole at the end of each leg.

H
6 Pcs
1/4" x 1-1/4" Bolt
used to complete
this step.
C-R C-L
B
D
B
Note: Place assembled seat on the Gas Lift (D). Push down firmly until connection is secure.
5/10
Note: Do not tighten Screws fully until you have completed assembly.
H
I
Torque 5 Nm
C-L
C-R
FRONT

Note: Align Back Cushion (A) with Seat Cushion (B) by GENTLY inserting J-bar into the rear
hole of the Seat Plate (B) as shown and TIGHTEN by using 3 x screws (G). When using
a drill set the torque to 5Nm to avoid over-tightening. Before using your chair, ensure that
all the screws are tightened fully for safety.
Note: Extend the J-bar by holding the backrest with one hand and pull the bottom of J-bar
with other hand.
G
3 Pcs
5/16" x 3/4" Bolt
used to complete
this step.
6/10
A
B
A
J-bar
J-bar
A
G
I
6
Remark: For assembly the J-bar needs to be
extended as shown in the diagram.
Torque 5 Nm

Your Professional 2 Ergonomic Extra Heavy Duty Chair is now complete and ready for use.
IMPORTANT NOTE: Periodically check and re-tighten screws
7/10
Thank you for your purchase. Please retain your receipt to validate warranty.
If you would like to know more about our furniture products, please visit www.officeworks.com.au
• Spot clean fabric/mesh with upholstery shampoo or dry cleaning powder only
.
• Do not saturate fabric. Apply proprietary cleaning products strictly according
to instructions. Wipe dry immediately with an absorbent dry cloth.
•Treat spills on fabric material immediately with an absorbent cloth by blotting the spill.
• Do not use detergents, solvents or abrasive cleaners.
Care Instructions
• Keep away and protect from direct sunlight and heat.
•Avoid contact with skin, in particular during high temperatures and humidity.
• Clean, check and tighten all parts regularly.
• Vacuum regularly.
7

Chair Tilt
Gas-Lift Height
Seat Slide
8/10
PROFESSIONAL 2 ERGONOMIC EXTRA
HEAVY DUTY CHAIR
Functionality
- Adjust the back height up and down by pulling
up the back using the supporting bar with both
your hands.
- To set the backrest to lowest position pull backrest
up as far as it will go with both hands and then push
down until it stops.
- The backrest has 9 x levels of height adjustment that
can be heard by a clicking sound at each level as the
back rest is being pulled upwards. To set the backrest
at one of these levels pull the backrest from the supporting
bar gently with both hands and stop at the desired height.
- To set the backrest to its highest position gently pull
upward with both hands and stop as you hear the 9th click.
- Sitting in the chair pull lever up.
Move your upper body forward/backward
to a comfortable position.
- When comfortable lock the
position by pushing the lever down.
- Sitting in the chair pull lever up.
Move your body to a comfortable
position. Lock the position by
pushing the lever down.
- To adjust chair height, pull
lever upward while lifting body
weight slightly off the seat.
- Release lever at desired height.
- To lower chair height sit fully into
the chair and pull lever upward.
- Release lever at desired height.
Your feet should be resting flat on
the floor.
- Lift this lever to slide the
seat forwards or backwards.
- Release the lever to lock.
SEAT
SLIDE

Adjustable Tilt Tension Control
PROFESSIONAL 2 ERGONOMIC EXTRA
HEAVY DUTY CHAIR
Functionality
Pull lever up whilst moving the
arm up or down. Release lever
at desired height.
- Turn continuously to adjust how
quickly chair tilts back&forth.
Note: if adjusting while sitting in chair:
Turn knob left to tighten tension
Turn knob right to loosen tension
9/10
Function Video
•To view an function video,go to https://www.officeworks.com.au
•Search the product by item code or name:
•Click on the icon to watch the video.

10/10
Thank you for your purchase. Please retain your receipt to validate warranty.
If you would like to know more about our furniture products, please visit www.officeworks.com.au
Warranty 15 years
Product Warranty – valid for Australian customers only
Officeworks Ltd warrants that this product will be free from defects and work as
intended for 15 years from the date of purchase by the original customer.
If the product has any defects or does not work as intended during the Warranty Period,
Officeworks will, at its election and at its expense, repair or replace the product.
This warranty does not apply:
to cosmetic damage;
to damage caused by consumables used in connection with the product (such as
cleaning products);
where the product has not been used in accordance with all provided instructions;
to damage arising from fair wear and tear;
where the product has not been subject to reasonable use;
where the product has been intentionally or negligently damaged; and/or
if the customer has attempted to repair the product.
To make a claim under this warranty, please return your product with your receipt or
proof of purchase to your nearest Officeworks store or contact 1300 633 423.
This warranty is provided in addition to any rights you may be entitled to under the
Competitions &Consumer Act 2010.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
●
●
●
●
●
●
●