DAX BATHTUB FILLERS Series User manual

DAX-8180
BATHTUB FILLERS SERIES

FEATURES
DAX-8180
• Floor mount
• Brass body
• Chrome finish
• Anti-scalding protection
• Ceramic cartridge
• Hand shower included
• Mounting parts and water lines included
7-7/8”
36-1/8”
2-13/16”
1-1/8”~2”
1”
G1/2G1/2

ww w. daxib.c om
MODEL DAX-8180
ADA NO
ANSI APPROVED
UPC APPROVED
NO
NO
ASME APPROVED NO
WATERSENSE CERTIFIED NO
NSF APPROVED NO
FAUCET TYPE Waterfall
ANTI-SCALDING PROTECTION
NUMBER OF HANDLES
YES
1
INSTALLATION TYPE Floor Mounted
FINISH
SPOUT REACH
Chrome
7-7/8”
SPOUT HEIGHT
CARTRIDGE TYPE
36-1/8”
Ceramic
BATHTUB FILLER DAX-8180
TECHNICAL SPECIFICATION DAX-8180

ww w. daxib.c om
INSTALLATION GUIDE DAX-8180
01 02 03
04
07
05
08
06
09
Spirit level Teflon tape Pencil
S6 Allen key
(Provided)
S2.5 Allen key
(Provided)
Drill Goggles Spanner
Protection sheath
Inlet base
Hole
Hexnut
Spring shim
Flat shim
Expansion bolt
Spirit level
Longitudinal level detection
Horizontal level detection
Cold water inlet
Plug
Flange
Locking screw
Allen key
Hot water inlet
Cold water inlet
Flow water
Flow water
Hot water inlet
Faucet body
Inner pipe
Protection sheath
Escutcheon
Prepare and check the following tools.
Insert expansion bolts into holes on the floor
(Note:cold water inlet which printed with
“COLD” mark on inlet base faces to the bath-
tub),adjust the top surface of inlet base to level
position with spirit level and tighten with
hexnut.
Unscrew locking screw,remove flange and plug.
Put on protection sheath for paving floor tiles
(Note:the height of tiles should be at the same
level or a bit higher than the top surface of
protection sheath).
Take off protection sheath from inner pipe of
faucet body,put on escutcheon carefully to
avoid scratch to the surface of faucet body. Fix
flange(the side with counter bore back against
faucet body) with locking screw to faucet body
firmly.
Connect inlet base with cold and hot water
inlet pipe,cold water inlet faces to bathtub,
hot water inlet back against bathtub(means
front cold and back hot),wrap connectors
with teflon tape.Note to flow water to
get rid of dirt in pipes.Remove protection
sheath,insert plug into outlet of inlet base and
fix with flange.
Flow water for pressure test, ensure each
connection has no leakage occurs.
Take 4 mounting holes on inlet base (No-
te:ensure cold water inlet which printed with
“COLD” mark faces to bathtub)as benchmark
to draw line and drill 4 Ø12 holes on the floor. Install 4 expansion bolts to inlet base and
slightly tighten with hexnut.

ww w. daxib.c om
INSTALLATION GUIDE DAX-8180
1110 12
13
Handshower
Hose
Cold
Hot
Take off protection sheath,insert inner pipe verti-
cally into outlet of inlet base,connect flange and
inlet base with locking screw,tighten with allen
key.Close escutcheon to the floor. Connect handshower and faucet body with hose.
Pull diverter change water to handshower.
After installation,run water to check if the installa-
tion is qualified.The default state is when handle
open, water runs from bathtub.

PART LIST
[email protected]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
17
16
18
19
HandshowerFH 516
FH DB-14
FH 8180-13
FH 8129-10B
FH NZ14A-NP
FH KEROX-35
MF 5630
MF 0615
FH 8861B
FH D87-01
FH T-02A
FH 8180-12
FH D38A-02
FH TR06
FH TJ-30504
FH DB-13
FH TL-10816
FH TY-10850
MF 1424
PVC exible hose
Diverter
Ø1-3/8” cartridge
Stop screw
Locknut
Cartridge decorative ring
Handle
M5X4 Internal Hex at end locking screw
Ø3x1.5“O” ring
Decorative cap
Ø 3/8 x 1/16 “O” ring
Ø2x1/8“O” ring
Decorative cover
M8X16 Internal hex socket head cap screw
Expansion screw
Flange
Base
Check valve