DAXOM Naviels UKDAX-10EDT User manual

Dear DAXOM User
In order to perform device’s function properly and for your safety follow the
instructions mentioned in the user manual of the device during the mounting
and the usage of the device.
In case of an unauthorized mounting and maintenance, the device will be void
from warranty cover. In addition to that, our company will not be responsible
from failure or an accident that may occur in the device.
Please keep this user manual in good conditions for future reference.

1. Device installation must be made by authorized personnel according to
instructions that aredetermined inside this manual.
2. Start-up of device must be made by Authorized Service. Do not try to
operate the device by yourself.
3. Connection of water and heating installation of the device must be made
as safety.
4. Device can operate with the voltage determined inside this manual
according to its model. Suitable system voltage must be provided.
5. When it is supplied electric distribution from any electric resource (like
generator) except city electrical distribution network, must be sure that
necessary conditions are provided for safety operation of the device.
6. Energy must be provided to device with suitable cable diameter
determined inside this manual. Residual Current Device and grounding
must definitely place.
7. Installation of the device must not be made to humidity places and
places that can be wet from external factors.
8. Do not keep inflammable, explosive or easy flammable materials and
objects near the device.
9. This “INSTALLATION AND USER MANNUAL” is supplemental part of
the product. Please keep it for apply when it is necessary. Contact with
authorized service agency for the new copy in case of lost or damage.
10. This device must only be used as suitable as for its purpose.
Producer reject all kinds of liabilities that places or not places in the
agreement for damage property or injury indented to person and
animals which cause because of consumer wrong using, installation ,
setting and maintenance.
11. After you unpack the device, be sure that content is in good
position and complete otherwise contact with the sales agency that you
have purchased the device.
12. Safety valve outlet must be connected to suitable discharge and
ventilation system. Company rejects liability in case of any damage that
occurs because of any intervention to safety valve.
13. Remove all packing wastes carefully without giving damage to
human and environment health.
1. SAFETY WARNINGS

14. In case of water leakage happens, water feed must be close and
authorized service agency must be immediately informed.
15. Hydraulic system operation pressure must be between 1 and 2
bars therefore it must not exceed 3 bars. In case of need, pressure can
be reset as shown under the paragraph “FILLING THE SYSTEM”.
16. If the device will not used for a long time, perform following points
are suggested.
 Bring switch of the device OFF position.
 Close taps both heating and hot water network.
 Discharge heating and hot water network cycle for preventing
freezing.
17. Device cannot be used by children or disabled people without
helper.
18. In case of having smoked or burning smell originating from device,
make switch of the “OFF” position and contact with authorized service
agency.
19. Do not touch the device with wet hand or when outside of device is
wet.
20. Do not use substances such as detergent and thinner for the
cleaning of the device. Clean outside of the device with damp –dry
fabric.
21. Superheated water can be flow when the hot water is firstly
opened.
22. The lifetime of the device which is determined by Ministry of
Custom and trade is 10 years.
1. Adjust ambient temperature according to your need. Increasing 1 degree of
ambient temperature increases your energy consumption about %6.
2. Having homogeneous heating at parts according to intended use that is
placed at the heating place, increases saving.
2. SUGGESTIONS FOR ECONOMICALLY USED

3. Adjustable needed temperature value for every part by using thermostatic
valve for radiators increases the saving but using of room thermostat and
thermostatic valve at the same time can create problem.
4. While using of thermostatic valve and room thermostat,for sensing the
temperature correctly, make suitable position of objects such as curtain and
goods that influence ambient airstream.
5. Room thermos tad must be far away from goods and devices which
influences sense of ambient real temperature and must be place to suitable
height.
6. Ventilation of heated environment very long time increase the energy lost.
Short time ventilation must be made. If it is needed to make long time
ventilation, closing valve of ambient radiator or turn the device down provide
energy saving.
7. At night time or when you are not at home while turning device down
provides keeping temperature at definite level also can saving.
8. Adjustment of device operation temperature setting according to exterior
temperature provides saving.
9. Adjustment of tap water temperaturesetting according to your need as not
needed make lukewarm with cold water provides saving.
10. Use water as consciously. Consciously using water increase saving.

3. CONFIGURATION OF THE DEVICE

Technical
Specifications
Power (kW) Dimensions
L*W*H (mm)
Weight (Kg) Expansion
Tank (l)
Δt=25 oC Hot Water
Amount (l/min)
Model
3~400 V.50 Hz
Electrical Heating and Hot Water
UKDAX-10EDT
10 700*400*250 26 7 5,8
UKDAX
-
12EDT
12
700*400*250
26
7
6,9
UKDAX
-
16EDT
16
700*400*250
26
7
9,2
UKDAX-18EDT
18 700*400*250 26 7 10,4
UKDAX-20EDT
20 700*400*250 26 7 11,5
UKDAX-24EDT
24 700*400*250 26 7 13,8
UKDAX-30EDT
30 700*450*320 34 10 17,2
UKDAX-36EDT
36 700*450*320 34 12 17,2
UKDAX-40EDT
40 700*450*320 34 12 17,2
UKDAX-48EDT
48 700*450*320 34 12 17,2
1~220 V.50 Hz
Electrical Heating and Hot Water
UKDAX-10EDM
10 700*400*2
50
26 7 5,8
UKDAX-12EDM
12 700*400*2
50
26 7 6,9
UKDAX-16EDM
16 700*400*2
50
26 7 9,2
UKDAX-18EDM
18 700*400*2
50
26 7 10,4
3~400 V.50 Hz
Only Electrical
Heating
UKDAX-10ETT
10 700*400*2
50
23,8 7 -
UKDAX-12ETT
12 700*400*2
50
23,8 7 -
UKDAX-16ETT
16 700*400*2
50
23,8 7 -
UKDAX-18ETT
18 700*400*2
50
23,8 7 -
UKDAX-20ETT
20 700*400*2
50
23,8 7 -
UKDAX-24ETT
24 700*400*2
50
23,8 7 -
UKDAX-30ETT
30 700*450*3
20
31,8 7 -
UKDAX-36ETT
36 700*450*3
20
31,8 12 -
UKDAX-40ETT
40 700*450*3
20
31,8 12 -
UKDAX-48ETT
48 700*450*3
20
31,8 12 -
1~220 V.50 Hz
Only Electrical Heating
UKDAX-10ETM
10 700*400*2
50
23,8
7 -
UKDAX-12ETM
12 700*400*2
50
23,8
7 -
UKDAX-16ETM
16 700*400*2
50
23,8
7 -
UKDAX-18ETM
18 700*400*2
50
23,8
7 -
3~400 V.50 Hz
Only Electrical Heating Without Pump and
Expansion Tank
UKDAX-72ETP
72 800*450*320 37,8 -
Technical Specification
s
Radiator
Bath Water
Min.Operation
Pressure
bar 1 0,5
Max.Operation
Pressure
bar 3 10
Min.Setting
Temperature
oC 35 35
Max.Setting
Temperature
oC 80 55
Connections “ ¾ ½
4.
TECHNICAL SPECIFICATIONS

Boiler installation must be done by authorized personnel.
5. INSTALLATION OF BOILER

Obey minimum distance that is anticipated for installation in order to reach the
device for making regular maintenance.
5. 1 INSTALLATION CONDITIONS AND SAFETY WARNINGS

For the right position of the device;
Do not place on the cooker or similar cooking devices.
Do not leave combustion products inside device installed room.
Heating sensitive walls (for example wooden walls) must be protected with
steady insulation.
Before the installation, wash the all system pipes carefully for removing any
residual things that can give damage to operation of the device. In case of
leakage cause from overpressure of heating system, place water colleting
channel that has suitable discharge pipe under safety valve. There is no need
to have safety valve for tap water cycle but be sure that waterworks is not
exceed the 6 bar. If you suspect about this, you can have pressure reduce
valve installed.
Device installation place must be far way from blockers, obstruction parts and
bulges during repairing and maintenance.
Electric connection of the device must be made with suitable cable, fuse and
residual current device and grounding absolutely must be made.
Installation wall of the device must be as durable as carrying the weight of the
device.
From under and upper part of the device ,drill min 2 pcs suitable diameter
holes to the place which is chosen as suitable according to clauses
determined above. Fasten suitable fixing plugs to holes. Screw the device to
holes from up and down. Screw from more point when it is needed.
Heating system must be drawn with suitable diameter pipe for providing
enough circulation of heating water. Choosing radiatorpipes smaller than it is
5.2 WALL INSTALLATION OF DEVICE
5. 2.1 Connection of Heating System and Plumbing

needed, fitting constriction or blockage can cause inability circulation of
heating. Connections that are made to device must be easy removable when it
is needed. Valve and silt trap must be used for water and radiator inlet pipe.
After hydraulic connections are made, filling the heating system is necessary.
For models of UKDAX –xxEDT and UKDAX –xxEDM this process is made
with filling tap under the device. This process must be done byimplementing
following instructions.
 Be sure cold water inlet tap is open.
 Open filling tap until water pressure indicator comes between 1 and 1, 5
bar.
 Close the filling tap when filling is completed.
 When the air collected inside radiators is discharged, it can be reduce at
radiator water pressure. Be sure by checking radiator water pressure is
between 1 and 1, 5bar. If there is decrease, it must be completed by
opening filling tap.
 It must be checked studiously if there is water leakage or not.
5.2.1.1 Filling Heating System for Models of EDT and EDM

After hydraulic connections are made, filling the heating system is necessary.
For the model of UKDAX –xxET Tand UKDAX –xxEDM this process is made
with filling valve connected to heating system. For this, connection with valve
must be made from cold water installation to heating system. This valve must
placed near place to device because of it will be used for filling the heating
system and must be position as it can be seen pressure indicator when the
5.2.1.2 Filling Heating System for Models of ETT and ETM

device is opened. Silt trap is needed after filling valve. Filling process must be
done by implementing following instructions.
 Open filling tap until water pressure indicator comes between 1 and 1, 5
bar.
 Close the filling tap when filling is completed.
 When the air collected inside radiators is discharged, it can be reduce at
radiator water pressure. Be sure by checking radiator water pressure is
between 1 and 1, 5bar. If there is decrease, it must be completed by
opening filling tap.
 It must be checked studiously if there is water leakage or not.
Electrical installation must be done by authorized person according to device
capacity and with suitable diameter cable which is determined according to
cable length. Electrical installation must have suitablespecification for cut off
boiler power and residual current device that has ampere value and fuse
separately. Fuse must be near to device. Grounding of device must absolutely
be done. If there is not grounding at the place that device was installed,
grounding must be made for device authorized person. Grounding must be
controlled if it is operative or not by authorized personnel in determined period.
Fuse must be located near the device; there must be cable after fuse which is
enough as making connection to device. Connection of cables to device must
be made by authorized personnel.
Cable diameter that is calculated according to device capacity and cable
length, residual current device and fuse values can be seen at the following
table.
5.2.2 ELECTRICAL CONNECTIONS

Model
Power(k W)
DrawCurre
ntT
(A)
Fuse and
Residual
Current
Device
(
A
)
Section
Model
Power(k W)
Draw
Curren t
Fuse and
Residual
Current
DeviceA)
Section
3~400 V. 50 Hz Electrical Heating and Hot Water
3~400 V.50 Hz Electrical Only Heating
UKDAX
10EDT
10 3*15,2 3*16
5*2,5
UKDAX
10ETT
10 3*15,2 3*16
5*2,5
UKDAX
12EDT
12 3*18,2 3*20
5*2,5
UKDAX
12ETT
12 3*18,2 3*20
5*2,5
UKDAX
16EDT
16 3*24,3 3*25
5*2,5
UKDAX
16ETT
16 3*24,3 3*25
5*2,5
UKDAX
18EDT
18 3*27,3 3*32
5*4
UKDAX
18ETT
18 3*27,3 3*32
5*4
UKDAX
20EDT
20 3*30,4 3*40
5*4
UKDAX
20ETT
20 3*30,4 3*40
5*4
UKDAX
24EDT
24 3*36,4 3*50
5*6
UKDAX
24ETT
24 3*36,4 3*40
5*6
UKDAX
30EDT
30 3*45,5 3*63
5*10
UKDAX
30ETT
30 3*45,5 3*50
5*10
UKDAX
36EDT
36 3*54,6 3*63
5*10
UKDAX
36ETT
36 3*54,6 3*63
5*10
UKDAX
40EDT
40 3*60,7 3*63
5*16
UKDAX
40ETT
40 3*60,7 3*63
5*16
UKDAX
48EDT
48 3*72,8 3*80
5*16
UKDAX
48ETT
48 3*72,8 3*80
5*16
1~220 V.50 Hz Electrical Heating and Hot Water 1~220 V.50 Hz Only Electrical Heating
UKDAX
10EDM
10 1*45,5 1*50
3*6
UKDAX
10ETM
10
1*45,5 1*50
3*6
UKDAX
12EDM
12 1*54,6 1*63
3*10
UKDAX
12ETM
12
1*54,6 1*63
3*10
UKDAX
16EDM
16 1*72,8 1*80
3*16
UKDAX
16ETM
16
1*72,8 1*80
3*16
UKDAX
18EDM
18 1*81,9 1*100
3*16
UKDAX
18ETM
18
1*81,9 1*100
3*16

Operating Condition and settings of the device can be follow from LCD panel.
Radiator operation indicator
Days of week
Time programming. Can be made 3 pcs time programming
Hour
Capacity indicator
Ready to Operation indicator
6. OPERATION AND USING OF THE DEVICE
6.1 LCD DISPLAY

Water heating indicator
Radiator heating indicator
Over Heating Indicator
Over Heating Difference Value
Pump operation indicator
Freezing prevention indicator
Room ThermostatConnection indicator
Temperature indictor
Use knobs located under LCD display for boiler using.
6.2 FUNCTION KNOBS

ON / OFF
Menu Exit / changing
Temperature increase / up
Temperature decreasing /down
Reset / Timer ON OFF
First operation of the device must absolutely made by Authorized
Service.
Our company is not responsible from damages and accidents which
can be occur associated with intervention to device by unauthorized people.
Before operating the device, suitability of all connections of mechanics and
electrical must be controlled. Heating system must have between1 and 2 bar
pressure flowage for device.Our company is not responsible from damages
and accidents which can be occur because of wrong connection.
Follow following points for the operation of device.
6.3 Operation of the Device

Be sure device water and radiator valves are open. (Only radiator valve is
open for ETT and ETM models.)
Be sure that fuse andresidual current deviceare positioned as preventing
electric transition.
After you open enough insulation from head of electrical cables, place whole
conductive part of cable by loosening connection terminal occurred at device
and tightens cable holder screw as not looseness. Be sure that cable fastens
to its place as completely and solidly. Complete the connection by doing same
process for other cables.
Be sure that cables were connected to correct places.
Loosen cable connections can be caused accidents. Open residual
current device the fuse. After all indicating lights are seen within a few
seconds, LCD display will be as in the following.
Keep press 2 seconds. If setting heating mode of the device was
radiator modebefore it is OFF,after pump is operated about 1 min, device start
to radiator heat and sign is seen inside display. If the setting of the
device was water heating before it is OFF, it stays in standby mode for hot
water using. Warning beep is heard after every pressing knob process. For
long time pressing knobs (for example 2-3 seconds), before hearing warning
beep, it does not mean pressing knob.

1. Bring the device “OFF” position.
2. Keep press button 5-6 seconds, days start to blink, day setting
makes with or buttons.
3. Press button,hour blinks time setting between 0 and 23is done by
pressing orbuttons.
4. Press button minute blinks, minute setting between 0 and 60 is done
by pressing or buttons.
5. By pressing button or not pressing any button for a 10 second ,
exit from setting menu by saving settings.
While the device is operating for heating, can be set between 35 and 80
degree by pressing or buttons. While it was making
6.4 OPERATION PARAMETER SETTINGS
6.4.1 DAY AND TIME SETTING
6.4.2 RADIATOR HEATING SETTING

radiator temperature set, “WATER TEMPERATURE “expression fizzle
out and setting temperature starts to blinks. Two seconds later after
setting is completed, device operation temperature is seen in LCD and
“WATER TEMPERATURE” also seen in LCD. Reaching setting
temperature of the device can take a time.
Bath water temperature can be made in 3 ways. These are;
1. While tap water is flowing, setting can be made by or buttons.
2. If the device is only set for hot water (summer mode), setting can be
made by or buttons while standby mode or operation mode.
3. After the device is only taken to hot water heating mode (summer
mode),setting can be made. For this after it is pressed 2-3
seconds, after pressed
“Shower” is chosen with or then press to Thus the device is
taken to summer mode. After that,temperature setting is made with
and buttons (after the process, device must be again taken to first
operation mode).
During the setting time, heating temperature blinks. Two seconds later
after setting is completed, device operation temperature is seen at the display
and “WATER TEM” is seen at the display.
6.4.3 SETTING TAP WATER TEMPERATURE

While the device reaches to overheat temperature mode, it can be set
temperature difference which is wanted to operate.
While the device is operating regularly,
1. Enter setting menu by pressing button 2-3 seconds.
2. Press to button is seen,ΔT temperature difference starts to
blink.
3. ΔT temperature difference value is set with or buttons.
4. Exit setting menu by pressing button.
It is possible to control device with room thermostat thus the device is
operate according to ambient temperature which room thermostat
occurs. While the device which will make room thermostat connection is
starting-up by authorized service, room thermostat connection will be
activated from inside of device. After room thermostat connection is
done to the device, it is needed to room thermostat bring into use from
setting menu. Although room thermostat is connected, if it is not brought
into use from setting menu, it is not function. While the room thermostat
is not connected,if it is brought into use, device is continuously stood by
for heating and radiator does not operate. When the device room
thermostat function is set as ON, is seen.
While the device is operating regularly,
1. Enter setting menu by pressing button 2-3 seconds.
2. Press button 2 times. is seen , room thermostat
ON/OFF indicator blinks
6.4.4 MAKING ΔT TEMPERATURE DIFFERENCE SETTING
6.4.5 MAKING ROOM THERMOSTAD SETTING