DaytonAudio SUB-1000 User manual

10" 100W
POWERED
SUBWOOFER
Model: SUB-1000 User Manual
Dayton Audio®Last Revised: 3/20/2015
daytonaudio.com
tel + 937.743.8248
[e-mail]
705 Pleasant Valley Dr.
Springboro, OH 45066
USA
Warranty Information
Dayton Audio products are warranted free from defects in material and workmanship for 5 years
from date of purchase. 1 year warranty applies to the following products: powered subwoofers and
electronic devices (e.g. subwoofer amplifiers, and plate amplifiers, as well as the Omnimic V2 and
DATS loudspeaker testing devices). In the rare case of a product failure, please contact your place
of purchase or call our Customer Support Department at [phone].
Warranty Limitations
There are no other warranties, either expressed or implied, that extend the foregoing, and there
are no warranties of merchantability or fitness for any particular purpose. Dayton Audio is not
responsible for any consequential or inconsequential damage to any other unit or component or the
cost for installation or extraction of any component of the audio system, or for the improper use of
products. This includes but is not limited to burnt voice coils, overheating, bent frames, holes in the
cone, or broken lead wires.
This warranty gives you specific legal rights and you may also have other rights that vary from state
to state.
Non-Warranty Service: If non-warranty service is required, the product may be sent to the
Company for repair/replacement, transportation prepaid, by calling [phone] for details,
complete instructions, and service fee charges.

Thank you for purchasing the Dayton Audio®SUB-1000 10" Powered Subwoofer.
It is the perfect addition to any home theater system. This powered sub features a
bottom firing flared port bass reflex design for reduced port noise and increased
bass response. It also utilizes a long throw 10" woofer and up to 100 watts of house
shaking power. This compact sub is finished in a non-obtrusive black veneer that will
complement any decor.
Hookup
1. Line Level Inputs
The line level inputs are used to connect pre-out or preamplifier outputs directly
to the subwoofer amplifier’s internal crossover. These inputs are summed to
mono. This is the preferred way to connect the subwoofer amplifier. If you
have a mono line level signal from a “Pro Logic”or “Dolby Digital” receiver
use the right “red” input. Note: If a LFE mono output is connected, set the
crossover point to maximum.
2. High Level Inputs
If preamplifier outputs are not available, use the high-level (speaker) inputs. The
speaker level inputs can be connected directly to the amplifier by inserting the
speaker wire.
3. High Level Outputs
There are also high level outputs that can be used to connect to main speakers or
to another powered subwoofer with high level inputs. Note: High level outputs
are paralleled to the high level inputs with no high pass filter.
4. Crossover Frequency Control:
Continuously variable from 40 Hz to 140 Hz at 12 dB/octave. Set the frequency
control to where the audio does not sound “muddy”, normally between 60-80 Hz.
Note: If a LFE mono output is connected set the crossover point to maximum.
5. Gain Control:
Adjusts the output level of the subwoofer. Set the level to where the bass
frequencies blend with the other speakers. Note: Most people have a
tendency to set the level too high which, makes the audio sound “boomy”.
6. Phase Switch:
Selectable between 0° and 180°. This assists subwoofer placement. The
correct position will be the one that provides the greatest apparent bass output.
7. Power Switch (Auto On/Off):
When the power is in the auto position, the amplifier will automatically turn on
when a signal is present. Note: In auto/off mode, the power on LED is always on
(red), even when amp is in rest mode (off). The power LED will turn green when
the unit is activated.
Room Placement
The SUB-1000 Subwoofer
System will produce more
bass when it is placed
in a corner. Choose a
corner that is close to the
component area and place
it at the front of the listening
area. See diagram:
Specifications
Dimensions: 14-3/4" H x
14-3/16" W x 15-3/4" D
Frequency Response:
30 Hz-140 Hz
Woofer: 10" long throw
Power: 100W
Voltage: 120 VAC / 60 Hz
Net weight: 32 lbs.