DB Drive Okur A6 800.4 User manual

Due to continuous improvement of the product the Specifications are subject to change without notice.
A6 800.4, A6 1200.4, A6 1600.4, A6 1600.1D,
A6 1900.1D, A6 2800.1D

Low Impedance Stability
A6 800.4 - 2 Ohms Stereo (4 Channel)
A6 1200.4 - 2 Ohms Stereo (4 Channel)
A6 1600.4 - 2 Ohms Stereo (4 Channel)
A6 1600.1D - 1 Ohm Mono
A6 1900.1D - 1 Ohm Mono
A6 2800.1D - 1 Ohm Mono
Bass Boost
For added low frequency performance the amplifiers are equipped with a selectable 6dB-12dB
bass boost @ 45Hz
slope crossover network. Channels 1 and 2 are 12db slope forthe Highpass setting and
channels 3 and 4 feature a selectable 12db slope on the Highpass setting and 12db or 24db
slope on the Lowpass / Bandpass setting.

A6 1600.1D, A6 1900.1D, and A6 2800.1D

A6 800.4, A6 1200.4, A6 1600.4

network that allows you to select the crossover mode (Highpass—Full Range) and desired
crossover point for channels 1 and 2. Channels 3 and 4 allow you to select between a
Highpass 12db slope, a 12db Stereo Lowpass / Bandpass slope and a mono 24db Lowpass /
Bandpass slope. For example if you wish to drive a pair of subwoofers on channels 3 and 4
out the high frequencies with a 24db slope. You will then need to adjust the Lowpass
control to the desired frequency setting (make sure to have the Highpass control set to
switch to LP/BP stereo. Once the LP/BP stereo switch setting is selected you will use both
any unwanted low frequencies with a 12db slope.
The A6 1600.1D, A6 1900.1D and A6 2800.1D are equipped with a variable 24db slope
feature a variable Bass Boost EQ is set at 45Hz. In some subwoofer enclosure installations it
may necessary to use the Phase Shift feature. The Phase Shift button sets the Subwoofer
subwoofer enclosure. All A6 mono amps are also equipped with Multi-Linking technology.
When using a single A6 mono amp set the Master / Slave switch to the Master position.
the slave setting the front panel controls become inoperative. All adjustments for both
( A6 800.4, A6 1200.4, A6 1600.4 ) ( A6 1600.1D, A6 1900.1D, A6 2800.1D )
Master Amp
Slave Amp
Select Master
Select Slave
RCA input Master controls
Slave controls are void
+
2 ohm minimum
Multi-Link
Diagram

Peak @ 14.4V :
2ohm
Frequency Resp.
S/N Ra o (A-weight)
THD with 80k filter
Low Input Level
Crossover Freq.
Bass EQ
Bass Remote Capability
Input Voltage
A6 1600.1D
1 x 800 W
1 x 1600W
15Hz - 250Hz 15Hz - 250Hz 15Hz - 250Hz
Rated Power @ 1 Ohm
>95dB
<0.5%
285mV - 6V
50Hz - 150Hz
0dB - 18dB @ 45Hz
Yes
11.2V - 14.4V
A6 1900.1D
1 x 950 W
1 x 1900W
>95dB
<0.5%
285mV - 6V
50Hz - 150Hz
0dB - 18dB @ 45Hz
Yes
11.2V - 14.4V
A6 2800.1D
1 x 1400 W
1 x 600 W 1 x 900 W 1 x 2050 W
1 x 2800W
>95dB
<0.5%
285mV - 6V
50Hz - 150Hz
0dB - 18dB @ 45Hz
Yes
11.2V - 14.4V
1ohm
Dimensions
A6 800.4
A6 1200.4
A6 1600.4
A6 1600.1D
A6 1900.1D
A6 2800.1D
Height
2.5in/64mm
2.5in/64mm
2.5in/64mm
2.5in/64mm
Width
8.36in/213mm
8.36in/213mm
8.36in/213mm
8.36in/213mm
Length
12.59in/320mm
14.17in/360mm
15.74in/400mm
9.84in/340mm
2.5in/64mm
2.5in/64mm
8.36in/213mm
8.36in/213mm
11.81in/260mm
16.29in/340mm
Peak @ 14.4V :
4 ohms
4ohms bridged
Rated Power @ 4 Ohm
S/N Ra o (A-weight)
THD with 80k filter
Low Input Level
Ch 3&4 High Pass Filter
Bass EQ
Bass Remote Capability
Input Voltage
Ch 3&4 Low Pass Filter
A6 800.4
4 x 180 W
2 x 300 W
4 x 75 W 4 x 95 W 4 x 125 W
Frequency Resp. 15Hz - 25KHz 15Hz - 25KHz 15Hz - 25KHz
>95dB
<0.5%
285mV - 6V
15Hz - 500Hz
0dB,6dB,12dB @ 45Hz 0dB,6dB,12dB @ 45Hz 0dB,6dB,12dB @ 45Hz
11.2V - 14.4V
4 x 90 W
A6 1200.4
4 x 225 W
2 x 500 W
>95dB
<0.5%
285mV - 6V
11.2V - 14.4V
4 x 110 W
A6 1600.4
4 x 300 W
2 x 600 W
>95dB
<0.5%
285mV - 6V
Ch 1&2 High Pass Filter 50Hz - 3KHz
50Hz - 3KHz
15Hz - 500Hz
50Hz - 3KHz
50Hz - 3KHz
15Hz - 500Hz
50Hz - 3KHz
50Hz - 3KHz
11.2V - 14.4V
4 x 150 W
2 ohms