DB Drive Speed SA600.4 User manual

Due to continuous improvement of the product the Specifications are subject to change without notice.
SA600.4, SA800.4, SA1600.4
SA1300.1D, SA1600.1D, SA2000.1D, SA3000.1D
AMPLIFIERS
LIMITED WARRANTY
DB Drive warrants any products purchased in the U.S.A.
from an authorized DB Drive dealer. All products are warranted to
be free from defects in material and workmanship under normal
use and service for a period of two (2) years when the unit is
installed by an authorized DB Drive dealer. Non-authorized dealer
installed products carry a one (1) year parts and labor limited
warranty. This warranty applies to the original purchase only.
DB Drive will either repair or replace (as its option) any
unit that had been found to be defective and under warranty
provided the defect occurs within:
Two (2) years, if purchased through an authorized DB Drive
dealer with original proof of purchase.
This limited warranty periods do not extend to units having been
subjected to misuse, abuse, neglect, or accident. Products that in
DB Drive’s judgment shows evidence of having been altered,
modified, or serviced without DB Drive’s authorization, will be
ineligible under this warranty.
To obtain warranty services please contact your retailer or visit
our website at www.dbdrive.net for more details.
All manuals and user guides at all-guides.com
all-guides.com

All manuals and user guides at all-guides.com

Low Impedance Stability
SA 600.4 - 2 Ohm Stereo (4 Channel)
SA 800.4 - 2 Ohm Stereo (4 Channel)
SA 1600.4 - 2 Ohm Stereo (4 Channel)
SA 1600.1D - 1 Ohm Mono
SA 1300.1D - 1 Ohm Mono
SA 2000.1D - 1 Ohm Mono
SA 3000.1D - 1 Ohm Mono
Bass Boost
For added low frequency performance the amplifiers are equipped with a selectable 6dB-12dB
bass boost @ 45Hz
The DB Drive 4 Channel ampliers (SA 600.4 , SA 800.4 and SA 1600.4) feature a selectable slope
crossover network. Channels 1 and 2 are 12dB slope for the Highpass setting and Channels 3
and 4 feature a selectable 12dB slope on the Highpass setting or 24dB slope on the Lowpass /
Bandpass setting.
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

SA 1300.1D, SA 1600.1D, SA 2000.1D and SA 3000.1D
All manuals and user guides at all-guides.com

SA 600.4, SA 800.4, SA 1600.4
All manuals and user guides at all-guides.com
all-guides.com

n
SA 600.4, SA 800.4 and SA 1600.4 ampliers are equipped with a variable crossover The SA 1300.1D, SA 1600.1D, SA 2000.1D and SA 3000.1D are equipped with a variable 24dB Slope
etwork that allows you to select the crossover mode (Highpass—Full Range) and desired
crossover point for channels 1 and 2. Channels 3 and 4 allow you to select between a
Highpass 12db slope, a 12db Stereo Lowpass / Bandpass slope and a mono 24db Lowpass /
Bandpass slope. For example if you wish to drive a pair of subwoofers on channels 3 and 4
out the high frequencies with a 24db slope. You will then need to adjust the Lowpass
control to the desired frequency setting (make sure to have the Highpass control set to
switch to LP/BP stereo. Once the LP/BP stereo switch setting is selected you will use both
any unwanted low frequencies with a 12db slope.
feature a variable Bass Boost EQ is set at 45Hz. In some subwoofer enclosure installations it
may necessary to use the Phase Shift feature. The Phase Shift button sets the Subwoofer
subwoofer enclosure. All SA
SA
mono amps are also equipped with Multi-Linking technology.
When using a single SA mono amp set the Master / Slave switch to the Master position.
the slave setting the front panel controls become inoperative. All adjustments for both
( SA 600.4, SA 800.4, SA 1600.4 ) ( SA 1300.1D, SA 1600.1D, SA 2000.1D, SA 3000.1D )
Master Amp
Slave Amp
Select Master
Select Slave
RCA input Master controls
Slave controls are void
2 ohm minimum
Multi-Link
Diagram
All manuals and user guides at all-guides.com

Peak @ 14.4V :
2ohms
Frequency Resp.
S/N Rao (A-weight)
THD with 80k filter
Low Input Level
Crossover Freq.
Bass EQ
Bass Remote Capability
Input Voltage
SA 1600.1D
1 x 800 W
1 x 1600W
15Hz - 250Hz 15Hz - 250Hz 15Hz - 250Hz
>95dB
<0.5%
285mV - 6V
50Hz - 150Hz
0dB - 18dB @ 45Hz
Yes
11.2V - 14.4V
SA 2000.1D
1 x 1000 W
1 x 2000W
>95dB
<0.5%
285mV - 6V
50Hz - 150Hz
0dB - 18dB @ 45Hz
Yes
11.2V - 14.4V
SA 3000.1D
1 x 1500 W
SA 1300.1D
1 x 650 W
1 x 1300W
15Hz - 250Hz
>95dB
<0.5%
285mV - 6V
50Hz - 150Hz
0dB - 18dB @ 45Hz
Yes
11.2V - 14.4V
1 x 3000W
>95dB
<0.5%
285mV - 6V
50Hz - 150Hz
0dB - 18dB @ 45Hz
Yes
11.2V - 14.4V
1 ohm
Dimensions
SA 600.4
SA 1600.1D
SA 2000.1D
SA 3000.1D
Height
2.17" / 55mm
2.17" / 55mm
2.17" / 55mm
2.17" / 55mm
Width
9.33" / 237mm
9.33" / 237mm
9.33" / 237mm
9.33" / 237mm
9.33" / 237mm
Length
12.99" / 330mm
SA 800.4
SA 1600.4
2.17" / 55mm
2.17" / 55mm
9.33" / 237mm14.49" / 368mm
18.46"/ 469mm
11.42" / 290mm
12.01" / 305mm
19.29" / 490mm
SA 1300.1D
2.17" / 55mm 9.33" / 237mm
13.32" / 336mm
Peak @ 14.4V :
2 ohms
4ohms bridged
S/N Rao (A-weight)
THD with 80k filter
Low Input Level
Ch 3&4 High Pass Filter
Bass EQ
Bass Remote Capability
Input Voltage
Ch 3&4 Low Pass Filter
SA 800.4
4 x 180 W
2 x 300 W
Frequency Resp. 15Hz - 25KHz
>95dB
<0.5%
285mV - 6V
15Hz - 500Hz
0dB,6dB,12dB @ 45Hz
11.2V - 14.4V
4 x 90 W
Ch 1&2 High Pass Filter 50Hz - 3KHz
50Hz - 3KHz
SA 600.4
4 x 140 W
2 x 240 W
15Hz - 25KHz
>95dB
<0.5%
285mV - 6V
15Hz - 500Hz
0dB,6dB,12dB @ 45Hz
SA 1600.4
4 x 300 W
2 x 600 W
15Hz - 25KHz
>95dB
<0.5%
285mV - 6V
15Hz - 500Hz
0dB,6dB,12dB @ 45Hz
11.2V - 14.4V
4 x 150 W
50Hz - 3KHz
50Hz - 3KHz
11.2V - 14.4V
4 x 60 W
50Hz - 3KHz
50Hz - 3KHz
4 ohms
All manuals and user guides at all-guides.com