DecorQuip ROLLER 38 User manual

TECHNICAL SPECIFICATION
ROLLER 38
BATTERY MOTOR
191723
510mm
40mm
CONTROL TYPE
LIMITS
OUTPUT SPEED
RATED TORQUE
RATED VOLTAGE
RATED POWER
RATED CURRENT
RADIO FREQUENCY
IP RATING
LIFTING CAPACITY
MIN. BLIND WIDTH
MOTOR LENGHT
RADIO
ELECTRONIC
(set remotely)
40 rmp
12 V
10 W
0.83 A
1.1 N.m 433.92 MHz
IP44
5.8 Kg
510 mm
590 mm
MOTOR LENGTH
FUNCTIONAL FEATURES
• Bi-Directional Functionality
• Electronic Limit Setting
• Jog Mode
• Program / Operation Button (P1)
• Three Speed Settings (battery motors)
• Built-in Lithium-ion Battery (battery motors)
• Mains / Solar Charging (battery motors)
• Switch Direction
• Built-in Radio Receiver
• Favourite Stop Position
• Internally Stored Settings
• Pair with up to 10 Control Devices
INSTALLATION
1 2
3 4
CHARGING
APPLICABLE FOR BATTERY MOTORS ONLY
The Dream Motors have a built-in battery that utillises
a mains charger 191692 or solar panel 191682 to recharge.

PROGRAMMING
INSTRUCTIONS
PROGRAMMING INSTRUCTIONS
1. DREAM MOTORS/MULTI-CHANNEL REMOTE CONTROL
 
some very clever functionality when they’re coupled with smart devices, but also makes set up and
operation with our Dream Multi-Channel Handheld Remote Control a quick and easy process.
These instructions apply to all bi-directional Dream motors – including all roller, pleated and roman
motors – battery or mains powered.
1a. BUTTON SPECIFICATION
1b. P1 BUTTON SETTINGS
DISPLAY SCREEN
UP
STOP
DOWN
CHANNEL SELECTOR P2 SETTING BUTTONS
BATTERY
P1 BUTTON
ROMAN/PLEATED LV BATTERY MOTOR
ROLLER BLIND 38 BATTERY/MAINS MOTOR
ROLLER BLIND 45 BATTERY/MAINS MOTOR
ROLLER BLIND 55 BATTERY/MAINS MOTOR
The Dream motors come in a few shapes and sizes but the set up and control instructions are identical
for all of them. Crucial to these instructions is the P1 button that can be found on every motor.
The button in recessed into the motor to avoid accidental activation but is easily accessed with a pen
or a similar device.
As well as being utilised in the pairing process, the P1 button can be used to control the blind when an
external control device is unavailable as well as functions such as restoring factory settings.
Press P1
for 1sec
UP / DOWN
/ STOP
Note:
When in jog-mode, holding the up
or down buttons will temproralily provide
continous-moving.
SHORT PRESS FUNCTION
BUTTON SPECIFICATION
1. P1 BUTTON SETTINGS
PROGRAMMING INSTRUCTIONS
1. DREAM MOTORS/MULTI-CHANNEL REMOTE CONTROL
 
some very clever functionality when they’re coupled with smart devices, but also makes set up and
operation with our Dream Multi-Channel Handheld Remote Control a quick and easy process.
These instructions apply to all bi-directional Dream motors – including all roller, pleated and roman
motors – battery or mains powered.
1a. BUTTON SPECIFICATION
1b. P1 BUTTON SETTINGS
DISPLAY SCREEN
UP
STOP
DOWN
CHANNEL SELECTOR P2 SETTING BUTTONS
BATTERY
P1 BUTTON
ROMAN/PLEATED LV BATTERY MOTOR
ROLLER BLIND 38 BATTERY/MAINS MOTOR
ROLLER BLIND 45 BATTERY/MAINS MOTOR
ROLLER BLIND 55 BATTERY/MAINS MOTOR
The Dream motors come in a few shapes and sizes but the set up and control instructions are identical
for all of them. Crucial to these instructions is the P1 button that can be found on every motor.
The button in recessed into the motor to avoid accidental activation but is easily accessed with a pen
or a similar device.
As well as being utilised in the pairing process, the P1 button can be used to control the blind when an
external control device is unavailable as well as functions such as restoring factory settings.
Press P1
for 1sec
UP / DOWN
/ STOP
Note:
When in jog-mode, holding the up
or down buttons will temproralily provide
continous-moving.
SHORT PRESS FUNCTION
Hold P1
for 6sec
Motor
jogs x2 Beeps x2
SLEEP
MODE
Release
P1
SLEEP MODE
SWITCHING DIRECTION
RESTORING FACTORY SETTINGS
Note:
Sleep mode can be utilised to temporariliy deactivate a motors’s radio functionality, allowing
for multiple motors to be added to a shared channel without disruption. Press P1 to restore
functionality.
Hold P1
for 10sec
Motor
jogs x3
Release P1
Beeps x3
DIRECTION
SWITCHED
Note:
Switching direction using the P1 button is only available once a remote has been paired
with the motor.
Hold P1
for 14sec
Motor jogs x4
Beeps x4
FACTORY
SETTINGS
RESTORED
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- OVERVIEW AND P1 FUNCTIONALITY
1c. PAIRING A REMOTE AND INITIAL SETTINGS
Before starting the process of pairing a handheld remote to a Dream motor, choose the channel to
which it is to be paired.
Channel Zero is reserved for simultaneously controlling all blinds paired to a remote and cannot be
used for pairing, programming or other adjustments

Charging a motor from empty will take approximately 6 hours.
PAIRING A REMOTE WITH A MOTOR
SWITCHING DIRECTION
SETTING THE TOP LIMIT
Motor
jogs x1 Motor
beeps x1
Motor
jogs x2
beeps x3
Release
P1 Press for 2sec
within 10s
PAIRING
COMPLETE
Press P1
for 2sec
Note:
After pairing a remote and before setting limits, the motor will be defaulted to jog-mode. To
switch to continuous-mode, see ADVANCED FUNCTIONALITY - SWITCHING BETWEEN JOG
MODE AND CONTINUOUS MODE on page 15.
Note:
Switching direction with a remote device is only possible before setting top and bottom limits.
To switch after limits have been set, see P1 BUTTON SETTINGS - SWITCHING DIRECTION
on page 14.
Press together
for 2sec
DIRECTION
SWITCHED
Motor
jogs x1
Run blind to
top position Press together
for 2sec
TOP
LIMIT SET
Motor jogs x2
Beeps x3

2. PAIRING A REMOTE AND INITIAL SETTINGS
Hold P1
for 6sec
Motor
jogs x2 Beeps x2
SLEEP
MODE
Release
P1
SLEEP MODE
SWITCHING DIRECTION
RESTORING FACTORY SETTINGS
Note:
Sleep mode can be utilised to temporariliy deactivate a motors’s radio functionality, allowing
for multiple motors to be added to a shared channel without disruption. Press P1 to restore
functionality.
Hold P1
for 10sec
Motor
jogs x3
Release P1
Beeps x3
DIRECTION
SWITCHED
Note:
Switching direction using the P1 button is only available once a remote has been paired
with the motor.
Hold P1
for 14sec
Motor jogs x4
Beeps x4
FACTORY
SETTINGS
RESTORED
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- OVERVIEW AND P1 FUNCTIONALITY
Hold P1
for 6sec
Motor
jogs x2 Beeps x2
SLEEP
MODE
Release
P1
SLEEP MODE
SWITCHING DIRECTION
RESTORING FACTORY SETTINGS
Note:
Sleep mode can be utilised to temporariliy deactivate a motors’s radio functionality, allowing
for multiple motors to be added to a shared channel without disruption. Press P1 to restore
functionality.
Hold P1
for 10sec
Motor
jogs x3
Release P1
Beeps x3
DIRECTION
SWITCHED
Note:
Switching direction using the P1 button is only available once a remote has been paired
with the motor.
Hold P1
for 14sec
Motor jogs x4
Beeps x4
FACTORY
SETTINGS
RESTORED
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- OVERVIEW AND P1 FUNCTIONALITY
Hold P1
for 6sec
Motor
jogs x2 Beeps x2
SLEEP
MODE
Release
P1
SLEEP MODE
SWITCHING DIRECTION
RESTORING FACTORY SETTINGS
Note:
Sleep mode can be utilised to temporariliy deactivate a motors’s radio functionality, allowing
for multiple motors to be added to a shared channel without disruption. Press P1 to restore
functionality.
Hold P1
for 10sec
Motor
jogs x3
Release P1
Beeps x3
DIRECTION
SWITCHED
Note:
Switching direction using the P1 button is only available once a remote has been paired
with the motor.
Hold P1
for 14sec
Motor jogs x4
Beeps x4
FACTORY
SETTINGS
RESTORED
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- OVERVIEW AND P1 FUNCTIONALITY
WATCH THE VIDEO
1c. PAIRING A REMOTE AND INITIAL SETTINGS
Before starting the process of pairing a handheld remote to a Dream motor, choose the channel to
which it is to be paired.
Channel Zero is reserved for simultaneously controlling all blinds paired to a remote and cannot be
used for pairing, programming or other adjustments

Charging a motor from empty will take approximately 6 hours.
PAIRING A REMOTE WITH A MOTOR
SWITCHING DIRECTION
SETTING THE TOP LIMIT
Motor
jogs x1 Motor
beeps x1
Motor
jogs x2
beeps x3
Release
P1 Press for 2sec
within 10s
PAIRING
COMPLETE
Press P1
for 2sec
Note:
After pairing a remote and before setting limits, the motor will be defaulted to jog-mode. To
switch to continuous-mode, see ADVANCED FUNCTIONALITY - SWITCHING BETWEEN JOG
MODE AND CONTINUOUS MODE on page 15.
Note:
Switching direction with a remote device is only possible before setting top and bottom limits.
To switch after limits have been set, see P1 BUTTON SETTINGS - SWITCHING DIRECTION
on page 14.
Press together
for 2sec
DIRECTION
SWITCHED
Motor
jogs x1
Run blind to
top position Press together
for 2sec
TOP
LIMIT SET
Motor jogs x2
Beeps x3

1c. PAIRING A REMOTE AND INITIAL SETTINGS
Before starting the process of pairing a handheld remote to a Dream motor, choose the channel to
which it is to be paired.
Channel Zero is reserved for simultaneously controlling all blinds paired to a remote and cannot be
used for pairing, programming or other adjustments

Charging a motor from empty will take approximately 6 hours.
PAIRING A REMOTE WITH A MOTOR
SWITCHING DIRECTION
SETTING THE TOP LIMIT
Motor
jogs x1 Motor
beeps x1
Motor
jogs x2
beeps x3
Release
P1 Press for 2sec
within 10s
PAIRING
COMPLETE
Press P1
for 2sec
Note:
After pairing a remote and before setting limits, the motor will be defaulted to jog-mode. To
switch to continuous-mode, see ADVANCED FUNCTIONALITY - SWITCHING BETWEEN JOG
MODE AND CONTINUOUS MODE on page 15.
Note:
Switching direction with a remote device is only possible before setting top and bottom limits.
To switch after limits have been set, see P1 BUTTON SETTINGS - SWITCHING DIRECTION
on page 14.
Press together
for 2sec
DIRECTION
SWITCHED
Motor
jogs x1
Run blind to
top position Press together
for 2sec
TOP
LIMIT SET
Motor jogs x2
Beeps x3
1c. PAIRING A REMOTE AND INITIAL SETTINGS
Before starting the process of pairing a handheld remote to a Dream motor, choose the channel to
which it is to be paired.
Channel Zero is reserved for simultaneously controlling all blinds paired to a remote and cannot be
used for pairing, programming or other adjustments

Charging a motor from empty will take approximately 6 hours.
PAIRING A REMOTE WITH A MOTOR
SWITCHING DIRECTION
SETTING THE TOP LIMIT
Motor
jogs x1 Motor
beeps x1
Motor
jogs x2
beeps x3
Release
P1 Press for 2sec
within 10s
PAIRING
COMPLETE
Press P1
for 2sec
Note:
After pairing a remote and before setting limits, the motor will be defaulted to jog-mode. To
switch to continuous-mode, see ADVANCED FUNCTIONALITY - SWITCHING BETWEEN JOG
MODE AND CONTINUOUS MODE on page 15.
Note:
Switching direction with a remote device is only possible before setting top and bottom limits.
To switch after limits have been set, see P1 BUTTON SETTINGS - SWITCHING DIRECTION
on page 14.
Press together
for 2sec
DIRECTION
SWITCHED
Motor
jogs x1
Run blind to
top position Press together
for 2sec
TOP
LIMIT SET
Motor jogs x2
Beeps x3
SETTING THE BOTTOM LIMIT
SWITCHING FROM CONTINUOUS MODE TO JOG MODE
Run blind to
bottom
position
BOT TOM
LIMIT SET
Motor jogs x2
Beeps x3
Press together
for 2sec
Note:
After setting top and bottom limits, the motor will automatically switch to continuous mode.
To switch to jog mode, see ADVANCED FUNCTIONALITY - SWITCHING BETWEEN JOG MODE
AND CONTINUOUS MODE on page 15.
Note:
When in jog mode, holding the up or down buttons will provide continuous-moving temporarily.
1d. ADVANCED SETTINGS
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- PAIRING A REMOTE AND INITIAL SETTINGS
Hold together
for 5sec Press for
1sec
Motor
jogs x1 Motor jogs x1 Beeps x1
JOG
MODE
SETTING THE BOTTOM LIMIT
SWITCHING FROM CONTINUOUS MODE TO JOG MODE
Run blind to
bottom
position
BOT TOM
LIMIT SET
Motor jogs x2
Beeps x3
Press together
for 2sec
Note:
After setting top and bottom limits, the motor will automatically switch to continuous mode.
To switch to jog mode, see ADVANCED FUNCTIONALITY - SWITCHING BETWEEN JOG MODE
AND CONTINUOUS MODE on page 15.
Note:
When in jog mode, holding the up or down buttons will provide continuous-moving temporarily.
1d. ADVANCED SETTINGS
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- PAIRING A REMOTE AND INITIAL SETTINGS
Hold together
for 5sec Press for
1sec
Motor
jogs x1 Motor jogs x1 Beeps x1
JOG
MODE
WATCH THE VIDEO
SWITCHING FROM JOG MODE TO CONTINUOUS MODE
INCREASING MOTOR SPEED
BATTERY MOTORS ONLY
DECREASING MOTOR SPEED
BATTERY MOTORS ONLY
SETTING A FAVOURITE STOP POSITION
Hold together
for 5sec Press for
1sec
Motor
jogs x1 Motor jogs x2
Beeps x3
CONTINUOUS
MODE
Note:
When in jog mode, holding the up or down buttons will provide continuous-moving temporarily.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Press for
1sec
Motor jogs x2
Beeps x1
SPEED
INCREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Motor jogs x2
Beeps x1
SPEED
DECREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Press for
1sec
Motor jogs x1
Beeps x1
Run shade to
desired position Press P2
for 1sec
Press
for 1sec
FAVOURITE
POSITION
SET
Motor jogs x1
Beeps x1 Motor jogs x1 Beeps x1
Press
for 1sec
Motor jogs x2
Beeps x3

SETTING THE BOTTOM LIMIT
SWITCHING FROM CONTINUOUS MODE TO JOG MODE
Run blind to
bottom
position
BOT TOM
LIMIT SET
Motor jogs x2
Beeps x3
Press together
for 2sec
Note:
After setting top and bottom limits, the motor will automatically switch to continuous mode.
To switch to jog mode, see ADVANCED FUNCTIONALITY - SWITCHING BETWEEN JOG MODE
AND CONTINUOUS MODE on page 15.
Note:
When in jog mode, holding the up or down buttons will provide continuous-moving temporarily.
1d. ADVANCED SETTINGS
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- PAIRING A REMOTE AND INITIAL SETTINGS
Hold together
for 5sec Press for
1sec
Motor
jogs x1 Motor jogs x1 Beeps x1
JOG
MODE
SETTING THE BOTTOM LIMIT
SWITCHING FROM CONTINUOUS MODE TO JOG MODE
Run blind to
bottom
position
BOT TOM
LIMIT SET
Motor jogs x2
Beeps x3
Press together
for 2sec
Note:
After setting top and bottom limits, the motor will automatically switch to continuous mode.
To switch to jog mode, see ADVANCED FUNCTIONALITY - SWITCHING BETWEEN JOG MODE
AND CONTINUOUS MODE on page 15.
Note:
When in jog mode, holding the up or down buttons will provide continuous-moving temporarily.
1d. ADVANCED SETTINGS
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- PAIRING A REMOTE AND INITIAL SETTINGS
Hold together
for 5sec
Press for
1sec
Motor
jogs x1 Motor jogs x1 Beeps x1
JOG
MODE
SWITCHING FROM JOG MODE TO CONTINUOUS MODE
INCREASING MOTOR SPEED
BATTERY MOTORS ONLY
DECREASING MOTOR SPEED
BATTERY MOTORS ONLY
SETTING A FAVOURITE STOP POSITION
Hold together
for 5sec
Press for
1sec
Motor
jogs x1 Motor jogs x2
Beeps x3
CONTINUOUS
MODE
Note:
When in jog mode, holding the up or down buttons will provide continuous-moving temporarily.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Press for
1sec
Motor jogs x2
Beeps x1
SPEED
INCREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Motor jogs x2
Beeps x1
SPEED
DECREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Press for
1sec
Motor jogs x1
Beeps x1
Run shade to
desired position Press P2
for 1sec
Press
for 1sec
FAVOURITE
POSITION
SET
Motor jogs x1
Beeps x1 Motor jogs x1 Beeps x1
Press
for 1sec
Motor jogs x2
Beeps x3
SWITCHING FROM JOG MODE TO CONTINUOUS MODE
INCREASING MOTOR SPEED
BATTERY MOTORS ONLY
DECREASING MOTOR SPEED
BATTERY MOTORS ONLY
SETTING A FAVOURITE STOP POSITION
Hold together
for 5sec Press for
1sec
Motor
jogs x1 Motor jogs x2
Beeps x3
CONTINUOUS
MODE
Note:
When in jog mode, holding the up or down buttons will provide continuous-moving temporarily.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Press for
1sec
Motor jogs x2
Beeps x1
SPEED
INCREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Motor jogs x2
Beeps x1
SPEED
DECREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Press for
1sec
Motor jogs x1
Beeps x1
Run shade to
desired position Press P2
for 1sec
Press
for 1sec
FAVOURITE
POSITION
SET
Motor jogs x1
Beeps x1 Motor jogs x1 Beeps x1
Press
for 1sec
Motor jogs x2
Beeps x3
SWITCHING FROM JOG MODE TO CONTINUOUS MODE
INCREASING MOTOR SPEED
BATTERY MOTORS ONLY
DECREASING MOTOR SPEED
BATTERY MOTORS ONLY
SETTING A FAVOURITE STOP POSITION
Hold together
for 5sec Press for
1sec
Motor
jogs x1 Motor jogs x2
Beeps x3
CONTINUOUS
MODE
Note:
When in jog mode, holding the up or down buttons will provide continuous-moving temporarily.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Press for
1sec
Motor jogs x2
Beeps x1
SPEED
INCREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Motor jogs x2
Beeps x1
SPEED
DECREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Press for
1sec
Motor jogs x1
Beeps x1
Run shade to
desired position Press P2
for 1sec
Press
for 1sec
FAVOURITE
POSITION
SET
Motor jogs x1
Beeps x1 Motor jogs x1 Beeps x1
Press
for 1sec
Motor jogs x2
Beeps x3
3. ADVANCED SETTINGS

SWITCHING FROM JOG MODE TO CONTINUOUS MODE
INCREASING MOTOR SPEED
BATTERY MOTORS ONLY
DECREASING MOTOR SPEED
BATTERY MOTORS ONLY
SETTING A FAVOURITE STOP POSITION
Hold together
for 5sec Press for
1sec
Motor
jogs x1 Motor jogs x2
Beeps x3
CONTINUOUS
MODE
Note:
When in jog mode, holding the up or down buttons will provide continuous-moving temporarily.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Press for
1sec
Motor jogs x2
Beeps x1
SPEED
INCREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Motor jogs x2
Beeps x1
SPEED
DECREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Press for
1sec
Motor jogs x1
Beeps x1
Run shade to
desired position Press P2
for 1sec
Press
for 1sec
FAVOURITE
POSITION
SET
Motor jogs x1
Beeps x1 Motor jogs x1 Beeps x1
Press
for 1sec
Motor jogs x2
Beeps x3
FINE-TUNING A TOP LIMIT
CLEARING A FAVOURITE STOP POSITION
FINE-TUNING A BOTTOM LIMIT
ADDING/REMOVING AN EXTRA REMOTE
Hold together
for 5sec Hold together
for 2sec
Jog to desired
position
FINE-TUNE
MODE
ENGAGED
TOP
LIMIT SET
Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
Hold together
for 5sec Hold together
for 2sec
Jog to desired
position
FINE-TUNE
MODE
ENGAGED
BOT TOM
LIMIT SET
Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
REMOTE
PAIRED
Hold
for 2sec
Press P2
for 1sec Press P2 for 1sec
Motor jogs x1
Beeps x1 Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
Existing remote control device Remote control device to add/remove
Press
for 1sec
Press
for 1sec
FAVOURITE
CLEARED
Press P2
for 1sec
Motor jogs x1
Beeps x1 Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- ADVANCED FUNCTIONALITY
FINE-TUNING A TOP LIMIT
CLEARING A FAVOURITE STOP POSITION
FINE-TUNING A BOTTOM LIMIT
ADDING/REMOVING AN EXTRA REMOTE
Hold together
for 5sec
Hold together
for 2sec
Jog to desired
position
FINE-TUNE
MODE
ENGAGED
TOP
LIMIT SET
Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
Hold together
for 5sec Hold together
for 2sec
Jog to desired
position
FINE-TUNE
MODE
ENGAGED
BOT TOM
LIMIT SET
Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
REMOTE
PAIRED
Hold
for 2sec
Press P2
for 1sec Press P2 for 1sec
Motor jogs x1
Beeps x1 Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
Existing remote control device Remote control device to add/remove
Press
for 1sec
Press
for 1sec
FAVOURITE
CLEARED
Press P2
for 1sec
Motor jogs x1
Beeps x1 Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- ADVANCED FUNCTIONALITY
FINE-TUNING A TOP LIMIT
CLEARING A FAVOURITE STOP POSITION
FINE-TUNING A BOTTOM LIMIT
ADDING/REMOVING AN EXTRA REMOTE
Hold together
for 5sec Hold together
for 2sec
Jog to desired
position
FINE-TUNE
MODE
ENGAGED
TOP
LIMIT SET
Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
Hold together
for 5sec
Hold together
for 2sec
Jog to desired
position
FINE-TUNE
MODE
ENGAGED
BOT TOM
LIMIT SET
Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
REMOTE
PAIRED
Hold
for 2sec
Press P2
for 1sec Press P2 for 1sec
Motor jogs x1
Beeps x1 Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
Existing remote control device Remote control device to add/remove
Press
for 1sec
Press
for 1sec
FAVOURITE
CLEARED
Press P2
for 1sec
Motor jogs x1
Beeps x1 Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- ADVANCED FUNCTIONALITY
www.decorquip.com

SWITCHING FROM JOG MODE TO CONTINUOUS MODE
INCREASING MOTOR SPEED
BATTERY MOTORS ONLY
DECREASING MOTOR SPEED
BATTERY MOTORS ONLY
SETTING A FAVOURITE STOP POSITION
Hold together
for 5sec Press for
1sec
Motor
jogs x1 Motor jogs x2
Beeps x3
CONTINUOUS
MODE
Note:
When in jog mode, holding the up or down buttons will provide continuous-moving temporarily.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Note:
If the motor does not response to these instructions, it has already reached its upper speed setting.
Press for
1sec
Motor jogs x2
Beeps x1
SPEED
INCREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Motor jogs x2
Beeps x1
SPEED
DECREASED
Press P2
for 1sec
Press for
1sec
Motor jogs x1
Beeps x1
Press for
1sec
Motor jogs x1
Beeps x1
Run shade to
desired position Press P2
for 1sec
Press
for 1sec
FAVOURITE
POSITION
SET
Motor jogs x1
Beeps x1 Motor jogs x1 Beeps x1
Press
for 1sec
Motor jogs x2
Beeps x3
FINE-TUNING A TOP LIMIT
CLEARING A FAVOURITE STOP POSITION
FINE-TUNING A BOTTOM LIMIT
ADDING/REMOVING AN EXTRA REMOTE
Hold together
for 5sec Hold together
for 2sec
Jog to desired
position
FINE-TUNE
MODE
ENGAGED
TOP
LIMIT SET
Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
Hold together
for 5sec Hold together
for 2sec
Jog to desired
position
FINE-TUNE
MODE
ENGAGED
BOT TOM
LIMIT SET
Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
REMOTE
PAIRED
Hold
for 2sec
Press P2
for 1sec Press P2 for 1sec
Motor jogs x1
Beeps x1 Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
Existing remote control device Remote control device to add/remove
Press
for 1sec
Press
for 1sec
FAVOURITE
CLEARED
Press P2
for 1sec
Motor jogs x1
Beeps x1 Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- ADVANCED FUNCTIONALITY
FINE-TUNING A TOP LIMIT
CLEARING A FAVOURITE STOP POSITION
FINE-TUNING A BOTTOM LIMIT
ADDING/REMOVING AN EXTRA REMOTE
Hold together
for 5sec Hold together
for 2sec
Jog to desired
position
FINE-TUNE
MODE
ENGAGED
TOP
LIMIT SET
Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
Hold together
for 5sec
Hold together
for 2sec
Jog to desired
position
FINE-TUNE
MODE
ENGAGED
BOT TOM
LIMIT SET
Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
REMOTE
PAIRED
Hold
for 2sec
Press P2
for 1sec Press P2 for 1sec
Motor jogs x1
Beeps x1 Motor jogs x1
Beeps x1 Motor jogs x2
Beeps x3
Existing remote control device Remote control device to add/remove
Press
for 1sec
Press
for 1sec
FAVOURITE
CLEARED
Press P2
for 1sec
Motor jogs x1
Beeps x1 Motor jogs x1
Beeps x1
Motor jogs x1
Beeps x1
Visit our YouTube channel for video equivalent
of these instructions.
DREAM RANGE PROGRAMMING INSTRUCTIONS
- ADVANCED FUNCTIONALITY
WATCH THE VIDEO
www.decorquip.com
Get instant access to all information you’ll ever need about our Dream Range
motorisation and become an expert in minutes.
The Dream Range User’s Guide is available for everyone to download and
we encourage you to share it with your clients. Just scan the QR code,
download or print the guide.
From basic product information and functionality to more advanced
setup, our easy to follow and quick to complete step-by-step guide gives
you or your clients an instant solution - no matter where you are.
Find out more about the Dream Range products - from battery motors
and controls to smart home automation options, whatever bespoke
solution you’re looking to create - we’ve got you covered.