DeDietrich DVH1044J User manual

Reviewing the section on troubleshooting Tips will help
you solve some common problems by yourself.
Dear Cu stomer,
Please carefully read this m anual before using the
dishwa sher, it will h elp you t o use and mainta in the
dishwa sher properly.
Pass i t on t o any subseq uent owner of the appliance.
This manual contains se ctions on safety Instr ucti ons,
Op erating I nstr uctio ns, Inst allat ion I nstru ctio ns a nd
Tr oublesho otin g Tip s, etc.
The manufacturer, following a policy of con stant
development and updating of t he product, may
make modifications w itho ut giving prior notice.
If lost o r out-of-date , you can receive a n ew user
manual from the ma nufacturer or responsible
vendor.
Keep this manual for future ref erence.
If you cannot solve the problems by yourself,
please ask for help from a professional technician.
Dis hw asher Fe at ure s... ..... .... ....... ..... .... ........ . ....... 6
A Water Softener.................................... ............7、
................................... .............. . 12
Recommen dations for loadi ng and unlo adi ng
the dish washer
Filter System........................................ ...............16
Caring for the Dishw asher.......... ........... ..............17.
B Loading the Salt into the Softener......................8、
C Filling the Rinse Aid Dispenser......................... 8、
D Function of Dete rgent ......................................9、
Loading the upper ....................................13Basket
Loa ding the Lower ....................................13Basket
Wash Cycle Table................................................14
Turning on the Appliance............................... ......14
...... ............. .....15
Chan ging the Program mid-cycle ..
At the end of the Wash Cycle... .............................15
Befo re calling for service................. .......... ....... ...25.
Error codes.................................... ...................26.
Technical information.............................. ..........27..
Cont rol Panel.......... ..............................................6
Inst allation preparat ion.......... ........................ .....18
........19Aesthetic panel's dimensions and installation
Ten sion ad jus tment of the door spring...................21
Connection of drain hoses...... .................... .... .....21
Dishwasher installation steps......................... .....22
About E lectricity Connecting...................... ..........23
Cold Water Connection. ................... .............. .....24

1
This appliance is intended to be used in household
and similar applications such as:
-staff kitchen areas in shops, offices and other
working environments;
-farm houses;
-by clients in hotels, motels and other residential type
environments;
-bed and breakfast type environments.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be done by children
without supervision.(For EN60335-1)
Packaging material could be dangerous for children!
This appliance is for indoor household use only.
To protect against the risk of electrical shock,
do not immerse the unit, cord or plug in water or
other liquid.
Please unplug before cleaning and performing
maintenance on the appliance.
Use a soft cloth moistened with mild soap, and then
use a dry cloth to wipe it again.
When using your dishwasher,
follow the precautions listed below:

2
This appliance must be earthed. In the event of a
malfunction or breakdown, earthing will reduce the
risk of an electric shock by providing a path of least
resistance of electric current. This appliance is
equipped with an earthing conductor plug.
The plug must be plugged into an appropriate outlet
that is installed and earthed in accordance with all
local codes and ordinances.
Improper connection of the equipment-earthing
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded.
Do not modify the plug provided with the appliance;
If it does not fit the outlet.
Have a proper outlet installed by a qualified electrician.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not operate your dishwasher unless all enclosure
panels are properly in place.
Open the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Do not place any heavy objects on or stand on the door
when it is open. The appliance could tip forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely to
damage the door seal;

3
2) Warning: Knives and other utensils with sharp points
must be loaded in the basket with their points
down or placed in a horizontal position.
Check that the detergent powder is empty after
completion of the wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent.
For check the
manufacturer's recommendations.
Use only detergent and rinse agents recommended for
use in an automatic dishwasher.
The door should not be left open, since this could increase
the risk of tripping.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
During installation, the power supply must not be
excessively or dangerously bent or flattened.
Do not tamper with controls.
The maximum number of place settings to be washed
is 10.
The maximum permissible inlet water pressure is 1MPa.
The minimum permissible inlet water pressure is 0.04MPa.
facing
“ ”
unmarked plastic items not so marked,
Never use soap, laundry detergent, or hand washing
detergent in your dishwasher.
The appliance needs to be connected to the main water
valve using new hose sets. Old sets should not be reused.

4
This appliance's packaging materials are recyclable.
Dispose of the packaging into a suitable waste
collection container to recycle it.
It is prohibited to dispose of this appliance as
household waste.
Correct Disposal of this product: this symbol on the
product or in its packing indicates that this product
may not be treated as household waste. Instead,
it should be taken to the appropriate waste collection
point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative
consequences for the environment and human health,
which could otherwise be caused by the inappropriate
waste handling of this product.
For more detailed information about the recycling of
this product, please contact your local council your
household waste disposal service, or the shop where
you purchased the product.
For disposing of package and the appliance please
go to a recycling centre. Therefore cut off the power
supply cable and make the door closing device
unusable.
Cardboard packaging is manufactured from recycled
paper and should be disposed in the waste paper
collection for recycling.
By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences
for the environment and human health, which could
otherwise be caused by inappropriate waste handling
of this product.
For more detailed information about recycling of this
product, please contact your local city office and your
household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted
municipal waste. Collection of such waste separately
for special treatment is necessary.

Check the rinse aid level
(On models with water softener system only.)
Electric indicator on control panel (if provided).
If there is no salt warning light in the control panel
(for some models), you can estimate when to fill the salt into
the softener by the number of cycles the dishwasher has run.
Check the regeneration
salt level
Load the baskets
Select a programme
Turn on the water tap ,close the door . The machine will start working after about 10 seconds.
Running the dishwasher
Switch off the appliance
Turn off the water tap,
unload the baskets
Fill the detergent dispenser
Warning: wait a few minutes (about 15 m inutes ) befo re unloading the dishwasher to avoid
han dling the dishes and uten sils while they are still h ot and more suscep tible t o brea k.
The dishes will also dry bett er. First start unloading th e lower bask et.
Changing the programme
Adding forgotten dishes in
the dishwasher.
To load the baske ts, ref er to th e section entitled Loading the Dishwashe r Bask ets .“ ”
Press the Programme Button until the selected programme lights up.
( See the section entitled Operation instruction )“ ”
When the working cycle has finished, the buzzer of the
dishwasher will sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
If the appliance is switched
off during a wash cycle.
Open the do o r car efu lly.
Look out for hot ste am
when openin g the door!
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).
Switch on the appliance Open the door,press the On/Off button to switch on the appliance .
1.Open the door a little to stop the dishwasher.
2.After the spray arms stop working, you can open the door completely.
3.Add the forgotten dishes.
4.Close the door, the dishwasher will start running again after 10 seconds.
For detailed operating method read the corresponding content on the instruction manual.
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Open the door.
3. Press the for more than 3 seconds to cancel the running programme.
4. Select a new programme.
5. Restart the dishwasher.
Programme Button
5
For each wash cycle.
For programs with pre-wash,please put the detergent anywhere inside the
inner tank except in compartment A
(Follow the user instructions!)
Electric indicator on control panel (if provided).

6
before using it for the first time.
To get the best perform ance from your dishwasher, read all operating instructions
Back View
Front view
1
2
3
4
5
7
6
11
8
Lower basket
Salt container
Dispenser
Cup s helf
Spray arms
Filter assembly
Inle t pipe connector
Drain pipeUpper basket
Cutlery rack
1
Inner pip e
5
6
7
8
9
10
11
3
2
4
9
10
2.
Note:These options can only be applie d to intensive,
normal, ECO, glass and 1 hour programs
3. Dual zone wash function, touch the button to select
eithe r upper basket or lower basket loaded.The
4. D elay Button : Press the b utton
5. Program Button : Press the button to select a
wash Program.
6. On/off Button:
To turn on/off the pow er suppl y.
response indicator will light.
To choose "Extra drying" or "Strong wa sh" function:
Extr a Drying: Final ri nse temp erature increases and
an extended drying phase is adde d to improve drying
efficienc y. It involves a slight energy consumption
incre ase.Strong was h: An increased temperature
duri ng the main w ash and a addit ional rising are
added to improve cleaning efficiency. This function
will involve an energy and water consumption incr ease.
to delay the start of the
wash cycle
1. Dis pla y screen: to sho w t he erro r code ,delay tim e etc.
Program indicators:
Dela y time or error codes indi cator:
Dual zone wash indicators:
Rinse Aid indicator:
Indicates when the dispen ser needs to be refilled.
Add salt indicator:
Indicates when the dispen ser needs to be refilled.
Extra drying i ndicator:
Strongwash function indicators:

The water softener must be set m anually, using the water hardness dial.
The wat er softener is designed to rem ove minerals and salts from the water, which would have
a detrimental or adverse effect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hard ness of the water in your area. Your local Water Authority
can advise you on the hardness o f the water in your ar ea.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed based on the ha rdness of
the water used. This is intended to op timise and customise the level o f salt consumption.
1. Open the door ,Switch on the appliance;
2. Press the Program button for more than 5 seconds to start the water softener
set model wit hin 60seconds after the appliance was switched on( The Salt and
Rinse aid warninglights will be on periodically when it get in the set model );
3. Press the Program button to select the proper set accor ding to your local environment,
th e sets will chang e in the following sequence: H4 H5 H6 H1 H2 H3;→→→→→
4. To end the s etti ng mode , ei t her press the On /Off but ton o r wa it 5 seco nds .
WATER SOFTENER
The hardness of the water varies from place to plac e. If hard water is used in the dishwasher, de posits will
form on the dish es and utensils.
The applian ce i s equipped with a sp ecial softener that uses a salt container specifically des igned to eliminate
lime and minera ls from the water.
Contact your local water board for information on the hardness of your water supply.
Please follow the steps below for adjustment in salt consumpt ion.
7
If your model does not have any water softener, you may skip this section.
Clark: British degree
fH: French degree
DH: German degree
dH=1.25 Clarke=1.78 fH =0.178mmol/l
1
The manufactory setting: H3 (EN 50242)
Before using your dishwasher for the first time:
A. Set the water softener
B. Add 1.5Kg dishw asher salt and then full fill the salt container with water
C. Fill the rinse aid dispenser
D. Fill in detergent
dH mm ol/l
0~90~5 0~0.94 H1 0
10-20 6-11 1.0-2.0 H2 9
21-3012-17 2.1-3.0 H3 12
H4 20
fH
0~6
7-14
15-21
Clark
WAT ER HARDN ESS
Sel ecto r Position Salt consumption
(gram/cycle)
18-22 31-40 2 2-28 3.1-4.0
41-6023-34 4.1-6.0 H5 30
H6 60
29-42
35-55 61-98 4 3-69 6.1-9.8

1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how well the salt dissolves, the salt warning light may still be on even though the
salt container is filled.
If there is no salt warning light in the control panel (for some Mode ls),you can estimate when to fill
the salt into the softener by the cycles that the dishwasher has run.
2. I f sal t has sp illed , run a s oak or q uick pro gram to remove it.
Always use salt intended for dishwasher use
The salt container is located beneath the lowe r basket and should be filled as explained
in the following:
Warning!
Only use salt specif ically designe d for dishwashers use! Every other type of
salt not speci fically designed fo r dishwasher use, e specially table salt, will
damage the w ater softener. In case of damages caused by the use of unsuitable
salt the ma nufacturer does not give any wa rranty nor is liable for any damages caused.
Only fil l with salt just before starting one of the co mplete washing programs.
This wi ll prevent any grains of salt or salty wate r, which ma y have been spilled,
remaining on the bottom of the machine for any period of time, which may cause
corrosion.
8
C. Filling the Rinse Aid Dispenser
Rinse Aid Dispenser
Function of Rinse Aid
Rinse aid is automat ically added during the last rinse, ensuring thorough rinsing, a s pot and streak free drying.
Warning!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dis penser with any other substances
(e.g. Di shwasher cleaning agent, liquid detergent). Th is would damage the app liance.
with water,It is normal for a small amount of water to
come out of the salt container.
Fill the salt cont ainer to it s maximum limit
AAfter the lower basket has been removed, unscrew and remove the cap from the salt container.
BPlace the end of the funnel (supplied) into the hole and about 1.5kg of dishwasher salt .
poor i n
C
DAfter filling the container , screw bac k the cap tightly.
EThe salt warning light will stop being after th e salt container has been fi lled with sa lt.
FImmediat ely aft er filling the salt into the salt container, a washing program should be started
program Other wise the filter system, pump or ot her important parts of the machine may be damaged
by salty water. This is out of warranty.
(We suggest to use a short
).
The rinse aid is released during the final ri nse to prevent water from forming droplets on your dishes, whic h can
leave spots and streaks. It also improves dry ing by allowing water to roll off the dishes. Your dishwasher is
designed to use liquid rinse aids. The rinse a id dispenser is located inside, on the door and next to the detergent dispenser.
To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns c ompletely
black . The v olume of the rinse aid container is about 110m l.

9
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Caref ul ly pour i n the ri nse -aid into it s dispenser, wh ilst avoidin g it to ove rfl ow.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six or four s et tings. Always st art with the dispenser
set on "4". If spot s and poo r drying are a problem, increase the amount of rinse
aid dispensed by removing the dispenser lid and rotating the d ial to "5". If the
dishes still are not drying properly o r show spots, adjust the dial t o the ne xt
high er lever until your dishes are spot-free. The recommen ded setting is "4".
(Factory value is "4".)
Inc rease th e dose if there are drops of water o r lime spots on the dishes a fter washing.
Reduce i t if there are sticky whitish stains on yo ur dish es o r a bluish film on g lassware or
knife blad es .
1
2
3
As the rinse aid d iminishes, the size o f the black dot
on the rinse aid leve l indicator changes, as illustra ted b elow.
Full
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to eliminate spotting
Empty
When to Refill the Rinse Aid Dispenser
Unless the rinse-aid warning light on th e control panel is on, you ca n always est ima te th e amount from t he color
of the optical level indicator "C "loc ated next to the cap. When t he rinse-aid container is full , the indicator
wi ll be fully dark. The size of the dark dot d ecre ases as the rinse-aid diminishes. You should never let
the rinse aid level be le ss than 1/4 full.
during the next wash. Don't forget t o replace the cap be fore you close dishwa sher door.
Clean up with an absorbent cloth to avoid excessive foaming
any spille d rinse aid
The chemical ingredients that compose the detergent are necessary to remove, crush and dispense all dirt out of the
di shwashe r. Most of the commercial quality detergents are suitable for this purpose.
" "
Proper Use of Detergent
Use only detergent specifically m ade for the dishwashers use. Keep your detergent fresh and dry.
Don't put powdered detergent into the dispenser until you are ready to wash dishes.
Warning!

10
Amount of Detergent to Use
Dishwasher detergent is corrosive!
Take care to keep it out of reach of children.
Based on their chem ical composition, deterge nts can be split in two basic types:
Detergent tablets of different brands dissolve at different speeds. For this r eason some
detergent tablets cannot dissolve and develop their full cleaning power during short
prog rams. There fore please use l ong programs when using deterg ent tablets, to
ensure the complete rem oval of detergent residua ls.
The dispenser must be re filled before the start of each wash cycle following the inst ructions
provided in the w ash cycle table . Your dishwa sher uses less detergent and rinse aid than
Conventional dis hwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More heavily soiled it ems need more detergent. Always add the
detergent just be fore starting the dishwas her, otherwise it could get damp and w ill not
dissolve properly.
Concentrated Detergent
Detergent Tablets
Detergent Dispenser
co nventional, alkaline detergents with caus tic components
low al kalin e concentrated detergen ts with n atural enzymes
Normally new pulver ised detergent is without phosphate. T hus the water softener function of
phospha te is not given. In this case we recommend to fill salt in the salt con tainer even w hen
the hardness of water is only 6 dH. If dete rgents without phosphate are used in the case of hard water
often white spots appear on dishes and glasses. In this case please add more detergent to r each
bett er results. Detergents without chlorine do only bleach a little. S tron g and coloured spots will not
be removed completely. In this case please choose a program with a hi gher temperature.
°
Detergents
There are 3 sorts of detergents
1.With phosphate and with chlorine
2.With phosphate and without chlorine
3.Without phosphate and without chlorine
Always add the detergent just before starting each wash cycle.
Only use branded detergent aid for dishwasher.
If the lid is closed: pr ess release button. The lid will spring open.
Dete rgent p owde r

11
Fill the detergent dispenser with detergent.
The marking indicates the dosing levels , as
Illustrated :below
Please observe the manufacturers dosing and storag e
Recommendations as stated on the detergent packaging.
Close the lid and p ress on it until it lock s into place.
If the dishes are heavily soiled, place an addi tional
detergent dose in the pre-wash detergent ch amber. This detergent will take effect during the pre-wash phase.
Filling the detergent dispenser
You information about the amo unt of detergent for the single programme on pag e 14.
will find
Be aware that depending on the soilin g of water, setting may be different.
Please obser ve the manufacturer's rec ommendations on the detergent packaging.
1. Place the main washing cycle detergent in the storage
compartment indicated with an A on the picture.
The marking on the compartment indicates the dosi ng
le vel.
2. Place pre-wash detergent cycle de tergent anywhere
in side the inner tank
“ ”

Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that are not
temperature resistant
Bonded cutler y items or dishes
Pewter or cooper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
Some types of glasses can become
dull after a large number of washes
Silver and aluminum parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
Are not suitable Are of limited suitability
Dishes and items of cutlery must not lie inside one another, or cover each oth er.
The upper basket is designed to ho ld more delicate and lighter dishware such as glasses , coffee
and t ea cups
Long bladed knives stored in an upright position are a potential haza rd!
Long and/or sharp items of cutlery such as carving knives must be positioned
horizonta lly in the upper basket.
Please do not ove rload your dishwasher. This is important for good results and for
reasonable consumption of energy.
To avoid damage, glasse s sho uld not touch one another.
Load large and d ifficult to cle an items in the lower basket.
Load hollow items suc h as cups, gl asses, pans etc. With the opening facing downwards so that
water cannot collect in the container or a deep base.
Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind to dishes'. If necessary, seek further
information from the detergent manufacturers.
For particular items, select a program w ith
To prevent damage, do not take glass and c utlery out of the dishwasher immediately
after the programme has ended.
the lo west po ssible te mperature.
(For best performance of the dishwasher, follow these loading guide lines.
Features and appearance of baskets and cutlery baskets may vary from your model.)
Scrape off any large amounts o f leftover food. Soften remnants of burnt food in pans.
It is not necess ary to rinse t he d ishes under running water.
Place objects in the dishwasher in following way:
1.Item s such as cups, glasses, pots /pans, etc. a re faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so th at water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are placed in the way that the spray arms can rotate freely during washing.
Very sm all items should not be washed in the dishwasher as they could easily fall out of the basket.
To prevent water dripping from the upper basket into the lower basket, we recommend that you
empty the lower basket first upper basket.
, followed b y the
12

13
The u pper basket is designed to hold more delicate
and lighter dishware such as glasses, coffee and
tea cups and saucers, as well as plates, small bowls
and shallow pans (as long as they are not too dirty).
Position the dishe s an d co okware so that they w ill
not get moved by the spray of wate r.
Pots, serving bowls, etc, must alw ays be placed top down.
Deep pots should be slan ted to allow water to flow out.
Please be reminded that:
The B ottom Basket features fo lding spikes so that larger or more pots and pans can be loaded.
Cutlery should be placed in the cutlery rack separately from each other in the appropriate positions, a nd do
make sure the utensils do not nest together, this may cause bad performanc e.
They do not nest together.
Silverware is placed with the male face up.
Long utensils in the middle.
The height of the upper rack can be easily adjusted to
accommodate tal ler dishes in either the upper and lower
rack. To raise the rack to the upper position, lift rack until
both sides are at the same height. The rack will secure
into place. To low er the rack, push down on the handle
and release.
Do not let any item extend through the bottom.
Always load sharp utensils with the
sharp point down!
For better stacking of pots and pans, the spikes can
be folded down as show on the picture .
below
For better stacking of cups, the spikes can be
folde d down as show on the picture below.
We suggest that you place large items and the most
difficult to clea n items such as
pots, pans, lids, serving dishes and bowls, as shown
in the figure below. It is preferable to place serving
dishes and lids on the side of the racks in order to
avoid blocking the rotation of the top spray arm.
int o the low er b aske t:
For a top quality cleaning, place the silverware in the basket making sure that:

Means: need to fill rinse into the Rinse-Aid Dispenser.
( )
*EN 50242 : This programme is the test cycle. The information for comparability test
in accordance with EN 50242, as follows:
Capacity: 10 setting
Position Upper basket :
Rinse aid setting: 6
Pl:0.49w; Po:0.45w.
Lowest position
Starting a cycle wash
1 Draw out the lower and upper basket, load th e dishes and pu sh them back.
the n the upper one (see the section entitled
Loading the Dishwasher ).
2 P our in the detergent (see the secti on e ntitled Salt, Detergent and Rinse Aid ).
3 Insert the plug into the socket. The power su pply is 220-240 VAC /50 HZ, the speci fication
of the socket is 10A 250VAC. M ake sure that the water supp ly is turned on to full pressure.
4 Open the door, pre ss the O N/OFF Button.
5 P ress the prog ram Button , the wash program will be cha nged as follows direction:
Eco Glass 90m in Rapid Sock Auto Inten sive Normal Eco
It is recommen ded to load the lower basket firs t,
“ ”
“ ”
→ → → → → → → → ;
If a p rogram is selected, th e response l ight will . T hen clo se the door, the dishwasher
turn on
wi ll sta rt it s cycle.
Normal
Rapid
Glass
3/22g
3/22 g
3/22 g
For normally soiled loads,
such as pots plates
glasses and lightl y
soiled pans.
、 、
For heaviest s oiled crockery,
and normally soiled pots
pans dishes etc with dried
on soiling.
、
、
A shorter wa sh for lightly
soiled loads a nd quick
wash.
Pre-wash(50 )
Wash ( 60 )
Rinse
Rinse
Rinse(70 )
Dryi ng
℃
℃
℃
Pre-wash(45 )
Wash (55 )
Rinse
Rinse (65 )
Drying
℃
℃
℃
Pre-wash
Wash (45 )
Rinse(65 )
Dryin g
℃
℃
Wash (45 )
Rinse
Rinse (55 )
℃
℃
(50 )℃
180
195
170
30
1.1
0.74
1.4
0.7
15.5
12
8
10
Wash(65 )
Rinse
Rinse (65 )
Drying
℃
℃
90 11.5
1.15
25g
20g
For normally soiled loads
that need quick wash.
To rinse dishes that you plan
to wash later that day.
Pre-wash
15 0.02 3.5
3/22g
For li ghtly soi led cr ockery
and glass.
125 0.75 12
Pre-wash
Wash (40 )
Rinse
Rinse( 60 )
Dr ying
℃
℃
9.5~13
0.9~1.3
150
3/22g
Pre-wash (45 )
Auto was h(45-55 )
Rinse
Rinse(65 )
Drying
℃
℃
℃
Auto sensing wash, lightly,
normall y or heavily soiled
crockery, with or with out
dried-on food
Intensive
90 Min
Soak
EC O
( *EN 50242)
This is standard programme, it i s
suitable to clean normally soiled
tableware and it is the m ost effici ent
programme in terms of its com bined
energy and water consumpt ion for
that type of tableware.
1 piece
1 pie ce
1 piece
1 piece
1 piece
1 piece

Changing the Program Mid-Cycle
If you open the do or , the ma chine will pause. The program light will
stop blinking and the buzzer will mooing every minute unless you close the door . After
you close the door ,the machine will keep on working after 10 seconds.
during a wash cycle
Premise:
A cycle that is underway can only be modified if it has only been r unning for a short time. Otherwise, the
detergent may have already be en released, a nd the appliance may have already drained the wash water.
If this is the case, the detergent dispenser must be refilled (see the section entitled " Loading the
Detergent " ).
Open the door ,press the Program button , the machine will be in standby state,
then you can change the program to the desired cycle setting (see the section entitled " Starting a
wash cycle. . ." ).
more than 3 seconds
1
2
A forgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door
After the spray arms stop working, you can open the door
completely.
2
3
Open the door a little .
14
5The dishwasher will run after 10 seconds.
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwashe r.
Wait for a few minutes bef ore unloading the dishwasher to avoid ha ndlin g the dishes and utensils while they
are still hot and more susceptible to break. They will also dry better.
Switching Off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
Open the door.1. Switch off the dishwasher by pressing the ON/OFF button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
shocks. T he d ishes sh ould coo l down for aroun d 15
Unloading the dishwasher
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
It is normal for the dishwasher to be wet inside.
It is dangerous to open the door mid-cycle,
as hot steam may scald you.
15

The filter prevents larger remnants of food or other objects from getting inside the pump.
The residues may block the filter, in this case t hey must be removed .
The filter system consists of a coar se filter,a flat (Main filter)
And a microfilter(Fine filter).
Food and soil particles trap ped in this filter are pulverized by a
special jet on the l ower spray arm and washed down to d rain.
Larger items, such as p ieces of bones o r glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by the filter, gently squeeze the tap on th e top of this
filter and lift out.
This filter holds soil and food residues in the sump area and
them from being red eposited on the d ishes during wash cycle.
Main filter
1
Coarse filter
2
Fin e filter
3
2
3
1
Filter assembly
The filter efficiently
For best performance and results, the filter must be cleaned re gularly. this r eason, it is a goo d idea to
remove the larger food particles trapped in the filter after each was h cycle by rinsing the semicircular filter and
cup under running water. To remove th e filter device, pull the cup handle in the upward d irect ion.
removes food particles from the wash water, allowing it to be recycle d during the cycle.
For
The d ishwash er must never be used without the filters.
Impro per replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
Step 1 Turn the：filter counterclockwise,
Step 2 lift the filter assy up：
When following this procedure from step1 to step 2, the filter system will be removed;
when following it from Step 2 to Step 1, the filter system will be installed.
16
1
2

The cont rol pane l can be cleaned by using a lightly dampened cloth.
After cleaning, make sure to dry it thoroughly.
For the exterior, use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Winterizing
1 .Cut off the electrical power to the dishwasher at the supply source.
2. Turn off the water supply and disconnect the water inlet pipe from the water valve.
3. Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)
4. Reconnect the water inlet pipe to the water valve.
5. Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.
please take frost protection measures on the dishwasher in winter. Every fter washing cycles,
please operate as follows
time a
：
Cleaning the Filter
Cleaning The Door
To clean the coarse fi lter and the fine f ilter, use a cleaning b rush. R eassemble the filter parts as shown in the figures
on page 16 a nd reinsert positioning and p ressing downwards.
the m in the dish was her, them in t heir sea t
When cle aning the filters, do no t knock t hem. Oth erw ise, the fi lters could be con torted
and the p erforman ce o f the dishwasher c ould be d ecreased.
To cle an the edge around the door, you should only use a soft, ward and damp
cloth.
To avoid penetration of water into the door lock and electrical components, do not
use a spray cleaner of any kind.
Never u se a spray cleaner to clean the door panel as it may dam age the door lock
and electrical components.
Abrasive agents or some paper towels shou ld not be used because of the risk of
scratching or leaving spots on the stainless steel surface.
Cleaning the Spray Arms
If your dishwasher cannot work because of the ice,
please contact professional service persons.
It is necessary to clean the spray arms regularly for hard
water chemicals will clog the sp ray arm jets and bearings.
- A fter each cycle, check for any deb ris i n the filter to avo id fu ture blockage.
- By unscrew ing the coarse fi lter, you can remove the filter system . Re move any food remnants and
clean the filters under running water.
Remarks:
The entire filter assembly should be cleaned once a week.
To remove the lower spray arm, pull out the spray arm u pwa rd.
To remove the up per spray arm, hold the nut, rotate the arm
clockwise to remove it.
Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.
17

It is recommend that you run a wash cy cle with the
dishwasher empty an d the n remove the plug from the
sock et, turn off the water supply and leave the door of
the appliance slightly open. This w ill help the door
seals to last l onger and prevent odours from forming
within the appliance.
If the appliance must be moved, tr y to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
One of the factors that cause odours to form in the
dishwasher n the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
is r ema ining fo od strapped i
Before cleaning or performing maintenance, always
remove the plug from the socket.
To clean the e xterior and rubber p arts of the di shwasher,
do not use solvents or abrasive cle aning products.
Only use a clo th with warm soapy water.
To rem ove spots or stains from the sur face of the
interi or, use a cloth dampened with water a n a little
vinegar, or a cleaning pro duct made specifically for
dishw ashers.
Remove the Plug
No Solvents or Abrasive Cleaning
Moving the Appliance
Seals
After ever y wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odours are not trapped inside.
After Every Wash
When not in use for a longTime
18
The installation of t he pipes
and electrical equipments
should be done by professionals .
Electrical Shock Hazard.Disconnect electrical power
before installing dishwasher.
Failure to do so can result in death or electrical shock.
Installation preparation
Note: please check the accompanying installation accessories(hook for aesthetic panel,screw)
●
The inst allation position of dishwasher should be near the existing inlet and drain ho ses and power cord.
One side of the cabinet si nk should be chosen to facilitate the connection of drain hoses of the dishw asher.