Deep Sea Electronics Plc DSE9460 User manual

TYPICAL WIRING DIAGRAM
DANGER OF DEATH: LIVE PARTS exist within the enclosure. The enclosure cover must
not be removed when connected to an AC supply
Deep Sea Electronics Plc.
Tel:[phone]
Fax: [phone]
Email: [e-mail]
Web: www.deepseaplc.com
Deep Sea Electronics Inc.
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.deepseausa.com
DEEP SEA ELECTRONICS
DSE9460 & DSE9461
INSTALLATION INSTRUCTIONS
053-147
ISSUE 4
INSTALLATION
The battery chargers are wall mounted via four holes on the back of the enclosure. Dimension and
mounting details are given overleaf.
The battery charger is fit-and-forget. It can be permanently connected to the supply and the load, with
no requirement to disable the charger during times of heavy load (such as engine cranking) or when in
parallel with a charging alternator.
BATTERY SUITABILITY
The battery charger is factory set by DSE to suit Lead Acid batteries but can be adjusted to suit other
battery types using the Configuration Suite PC Software.
Care must be taken to ensure the batteries connected to the charger are of the correct ‘technology’ to
suit the setting of the charger.
INDICATIONS
The Battery Charger features an LCD display and depending on the variant, additional voltage and
current meters may be fitted.
BOOST MODE
Boost mode is operated automatically or by activation of the digital input (if configured to perform this
function). This raises the battery charger voltage to the boost voltage setting .
ACCESSING THE FRONT PANEL EDITOR
•The Front Panel Editor (FPE) is accessed by pressing and holding the () button.
•Press the (up) or (down) button to cycle through the Adjustable Parameters listed
overleaf.
•Press the () button to edit a parameter when it is being viewed on the screen. The value
flashes to show edit mode is in progress.
•Press the (+) or (-) button to change the parameter to the required value.
•Press the () button to save the currently selected value. The value ceases flashing to show
editing is complete.
•Press and hold the () button to exit the editor

ADJUSTABLE PARAMETERS
NOTE: On later versions of the DSE2541 display, only parameters 100 to 108 are available
for configuration.
Index
Parameter
Value
100 Contrast 0 %
101 Temperature Units °C, °F
102 Slave ID 1 to 255
103 Baud Rate 4800 to 115200
104 Enable Alarm Popup Screen Enable, Disable
105 Home Page Configuration 0 to 8 (Home Page List)
106 Home Page Timeout 0 s
107 Sleep Mode Timeout 0 s
108 Enable Engineering Page Enable, Disable
Parameter 105 – Home Page Configuration has the following possible selections:
Value
Home Page List
0 Analogue Meters
1 Output Voltage And Current
2 Output Power And Battery Charger Temperature
3 Battery Sensed Voltage And Battery Temperature
4 Mains AC Voltage And Frequency
5 Battery Charger Model And Charger Software Version
7 Control Page
8 Alarms Page
DISPLAY LED INDICATIONS
CHARGER STATUS
FAULT STATUS
BOOST MODE
Condition
LED
State
Condition
LED
State
Condition
LED
State
Charger Off Off No Fault Off Boost Off Off
Charger On On Warning Fault On Boost On On
Shutdown Fault Flashing
DIMENSIONS AND MOUNTING
Measurements in mm
Parameter
Comment
Cabinet
Type Custom cabinet for indoor use only
Overall Size 165 mm X 305 mm X 110 mm
(6.5 ” X 12.0 ” X 4.3 ”)
Material Sheet steel enclosure of all-
round solid construction
Surface
Finish Powder-coated black
Protection
Category IP20, NEMA 1
Weight 2.3 kg (5 lb 1 oz)
Mounting
Type Wall mounted with terminals to bottom.
Mounting
Holes
Diameter 6 mm (0.2 ”)
63 mm X 284 mm
(3.4 ” x 11.2 ”) centres
Operating
Temperature
(With
Deratings)
-30
°
C to +80
°
C
(-22 °F to +176 °F)
REQUIREMENTS FOR UL CERTIFICATION
Parameter
Comment
Screw Terminal
Tightening Torque 4.5 lb-in (0.5 Nm)
Conductors
•
Terminals suitable for connection of conductor size 12 AWG – 26 AWG
(0.5 mm² to 2.0 mm²).
•Conductor protection must be provided in accordance with NFPA 70,
Article 240
•Low voltage circuits (35 V or less) must be supplied from the engine
starting battery or an isolated secondary circuit.
•The communication, sensor, and/or battery derived circuit conductors
shall be separated and secured to maintain at least ¼” (6 mm)
separation from the generator and mains connected circuit conductors
unless all conductors are rated 600 V or greater.
Communication Circuits Must be connected to communication circuits of UL Listed equipment
Mounting
•
Suitable for use in type 1 Enclosure Type rating with surrounding air
temperature -22 ºF to +131 ºF (-30 ºC to +55 ºC)
•Suitable for pollution degree 3 environments when voltage sensing
inputs do not exceed 300 V. When used to monitor voltages over 300 V
device to be installed in an unventilated or filtered ventilation enclosure
to maintain a pollution degree 2 environment.
Operating Temperature -22 ºF to +131 ºF (-30 ºC to +55 ºC)
Storage Temperature -40 ºF to +176 ºF (-40 ºC to +80 ºC)
Charger
Status Boost Mode
Fault
Status