Deka RONDO Series User manual

INSTRUCTION
MANUAL
(Fan pictured is for illustration purposes only.
Styles may vary according to the specific models.)
Ceiling Fan Installation Manual, Rev 1.1
• INSTALLATION
• OPERATION
• MAINTENANCE
• WARRANTY
INFORMATION
Read Instructions carefully
for safe installation and
fan operation
RONDO series
Models: RONDO52XX; RONDO52LEDXX; RONDO58XX; RONDO58LEDXX
CAUTION
DIY MUST BE INSTALLED
BY A LICENSED ELECTRICIAN
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 1

2
1. The appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by a person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the appliance.
3. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local
wiring rules.
4. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems
available. If electrical appliances are disposed of in landfills or dumps, hazardous substances
can leak into the ground water and get into the food chain, damaging your health and well-being.
5. The structure to which the fan is to be mounted must be capable of supporting a weight of 30kg.
6. The fan should be mounted so that the blades are at least 2.1 m above the floor in Australia.
7. This fan is suitable for indoor and covered outdoor areas where the fan is fully undercover.
8. Only a licensed electrician/contractor should perform installation of this product.
9. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the
ceiling fan and refer the warranty information and contact details on page 13 of this document.
10.The replacement of any parts should be performed by our service agent, an appointed qualified
electrician or suitably qualified person.
11.The fixing means for attachment of the ceiling mounting bracket (supplied) shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan.
Thank you for purchasing this quality Deka ceiling fan. To ensure
correct function and safety, please read all instructions before using
the product and keep all instructions for future reference.
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION MUST BE INCORPORATED
INTO THE FIXED WIRING IN ACCORDANCE WITH THE WIRING RULES.
As outlined in clause 7.12.2 of AS/NZS 60335-1 for meeting the minimum electrical safety of this
standard. Please note warranty will be void if installation is without an all-pole disconnection
incorporated in the fixed wiring in accordance with the wiring rules. Example: If a fan is connected
to a circuit that can be isolated via an all-pole safety switch at the switchboard, then this is
considered to be an all-pole disconnection to the ceiling fan electrical circuit, meeting the
requirements of clause 7.12.2 of AS/NZS 60335.1.
SAFETY
PRECAUTIONS
As this DC FAN is supplied with a remote control, a single-pole switch on the active of
the receiver input of remote control must also be included in the wiring, and located in
the same room as the ceiling fan.
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 2

3
Unpack the fan and carefully identify the parts. Please refer to Fig 1.
BEFORE
INSTALLATION
FAN WITH LED LIGHT (Fig 1a.)
1. Mounting bracket x 1
2. Fan assembly with motor, down rod, canopy
and light kit x 1
3. Blades x 4
4. Remote x 1
5. Receiver x 1
6. Balancing kit x 1 set
7. Blade screws x 8 (and one spare)
8. Mounting bracket screws x 2 (timber use only)
FAN WITHOUT LIGHT (Fig 1b.)
1. Mounting bracket x 1
2. Fan assembly with motor, down rod, canopy
and bottom cover x 1
3. Blades x 4
4. Remote x 1
5. Receiver x 1
6. Balancing kit x 1 set
7. Blade screws x 8 (and one spare)
8. Mounting bracket screws x 2 (timber use only)
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 3

4
• The ceiling fan must be installed in a location so that the blades are a minimum 300mm spacing
from the tip of the blade to the nearest objects or walls (including bulkheads and beams).
• Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at
least 30kg, with the two long screws provided (timber use only). Ensure at least 30mm of the screw
is threaded into the support.
Note: The bracket screws provided are for use with wooden
structures only. For structures other than wood, the
appropriate screw type MUST be used.
Angled Ceiling Installation
This fan hanging system supports a maximum 15 degree angled
ceiling installation.
INSTALLING THE
MOUNTING BRACKET
Warning: Ceiling fan must be mounted so that blades are 2.1m from the floor and 300mm from the
wall and other obstructions to the blade tip.
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 4

5
There are two blade installation options, allowing you the choice of either a 3 or 4 bladed ceiling fan.
Before installing the blades, select the one which is most suitable for you.
3 blades: use the 3 blade screw mounting holes following the label instruction guide on the ceiling fan motor.
4 blades: use the 4 blade screw mounting holes following the label instruction guide on the ceiling fan motor.
BLADE
INSTALLATION
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 5

6
Secure the blade on the fan by using 2 blade screws (Fig 2.). For each blade, insert one blade mounting
screw through the blade, and attach lightly to the fan. Insert the second blade mounting screw, and
then securely tighten both mounting screws. Repeat for all blades. Do not use power tools as this
can cause damage to the screws and/or thread in the motor.
Lift the fan assembly onto the mounting bracket. Ensure the registration slot (B) of the hanger ball is
positioned on the stopper (A) of the mounting bracket (C) to prevent the fan from rotating when in
operation.
BLADE
ATTACHMENT
HANGING
THE FAN
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 6

7
WARNING: For your safety all electrical connections must be undertaken by a licensed electrician.
NOTE: An additional all pole disconnection must be incorporated in the fixed wiring in accordance with
the wiring rules.
NOTE: If there are two or more DC ceiling fans installed in the one location, an isolation switch is
required for each ceiling fan. This is required when programming the remote and receiver to
pair correctly together.
NOTE: Wiring diagram includes the light kit wiring. The light wiring diagram and switch is omitted when
no light kit is used with the ceiling fan.
WIRING REQUIREMENT: (Fig 3.)
• Connect the mains power supply to the terminal block (A). Live to “L” terminal. Neutral to “N” terminal.
Earth to “ ” terminal. Ensure the wires are secure and no bare wires are exposed.
• Insert the DC motor receiver into the mounting bracket.
• Insert the 3-port fixed wire quick connector (4a) to the receiver power input socket (4).
• Insert the DC motor receiver output wire connector (3a) to the receiver power output socket (3).
• Join the receiver output wire (1) and the motor power input (1) wire together via the 4-port quick
connectors.
• For Fans with Light Kit:
Insert the LED driver power input wire connector (2a) to the receiver light output socket (2).
For fan models without light, ignore this LED driver power input wire (2a) connection.
ELECTRICAL
WIRING DIAGRAM
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 7

8
• After completing the electrical connection at the mounting bracket terminal block, cover the mounting
bracket with the ceiling canopy. Ensure all electrical wiring is tucked inside the canopy and that the
wires are not damaged during this step. Secure the canopy to the hanger bracket using the screws
provided. Do not overtighten the screws as this will misalign the canopy potentially causing unwanted
noises. For best results, leave screws 4-5mm from mounting bracket and position canopy into the
key lock slot.
BATTERY INSTALLATION
2 x AAA 1.5V batteries are required to operate the remote control.
Loosen the screw from the battery cover.
Pull out the battery cover and install the batteries.
Ensure the polarity is correct as shown in the battery compartment.
Please remove the batteries if you intend not using the ceiling fan for any long periods of time.
OPERATING THE REMOTE
Before you start using the remote, take the time to read through this section and get familiar with the
buttons and function of each button.
NOTE: When you turn on the fan for the first time or switch the main power to the controller on, you
need to start the fan on high speed “6” first and then choose a lower speed. A 5-10 second delay
is common to allow the DC fan to respond to the remote for each change of speed.
NOTE: When you change the fan running direction, a 30-40 second delay is common to allow the DC
fan to slow down and then respond to the remote.
NOTE: The remote and receiver have already been paired during manufacturing. When the ceiling fan
is installed for the first time, pairing of the remote and receiver is NOT required.
FINISHING
THE INSTALLATION
USING YOUR
CEILING FAN
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 8

9
INSTALLING THE REMOTE CONTROL WALL BRACKET
Install the holder with the two screws provided. (Fig 4.)
NATURAL WIND MODE
The fan will run at a changing speed cycle. Highest speed for 20 seconds > Lowest speed for 20
seconds > Highest speed for 20 seconds….
①Fan ON/OFF button
• Press the button to turn the fan on/off.
• Press and hold the button for 5 seconds within
30 seconds of switching the power to the
receiver for pairing the transmitter and receiver.
②Fan speed control button
Press the speed buttons from 6 to 1, the fan will
run from Extra-high speed (6) to Extra-low speed
(1).
③No function
④Turn ON the light button (if with light model)
⑤Turn OFF the light button (if with light model)
⑥Natural wind button
• Press the button to activate the natural wind
mode.
• Press any speed control button to exit the natural
wind mode.
⑦Forward/Reverse button
Press the button to activate the reverse running
function. The fan must be operating to activate
the reverse function. Press again to return to the
forward running function.
⑧Timer control button
Press the button to activate the fan timer
function, the fan will turn off after running 1 hour
/ 4 hours / 8 hours. To cancel the timer function,
just press the fan on/off button.
⑨Batteries (2 x AAA 1.5V) supplied
REMOTE
FUNCTION
1
2
3
4
5
6
7
8
9
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 9

10
FORWARD/REVERSE FUNCTION
Your ceiling fan can operate either in forward mode or reverse mode.
Forward Mode: The fan rotates in an anticlockwise
direction. The airflow will be directed
downwards, for cooling in summer.
Reverse Mode: The fan rotates in a clockwise direction.
The airflow will be directed upwards, for
energy conservation in winter.
You are able to change the output colour of the light kit to either Cool White, Natural White or Warm
White. Utilising the single pole switch in the same room as the fan, simply flick the switch OFF and then
ON (within 2 seconds) and repeat until your desired colour has been selected. Leave the switch on for
normal fan operation via the remote. The remote will “remember” your selection and your desired colour
will be set. Repeat process above to change the colour output if desired.
CHANGING THE COLOUR OF THE LED LIGHT
(For models with light only)
NOTE: The remote and receiver have already been paired during manufacturing. When the
ceiling fan is installed for the first time, pairing of the remote and receiver is NOT required.
Should the remote and receiver lose pairing after installation or during use, the remote and the receiver
must be re-paired. Below are the operating symptoms and method to re-pair the pairing of the DC ceiling
fan remote and receiver.
Issues:
• Loss of control - Fan is only running at high speed after installation
• Loss of control - No reverse function after installation
• Loss of control - Remote cannot communicate with the receiver
Solution:
• Switch off the main power to ceiling fan.
• Press and hold the “ ” button on the remote for 5 seconds (within 30 seconds of switching the
power on to the receiver of the ceiling fan). A long “beep” sound to indicate the paring process is
activated. Release your finger from the power button.
• After waiting 2-3 minutes, turn the fan ON and change the speed of the ceiling fan by the remote to
check the operation and successful paring.
PAIRING OF THE FAN RECEIVER AND REMOTE
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 10

11
WOBBLE:
Note: Ceiling fans tend to move during operation due to the fact that they are mounted on a rubber
grommet. If the fan was mounted rigidly to the ceiling it will cause excessive vibration. Movement of a
few centimetres is quite acceptable and does not suggest any problem.
To Reduce the Fan Wobble: Please check that all screws which fix the mounting bracket and down
rod are secure and blade screws are fastened securely.
NOTE: This fan has been precision balanced at the factory and may need re-balancing. (Balancing kit
supplied can be used if required).
NOISE:
When it is quiet (especially at night) you may hear occasional small noises. Slight power fluctuations
and frequency signals superimposed in the electricity for off-peak hot water control may cause a change
in fan motor noise. This is normal. Please note that this is not a product fault and as such is not covered
under warranty – All electric motors are audible to some extent. Please allow a 24-hour
“breaking-in” period, most noises associated with a new fan disappear during this time.
CARE AND CLEANING:
• Every 6 months periodic cleaning of your ceiling fan is the only maintenance required. Use a soft
brush or lint free cloth to avoid scratching the paint finish. Please turn off electricity power when you
do so.
• Do not soak or immerse your ceiling fan in the water or other liquids. It could damage the motor or
the blades and create the possibility of an electrical shock.
• Ensure that the fan does not come in contact with any organic solvents or cleaners.
• To clean the fan blade, wipe with only a damp clean cloth with NO organic solvents or cleaners.
• The motor has a permanently lubricated ball bearing so there is no need to oil.
NOTE: Always turn OFF the power at the mains switch before performing any maintenance or
attempting to clean your fan.
AFTER
INSTALLATION
TECHNICAL
INFORMATION
CEILING RATED RATED POWER RATED POWER NW
FAN MODEL VOLTAGE (MOTOR) (LAMP)
RONDO52XX 220-240V AC 50Hz 38W N/A 5.4kg
RONDO52LEDXX 220-240V AC 50Hz 38W 20W 5.7kg
RONDO58XX 220-240V AC 50Hz 38W N/A 5.8kg
RONDO58LEDXX 220-240V AC 50Hz 38W 20W 6.1kg
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 11

12
All electric motors, including fan motors make some noise and may feel hot if touched – this is NOT A
FAULT. Ceiling fans tend to move during operation as they are not generally rigid-mounted. Rigid
mounted ceiling fans generate excessive vibration (which leads to noise) and stress on their mountings.
Movement in a ceiling fan is not uncommon and does not suggest the fan will fall down.
Some fans wobble more than others, even in the same model.
Fan Operation
A ceiling fan rotates much more slowly than an electric desk fan; it cools people effectively by introducing
slow movement into the otherwise still, hot air of a room, inducing natural evaporative cooling. Fans
never actually cool air, unlike air-conditioning equipment, but use significantly less power.
Normal Wear and Tear
Threaded components working slightly loose, or blade carriers becoming slightly bent due to vigorous
cleaning or bumping can cause extra wobble and noise. This is not covered under warranty, but a little
care and maintenance can reduce or prevent this problem.
Night Noises
This is the biggest cause of service calls, which are outside the manufacturer’s warranty. If a fan has a
fault, then it would be noticeable at ALL TIMES. Obviously when everything is quiet at night you will be
more inclined to hear small noises, which may not be noticeable at other times. Even slight signals
super imposed in your electricity supply for off peak hot water control may cause a change in the fan
motor noise, which is deemed normal. Solar power systems will cause extra humming in motors. In
both scenarios it is recommended that you explore options of adding a filter that can be installed to
eliminate these issues.
Dimming
The light kit supplied with this fan is NOT DIMMABLE.
Dimmers and solid state wall controllers can NOT BE USED for the operation of the fan motor.
This will instantly void any warranty provided.
IMPORTANT
FACTS
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 12

13
Important ceiling fan warranty information for owners and installers.
Our goods come with guarantees that cannot be excluded under Australian Consumer Law. You are entitled to a replacement
or refund for a major fault and compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
This product is covered for six (6) years in total consisting of a two (2) year in-home warranty followed by a four (4) year
parts only warranty. Please note that remote controls (if applicable) and other accessories are covered for one (1) year from
the date of purchase.
What is an in-home warranty?
Deka branded ceiling fans offers a two (2) year in-home parts and labour warranty on ceiling fans installed within the coverage
of our network of service agents and in cases where the product fails due to defective materials or workmanship.
This warranty does not cover installation faults, house wiring faults, loose blades or damage of any kind. In areas outside
of the coverage of Deka service agents, Deka will reimburse a standard fee of $88.00 (inc. GST) for consumers using their
own electricians. Conditions apply and Deka support must be contacted PRIOR to organising your own electrician. Under
no circumstances will reimbursements be paid without prior consent of Deka support.
Subject to your “Rights under Australian consumer law”, but otherwise to the maximum extent permitted by law, the Deka
warranty will NOT cover the below:
1. Where installation was not carried out by a licensed electrician or contractor.
2. Products not installed as per the instruction manual and in accordance to SAA and local authority regulations.
3. Defect, damage or failure resulting from misuse, accident, neglect, abuse, tampering, modifications or unauthorized
repairs of any kind by any person.
4. Minor variations of speed may be evident even between same model of fans. No two fans run exactly the same, even
across all speeds.
5. Fan “wobbles” – Any wobble is usually caused by the mounting to the ceiling not being adequate or mismatched or out
of alignment blades. Blades should not be mixed from one fan to another as the blades sets are balanced during
production. Refer to the User Manual for more information.
6. Defect, damage or failure resulting from any acts of God, including damages from lightning.
7. Defect, damage or failure resulting from power grid fluctuations or power surges.
8. Damage caused by alternate power supplies, e.g. Solar inverters etc.
9. Disposable accessories, e.g. Batteries or light globes (unless otherwise stated)
10. “Night noises” - intermittent humming or other influences from mains power delivery infrastructure – Refer Important
Facts for further information.
11. Water damage
12. The cost of renting, obtaining and using special equipment (i.e. scaffolding, scissor lifts etc.) for accessing products
installed at a height of greater than 3.5 meters.
13. Liability for consequential loss or claims for damage to furniture, carpets, walls, ceilings, foundations or and other event
either directly or indirectly resulting from a faulty product or accessory to the maximum extent permitted by law.
After reading the above information:
1. Should you consider there is a fault relating to the installation, please contact the original installer to rectify.
2. Should you consider that there is a manufacturer's defect with the fan, please go to www.dekafans.com.au and click on
Warranty. Fully complete and supply all requested information for an expedited warranty process.
WARRANTY
INFORMATION
Warranty is provided by Repelec (Aust)
16 Rayben Street Glendenning NSW 2761
Phone: [phone] Email: [email protected]
Website: www.repelec.com.au
This warranty is valid
in Australia only
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 13

www.dekafans.com.au
RONDO fan instructions_Sept20.qxp_Layout 1 14/9/20 11:39 am Page 14