Dell Inspiron 1320 User manual

Dell™Inspiron™1320ServiceManual
Notes, Cautions, and Warnings
Information in this document is subject to change without notice.
©2009DellInc.Allrightsreserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under
license; Microsoft, Windows,Windows Vista, and Windows Vista start button logo are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or
other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Model P04S Type: P04S001
June 2009 Rev. A00
Before You Begin
Battery
Module Cover
Memory Module(s)
Wireless Mini-Card
Coin-Cell Battery
Center Control Cover
Keyboard
Hard Drive
Palm Rest
Internal Card With Bluetooth Wireless Technology
Speakers
Processor Fan
System Board
Processor Heat Sink Assembly
Processor
I/O Board
Battery Latch Assembly
Display
Camera Board
Flashing the BIOS
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Back to Contents Page
Battery Latch Assembly
Dell™Inspiron™1320ServiceManual
Removing the Battery Latch Assembly
Replacing the Battery Latch Assembly



Removing the Battery Latch Assembly

1. Follow the instructions in Before You Begin.

2. Remove the system board (see Removing the System Board).

3. Press and push the battery release latch clip to release it from the battery latch assembly.

4. Remove the spring from the hook that holds it in place.

5. Lift the battery latch assembly out of the computer base.
Replacing the Battery Latch Assembly

1. Place the battery latch assembly in the channel in the computer base.

2. Push the battery release latch clip into the battery latch assembly.

3. Using a small screwdriver, place the spring over the hook on the computer base.
Ensure that the newly installed latch moves smoothly and freely when pushed and released.

4. Replace the system board (see Replacing the System Board).
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
battery latch assembly
2
battery release latch clip
3
spring

Back to Contents Page


Back to Contents Page
Battery
Dell™Inspiron™1320ServiceManual
Removing the Battery
Replacing the Battery



Removing the Battery

1. Follow the procedures in Before You Begin.

2. Turn the computer over.

3. Slide the battery release latch to the unlock position.

4. Slide the battery out and lift it out of the battery bay.
Replacing the Battery


1. Align the triangles marked on the battery and the computer base.

2. Slide the battery into the battery bay until it clicks into place.
Back to Contents Page

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for
other Dell computers.
1
battery
2
battery release latch
CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer.

Back to Contents Page
Before You Begin
Dell™Inspiron™1320ServiceManual
Recommended Tools
Turning Off Your Computer
Before Working Inside Your Computer
This section provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the
following conditions exist:
lYou have performed the steps in Turning Off Your Computer and Before Working Inside Your Computer.
lYou have read the safety information that shipped with your computer.
lA component can be replaced or—if purchased separately—installed by performing the removal procedure in reverse order.
Recommended Tools
The procedures in this document may require the following tools:
lSmall flat screwdriver
lPhillips screwdriver
lPlastic scribe
lHex nut driver
lBIOS upgrade CD or the BIOS executable update program available on the Dell Support website at support.dell.com
Turning Off Your Computer


1. Save and close all open files and exit all open programs.

2. In Microsoft®Windows Vista®, click Start , click the arrow , and then click Shut Down.
The computer turns off after the operating system shutdown process finishes.

3. Ensure that the computer and any attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut
down your operating system, press and hold the power button for at least 8 to 10 seconds until the computer turns off.
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your own personal safety.






CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal
mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking
tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep
them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented
and aligned.
CAUTION: To avoid damaging the computer, perform the following steps before you begin working inside the computer.

1. Ensure that the work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning Off Your Computer).

3. If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions.


4. Disconnect all telephone or network cables from the computer.

5. Press and eject any installed cards from the ExpressCard slot or the 5-in-1 Media Card Reader.

6. Disconnect your computer and all attached devices from their electrical outlets.


7. Remove the battery (see Removing the Battery).

8. Turn the computer top-side up, open the display, and press the power button to ground the system board.
Back to Contents Page

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.

Back to Contents Page
Flashing the BIOS
Dell™Inspiron™1320ServiceManual
Flashing the BIOS From a CD
Flashing the BIOS From the Hard Drive
If a BIOS-update program CD is provided with the new system board, flash the BIOS from the CD. If you do not have a BIOS-update program CD, flash the
BIOS from the hard drive.
Flashing the BIOS From a CD

1. Ensure that the AC adapter is plugged in and that the main battery is installed properly.

2. Insert the BIOS-update program CD, and restart the computer.
Follow the procedures that appear on the screen. The computer continues to boot and updates the new BIOS. When the flash update is complete, the
computer will automatically restart.

3. Press <F2> during POST to enter the system setup program.

4. Press <F9> to reset the computer defaults.

5. Press <Esc>, select Save changes and reboot, and press <Enter> to save configuration changes.

6. Remove the BIOS-update program CD from the drive and restart the computer.
Flashing the BIOS From the Hard Drive

1. Ensure that the AC adapter is plugged in, the main battery is properly installed, and a network cable is attached.

2. Turn on the computer.

3. Locate the latest BIOS update file for your computer at support.dell.com.

4. Click Drivers & Downloads®Select Model.

5. Select the type of product in the Select Your Product Family list.

6. Select the product brand in the Select Your Product Line list.

7. Select the product model number in the Select Your Product Model list.

8. Click Confirm.

9. A list of results appear on the screen. Click BIOS.

10. Click Download Now to download the latest BIOS file.
The File Download window appears.

11. Click Save to save the file on your desktop. The file downloads to your desktop.

12. Click Close if the Download Complete window appears.
The file icon appears on your desktop and is titled the same as the downloaded BIOS update file.

13. Double-click the file icon on the desktop and follow the procedures on the screen.
Back to Contents Page
NOTE: If you use a BIOS-update program CD to flash the BIOS, set up the computer to boot from a CD before inserting the CD.
NOTE: If you have selected a different model and want to start over again, click Start Over on the top right of the menu.



Back to Contents Page
Internal Card With Bluetooth Wireless Technology
Dell™Inspiron™1320ServiceManual
Removing the Bluetooth Card
Replacing the Bluetooth Card



Removing the Bluetooth Card

1. Follow the procedures in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Remove the center control cover (see Removing the Center Control Cover).

4. Remove the keyboard (see Removing the Keyboard).

5. Remove the hard drive (see Removing the Hard Drive).

6. Remove the palm rest (see Removing the Palm Rest).

7. Remove the screw that secures the Bluetooth card to the system board.

8. Lift the Bluetooth card to disconnect it from the system board connector.
Replacing the Bluetooth Card

1. Follow the procedures in Before You Begin.

2. Align the connector on the Bluetooth card with the connector on the system board and press gently.

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
screw
2
Bluetooth®card

3. Replace the screw that secures the Bluetooth card to the system board.

4. Replace the palm rest (see Replacing the Palm Rest).

5. Replace the hard drive (see Replacing the Hard Drive).

6. Replace the keyboard (see Removing the Keyboard).

7. Replace the center control cover (see Replacing the Center Control Cover).

8. Replace the battery (see Replacing the Battery).
Back to Contents Page


Back to Contents Page
Camera Board
Dell™Inspiron™1320ServiceManual
Removing the Camera Board
Replacing the Camera Board



Removing the Camera Board

1. Follow the instructions in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Remove the center control cover (see Removing the Center Control Cover).

4. Remove the keyboard (see Removing the Keyboard).

5. Remove the hard drive (see Removing the Hard Drive).

6. Remove the palm rest (see Removing the Palm Rest).

7. Remove the display assembly (see Removing the Display Assembly).

8. Remove the display bezel (see Removing the Display Bezel).

9. Disconnect the camera cable from the connector on the camera board.

10. Remove the screw that secures the camera board to the display cover.

11. Remove the camera board off the display cover.
Replacing the Camera Board

1. Align the camera board over the screw hole.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
camera board
2
screw
3
camera cable connector


2. Replace the screw that secure the camera board to the display cover.

3. Connect the camera cable to the connector on the camera board.

4. Replace the display bezel (see Replacing the Display Bezel).

5. Replace the display assembly (see Replacing the Display Assembly).

6. Replace the palm rest (see Replacing the Palm Rest).

7. Replace the hard drive (see Replacing the Hard Drive).

8. Replace the keyboard (see Replacing the Keyboard).

9. Replace the center control cover (see Replacing the Center Control Cover).

10. Replace the battery (see Replacing the Battery).
Back to Contents Page


Back to Contents Page
Coin-Cell Battery
Dell™Inspiron™1320ServiceManual
Removing the Coin-Cell Battery
Replacing the Coin-Cell Battery



Removing the Coin-Cell Battery

1. Follow the procedures in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Remove the module cover (see Removing the Module Cover).

4. Use a plastic scribe and gently pry the coin-cell battery.
Replacing the Coin-Cell Battery

1. Place the coin-cell battery with the positive (+) side facing upwards.

2. Slide the coin-cell battery into the slot and gently press until it snaps into place.

3. Replace the module cover (see Replacing the Module Cover).

4. Replace the battery (see Replacing the Battery).
Back to Contents Page

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
coin-cell battery
2
plastic scribe

Back to Contents Page
Processor
Dell™Inspiron™1320ServiceManual
Removing the Processor
Replacing the Processor





Removing the Processor

1. Follow the instructions in Before You Begin.

2. Remove the processor heat sink assembly (see Removing the Processor Heat Sink Assembly).



3. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop.



WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
CAUTION: To prevent intermittent contact between the ZIF-socket cam screw and the processor when removing or replacing the processor, press
to apply slight pressure to the center of the processor while turning the cam screw.
CAUTION: To avoid damage to the processor, hold the screwdriver such that it is perpendicular to the processor when turning the cam screw.
CAUTION: When removing the processor, pull it straight up. Be careful not to bend the pins on the processor.
CAUTION: To prevent intermittent contact between the ZIF-socket cam screw and the processor when removing or replacing the processor, press
to apply slight pressure to the center of the processor while turning the cam screw.
1
processor
2
ZIF socket
3
ZIF-socket cam screw
CAUTION: To ensure maximum cooling for the processor, do not touch the heat transfer areas on the processor thermal-cooling assembly. The
oils in your skin can reduce the heat transfer capability of the thermal pads.
CAUTION: When removing the processor module, pull the module straight up. Be careful not to bend the pins on the processor module.


4. Lift the processor module from the ZIF socket.
Replacing the Processor

1. Follow the procedures in Before You Begin.

2. Align the pin-1 corner of the processor module with the pin-1 corner of the ZIF socket, then insert the processor module.
When the processor module is properly seated, all four corners are aligned at the same height. If one or more corners of the module are higher than the
others, the module is not seated properly.


3. Tighten the ZIF socket by turning the cam screw clockwise to secure the processor module to the system board.

4. Replace the processor heat sink assembly (see Replacing the Processor Heat Sink Assembly).

Back to Contents Page

NOTE: If a new processor is installed, you will receive a new thermal-cooling assembly, which will include an affixed thermal pad, or you will receive a
new thermal pad along with documentation to illustrate proper installation.
NOTE: The pin-1 corner of the processor module has a triangle that aligns with the triangle on the pin-1 corner of the ZIF socket.
CAUTION: To avoid damage to the processor, hold the screwdriver perpendicular to the processor when turning the cam screw.
CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.

Back to Contents Page
Processor Heat Sink Assembly
Dell™Inspiron™1320ServiceManual
Removing the Processor Heat Sink Assembly
Replacing the Processor Heat Sink Assembly



Removing the Processor Heat Sink Assembly

1. Follow the instructions in Before You Begin.

2. Follow the procedures from step 2 to step 18 in Removing the System Board.

3. In sequential order (indicated on the processor heat sink), loosen the four captive screws that secure the processor heat sink assembly to the system
board.

4. Lift the processor heat sink assembly off the system board.
Replacing the Processor Heat Sink Assembly

1. Place the processor heat sink assembly on the system board.

2. Align the four captive screws on the processor heat sink assembly with the screw holes on the system board and tighten the screws in ascending order.

3. Follow the procedures from step 3 to step 17 in Replacing the System Board.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
WARNING: If you remove the processor heat sink assembly from the computer when the heat sink is hot, do not touch the metal housing of the
heat sink.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
processor heat sink assembly
2
captive screws (4)
NOTE: This procedure assumes that you have already removed the processor heat sink assembly and are ready to replace it.
NOTE: The original thermal pad can be reused if the original processor and heat sink are reinstalled together. If either the processor or heat sink is
replaced, use the thermal pad provided in the kit to ensure that thermal conductivity is achieved.
NOTE: This procedure assumes that you have already removed the processor heat sink assembly and are ready to replace it.

Back to Contents Page


Back to Contents Page
Display
Dell™Inspiron™1320ServiceManual
Display Assembly
Hinge Caps
Display Bezel
Display Panel
Display Panel Bracket



Display Assembly

Removing the Display Assembly

1. Follow the instructions in Before You Begin.

2. Remove the battery (see Removing the Battery).

3. Remove the module cover (see Removing the Module Cover).

4. Disconnect the antenna cables from the Mini-Card.

5. Remove the center control cover (see Removing the Center Control Cover).

6. Remove the keyboard (see Removing the Keyboard).

7. Remove the hard drive (see Removing the Hard Drive).

8. Remove the palm rest (see Removing the Palm Rest).

9. Disconnect the display cable and the camera cable from their respective system board connectors.

10. Remove the six screws (three on each side) that secure the display assembly to the computer base.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.


11. Make note of the cable routing and carefully dislodge the Mini-Card antenna cables from the routing guides.

12. Lift the display assembly off the computer.

Replacing the Display Assembly

1. Place the display assembly in position and replace the six screws (three on each side) of the display assembly.

2. Route the Mini-Card antenna cables through the routing guides.

3. Connect the display cable and the camera cable to their respective system board connectors.

4. Replace the palm rest (see Replacing the Palm Rest).

5. Replace the hard drive (see Replacing the Hard Drive).

6. Replace the keyboard (see Replacing the Keyboard).

7. Replace the center control cover (see Replacing the Center Control Cover).

8. Connect the antenna cables to the Mini-Card.

9. Replace the module cover (see Replacing the Module Cover).

10. Replace the battery (see Replacing the Battery).

Hinge Caps

Removing the Hinge Caps

1. Follow the instructions in Before You Begin.

1
screws (6)
2
display cable connector
3
camera cable connector
CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.


2. Remove the battery (see Removing the Battery).

3. Remove the center control cover (see Removing the Center Control Cover).

4. Remove the keyboard (see Removing the Keyboard).

5. Remove the hard drive (see Removing the Hard Drive).

6. Remove the palm rest (see Removing the Palm Rest).

7. Remove the display assembly (see Removing the Display Assembly).

8. Press the hinge caps and pull them out.

Replacing the Hinge Caps

1. Place the hinge caps in the location and push them in.

2. Replace the display assembly (see Replacing the Display Assembly).

3. Replace the palm rest (see Replacing the Palm Rest).

4. Replace the hard drive (see Replacing the Hard Drive).

5. Replace the keyboard (see Replacing the Keyboard).

6. Replace the center control cover (see Replacing the Center Control Cover).

7. Replace the battery (see Replacing the Battery).

8. Replace any cards to the ExpressCard slot.
Display Bezel

Removing the Display Bezel


1. Remove the display assembly (see Removing the Display Assembly).
1
hinge caps (2)
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: The display bezel is extremely fragile. Be careful when removing it to prevent damaging the bezel.