Dell Inspiron 14 Intel User manual
Dell™Inspiron™N4020/N4030ServiceManual
Notes, Cautions, and Warnings
Information in this document is subject to change without notice.
©2010DellInc.Allrightsreserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and Inspiron are trademarks of Dell Inc.; Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell
under license; Microsoft,Windows, Windows Vista, and the Windows Vista start button logo are either trademarks or registered trademarks of Microsoft Corporation in the United
States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
RegulatorymodelP07GseriesRegulatorytypeP07G001;P07G003
March2010Rev.A00
Before You Begin
Battery
Hard Drive
Optical Drive
Module Cover
Memory Module(s)
Keyboard
Wireless Mini-Card
Palm Rest
Power Button Board
Display
Camera
Internal Card With Bluetooth®Wireless Technology
System Board
Coin-Cell Battery
Thermal Cooling Assembly
Processor Module
I/O Board
Speakers
Battery Latch Assembly
Flashing the BIOS
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Back to Contents Page
Module Cover
Dell™Inspiron™N4020/N4030ServiceManual
Removing the Module Cover
Replacing the Module Cover
Removing the Module Cover
1. Follow the instructions in Before You Begin.
2. Remove the battery (see Removing the Battery).
3. Remove the screw that secures the module cover to the computer base.
4. Using the notch on the computer base, lift and slide the module cover tabs out of the slots on the computer base.
Replacing the Module Cover
1. Follow the instructions in Before You Begin.
2. Slide the three tabs on the module cover into the slots on the computer base and gently snap the module cover into place.
3. Replace the screw that secures the module cover to the computer base.
4. Replace the battery (see Replacing the Battery).
Back to Contents Page
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
screw
2
module cover
3
tabs (3)
CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.
Back to Contents Page
Battery Latch Assembly
Dell™Inspiron™N4020/N4030ServiceManual
Removing the Battery Latch Assembly
Replacing the Battery Latch Assembly
Removing the Battery Latch Assembly
1. Follow the instructions in Before You Begin.
2. Follow the instructions from step 2 to step 13 in Removing the System Board.
3. Remove the I/O board (see Removing the I/O Board).
4. Press and push the plastic clips on battery release latch to release it from the battery latch assembly.
5. Using a small screwdriver, remove the latch spring on the battery latch assembly.
6. Slide the battery latch assembly to the side and remove it from the computer base.
Replacing the Battery Latch Assembly
1. Follow the instructions in Before You Begin.
2. Slide the battery latch assembly into place.
3. Using a small screwdriver, place the latch spring over the hook on the battery latch assembly.
4. Push the plastic clips on the battery release latch into the hole on the battery latch assembly to secure the battery release latch.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on the back of the computer).
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
battery latch assembly
2
plastic clips
3
latch spring
5. Replace the I/O board (see Replacing the I/O Board).
6. Follow the instructions from step 6 to step 18 in Replacing the System Board.
Back to Contents Page
CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.
Back to Contents Page
Before You Begin
Dell™Inspiron™N4020/N4030ServiceManual
Recommended Tools
Turning Off Your Computer
Before Working Inside Your Computer
This manual provides procedures for removing and installing components in your computer. Unless otherwise noted, each procedure assumes that the
following conditions exist:
lYou have performed the steps in Turning Off Your Computer and Before Working Inside Your Computer.
lYou have read the safety information that shipped with your computer.
lA component can be replaced or—if purchased separately—installed by performing the removal procedure in the reverse order.
Recommended Tools
The procedures in this document may require the following tools:
lSmall flat-blade screwdriver
lPhillips screwdriver
lPlastic scribe
lBIOS executable update program available at support.dell.com
Turning Off Your Computer
1. Save and close all open files and exit all open programs.
2. Shut down the operating system:
Windows®Vista:
Click the Start button , click the arrow , and then click Shut Down.
Windows®7:
Click the Start button and then click Shut Down.
3. Ensure that the computer is turned off. If your computer did not automatically turn off when you shut down the operating system, press and hold the
power button until the computer turns off.
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your own personal safety.
CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal
mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking
tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep
them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented
and aligned.
1. Ensure that the work surface is flat and clean to prevent the computer cover from being scratched.
2. Turn off your computer (see Turning Off Your Computer) and all attached devices.
3. Disconnect all telephone or network cables from the computer.
4. Press and eject any installed cards from the 5-in-1 media card reader.
5. Disconnect your computer and all attached devices from their electrical outlets.
6. Disconnect all attached devices from your computer.
7. Remove the battery (see Removing the Battery).
8. Turn the computer top-side up, open the display, and press the power button to ground the system board.
Back to Contents Page
CAUTION: To avoid damaging the computer, perform the following steps before you begin working inside the computer.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
Back to Contents Page
Flashing the BIOS
Dell™Inspiron™N4020/N4030ServiceManual
1. Turn on the computer.
2. Go to support.dell.com/support/downloads.
3. Click Select Model.
4. Locate the BIOS update file for your computer:
If you have your computer's Service Tag:
a. Click Enter a Service Tag.
b. Enter your computer's Service Tag in the Enter a service tag: field, click Go, and proceed to step 5.
If you do not have your computer's Service Tag:
a. Select the type of product in the Select Your Product Family list.
b. Select the product brand in the Select Your Product Line list.
c. Select the product model number in the Select Your Product Model list.
d. Click Confirm.
5. A list of results appear on the screen. Click BIOS.
6. Click Download Now to download the latest BIOS file.
The File Download window appears.
7. Click Save to save the file on your desktop. The file downloads to your desktop.
8. Click Close if the Download Complete window appears.
The file icon appears on your desktop and is titled the same as the downloaded BIOS update file.
9. Double-click the file icon on the desktop and follow the instructions on the screen.
Back to Contents Page
NOTE: The Service Tag for your computer is located at the bottom of the computer.
NOTE: If you have selected a different model and want to start over again, click Start Over on the top right of the menu.
Back to Contents Page
Internal Card With Bluetooth®Wireless Technology
Dell™Inspiron™N4020/N4030ServiceManual
Removing the Bluetooth Card
Replacing the Bluetooth Card
If you ordered a card with Bluetooth wireless technology with your computer, it is already installed.
Removing the Bluetooth Card
1. Follow the instructions in Before You Begin.
2. Remove the battery (see Removing the Battery).
3. Follow the instructions from step 3 to step 4 in Removing the Hard Drive.
4. Follow the instructions from step 3 to step 5 in Removing the Optical Drive.
5. Remove the module cover (see Removing the Module Cover).
6. Remove the memory module(s) (see Removing the Memory Module(s)).
7. Remove the keyboard (see Removing the Keyboard).
8. Remove the palm rest (see Removing the Palm Rest).
9. Lift the Bluetooth card to disconnect it from the connector on the system board.
Replacing the Bluetooth Card
1. Follow the instructions in Before You Begin.
2. Align the connector on the Bluetooth card with the connector on the system board and press the Bluetooth card until it is fully seated.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
Bluetooth card
3. Replace the palm rest (see Replacing the Palm Rest).
4. Replace the keyboard (see Replacing the Keyboard).
5. Replace the memory module(s) (see Replacing the Memory Module(s)).
6. Replace the module cover (see Replacing the Module Cover).
7. Follow the instructions from step 3 to step 4 in Replacing the Optical Drive.
8. Follow the instructions from step 4 to step 5 in Replacing the Hard Drive.
9. Replace the battery (see Replacing the Battery).
Back to Contents Page
CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.
Back to Contents Page
Camera
Dell™Inspiron™N4020/N4030ServiceManual
Removing the Camera
Replacing the Camera
Removing the Camera
1. Follow the instructions in Before You Begin.
2. Remove the battery (see Removing the Battery).
3. Follow the instructions from step 3 to step 4 in Removing the Hard Drive.
4. Follow the instructions from step 3 to step 5 in Removing the Optical Drive.
5. Remove the module cover (see Removing the Module Cover).
6. Remove the memory module(s) (see Removing the Memory Module(s)).
7. Remove the keyboard (see Removing the Keyboard).
8. Remove the palm rest (see Removing the Palm Rest).
9. Remove the display assembly (see Removing the Display Assembly).
10. Remove the display bezel (see Removing the Display Bezel).
11. Disconnect the camera cable from the connector on the camera module.
12. Slide and lift the camera module to remove it from the tabs on the display cover.
13. Lift the camera module out of the display cover.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
camera module
2
tabs (2)
3
display cover
4
camera cable connector
Replacing the Camera
1. Follow the instructions in Before You Begin.
2. Secure the camera module using the tabs on the display cover.
3. Connect the camera cable to the connector on the camera module.
4. Replace the display bezel (see Replacing the Display Bezel).
5. Replace the display assembly (see Replacing the Display Assembly).
6. Replace the palm rest (see Replacing the Palm Rest).
7. Replace the keyboard (see Replacing the Keyboard).
8. Replace the memory module(s) (see Replacing the Memory Module(s)).
9. Replace the module cover (see Replacing the Module Cover).
10. Follow the instructions from step 3 to step 4 in Replacing the Optical Drive.
11. Follow the instructions from step 4 to step 5 in Replacing the Hard Drive.
12. Replace the battery (see Replacing the Battery).
Back to Contents Page
CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.
Back to Contents Page
Coin-Cell Battery
Dell™Inspiron™N4020/N4030ServiceManual
Removing the Coin-Cell Battery
Replacing the Coin-Cell Battery
Removing the Coin-Cell Battery
1. Follow the instructions in Before You Begin.
2. Follow the instructions from step 2 to step 14 in Removing the System Board.
3. Use a plastic scribe to pry up the coin-cell battery from the slot on the system board.
Replacing the Coin-Cell Battery
1. Follow the instructions in Before You Begin.
2. Hold the coin-cell battery with the positive side up.
3. Slide the coin-cell battery into the slot and gently press until it snaps in place.
4. Follow the instructions from step 5 to step 18 in Replacing the System Board.
Back to Contents Page
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
plastic scribe
2
coin-cell battery
CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.
Back to Contents Page
Processor Module
Dell™Inspiron™N4020/N4030ServiceManual
Removing the Processor Module
Replacing the Processor Module
Removing the Processor Module
1. Follow the instructions in Before You Begin.
2. Remove the thermal cooling assembly (see Removing the Thermal Cooling Assembly).
3. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop.
4. Lift the processor module from the ZIF socket.
Replacing the Processor Module
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: To prevent intermittent contact between the ZIF-socket cam screw and the processor module when removing or replacing the
processor, press to apply slight pressure to the center of the processor module while turning the cam screw.
CAUTION: To avoid damage to the processor module, hold the screwdriver so that it is perpendicular to the processor module when turning the
cam screw.
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
ZIF socket
2
ZIF-socket cam screw
CAUTION: To ensure maximum cooling for the processor module, do not touch the heat transfer areas on the processor thermal-cooling assembly.
The oils in your skin can reduce the heat transfer capability of the thermal pads.
CAUTION: When removing the processor module, lift the module straight up. Be careful not to bend the pins on the processor module.
1. Follow the instructions in Before You Begin.
2. Align the pin-1 corner of the processor module with the pin-1 corner of the ZIF socket, then place the processor module.
When the processor module is properly seated, all four corners are aligned at the same height. If one or more corners of the module are higher than the
others, the module is not seated properly.
3. Tighten the ZIF socket by turning the cam screw clockwise to secure the processor module to the system board.
4. Replace the thermal cooling assembly (see Replacing the Thermal Cooling Assembly).
Back to Contents Page
NOTE: If a new processor module is installed, you will receive a new thermal-cooling assembly, which will include an affixed thermal pad, or you will
receive a new thermal pad along with documentation to illustrate proper installation.
NOTE: The pin-1 corner of the processor module has a triangle that aligns with the triangle on the pin-1 corner of the ZIF socket.
CAUTION: To avoid damage to the processor module, hold the screwdriver perpendicular to the processor module when turning the cam screw.
Back to Contents Page
Thermal Cooling Assembly
Dell™Inspiron™N4020/N4030ServiceManual
Removing the Thermal Cooling Assembly
Replacing the Thermal Cooling Assembly
Removing the Thermal Cooling Assembly
1. Follow the instructions in Before You Begin.
2. Follow the instructions from step 2 to step 14 in Removing the System Board.
3. Disconnect the fan cable from the connector on the system board.
4. In sequential order (indicated on the thermal cooling assembly), loosen the four captive screws that secure the assembly to the system board.
5. Lift the thermal cooling assembly off the system board.
Replacing the Thermal Cooling Assembly
1. Follow the instructions in Before You Begin.
2. Place the thermal cooling assembly on the system board.
3. Align the four captive screws on the thermal cooling assembly with the screw holes on the system board and tighten the screws in sequential order
(indicated on the thermal cooling assembly).
4. Connect the fan cable to the connector on the system board.
5. Follow the instructions from step 5 to step 18 in Replacing the System Board.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
WARNING: If you remove the thermal cooling assembly from the computer when the heat sink is hot, do not touch the metal housing of the
thermal cooling assembly.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
1
thermal cooling assembly
2
fan cable connector
3
captive screws (4)
NOTE: This procedure assumes that you have already removed the thermal cooling assembly and are ready to replace it.
CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.
Back to Contents Page
Back to Contents Page
Display
Dell™Inspiron™N4020/N4030ServiceManual
Display Assembly
Display Bezel
Display Panel
Display Assembly
Removing the Display Assembly
1. Follow the instructions in Before You Begin.
2. Remove the battery (see Removing the Battery).
3. Follow the instructions from step 3 to step 4 in Removing the Hard Drive.
4. Follow the instructions from step 3 to step 5 in Removing the Optical Drive.
5. Remove the module cover (see Removing the Module Cover).
6. Remove the memory module(s) (see Removing the Memory Module(s)).
7. Remove the keyboard (see Removing the Keyboard).
8. Remove the palm rest (see Removing the Palm Rest).
9. Disconnect the antenna cables from the Mini-Card (see Removing the Mini-Card) and remove the antenna cables from the routing guides.
10. Disconnect the display cable from the connector on the system board.
11. Remove the two screws (one on each side) that secure the display assembly to the computer base.
12. Lift and remove the display assembly out of the computer base.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™
is not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the
computer.
Replacing the Display Assembly
1. Follow the instructions in Before You Begin.
2. Place the display assembly in position and replace the two screws (one on each side) that secure the display assembly to the computer base.
3. Connect the display cable to the connector on the system board.
4. Route the antenna cables through the routing guides and connect the cables to the Mini-Card (see Replacing the Mini-Card).
5. Replace the palm rest (see Replacing the Palm Rest).
6. Replace the keyboard (see Replacing the Keyboard).
7. Replace the memory module(s) (see Replacing the Memory Module(s)).
8. Replace the module cover (see Replacing the Module Cover).
9. Follow the instructions from step 3 to step 4 in Replacing the Optical Drive.
10. Follow the instructions from step 4 to step 5 in Replacing the Hard Drive.
11. Replace the battery (see Replacing the Battery).
Display Bezel
Removing the Display Bezel
1. Follow the instructions in Before You Begin.
2. Remove the display assembly (see Removing the Display Assembly).
3. Make a note of the Mini-Card antenna cables and the display cable routing on the display hinges.
4. Using your fingertips, carefully pry up the inside edge of the display bezel.
5. Remove the display bezel.
1
display assembly
2
screws (2)
3
Mini-Card antenna
cables
4
display cable
connector
CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.
CAUTION: The display bezel is extremely fragile. Be careful when removing it to prevent damaging the bezel.
Replacing the Display Bezel
1. Follow the instructions in Before You Begin.
2. Route the Mini-Card antenna cables and the display cable on the display hinges.
3. Realign the display bezel over the display panel, and gently snap into place.
4. Replace the display assembly (see Replacing the Display Assembly).
Display Panel
Removing the Display Panel
1. Follow the instructions in Before You Begin.
2. Remove the display assembly (see Removing the Display Assembly).
3. Remove the display bezel (see Removing the Display Bezel).
4. Disconnect the camera cable from the connector on the camera module.
5. Remove the six screws that secure the display panel to the display cover.
6. Lift the display panel off the display cover.
7. Turn the display panel over and place it on a clean surface.
8. Lift the tape that secures the display cable to the display-board connector and disconnect the display cable.
9. Remove the camera cable.
1
display bezel
2
display hinges (2)
1
display panel
2
screws (6)
3
display cover
4
camera cable connector
NOTE: The camera cable is affixed to the back of the display panel.
10. Remove the four screws (two on each side) that secure the display-panel brackets to the display panel.
Replacing the Display Panel
1. Follow the instructions in Before You Begin.
2. Replace the four screws (two on each side) that secure the display-panel brackets to the display panel.
3. Adhere the camera cable at the back of the display panel.
4. Connect the display cable to the display-board connector and secure it with the tape.
5. Align the screw holes on the display panel with the screw holes on the display cover and replace the six screws.
6. Connect the camera cable to the connector on the camera module.
7. Replace the display bezel (see Replacing the Display Bezel).
8. Replace the display assembly (see Replacing the Display Assembly).
Back to Contents Page
1
display cable
2
back of the display
panel
3
display-board
connector
4
tape
1
screws (4)
2
display-panel brackets (2)
CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.
This manual suits for next models
2
Table of contents
Other Dell Laptop manuals
Dell
Dell Latitude D630 XFR User manual
Dell
Dell Inspiron 17R 5720 User manual
Dell
Dell Latitude PP06S User manual
Dell
Dell Vostro 1500 User manual
Dell
Dell Latitude 7400 2-in-1 User guide
Dell
Dell Latitude NH424 User manual
Dell
Dell Precision 7730 User manual
Dell
Dell Networking 8100 Series User manual
Dell
Dell Latitude 5501 User guide
Dell
Dell Vostro 1400 Specification sheet
Dell
Dell Inspiron 3520 Operation and maintenance manual
Dell
Dell Latitude 5430 How to use
Dell
Dell Inspiron 17 5000 Series User manual
Dell
Dell OptiPlex 7440 Operation and maintenance manual
Dell
Dell D630 - LATITUDE ATG NOTEBOOK User manual
Dell
Dell Latitude E5470 User manual
Dell
Dell Precision 7740 User guide
Dell
Dell Vostro 3000 User guide
Dell
Dell Latitude E4200 User manual
Dell
Dell Latitude CPx J Series User manual
Popular Laptop manuals by other brands
Lenovo
Lenovo IdeaPad Y560 Hardware Maintenance Manual
Samsung
Samsung NP300E5C Series 3 15.6" Notebook user guide
Asus
Asus P6300 Series installation guide
Lenovo
Lenovo IdeaPad N585 Säkerhetsinformation och allmän information
Lenovo
Lenovo ThinkPad X131e user guide
NEC
NEC VERSA 500D WINDOWS 98 - UPGRADE INFORMATION manual
Sony
Sony VAIO VPCEB24FX/WI Specifications
Dynatech
Dynatech iTronix XC 6 Series Technical bulletin
HP
HP Compaq Presario CQ57 Maintenance and service guide
Elonex
Elonex Webbook LNXWB10LSHD80 user manual
Toshiba
Toshiba L305 S5875 - Satellite - Pentium Dual Core 1.86... Specifications
Lenovo
Lenovo ThinkPad T430u Setup guide