DeLonghi ECAM25462 User manual

5713220781/08.13

DE
GB
ECAM25462/ECAM25467
BEAN TO CUP ESPRESSO
AND CAPPUCCINO MACHINE
Instruction for use

2
C
C7
C5
BC1
C4
C6
B1
B2
B3
B4
B5
B10
B9
B8
B7
B6
D
C2
C3
D1
D2
D3
D4
2

33
A14
A20
A19
A17
A18
A15
A
A16
A13
PUSH
A11
A12
A10
A8
A9
A1
A2 A5
A6
A7
A4
A3

4
PUSH
B
A
A B
34A
4B
5
911 12
13 14 16
1817 19
23
28
29
30 32
31
21
12
15
20
12
24
6 7 8
10 25
22
26A
26B
PUSH
27
4

5
PUSH
B
A
A B
34A
4B
5
911 12
13 14 16
1817 19
23
28
29
30 32
31
21
12
15
20
12
24
6 7 8
10 25
22
26A
26B
PUSH
27
5

6
CORD CLAMP
INTRODUCTION .......................................................7
Symbols used in these instructions...........................................7
Letters in brackets..................................................................... 7
Troubleshooting and repairs .....................................................7
SAFETY ...................................................................7
Fundamental safety warnings ..................................................7
DESIGNATED USE .....................................................7
INSTRUCTIONS FOR USE...........................................8
DESCRIPTION ..........................................................8
Description of the appliance ..................................................... 8
Description of the control panel................................................8
Description of the accessories ...................................................8
Description of milk container....................................................8
PRELIMINARY CHECKS .............................................8
Checking the appliance............................................................. 8
Installing the appliance ............................................................8
Connecting the appliance .........................................................9
Setting up the appliance........................................................... 9
TURNING THE APPLIANCE ON ...................................9
TURNING THE APPLIANCE OFF..................................9
MENU SETTINGS ....................................................10
Descaling ................................................................................ 10
Install lter .............................................................................10
Replacing the lter .................................................................10
Adjust time ............................................................................. 10
Auto-start............................................................................... 10
Auto-O..................................................................................10
Cup warmer ............................................................................10
Energy saving..........................................................................10
Setting the temperature .........................................................10
Setting water hardness........................................................... 11
Enable/disable the beep .........................................................11
Setting the language .............................................................. 11
Cup lighting ............................................................................11
Default values (reset)..............................................................11
Statistics function ................................................................... 11
MAKING COFFEE ....................................................11
Selecting the coee avour.....................................................11
Selecting the quantity of coee in the cup..............................11
Customising the“my coee”quantity ..................................... 12
Adjusting the coee mill......................................................... 12
Tips for a hotter coee ............................................................12
Making coee using coee beans........................................... 12
Making coee using pre-ground coee ..................................12
MAKING CAPPUCCINO AND MILK BASED COFFEES ....13
Filling and attaching the milk container .................................13
Adjusting the amount of froth ................................................ 13
Preparing cappuccino.............................................................. 13
Making CAFFELATTE/MACCHIATO/FLAT WHITE/ MILK...........13
Cleaning the milk container after each use.....................14
Programming the quantities of coee and milk in the cup .....14
Programming cappuccino:...................................................... 14
Programming the MILK MENU drinks:.....................................14
MAKING HOT WATER ..............................................14
Changing the quantity of water delivered automatically ........14
CLEANING .............................................................15
Cleaning the machine............................................................. 15
Cleaning the coee grounds container.................................... 15
Cleaning the drip tray and condensate tray............................. 15
Cleaning the inside of the coee machine .............................. 15
Cleaning the water tank.......................................................... 15
Cleaning the coee spouts......................................................15
Cleaning the pre-ground coee funnel................................... 15
Cleaning the infuser................................................................ 15
Cleaning the milk container.................................................... 16
Cleaning the hot water/steam nozzle .....................................16
DESCALING............................................................16
SETTING WATER HARDNESS....................................17
Measuring water hardness......................................................17
Seting water hardness ............................................................ 17
WATER SOFTENER FILTER .......................................18
Installing the lter.................................................................. 18
Replacing the lter .................................................................18
Removing the lter.................................................................18
TECHNICAL DATA.......................................................................18
DISPOSAL ....................................................................................18
DISPLAYED MESSAGES ...........................................19
TROUBLESHOOTING...............................................20

7
INTRODUCTION
Thank you for choosing this automatic espresso and cappuccino
machine. We hope you enjoy using your new appliance.
Take a few minutes to read this Instruction for Use.
This will avoid all risks and damage to the appliance.
Symbols used in these instructions
Important warnings are identied by these symbols. It is vital
to respect these warnings.
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Please note :
This symbol identies important advice or information for the
user.
Letters in brackets
The letters in brackets refer to the legend in the Description of
the Appliance on page 3.
Troubleshooting and repairs
In the event of problems, rst try and resolve them following
the information given in the sections“Displayed messages”on
page 19 and“Troubleshooting”on page 20.
If this does not resolve the problem or you require further infor-
mation, you should consult customer assistance by calling the
number given on the attached "Customer Assistance" leaet.
If your country is not among those listed on the sheet, call the
number given in the warranty. If repairs are required, contact
De’Longhi customer experience only. The addresses are given
in the guarantee certicate provided with the machine.
SAFETY
Fundamental safety warnings
Danger!
This is an electrical appliance and thus could cause electric
shock.
You should therefore respect the following safety warnings:
• Nevertouchtheappliancewithdamphandsorfeet.
• Nevertouchtheplugwithdamphands.
• Makesurethesocketusedisfreelyaccessibleatalltimes,
enabling the appliance to be unplugged when necessary.
• Unplugdirectlyfromtheplugonly.Neverpullthepower
cable as you could damage it.
• Todisconnecttheappliancecompletely,releasethemain
switch at the back of the appliance (g. 2).
• Iftheapplianceisfaulty,donotattempttorepair.
Turn it o, unplug it from the mains socket and contact
customer assistance.
• Iftheplugorpowercableisdamaged,itmustbereplaced
by De’Longhi Customer Services only to avoid all risk.
Important!
• Keep all packaging material (plastic bags, polystyrene
foam) away from children.
• Theapplianceisnotintendedforusebypersons(inclu-
ding children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concer-
ning use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the appliance.
Danger : Risk of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
DESIGNATED USE
This appliance is designed and made to prepare coee and heat
drinks.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from im-
proper use of the appliance.
This is a household appliance only. It is not intended to be used
in:
• sta kitchen areas in shops, oces and other working
environments;
• farmhouses;
• byclientsinhotels,motelsandotherresidentialtypeen-
vironments;
• bedandbreakfasttypeenvironments.

8
INSTRUCTION FOR USE
Read these instructions carefully before using the appliance.
- Failure to respect these instructions may result in burns or
damage to the appliance.
The manufacturer is not liable for damage deriving from
failure to respect these instructions for use.
Please note :
Keep these instructions. If the appliance is passed on to other
persons, they must also be provided with these instructions for
use.
DESCRIPTION
Description of the appliance
(page 3 - A )
A1. Control panel
A2. Grinding adjustment dial
A3. Cup shelf (cup warmer active when selected from set-
tings menu)
A4. Bean container lid
A5. Pre-ground coee funnel lid
A6. Pre-ground coee funnel
A7. Bean container
A8. Main switch
A9. Socket for power cable connector
A10. water tank
A11. Infuser door
A12. infuser
A13. Coee spout (adjustable height)
A14. Coee grounds container
A15. Condensate tray
A16. Cup tray
A17. Drip tray water level indicator
A18. Drip tray
A19. Cup lighting
A20. Hot water and steam connection nozzle
Description of the control panel
(page 2 - B )
Some keys on the panel have a double function: this is shown in
parenthesis inside the description.
B1. Display: guides the user in using the appliance.
B2. Button : turns the appliance on and o.
B3. MENU button to access the menu
B4. Button : to perform a rinse cycle.
(When in the settings MENU, it acts as the “ESC” button
to exit from the selected function and go back to the main
menu).
B5. CAPPUCCINO BUTTON: to prepare a cappuccino.
B6. Selection dial:
- rotate it to select the amount of coee desired.
- press to select the desired avour.
(When in the settings MENU: turn to select the required fun-
ction).
B7. MILK MENU button: to access preparation of MACCHIATO,
CAFFELATTE, FLAT WHITE and MILK.
B8. Button : to deliver hot water.
(When in the MENU: press the "OK" button to conrm the
item chosen)
B9. Button : to make 2 cups of coee
B10. Button : to make 1 cup of coee
Description of the accessories
(page 2 - C )
C1. Measure
C2. Cleaning brush
C3. Hot water spout
C4. Water softener lter (certain models only)
C5. “Total HardnessTest”indicator paper
C6. Power cable
C7. Descaler
Description of milk container
(page 3 - D )
D1. Froth adjustment and CLEAN dial
D2. Frothed milk spout (adjustable)
D3. Milk intake tube
D4. Milk container
PRELIMINARY CHECKS
Checking the appliance
After removing the packaging, make sure the product is com-
plete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact De’Lon-
ghi customer assistance.
Installing the appliance
Important!
When installing the appliance, you should respect the fol-
lowing safety warnings:
• The appliance gives o heat. After positioning the ap-
pliance on the worktop, leave a space of at least 3 cm
between the surfaces of the appliance and the side and
rear walls and at least 15 cm above the coee machine.
• Waterpenetratingtheappliancecouldcausedamage.
Do not place the appliance near taps or sinks.
• Theappliancecouldbedamagedifthewateritcontains
freezes.
Do not install the appliance in a room where the tempera-
ture could drop below freezing point.
• Arrangethepowercableinsuchawaythatitcannotbe
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).

9
Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Connecttheappliancetoanecientlyearthedandcorrectly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied
professional.
Setting up the appliance
Please note :
• Coeehasbeenusedtofactorytesttheapplianceanditis
therefore completely normal for there to be traces of cof-
fee in the mill.The machine is, however, guaranteed to be
new.
• Youshouldcustomisewaterhardnessassoonaspossible
following the Instruction for use in the section “Setting
water hardness”on page 17.
1. Plug the power cable connector into the socket at the back
of the appliance and connect the appliance to the mains
electricity supply (g. 1) making sure the main switch on
the back of the appliance is pressed (g. 2).
You must rst choose the language by turning the selection
dial, or waiting until the languages scroll through on the di-
splay at intervals of about 3 seconds:
2. When“English”appears, press the button (g. 3) for
a few seconds until“English set”is displayed.
Follow the instructions indicated on the appliance display:
3. “FILL TANK”: remove the water tank, ll to the MAX line
with fresh water (g. 4A), then replace in the appliance
(g. 4B).
4. “INSERT WATER SPOUT”: Check that the hot water spout
is inserted on the nozzle and place a container with a mi-
nimum capacity of 100 ml under the cappuccino maker
(g. 5).
5. “HOT WATER CONFIRM?”is displayed;
6. Press the button to conrm: the appliance delivers
water from the spout then goes o automatically.
The coee machine is now ready for normal use.
Please note :
• Whenusingtheapplianceforthersttime,youneedto
make 4-5 cups of coee or 4-5 cappuccinos before it starts
to give satisfactory results.
• Whenmakingthe rst 5-6 cappuccinos,it isnormalto
hear the noise of boiling water: the noise will diminish.
• Toenjoyyourcoeeevenmoreandimprovetheperfor-
mance of your appliance, we recommend installing a wa-
ter softener lter as described in the section“Install lter”.
If your model is not provided with a lter, you can request
one from De’Longhi Customer Service.
TURNING THE APPLIANCE ON
Please note :
Before turning the appliance on, make sure the main switch on
the back of the appliance is pressed (g. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The ap-
pliance is ready for use only after completion of this cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coee spouts
and is collected in the drip tray underneath. Avoid contact with
splashes of water.
• Toturntheapplianceon,pressthe button (g. 6).
The message“Heating up Please wait”is displayed.
After heating, the message“Rinsing”is displayed; in this man-
ner, besides heating the boiler, the appliance also heats the
internal circuits by circulating hot water.
The appliance is at temperature when the message indicating
the avour and quantity of coee appears.
TURNING THE APPLIANCE OFF
Each time the appliance is turned o it performs an automatic
rinse if a coee has been prepared.
Danger of burns!
During rinsing, a little hot water ows from the coee spouts.
Avoid contact with splashes of water.
To turn the appliance o, press the button (g. 6). The
appliance performs a rinse cycle then goes o (stand-by).
Please note :
If you will not be using the appliance for a long time, unplug it
from the mains socket:
• rstturntheapplianceobypressingthe button
(g. 6);
• pressthemainswitch(g.2).
Important!
Never press the main switch while the appliance is on.

10
MENU SETTINGS
Access the settings menu by pressing the MENU button; the
following menu items are available:
Descaling
For instructions on descaling, see page 16.
Install lter
For instructions on how to install the lter, see the section“In-
stalling the lter (page 18).
Replacing the lter
For instructions on how to replace the lter, see the section
“Replacing the lter”(page 18.
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the MENU button to enter the menu;
2. Turn the selection dial (g. 7) until“Adjust time”is displa-
yed;
3. Press ;
4. Turn the selection dial to change the hours;
5. Press to conrm;
6. Turn the selection dial to change the minutes;
7. Press to conrm.
The time is now set: Then press to exit the menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note :
To enable this function, the time must already be set correctly.
1. Press the MENU button to enter the menu;
2. Turn the selection dial until“Auto-start”is displayed;
3. Press : "Enable?" will appear on the display;
4. Press the button to conrm.
5. Turn the selection dial to choose the hours;
6. Press to conrm;
7. Turn the selection dial to change the minutes;
8. Press to conrm;
9. Then press to exit the menu.
Once the time is conrmed, the auto-start activation is shown
on the display with the symbol that is displayed next to
the time and below the Auto-start item on the menu.
To disable the function:
1. Select auto-start from the menu;
2. Press : "Disable?" will appear on the display;
3. Press the button to conrm.
The display no longer shows the symbol.
Auto-O
Auto-o can be set so that the appliance goes o after 15 or 30
minutes, or after 1, 2 or 3 hours.
1. Press the MENU button to enter the menu;
2. Turn the selection dial until“Auto-O”is displayed;
3. Press ;
4. Turn the selection dial until the desired operation time is
displayed (15 or 30 minutes, or 1, 2 or 3 hours);
5. Press the button to conrm.
Auto-o has been reprogrammed: press to exit the menu.
Cup warmer
This function enables the cup warmer to be enabled or disa-
bled. Proceed as follows:
1. Press the MENU button to enter the menu;
2. Turn the selection dial until“Cup warmer”is displayed;
3. Press :“Enable?”or“Disable?”is displayed;
4. Press to enable or disable the cup warmer (an asterisk
under "CupWarmer" shows that it is active).
5. Then press the button to exit the menu.
Warming the cups keeps the coee hot.
Energy saving
Use this function to enable or disable Energy saving.When ena-
bled, the function reduces energy consumption in compliance
with current European regulations.
When energy saving mode is active, an asterisk appears below
“Energy saving”in the menu.
1. Press the MENU button to enter the menu;
2. Turn the selection dial until“Energy saving”is displayed;
3. Press :“Enable?”or“Disable?”is displayed;
4. Press to enable or disable the energy saving mode;
Then press to exit the menu.
When the function is active, if the machine is not used for some
time,“Energy saving”is displayed.
Please note:
• Wheninenergysavingmode,afewsecondselapsebefore
the rst coee, cappuccino or milk based coee is delive-
red as the appliance must heat up again.
• Toprepareanydrink,pressanybuttontoexitenergysa-
ving, then press the button corresponding to the drink you
want to make.
• Ifthemilkcontainerisinserted,“Energysaving”isnotac-
tivated.
Setting the temperature
To modify the temperature (low, medium, high) of the water
used to make the coee, proceed as follows:
1. Press the MENU button to enter the menu;

11
2. Turn the selection dial until “Set temperature” is displa-
yed;
3. Press the button.
4. Turn the selection dial until the desired temperature
(l=low; llll =high) is shown on the display.
5. Press to conrm.
The temperature has been reprogrammed: press to exit
the menu.
Setting water hardness
For instructions on setting water hardness, see page 17.
Enable/disable the beep
This enables or disables the beep emitted by the machine each
time an icon is pressed or an accessory is inserted/removed. To
disable or re-enable the beep, proceed as follows:
1. Press the MENU button to enter the menu;
2. Turn the selection dial until“Beep”is displayed;
3. Press :“Enable?”or“Disable?”is displayed;
4. Press the button to enable or disable the beep;
5. When the function is enabled an asterisk appears under
"Beep" in the menu.
Then press to exit the menu.
Setting the language
To modify the language on the display, proceed as follows:
1. Press the MENU button to enter the menu;
2. Turn the selection dial until“Set language”is displayed;
3. Press ;
4. Turn the selection dial until the desired language is di-
splayed;
5. Press to conrm;
6. A message conrming the language installed is displa-
yed;
7. Then press the button to exit the menu.
Cup lighting
This function enables or disables the cup lighting. When the
function is active, the lighting comes on whenever cappuccino
or milk based drinks are made or the appliance is rinsed.
To disable or re-enable this function, proceed as follows:
1. Press the MENU button to enter the menu;
2. Turn the selection dial until“Cup lighting”is displayed.
3. Press :“Enable?”or“Disable?”is displayed;
4. Press the button to enable or disable the cup lighting;
5. When the function is active, an asterisk appears under
“Cup lighting”in the menu.
Then press to exit the menu.
Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language
which remains as set).
1. Press the MENU button to enter the menu;
2. Turn the selection dial until“Default values”is displayed;
3. Press ;
4. Conrm?”is displayed.
5. Press to conrm and exit.
Statistics function
This displays statistics relating to the machine. To display, pro-
ceed as follows:
1. Press the MENU button to enter the menu;
2. Turn the selection dial until“Statistics”is displayed;
3. Press the button.
4. Turn the selection dial to verify:
- how many coees have been made;
- how many drinks have been made using milk;
- the total number of litres of water delivered;
- how many times the machine has been descaled.
- how many times the water softener lter has been repla-
ced.
5. Press the button twice to exit the menu.
MAKING COFFEE
Selecting the coee avour
The appliance is set by default to make coee with a standard
avour.
You can also choose one of these avours:
Extra-mild
Mild
Standard
Strong
Extra-strong
To change the taste, press the dial (g. 7) repeatedly
until the required taste is displayed.
Selecting the quantity of coee in the cup
To select the quantity of coee, turn the selection dial (g. 8)
until the message corresponding to the required quantity of
coee is displayed:

12
Coee selected Quantity in cup (ml)
MY COFFEE ≃30 (program.
from ≃20 to ≃180)
SHORT ≃40
STANDARD ≃60
LONG ≃90
EXTRA LONG ≃120
Customising the “my coee”quantity
The machine is preset to deliver about 30ml of "MY COFFEE“.To
modify this quantity, proceed as follows:
1. Place a cup under the coee spouts (g. 9).
2. Turn the selection dial (g. 8) until “MY COFFEE”is displa-
yed.
3. Keep the button (g. 10) pressed until the message
“1 MY COFFEE Program quantity” is displayed and coee
delivery begins. Release the button.
4. As soon as the coee in the cup reaches the required level,
press the button (g. 10) again.
The quantity of coee in the cup has now been programmed.
Adjusting the coee mill
The coee mill is set by default to prepare coee correctly and
should not require regulating initially.
However, if after making the rst few coees you nd that the
coee is either too weak and not creamy enough or delivery
is too slow (in drops), this can be corrected by adjusting the
grinding adjustment dial (g. 11).
Please note :
The grinding adjustment dial must only be turned when the
coee mill is in operation.
If the coee comes out too slowly or
doesn't come out at all, turn the dial
one time to number 7.
For fuller bodied creamier coee,
turn one click anticlockwise towards
“1” (do not turn more than one click
at a time otherwise the coee could
be delivered a drop at a time).
These adjustments will only be evident after at least 2 cups of
coee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
Tips for a hotter coee
For hotter coee, you should:
• rinsebeforedeliveringcoeebypressingthe but-
ton: hot water will come out of the spout that heats the
circuit inside the machine making the coee hotter;
• warmthecupswithhotwater(usingthehotwaterfun-
ction);
• enablethecupwarmerinthesettingsmenuandleave
the cups until they are warm;
• raisethecoeetemperatureinthesettingsmenu.
Making coee using coee beans
Important!
Do not use caramelised or candied coee beans as they could
stick to the coee mill and make it unusable.
1. Fill the container with coee beans (g. 12).
2. Place under the coee spouts:
- 1 cup, if you want to make 1 coee (g. 9);
- 2 cups, if you want 2 coees (g. 13);
3. Lower the spout as near as possible to the cups: this will
make it creamier (g. 14).
4. Press the button corresponding to the number of coees
required (1 cup or 2 cups ).
5. The preparation starts and the display shows the coee
selected and a progression bar that lls gradually as the
coee is prepared.
Once the coee has been made, the appliance is ready to make
the next drink.
Please note :
While the appliance is making coee, the ow can be in-
terrupted at any moment by pressing any button.
• Attheendofdelivery,toincreasethequantityofcoee
in the cup, just press and hold one of the coee buttons
(within 3 seconds) ( or ).
Please note :
For hotter coee, consult the paragraph "Tips for hotter cof-
fee“.
Important!
• Ifthecoeeisdeliveredadropatatime,tooweakand
not creamy enough or too cold, read the tips in the“Trou-
bleshooting”section on page 20.
• Variousalarm messagescouldbedisplayedwhileusing
the machine (FILL TANK, EMPTY GROUNDS CONTAINER,
etc). Their meaning is explained in the section“Displayed
messages”(page 19).
Making coee using pre-ground coee
Important!
• Neverplacecoeebeansin the
pre-ground coee funnel as this
could damage the appliance.
• Never add pre-ground coee
when the machine is o or it

13
could spread through the inside of the machine and dirty
it.This could damage the appliance.
• Neverusemorethanonelevelmeasureoritcoulddirty
the inside of the machine or block the funnel.
Please note :
When you use pre-ground coee, you can only make one cup
of coee at a time.
1. Make sure the appliance is on.
2. Press the dial (g. 7) repeatedly until “Pre-
ground”is displayed.
3. Make sure the funnel is not blocked, then add one level
measure of pre-ground coee (g. 15).
4. Place a cup under the coee spouts.
5. Press the 1 cup dispensing button .
6. The preparation starts and the display shows the coee
selected and a progression bar that lls gradually as the
coee is prepared.
Please note:
If“Energy Saving”mode is enabled, you may have to wait a few
seconds before the rst cappuccino is dispensed.
MAKING CAPPUCCINO AND MILK BASED
COFFEES
Please note:
• Toavoidproducingmilkwithpoorfrothorlargebubbles,
always clean the milk container lid and hot water connec-
tion nozzle as described in the section “Cleaning the milk
container”on pages 14 and 16.
Filling and attaching the milk container
1. Remove the lid (g. 16);
2. Fillthemilkcontainerwithasucientquantityofmilk,
not exceeding the MAX level marked on the handle (g.
17). Each mark on the side of the container corresponds to
100 ml of milk.
Please note:
• Foradensermoreevenfroth,youmustuseskimmedor
partially skimmed milk at refrigerator temperature (about
5°C).
If“energy saving”mode is enabled, you may have to wait
a few seconds before the rst cappuccino is delivered.
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (g. 18).
4. Attach the lid back on the milk container.
5. Attach the container to the connection nozzle and push as
far as it will go (g. 19). The machine emits a beep.
6. Placeasucientlylargecupunderthecoeeandfrothed
milk spouts. Adjust the length of the milk spout. To move
it nearer the cup, simply pull it downwards (g. 20).
7. Follow the instructions below for each function.
Adjusting the amount of froth
Turn the froth adjustment dial on the milk container lid to
adjust the amount of froth on the milk delivered while making
milk drinks (g. 21). Follow the tips in the table below:
Dial
position
Description Recommended for…
No froth CAFFELATTE /
MILK (hot milk)
Min. froth LATTE MACCHIATO /
FLAT WHITE
Max. froth CAPPUCCINO /
MILK frothy milk
Preparing cappuccino
1. After attaching the milk container, turn the froth regula-
tor on the milk container lid to the required position (g.
21).
2. Press the CAPPUCCINO button.“CAPPUCCINO”is displayed,
together with a progress bar which lls gradually as pre-
paration proceeds.
3. After dispensing the milk, the machine automatically ma-
kes the coee.
Please note:
• Ifduringdispensingyouwanttostoppreparation,press
the CAPPUCCINO BUTTON TWICE.
• At the end of delivery, to increase the quantity of milk or
coee in the cup, within 3 seconds, press and hold the
CAPPUCCINO button.
• Do not leave the milk container out of the refrigerator for
long periods.The warmer the milk (5°C is ideal), the poo-
rer the quality of froth produced.
Making CAFFELATTE/MACCHIATO/FLAT WHITE/ MILK
1. After attaching the milk container, turn the froth regula-
tor on the milk container lid to the required position (g.
21).
2. Press MILK MENU.
3. Turn the selection dial until the required drink is displayed
(CAFFELATTE, MACCHIATO, FLAT WHITE, MILK);
4. Press MILK MENU to conrm: the display will show the
name of the drink selected and a progression bar that lls
gradually as the coee is prepared.
5. After a few seconds, milk is dispensed from the milk spout
into the cup below. Milk dispensing stops automatically

14
and (if needed for the drink), coee delivery starts.
Pease note:
• Milkorcoeedispensingcanbeinterruptedatanytime
by pressing the CAPPUCCINO or MILK MENU button accor-
ding to the drink selected.
• At the end of delivery, to increase the quantity of milk or
coee in the cup, within 3 seconds, press one of the but-
tons for milk-based drinks.
• Do not leave the milk container out of the refrigerator for
long periods.The warmer the milk (5°C is ideal), the poo-
rer the quality of froth produced.
Cleaning the milk container after each use
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout. Avoid
contact with splashes of water.
“SET DIAL TO CLEAN” ashes on the display each time you use
a milk function. To eliminate all milk residues, proceed as fol-
lows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Turn the froth adjustment dial to“CLEAN”(g. 22). A pro-
gress bar appears and gradually lls as the operation pro-
ceeds together with“Cleaning underway”. Cleaning stops
automatically.
4. Turn the dial back to one of the froth selections.
5. Remove the milk container and always clean the steam
nozzle with a sponge (g. 26).
Please note:
• Toprepareanumberofcappuccinosormilkbaseddrinks,
clean the milk container after you have prepared the last
drink only.
• Themilkcontainercanbekeptintherefrigerator.
• Insomecases,tocleanyoumustwaitfortheapplianceto
heat up.
Programming the quantities of coee and milk in the
cup
Theappliance isset bydefault toautomaticallydeliverstandard
quantities.To change these quantities, proceed as follows:
1. Place a cup under the coee spouts and milk spout.
Programming cappuccino:
2. Hold the CAPPUCCINO button until the message “CAP-
PUCCINO PROGRAM MILK”IS DISPLAYED.
3. The appliance starts dispensing milk. Release the button.
4. Once the required quantity of milk has been delivered into
the cup, press the CAPPUCCINO button again.
5. After a few seconds, the appliance starts delivering coee
into the cup and the message “ CAPPUCCINO PROGRAM
COFFEE”is displayed.
6. Once the required quantity of coee has been delivered
into the cup, press the CAPPUCCINO button.
Coee delivery stops and the machine is“ready for use”again.
This completes programming.
Programming the MILK MENU drinks:
2. Press MILK MENU.
3. Turn the selection dial until the drink you want to pro-
gramme again is displayed (CAFFELATTE, MACCHIATO,
FLAT WHITE, MILK);
4. Hold down the MILK MENU button for a few seconds un-
til “(DRINK) PROGRAM MILK" IS DISPLAYED.
5. The appliance starts dispensing milk. Release the button.
6. Once the required quantity of milk has been delivered into
the cup, press the MILK MENU button again.
7. After a few seconds, if required by the drink, the appliance
starts delivering coee into the cup and the message “
(DRINK) PROGRAM COFFEE”is displayed.
8. Once the required quantity of coee has been delivered
into the cup, press the MILK MENU BUTTON.
Coee delivery stops and the machine is“ready for use”again.
This completes programming.
MAKING HOT WATER
Danger of burns!
Never leave the machine unsupervised while hot water is being
delivered.
1. Make sure the hot water spout is attached correctly.
2. Place a container under the water spout (as close as possi-
ble to avoid splashes) (g. 5).
3. Press the button. “Hot water” is displayed, together
with a progress bar which lls gradually as preparation
proceeds.
4. Hot water delivery begins and then stops automatically.
To manually stop dispensing hot water, press .
Please note :
If “Energy saving” mode is active, you may have to wait a few
seconds before the hot water is delivered.
Changing the quantity of water delivered automati-
cally
The machine is set by default to automatically dispense 250 ml

15
of hot water. To modify these quantities, proceed as follows:
1. Make sure the hot water spout is attached correctly.
2. Position a container under the spout.
3. Press and hold the button until“HOT WATER Program
quantity”is displayed, then release.
4. When the hot water in the cup reaches the required level,
press the BUTTON.
The machine is now reprogrammed with the new quantity.
CLEANING
Cleaning the machine
The following parts of the machine must be cleaned regularly:
- coee grounds container (A14),
- drip tray (A18) and condensate tray (A15),
- water tank (A10),
- coee spouts (A13) and hot water nozzle (A20),
- pre-ground coee funnel (A6),
- inside of the machine, accessible after opening the infuser
door (A11),
- infuser (A12).
- milk container (D)
Important!
• Donotusesolvents,abrasivedetergentsoralcoholtocle-
an the appliance.With De’Longhi superautomatic bean to
cup espresso and cappuccino machines, you need not use
chemical products to clean the machine.
• Noneofthecomponentscanbewashedinadishwasher.
• Donotusemetalobjectstoremoveencrustationsorcoee
deposits as they could scratch metal or plastic surfaces.
Cleaning the coee grounds container
When“EMPTY GROUNDS CONTAINER”is displayed, the groun-
ds container must be emptied and cleaned. Until the grounds
container has been cleaned, the appliance continues to display
the message and coee cannot be made.
To clean (with the machine on):
• Removethedriptray(g.23),emptyandclean.
• Empty the grounds container and clean thoroughly to
remove all residues left on the bottom. This can be done
with the spatula on the brush provided.
• Checkthecondensatetrayandemptyifnecessary.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coees, the groun-
ds container may ll up more than expected and clog the ma-
chine.
Cleaning the drip tray and condensate tray
Important!
The drip tray is tted with a level indicator (red) showing the
level of water it contains (g. 24). Before the indicator protru-
des from the cup tray, the drip tray must be emptied and clea-
ned, otherwise the water may overow the edge and damage
the appliance, the surface it rests on or the surrounding area.
To remove the drip tray:
1. Remove the drip tray and grounds container (g. 23);
2. Empty the drip tray and grounds container and wash
them;
3. Check the condensate tray and empty if necessary.
4. Replace the drip tray complete with grounds container.
Cleaning the inside of the coee machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned o
(see“Turning o”) and unplugged from the mains power sup-
ply. Never immerse the coee machine in water.
1. Check regularly (about once a week) that the inside of the
appliance (accessible after removing the drip tray) is not
dirty. If necessary, remove coee deposits with the brush
supplied and a sponge.
2. Remove the residues with a vacuum cleaner (g. 25).
Cleaning the water tank
1. Cleanthe watertank(A10)regularly(aboutonce a month)
and whenever you replace the water softener lter (if pro-
vided) with a damp cloth and a little mild washing up
liquid.
2. Remove the lter (if present) and rinse with running wa-
ter.
3. Replace the lter (if provided), ll the tank with fresh wa-
ter and replace the tank.
Cleaning the coee spouts
1. Clean the coee spouts with a sponge or cloth (g. 26A).
2. Check the holes in the coee spout are not blocked. If
necessary, remove coee deposits with a toothpick (g.
26B).
Cleaning the pre-ground coee funnel
Check regularly (about once a month ) that the pre-ground
coee funnel (A6) is not blocked. If necessary, remove coee
deposits with the brush supplied (C2).
Cleaning the infuser
The infuser (A12) must be cleaned at least once a month.

16
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned o (see “Tur-
ning o”, page 9).
2. Extract the water tank.
3. Open the infuser door (g. 27) on the right side of the ap-
pliance.
4. Press the two red release buttons inwards and at the same
time pull the infuser outwards (g. 28).
Important!
RINSE WITH WATER ONLY NO WASHING UP LIQUID 
NO DETERGENTS  NO DISHWASHER
Clean the infuser without using washing up liquid as it
could be damaged.
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
6. Use the brush to remove any coee residues left in the
infuser housing, visible through the infuser door.
7. After cleaning, replace the infuser by sliding it onto the
internal support, then push the PUSH symbol fully in until
it clicks into place.
Please note :
Iftheinfuserisdiculttoinsert,beforeinsertion,adaptitto
the right size by pressing the two levers shown in the gure.
8. Once inserted, make sure the two red buttons have snap-
ped out.
9. Close the infuser door.
10. Replace the water tank.
Cleaning the milk container
Clean the milk container each time you prepare milk as descri-
bed below:
1. Remove the lid.
2. Remove the milk spout and
intake tube.
3. Turn the froth adjustment dial
clockwise to the “INSERT”
position (see gure) and
pull o upwards.
4. Wash all the components
thoroughly with hot wa-
ter and mild washing-up
liquid. All components are
dishwasher safe, placing
them in the top basket of
the dishwasher. Make sure
there are no milk residues
on the hollow and groove
under the dial (see gure
alongside). If necessary, scrape
the groove with a toothpick.
5. Rinse inside the froth
adjustment dial seat with run-
ning water (see gure).
6. Check that the intake tube
and spout are not clogged
with milk residues.
7. Replace the dial (lining up
the arrow with the word
“INSERT”), the spout and the
milk intake tube.
8. Place the lid back on the milk
container.
Cleaning the hot
water/steam nozzle
Each time you prepare
milk, clean the nozzle
with a sponge to remo-
ve milk residues from
the gaskets (see gure
alongside).
DESCALING
Descale the machine when the message “DESCALE” FLASHES
ON THE DISPLAY.
PUSH
25

17
Important!
• Descaler containsacids which may irritatetheskinand
eyes. It is vital to respect the manufacturer’s safety war-
nings given on the descaler pack and the warnings re-
lating to the procedure to follow in the event of contact
with the skin and eyes.
• YoushoulduseDe’Longhidescaleronly.Usingunsuitable
descaler and/or performing descaling incorrectly may
result in faults not covered by the manufacturer’s guaran-
tee.
1. Turn the machine on.
2. Press the MENU button to enter the menu.
3. Turn the selection dial until“Descale”is displayed.
4. Select by pressing thebutton : “Descale Conrm?” is
displayed. Press again to enable the function.
5. The message “Add descaler Conrm?” is displayed, alter-
nating with “EMPTY THE DRIP TRAY” and “REMOVEFIL
TER”(if the lter is present).
6. Empty the water tank (A10) completely and remove the
water softener lter (if present). Empty the drip tray (g.
23) and grounds container, then put them back in the ap-
pliance.
7. Pour the descaler into the water tank up to the level A
(corresponding to a 100 ml pack) marked on the back of
the tank (g. 29), then add water (1 litre) up to level B
(g. 29). Replace the water tank.
8. Place an empty container with a minimum capacity of 1.5
litres under the hot water spout (g. 5).
Danger of burns!
Hot water containing acid ows out of the hot water spout.
Avoid contact with splashes of water.
9. Press the button to conrm that you have added the
solution.
10. The message“Descale underway”is displayed.The desca-
le programme starts and the descaler liquid comes out of
the water spout. The descale programme automatically
performs a series of rinses and pauses to remove limescale
deposits from inside the machine.
After about 30 minutes, the message“Rinsing”“INSERT FILTER”
(if present),“FILL TANK”is displayed.
11. The appliance is now ready for rinsing through with clean
water. Extract the water tank, empty, rinse under running
water, ll with clean water up to the MAX level, insert the
lter (if removed previously) and put the water tank back
in the machine.“RINSING Conrm?”is displayed.
12. Empty the container used to collect the descaler solution
and replace it empty under the cappuccino maker.
13. Press the button to starting rinsing. Hot water ows
out of the spout and the message “RINSING PLEASE
WAIT”is displayed.
14. When the water tank is completely empty, the message
“Rinsing complete Conrm?”is displayed.
15. Press the button to conrm.“FILL TANK”is displayed.
Fill and replace the water tank.
16. “Heating up Please wait”is displayed at the end of which
the machine will be ready for use.
SETTING WATER HARDNESS
The DESCALE message is displayed after a period of time esta-
blished according to water hardness.
The machine is set by default for a hardness value of 4. The ma-
chine can also be programmed according to the hardness of the
mains water in the various regions so that the machine needs
to be descaled less often.
Measuring water hardness
1. Remove the“TOTAL HARDNESSTEST”indicator paper from
its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3 or 4 red squares appear, depending
on the hardness of the water: each square corresponds to
one level.
soft water l
slightly hard water
ll
hard water lll
very hard water
llll
Set water hardness
1. Press the MENU button to enter the menu;
2. Turn the selection dial until“Water Hardness”is displayed;
3. Press the button.
4. Turn the selection dial and set the number of squares
measured by the indicator paper (see gure in previous
paragraph).
5. Press the button to conrm the setting.
6. Then press the button to exit the menu.
The machine is now reprogrammed with the new water
hardness setting.

18
WATER SOFTENER FILTER
Some models come supplied with the water softener lter. If
this is not the case with your model, we recommend purcha-
sing one from De’Longhi customer assistance.
To use the lter correctly, follow the instructions below.
Installing the lter
1. Remove the lter from the packaging.
2. Turn the date indicator disk (see g. 30) until the next two
months of use are displayed.
Please note :
The lter lasts about two months if the appliance is used regu-
larly. If the coee machine is left unused with the lter instal-
led, it will last a maximum of three weeks.
3. To activate the lter, run tap water through the hole in the
lter as shown in the gure until water comes out of the
openings at the side for more than a minute (g. 32).
4. Extract the tank from the appliance and ll with water.
5. Insert the lter in the water tank and immerse it com-
pletely for about ten seconds, sloping it to enable the air
bubbles to escape (g. 32).
6. Insert the lter in the lter housing and press as far as it
will go.
7. Close the tank with the lid, then put the tank back in the
machine.
When you install the lter, you must notify the appliance of its
presence.
8. Press the MENU button to enter the menu;
9. Turn the selection dial until“Install lter”is displayed;
10. Press the button.
11. “Enable?”is displayed;
12. Press the button to conrm the selection. “HOT WA
TER CONFIRM?”is displayed;
13. Position a container with a minimum capacity of 500ml
under the hot water spout.
14. Press the button to conrm the selection. The ap-
pliance begins hot water delivery and the message“Plea-
se wait”is displayed.
15. After delivery, the appliance is automatically ready to
make the next drink.
The new lter is active and
indicated by an asterisk displa-
yed under “Install lter” in the
menu. You can now use the
appliance.
Replacing the lter
When “REPLACE FILTER” is di-
splayed, or after two months
(see date indicator) or when the
appliance has not been used for
3 weeks, you should replace the
lter:
1. Extract the tank and exhausted lter;
2. Take the new lter out of its packet and proceed as illu-
strated in points 2, 3, 4, 5 and 6 in the previous section.
3. Position a container with a minimum capacity of 500ml.
4. Press the MENU button to enter the menu;
5. Turn the selection dial until“Replace lter”is displayed.
6. Press the button.
7. Conrm?”is displayed.
8. Press the button to conrm the selection;
9. “HOT WATER Conrm?”is displayed;
10. Press the button to conrm the selection. The ap-
pliance begins hot water delivery and the message“Plea-
se wait”is displayed.
11. After delivery, the appliance is automatically ready to
make the next drink.
The new lter is now active and you can use the coee ma-
chine.
Removing the lter
If you want to use the appliance without the lter, you must
remove it and notify the appliance of its removal. Proceed as
follows:
1. Extract the tank and exhausted lter;
2. Press the MENU button to enter the menu;
3. Turn the selection dial until“Install lter”is displayed;
4. Press the button.
5. “Disable?”is displayed;
6. Press to conrm and to exit the menu.
TECHNICAL DATA
Voltage: 220-240V~50/60Hzmax.10A
Absorbed power: 1450W
Pressure: 15 bar
Max. water tank capacity: 1.8 litres
Size: LxHxD: 238x351x430 mm
Cable length: 1,75 m
Weight: 9.1 kg
Max. beans container capacity: 250 g
The appliance complies with the following EC directives:
• ECRegulation1275/2008forstandby;
• Low Voltage Directive 2006/95/EC and subsequent
amendments;
• EMCDirective2004/108/ECandsubsequentamendments;
• Materialsandaccessoriescomingintocontactwithfood
conform to EC regulation 1935/2004.
DISPOSAL
In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with hou-
sehold waste, but taken to an authorised waste se-
paration and recycling centre.

19
DISPLAYED MESSAGES
MESSAGE DISPLAYED POSSIBLE CAUSE SOLUTION
FILL TANK Insucientwater in the tank. Fill the tank with water and/or insert it correctly, pushing
it as far as it will go until it clicks into place (g. 4).
EMPTY GROUNDS CONTAINER The grounds container (A14) is full. Empty the grounds container and drip tray, clean and
replace (g. 23). Important: When removing the drip
tray, the grounds container must be emptied, even if it
contains few grounds. If this is not done, when you make
the next coees, the grounds container may ll up more
than expected and clog the machine.
GROUND TOO FINE ADJUST
MILL
The grinding is too ne and the
coee is delivered too slowly or not
at all.
Repeat coee delivery and turn the grinding adjustment
dial (g. 11) one click clockwise towards “7” while the
coee mill is in operation.If after making at least 2 cof-
fees delivery is still too slow, repeat the correction proce-
dure, turning the grinding adjustment dial another click
until delivery is correct (see the grinding adjustment
section on page 12) If the problem persists, make sure
the water tank is fully inserted, press the button and
deliver a little water from the spout.
INSERT GROUNDS CONTAINER After cleaning, the grounds contai-
ner has not been replaced.
Remove the drip tray and insert the grounds container.
ADD PREGROUND COFFEE With the pre-ground function selec-
ted, pre-ground coee has not been
poured into the funnel.
Add pre-ground coee in the funnel or deselect the pre-
ground function.
DESCALE The machine must be descaled. The descaling procedure described in the section“Desca-
ling” needs to be performed as soon as possible (page
16).
LESS COFFEE Too much coee has been used. Select a milder avour or reduce the quantity of pre-
ground coee.
FILL BEANS CONTAINER The coee beans have run out. Fill the beans container.
The pre-ground coee funnel is
clogged.
Empty the funnel with the help of a brush as described in
the section“Cleaning the pre-ground coee funnel”.
INSERT INFUSER ASSEMBLY The infuser has not been replaced
after cleaning.
Insert the infuser as described in the paragraph“Cleaning
the infuser”(page 16).
INSERT TANK The tank was not inserted properly. Insert the tank correctly and press as far as it will go.
GENERAL ALARM The inside of the appliance is very
dirty.
Clean the inside of the appliance thoroughly, as descri-
bed in the section“Cleaning”(page 15). If the message is
still displayed after cleaning, contact a service centre.
REPLACE FILTER The water softener lter is exhau-
sted.
Replace the lter or remove it as described in the section
“Water softener lter”(page 18).