DeLonghi NSM 7 NL Quick guide

11
DE’LONGHI
COOKING
INSTALLATION and SERVICE INSTRUCTIONS
USE and CARE INSTRUCTIONS
NSM 7 NL
NSM 9 XL
NSM 9 NL
NSM 11 XL
NSM 11 NL
ELECTRIC BUILT-IN OVENS
distributed by
ELBA Appliances Australia
(a Division of Fisher&Paykel Australia)

22
Dear Customer,
Thankyouforhavingpurchasedandgivenyourpreference
to our product.
The safety precautions and recommendations reported
below are for your own safety and that of others. They
will also provide a means by which to make full use of the
features oered by your appliance.
Please keep this booklet in a safe place. It may be useful
in future, either to yourself or to others in the event that
doubts should arise relating to its operation.
This appliance must be used only for the task it
has explicitly been designed for, that is for cooking
foodstus. Any other form of usage is to be considered
as inappropriate and therefore dangerous.
The manufacturer declines all responsibility in the
event of damage caused by improper, incorrect or
illogical use of the appliance or be faulty installation.
PRODUCT LABEL
This appliance has been designed and constructed in accordance with the following
codes and specications:
AS/NZS 60335.1 General Requirements for Domestic electrical appliances
AS/NSZ 60335.2.6
Particular Requirements for Domestic electrical cooking appliances
AS/NZS CISPR 14.1 Electromagnetic Compatibility Requirements

33
IMPORTANT SAFETY PRECAUTIONSAND RECOMMENDATIONS
IMPORTANT: This appliance is designed and manufactured
solely for the cooking of domestic (household) food and is
not suitable for any non domestic application and therefore
should not be used in a commercial environment.
The appliance guarantee will be void if the appliance is used
within a non domestic environment i.e. a semi commercial,
commercial or communal environment.
Read the instructions carefully before installing and using
the appliance.
■This appliance has been designed and manufactured in
compliance with the applicable standards for the household
cooking products and it fullls all the safety requirements shown
in this manual, including those for surface temperatures.
Some people with sensitive skin may have a more pronounced
temperature perception with some components although these
parts are within the limits allowed by the norms.
Thecompletesafetyof theappliance alsodepends onthe correct
use, we therefore recommend to always pay a extreme attention
while using the product, especially in the presence of children.
■After having unpacked the appliance, check to ensure that it is
not damaged and that the oven door closes correctly.
In case of doubt, do not use it and consult your supplier or a
professionally qualied technician.
■Packing elements (i.e. plastic bags, polystyrene foam, nails,
packing straps, etc.) should not be left around within easy reach
of children, as these may cause serious injuries.
■ Some appliances are supplied with a protective lm on steel and
aluminium parts. This lm must be removed before using the
appliance.
■ IMPORTANT: The use of suitable protective clothing/gloves is
recommended when handling or cleaning this appliance.

44
■Do not attempt to modify the technical characteristics of
the appliance as this may become dangerous to use. The
manufacturer declines all responsibility for any inconvenience
resulting from the inobservance of this condition.
■Do not operate your appliance by means of an external timer or
separate remote-control system.
■Do not carry out cleaning or maintenance operations on the
appliance without having previously disconnected it from the
electric power supply.
■ WARNING: Ensure that the appliance is switched o󰀨 before
replacing the oven lamp to avoid the possibility of electric shock.
■Do not use a steam cleaner because the moisture can get into
the appliance therefore making it unsafe.
■Do not touch the appliance with wet or damp hands (or feet).
■Do not use the appliance whilst in bare feet.
■If you should decide not to use this appliance any longer (or
decide to substitute another model), before disposing of it, it
is recommended that it be made inoperative in an appropriate
manner in accordance to health and environmental protection
regulations, ensuring in particular that all potentially hazardous
parts be made harmless, especially in relation to children who
could play with unused appliances.
■Thevariouscomponentsoftheappliancearerecyclable.Dispose
oftheminaccordancewiththeregulationsinforceinyourcountry.
If the appliance is to be scrapped, remove the power cord.
■ After use, ensure that the knobs/controls are in the o󰀨 position.
■Children less than 8 years of age shall be kept away unless
continuously supervised.
■This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.

55
■The manufacturer declines all liability for injury to persons or
damage to property caused by incorrect or improper use of the
appliance.
■ WARNING: During use the appliance and its accessible parts
become hot; they remain hot for some time after use.
– Care should be taken to avoid touching heating elements
inside the oven.
– The door is hot, use the handle.
– To avoid burns and scalds, young children should be kept
away.
■Make sure that electrical cables connecting other appliances in
the proximity of the oven cannot become entrapped in the oven
door.
■ WARNING: When correctly installed, your product meets all
safety requirements laid down for this type of product category.
However special care should be taken around the rear or the
underneath of the appliance as these areas are not designed or
intended to be touched and may contain sharp or rough edges,
that may cause injury.
■FIRST USE OF THE OVEN - it is advised to follow these
instructions:
– Furnish the interior of the oven as described in the chapter
“CLEANING AND MAINTENANCE”.
– Switch on the empty oven on max to eliminate grease from the
heating elements.
– Disconnect the appliance from the electrical power supply, let
the oven cool down and clean the interior of the oven with a
cloth soaked in water and neutral detergent; then dry carefully.
■ CAUTION: Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can scratch the
surface, which may result in shattering of the glass.
■ Do not line the oven walls or oor with aluminium foil. Do not place
baking trays or the drip tray on the base of the oven chamber.
■ FIRE RISK! Do not store ammable material in the oven.

66
■Always use oven gloves when removing the shelves and food
trays from the oven whilst hot.
■Do not hang towels, dishcloths or other items on the appliance or
its handle – as this could be a re hazard.
■Clean the oven regularly and do not allow fat or oils to build up in
the oven base or tray. Remove spillages as soon as they occur.
■Do not stand on the open oven door.
■Always stand back from the appliance when opening the oven
door to allow steam and hot air to escape before removing the
food.
■ SAFE FOOD HANDLING: Leave food in the oven for as short
a time as possible before and after cooking. This is to avoid
contamination by organisms which may cause food poisoning.
Take particular care during warmer weather.
■ WARNING: Take care NOT to lift the appliance by the door
handle.
■The appliance must not be installed behind a decorative door in
order to avoid overheating.
■ The oven accessories (e.g. oven wire rack) must be tted
correctly as indicated at page 16.
■If the power supply cable is damaged, it must be replaced only
by an authorized service agent in order to avoid a hazard.

77
INSTALLATION
CAUTION:
■This appliance must be installed in accordance with these installation instructions.
■This appliance shall only be serviced by authorised personnel.
■This appliance is to be installed only by an authorised person in compliance
with the current electrical regulations and in observation of the instructions
supplied by the manufacturer.
Failure to comply with this condition will render the guarantee invalid.
■Incorrect installation, for which the manufacturer accepts no responsibility, may
cause personal injury of damage.
■Always disconnect the appliance from mains power supply before carrying out
any maintenance operations or repairs.
■Some appliances are supplied with a protective lm on steel and aluminium
parts. This lm must be removed before using the appliances.
■Important: The use of suitable protective clothing/gloves is recommended when
handling or installing this appliance.
FITTING REQUIREMENTS
■ The oven can be tted in standard units, 60 cm width and depth.
■ Installation requires a compartment as illustrated in gures 1 and 2.
On the lower side, the oven must lay on supports standing the oven weight.
■Remember the housing should not be free standing but be secured to the wall and/or
adjacent ttings.
■We would point out that the adhesive which bonds the plastic laminate to the
furnituremust withstand temperaturesnot less than 150°C to avoiddelamination.
■The walls of the units must be capable of resisting temperatures of 75 °C above
room temperature.
■The walls surrounding the oven must be made of heat-resistant material.
■Do not install the appliance near inammable materials (eg. curtains).
■Do not seal the oven into the cabinetry with silicone or glue; this makes future
servicing di󰀩cult. Elba Appl. AUS Service Agent will not cover the costs of
removing the oven, or of damage caused by this removal.
■The appliance must not be installed behind a decorative door in order to avoid
overheating.
■WARNING: Taking care NOT to lift the oven by the door handle.
WARNING
When correctly installed, your product meets all safety requirements laid down for
this type of product category.
However special care should be taken around the rear or the underneath of the
appliance as these areas are not designed or intended to be touched and may
contain sharp or rough edges, that may cause injury.
IMPORTANT
Some environmental factors and cooking habits can cause condensation in and
around the oven during use. To protect surrounding cabinetry from possible damage
caused by frequent or excessive condensation, we recommend moisture-proong
the oven cavity.

88
595
595
545
22
556
600
550 min
560
600
139,5
520
59,5
583
600
550 min
560
590
Figure 2
Figure 1

99
To ensure internal ventilation, aeration channels must be provided as illustrated in the
gures 2 and 3.
30 mm
600
50 mm
50 550
Figure 3
Figure 4

1010
FIXING THE OVEN
Introduce the oven into the furniture opening and x it with 2 screws (not supplied) as gure 5.
Before xing the 2 screws, check the 2 plastic bushes are correctly in place into the xing
holes (the bushes are already tted on the product and must lie at).
It is essential that the oven rests on a surface which will support its weight, as the screw
xing is only complementary.
Note:
It is essential that when installing your oven adequate air circulation is allowed for within the
installation. See gures 1, 2, 3 and 4.
Inadequate air circulation may greatly impair the performance of your oven and may e󰀨ect
adjacent cabinets due to an increase in temperature.
Caution!
Do not lift this oven by the door handle.
Adjust the hinges of furniture doors adjacent to the oven to allow a 4-5 mm gap between
the furniture door and the oven frame.
IMPORTANT (only for the models NSM 9 ..,
NSM 11 ..): When handling the oven, take
care not to damage the door sensor lever
“L” (g. 6) (near the top left corner of the
oven seal).
LFigure 6
Figure 5

1111
ELECTRICAL REQUIREMENTS
■The appliance must be connected to the mains checking that the voltage corresponds
to the value given in the rating plate and that the electrical cable sections can withstand
the load specied on the plate.
■A suitable isolating switch providing full disconnection from the mains power supply
(under overvoltage category III conditions) is incorporated in the permanent wiring,
mounted and positioned to comply with the local wiring rules and regulations. The
isolating switch must be of an approved type and provide a 3 mm air gap contact
separation in all poles (or in all active [phase] conductors if the local wiring rules allow
for this variation of the requirements).
■The isolating switch shall be easily accessible to the customer with the oven installed.
■If the electrical supply is restricted, means of all-pole disconnection must be accessible
and incorporated in the xed wiring in accordance with the wiring rules.
■The power supply cable must not touch the hot parts and must be positioned so that it
does not exceed 75°C above ambient.
■Theovenissuppliedwithoutapowersupplyplugandthereforeifyouarenotconnecting
directly to the mains, a standardized plug suitable for the load must be tted.
■The plug must be connected to an earthed socket in compliance with safety standards.
■To connect the appliance to the mains electricity supply, do not use adapters, reducers
or branching devices as they can cause overheating and burning.
■Once the appliance has been installed, the switch or socket must always be accessible.
■If the supply cord is damaged it must be replaced by the manufacturer or it’s Service
Agent or a similarly qualied person in order to avoid a hazard.
N.B. The connection of the appliance to earth is mandatory.
If the installation requires alterations to the domestic electrical system call a qualied
electrician. He should also check that the domestic electrical system is suitable for the
power drawn by the appliance.
Replacing the power cord must be done by a qualied electrician in accordance with
the instructions supplied by the manufacturer and in compliance with established
electrical regulations.

1212
REPLACING THE POWER SUPPLY CABLE
Important! This appliance must be connected to the electricity supply only by an
authorised person.
WARNING: If the power supply cable is damaged, it must be replaced only by an
authorised service agent in order to avoid a hazard.
NOTE: The earth conductor must be left about 3 cm longer than the others.
VOLTAGE AND POWER CONSUMPTION
220-240 V ac 2900 W (12.60 A)
FEEDER CABLE SECTION
TYPE H05V2V2-F ( resistance to temperatures of 90°C )
3 x 1,5 mm2(*) (**)
(*) Connection possible with plug and outlet
(**) Connection with wall box connection

1313
ELECTRIC DIAGRAM FOR MODEL NSM 7 NL
Figure 7
1
1a
2
2a
7
7a
6
6a4a
4
3
3a
5
5a
9
9a
L
N
Thermal
overload Oven
cut-o
timer
Oven switch
Oven
thermostat
Oven
fan
motor
Cooling
fan
motor
Oven
heating
elements
Oven
lamp
Line
pilot
lamp
Thermostat
pilot
lamp
Thermal
overload
Earth connection
Bottom
Top
Grill
Circular

1414
ELECTRIC DIAGRAM FOR MODELS NSM 9 XL and NSM 9 NL
Figure 8
Bottom
Top
Grill
Circular
L N
1
1a
2
2a
7
7a
6
6a4a
43
3a
5
5a
9
9a
1 1A
J8 J7 N
470 kΩ
Thermal
overload
Door
switch
Oven switch
Oven
thermostat
Earth connection
Oven
fan
motor Cooling
fan
motor
Oven
heating
elements
Oven
lamp
Thermal
overload
Electronic clock/
programmer

1515
ELECTRIC DIAGRAM FOR MODELS NSM 11 XL and NSM 11 NL
Figure 9
10
10a
2
2a
6
6a4a
4
3
3a
5
5a
11
11a
1 1A
J8 J7 N
L
N
470 kΩ
Thermal
overload
Door
switch
Oven switch
Oven
thermostat
Oven
fan
motor Cooling
fan
motor
Oven
heating
elements
Bottom
Top
Grill
Circular
Oven
lamp
Thermal
overload
Electronic clock/
programmer
Earth connection

1616
USE AND CARE
CAUTION:
■This appliance must be used only for the task it has explicitly been designed for, that
is for domestic cooking of foodstu󰀨s. Any other form of usage is to be considered as
inappropriate and therefore dangerous.
■Do NOT place combustible materials or products on this appliance at any time.
Figure 10bFigure 10a
Click
A
A
Traverso posteriore Arresto di sicurezza
1°
Livelli
2°
3°
4°
5°
6°
7°
Levels
Guard rail Stop notch
USING THE OVEN FOR THE FIRST TIME
OVEN FITTING OUT
Fit the side racks
■Slide the rear prongs of the side rack into the holes “A” at the rear of the oven (g. 10a).
■ Slide the front prong of the side rack into the hole at the front of the oven (g. 10a).
■ Slide in, on the guides, the shelf and the tray (g. 10b).
 The shelf must be tted so that the safety notch, which stops it sliding out, faces the
inside of the oven; the guard rail shall be at the back.
■To dismantle, operate in reverse order.
■NOTE: When using the oven for the rst time, in order to eliminate any traces of
substances or odours left over from the production process, switch the oven on and
run it empty (without the accessories, which should be washed separately), keeping
the installation environment su󰀩ciently ventilated:
• for 60 minutes in the position (thermostat in position 250°C);
• for 30 minutes in the position
(thermostat in position 250°C);
• for 15 minutes in the position (thermostat in position 200°C).
■ Slide o󰀨 the wire racks from the oven walls as in g. 10a;
■ Let the oven cool down, switch o󰀨 the electrical supply, then clean the inside of the
oven with a cloth soaked in water and neutral detergent and dry thoroughly.

1717
Figure 11
GREASE FILTER (OPTIONAL COMPONENT, CAN BE PURCHASED
SEPARATELY)
■ A special screen can be tted at the back of the oven to catch grease particles, mainly
when meat is being roasted.
 Slide in the grease lter on the back of the oven as in g. 11.
■Clean the lter after any cooking!
 The grease lter can be removed for cleaning and should be washed regularly in hot
soapy water.
 Always clean the lter after cooking as any solid residues on it might adversely a󰀨ect
the oven performance.
■ Always dry the lter properly before tting it back into the oven.
CAUTION: When baking pastry etc. this lter should be removed.

1818
Figure 12
Clip Clip
Tab Tab
Left Right
Left Right
TELESCOPIC SLIDING SHELF SUPPORTS
(Models NSM 11 XL and NSM 11 NL only)
The telescopic sliding shelf supports make it safer and easier to insert and remove the
oven shelf and tray.
They stop when they are pulled out to the maximum position.
Important! When tting the sliding shelf supports, make sure that you t:
■ The slides to the top wire of a rack. They do not t on the lower wire.
■The slides so that they run out towards the oven door.
■Both sides of each pair of shelf slides.
■Both sides on the same level.
To x the sliding shelf supports onto the side racks:
■Fit the sliding shelf supports onto the top wire of a rack and press. You will hear a click
as the safety locks clip over the wire.
To remove the telescopic sliding, operate in reverse order.
Cleaning the sliding shelf supports:
■Wipe the supports with a damp cloth and a mild detergent only.
■Do not wash them in the dishwasher, immerse in soapy water, or use oven cleaner
on them.

1919
21
4
65
6 5
1
42
21
3
6 5
CONTROL PANELS
Figure 13b MODEL NSM 9 XL
MODEL NSM 9 NL
Figure 13c
Figure 13a MODEL NSM 7 NL

2020
21
4
65
6 5
1
4
2
Please note: Your appliance has been tted with a cooling fan to achieve optimum
e󰀩ciency of the controls and to ensure lower surface temperatures are maintained.
The cooling fan motor switches ON/OFF depending on temperature.
Depending on cooking temperatures and times, the cooling fan may run on even after
the appliance oven has been switched o󰀨.
The duration of this time is dependent on previous cooking temperature and duration.
Figure 13d MODEL NSM 11 XL
MODEL NSM 11 NL
Figure 13e
CONTROLS DESCRIPTION
1. Oven temperature control knob
2. Function selector control knob
3. Timer (120 minutes cut-o󰀨)
4. Electronic clock/programmer “Touch-control”
5. Oven temperature indicator light
6. Power on indicator light