DelRay DFSP User manual

nCheck local codes and
read all instructions
prior to installation.
nLeavethismanualwith
the owner.
Installation
Operation &
Maintenance
What To Do If You Smell Gas:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
Warning:
Improper installation, adjustment, altera-
tion, ser ice or maintenance can cause
injury or property damage. Refer to this
manual. For assistance or additional in-
formation consult a qualified installer,
ser ice agency or the gas supplier.
For Your Safety:
Do not store or use
gasoline or other flamma-
ble apors and liquids in
the icinity of this or any
other appliance.
Double Burner
Pedestal
Gas Stove
Model DFSP
Questions? Email us at [email protected] or visit our website at www.montigo.com.

Page 2 Part No. XG0509
DFSP Rio Pedestal Stove Quality Gas Products by Montigo
Introduction
About the Rio Pedestal Stove:
Thank you for purchasing the Rio Pedestal Stove, and choosing a
Delray Gas Product. This Rio Sto e features a Double Burner with a
hi-lo adjustable control.
This Rio Sto e is certified for use with Montigo Direct Vent Compo-
nents, and for use with standard 4" B-Vent when using our optional
con ersion kit (part number FSTK03). The Rio Pedestal Sto e is
certified as a heating appliance by CGA and AGA tothe Vented Gas
Fireplace Heater standard (ANSI Z21.88-2000 · CGA 2.33-2000)
and is rated for:
Natural Gas 25,000 BTU/H Maximum Input
18,500 BTU/H Minimum Input
Propane 22,000 BTU/H Maximum Input
17,000 BTU/H Minimum Input
How to use this manual:
This manual co ers all ersions. Sections which are specific to a
particular ersion are marked with a symbol, plus the appropriate
model number.
Warranty and Installation In ormation:
The Montigo warranty will be oided by, and Montigo disclaims any
responsibility for, the following actions:
nModification of the fireplace and/or components including Direct-
Vent assembly or glass doors.
nUse of any component part not manufactured or appro ed by
Montigo in combination with this Delray fireplace system.
nInstallation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation requirements
for factory-built gas fireplaces. Installation & repairs should be done by
a qualified contractor.
Installations in Canada must conform to the current CAN/CGA B-
149.1 and .2 Gas Installation Code and local regulations. If the optional
air-circulating fan kit is installed, it must be electrically grounded in
accordance with CSA C22.1 Canadian Electrical Code Part 1 and/or
Local Codes.
Installations in the USA must conform to local codes, or in the
absense of local codes to the National Fuel Gas Code, ANSI Z223.1-
1988. If the optional air-circulating fan is installed, it must be grounded
in accordance with local codes or, in the absence of local codes, with
the National Electrical Code, ANSI/NFPA 70-1987.
Table Of Contents
Introduction............................................................................. 2
Installation
Choosing a Location ...................................................... 3
Installing the Gasline ...................................................... 4
Direct Vent Installation ................................................... 4
General Requirements ...................................... 4
Terminations ..................................................... 4
Rear Vent Installations....................................5-6
Top Vent Through-the-Wall Installations ............ 7
Top Vent Through-the-Roof Installations ........... 8
B-Vent Installation ........................................................ 10
Remo ing and Installing the Door ................................ 11
Installing the Logset ..................................................... 11
Wiring ....................................................................... 12
Operation ..........................................................................13-15
Maintenance .....................................................................15-16
Warranty ................................................................................. 17
Appendix
A. Accessories and Vent Components .................. 18 - 19
B. Termination Locations ............................................. 20
CAUTIONS
Due to its high operating temperatures, the appliance
should be located out of traffic & away from furniture and
draperies.
nChildren and adults should be alerted to the hazards of
the high surface temperature, which could cause burns
or clothing ignition.
nYoung children should be carefully super ised when
they are in the same room as the appliance.
nClothing or other flammable materials should not be
placed on or near the appliance.

Page 3
Part No. XG0509
DFSP Rio Pedestal Stove
Quality Gas Products by Montigo
Choosing a Location
The fireplace may be installed in any location that maintains clearances
to air conditioning ducts, electrical wiring and plumbing. Safety, as well
as efficiency of operation, must be considered when selecting the
fireplace location. Try to select a location that does not interfere with
room traffic, has adequate entilation, and offers an accessible
pathway for ent installation. Refer to page 4 - Vent Installation for
more information.
The Rio's dimensions are shown below:
Installation
Figure 1. Stove dimensions.
24
16
34 1/2
10 7/8
Front View
Side View
6 1/2
32 5/8
17 5/8
21 3/49
25
Ø4"
Ø7" When installing this sto e in an alco e, the minimum clearance from
the top of the sto e to a combustible surface is 42". (Minimum 1"
clearance must be maintained around the vent pipes.)
D
C
A
B
B
Figure 3. Clearances to combustible surfaces.
Clearances
The Rio Pedestal Stove's clearances to combustible materials are:
A - Back 1 ½"
B - Side 10 ½"
C-Floor 0"
D-Top* 42"
* Clearance from the top of the sto e to a
combustible ceiling.

Page 4 Part No. XG0509
DFSP Rio Pedestal Stove Quality Gas Products by Montigo
Direct Vent Installation
This section co ers the installation of enting and terminations.
Installation Requirements
nRio Sto es are certified for use with Montigo Standard Series (4"
/ 7") enting components and appro ed Vent Kits (listed below)
nMinimum 1" clearance to combustibles required for ent pipes
nUse only certified Montigo vent components. (Use of other parts will oid the
Montigo warranty, and may impede the operation of the sto e.)
nAll joints must be secured with a minimum of two screws per joint
nVent terminations must not be recessed in walls or siding
nHorizontal runs must be supported by a minimum of two supports
per horizontal run. A minimum of one screw on each side of
support is also required
nFlex ent sections may be stretched up to 50% of their total length
(eg. a 24" section may be stretched to 36")
nMaximum horizontal run for a flex section with no ertical rise is 3 feet.
nFlex ent sections o er 3 feet must fall within the limits set by the enting
graph and must ha e a minimum ertical rise of 3 inches per foot of flex.
nVenting components can be used in any combination of solid/rigid
nSolid ent sections may be cut less than half way from the tapered end
nVenting components can be used in any combination of solid/rigid pipe or
flex pipe and in any orientation (Male connectors can face in any direction)
Vent Terminations
Selecting A Termination Location
Choosing your ent termination location will help to determine whether you need to
use a top ent or rear ent fireplace. Figure 5, below, shows typical fireplace
locations and the enting options they pro ide.
For a more detailed diagram of allowed termination locations, see
ppendix B.
Installing The Gas Line
The gas line must be installed before completing the installation.
Natural Gas requires a minimum inlet gas supply pressure of 5.5"
W.C. & a manifold pressure of 3.5" W.C. Propane Gas requires a
minimum inlet gas supply pressure of 11" W.C. & a manifold pressure
of 10" W.C. Pro ision must also be made for a 1/8" N.P.T. plugged
tapping and be accessible for test gauge connection immediately
upstream of the gas supply controls to the appliance. The sto e is
supplied with a flexible gas connector which is factory installed. The
gas al e is located behind the pedestal base, and is accessible from
the back or by remo ing the control panel co er plate. It should be
attached to the gas line with an appro ed fitting, as required by the
applicable installation codes.
Installation
Figure 5. Fireplace locations and vent terminations.
Note: After gas line is connected, each appliance connection,
valve and valve train must be checked while under
normal operating pressure with either a liquid solution, or
leak detection de ice, to locate any source of leak. Tighten
any areas where bubbling appears or leak is detected until
bubbling stops completely or leak is no longer detected.
DO NOT use a lame o any kind to test or leaks.
During any pressure testing of the gas supply piping that excedes 1/2
psig (3.5 kPa), the appliance and its indi idual shutoff al e must be
disconnected from gas supply system.
When pressure testing the gas supply piping system at test pressures
of less than or equal to 1/2 psig (3.5 kPa), the appliance must be
isolated from the gas supply piping system by closing its indi idual
manual shutoff al e.
Figure 4. Gas line access.
Cautions:Cautions:
Cautions:Cautions:
Cautions:
nVent terminations can be ery hot. If the termination is less than
7 feet abo e a public walkway, it should be fitted with a certified
Montigo Heat Guard. (Part no. MTKOG)
nDo not obstruct, or attempt to conceal, the ent termination.
These actions will affect the operation of the fireplace, and may
be hazardous.
nIn hea y snow areas, take extra care to pre ent snow buildup
from obstructing the ent termination.
Direct Vent

Page 5
Part No. XG0509
DFSP Rio Pedestal Stove
Quality Gas Products by Montigo
Installation Direct Vent
Installing Terminations with Built-In Frames
1. Frame the termination opening to 10" x 10".
2. Fasten the termination to the studs using a minimum of 4 screws.
Installing Rio 'Snorkel' Terminations
See Rear Vent Venting Runs section for Snorkel Installations.
1. Ensure that the two long mounting brackets are facing the
bottom of the termination. (See inset). This will pro ide more
heat protection at the top of the termination, where temperatures
are highest.
2. Attach to the faceplate of the termination using four sheet metal
screws.
Installing Heat Guards over Terminations
MTKOG
Rear Vent Venting Runs
The Rio Pedestal Stove may be ented directly out the back through
an exterior wall. This application allows the sto e to be installed with
no isible enting in the room. You must use the Direct Vent - Rear
Vent Kit (Part # FSTK01) for this installation.
Rear Vent Installation Requirements.
nThe height from the hearth to the center of the ent pipe is 25".
nThe maximum horizontal run for a Rear Vent installation is 14".
nThe FST-11 (18" length section is supplied for connecting the sto e
to the termination. The FST-11 may be cut to required length, and
must not exceed 14".
nThe two wall plates and the co er plate included with this kit must
be installed for proper operation.
Figure 6. Rear Vent installation, showing the required components and
the height of the stove's flue collar.
Installation.
1. Mark an 11" x 11" hole centred exactly 25" from the centre of the
sto e's flue collar to the hearth (- the surface the sto e will be sitting
directly on). This hole will be cut right through to the exterior of the
building for the ent pipe to pass through. Precise location of this
hole is ery important: check your measurements be ore
cutting!
2. Connect the FST11 to the back of the sto e, but do not fasten it.
Slide the co er plate and the inner wall plate onto the FST11, with
their open edges down.
Place the sto e on its hearth, and slide it back until the FST11 pipe
protrudes through the hole in the wall and the sto e is in the
desired position. (See figure 7).
Figure 7. Installiing the inner wall plate and cover plate.
MTO-3
25"

Page 6 Part No. XG0509
DFSP Rio Pedestal Stove Quality Gas Products by Montigo
Slide the inner wall plate back against the wall. Le el the plate,
making sure it completely co ers the opening in the wall, and fasten
it in place using four wood screws. (Note that the heat shield
connected to the plate is not concentric -- its top edge should sit
close to the inside top edge of the 11" x 11" hole.)
Slide the Co er Plate onto the inner wall plate and fasten it with one
black sheet metal screw on each side.
3. The (outer) wall plate is used to mount the snorkel-type termination
to the building exterior. Position the wall plate o er the 11 " x 11"
hole.
Push the heat shield portion into the opening so that it mates with
the heat shield on the inner wall plate. This will properly position the
wall plate o er the opening. (Refer to figure 8).
Le el the wall plate. It may be installed either o er top of the
exterior cladding (brick, stucco, siding, etc.), or against the exterior
sheathing. If installing it directly on the exterior sheathing, you must
cut away the siding or other fascia by tracing an outline around the
wall plate.
4. Slide the sto e forward and remo e the FST11 pipe. Attach the
FST11 to the snorkel termination, and mount the assembly on the
outer wall plate between the two alignment tabs as shown in figure
9. Fasten it in place with at least two screws at the top and two at
the bottom.
Figure 8. Installing the outer wall plate.
5. Install the rain shield onto the top of the outer wall plate as shown in
figure 10. Run beads of caulking, also shown in figure 10.
6. If necessary, cut the FST11 pipe to the required length, and then
slide the sto e back into position and connect it to the FST11. Refer
to figure 11.
Figure 9. ttaching the snorkel termination to the outer wall plate.
Figure 11. Mating the stove to the FST11 and snorkel termination.
Snorkel
FST11
Figure 10. Installing the rain shield and applying silicone sealant.
Caulk here
Caulk here
(both sides)
Rain shield
Installation Direct Vent

Page 7
Part No. XG0509
DFSP Rio Pedestal Stove
Quality Gas Products by Montigo
Installation Direct Vent
Top Vent Venting Runs
For the Rio Pedestal Sto e there are two types of Top Vent (DV)
installations: A) Horizontal (Through-The-Wall) Installations and B)
Vertical (Through-The-Roof) Installations.
Allowable Vent Runs
Before you install any enting, you must determine whether the enting
run will be acceptable. Unacceptable enting can affect the fireplace's
combustion. Figure 12 shows arious ent rises and the corresponding
number of 90° bends which can be made.
A) Through-the-Wall (Horizontal) Venting Option
The horizontal enting option requires an FSTK02 Vent Kit. Figure 13
shows the components which are used to attain different ent heights.
Additional sto e pipe or Montigo Standard Series ent components
may be used to increase the ent run, as long as the run still falls within
the limits set out in Figure 12.
1 - Vertical Rise is measured
from the center of the sto e's
flue collar to the center of the
termination.
2 - A - Top Vent Con ersion Box
(FST04)
B - Std. Sto e Pipe (FST11)
C - 90° Elbow (MEL9MB)
D - O ersize Sto e Pipe
(FST05)
E - Standard Termination
(MTO-3)
Installing the Stove Pipe
1. Ensure that the intended pathway for the enting is clear.Try to
position the sto e midway between two studs to a oid ha ing to cut
them. Cut and frame a 10" x 10" hole for the termination.
2. Attach the top ent con ersion box (Part # FST04) to the sto e's
flue collar as shown in Figure 14. Secure it with four sheet metal
screws.
Stove pipe
sections
Figure 14. ttaching the top vent conversion box.  Installing the
sto e pipe.

3. Cut the flex pipe (Part # FST08) to length and install the second
flex collar. Install the flex liner onto the inner collar of the con ersion
box.
Figure 13. Possible venting configurations using the FSTK02 kit.
Figure 12. Venting limitations for top vent installations.
Vertical Rise 24 - 34"
Vertical Rise 33 - 56"
Vertical Rise 55 - 77"
H2
V
H1
B
B
BB
E
E
E
B
B
B
B
D
D
C
C
C
A
The minimum ertical rise for a Top Vent Installation is 2', which
allows 1 - 90° elbow and a maximum horizontal run of 10'. With
greater ertical rise, the number of 90° bends may be increased
according to the chart below. The total maximum horizontal run
(HT) is also shown, and the run between each elbow (Hx) may be
any length, as long as it does not exceed (HT).
Vent Rise1Max. # Max. Horiz.
(V) of elbows Run (HT)
2' (min.) 1 10'
4' 2 10'
5' 2 10'
10' 3 10'
15' 3 10'
20' 3 10'
25' (max.) See vertical vent section
1 Vertical rise is measured from the center of the sto e's
flue collar to the center of the termination.
2 See 'Through-the-Roof Installations'
Example:
If V= 12', the ent run may use up to 3 - 90° elbows.
If H1= 3', H2=2', and H3=3',
then HT=8'.
This would be an acceptable installation.
FST04
Conversion box
4”Inner Elbow

Page 8 Part No. XG0509
DFSP Rio Pedestal Stove Quality Gas Products by Montigo
4. Install the first sto e pipe onto the con ersion box by sliding it o er
the flex pipe (refer to Figure 14). Install a spacer spring around the
flex liner. Secure the pipe with at least two ½" hex screws spaced
approx. 3/4" from the joint. Slide the remaining ertical sto e pipes
into place, without fastening them. Install a spacer spring inside
each sto e pipe section.
5. Cut the horizontal sto e pipe (FST11) to length. Slide it and the
90°elbow o er the flex and onto the ertical pieces of sto e pipe.
Install the last spacer spring inside the horizontal section. Slide the
Decorati e Wall Plate (Part # FST07) onto the horizontal section,
making sure the unpainted side faces the wall.
Completing the Vent Run
6. Slide the sto e back into position so the pipe protrudes through the
wall. Pull the flex forward and attach it to the termination (or other
ent sections, if necessary, to extend the ent run) with high temp
sealant. Run a bead of high temp sealant around the sto e pipe
and push the termination on. Attach the MTO-3 termination to the
wall as shown on page 5.
Adjust the position of the sto e pipes so thethat joints are all equally
spaced. Ensure that there is at least 1 1/2" o erlap between each
section.
Secure each sto e pipe joint with at least three ½" hex screws
spaced approx. 3/4" from the joint (so that the brass ring will co er
both the joint and the screws).
Finishing
7. Now slide the Decorati e Wall Plate against the hole, le el it, and
secure using four screws.
8. Co er each joint in the sto e pipes with a brass decorator ring. The
rings should co er the joint as well as the sheet metal screws.
Attach the ring using the black 3/8" screws pro ided. Make sure the
screw is facing the back of the sto e. See Figure 15.
Installation Direct Vent
FRBV005
Figure 15. Installing the decorative brass rings. Figure 16. Vertical installation options. Left: straight vertical installation
(no offsets).
B) Vertical (Through-The-Roo ) Venting Option
When enting through the roof, use an FSTK04 Vent Kit. Additional
sto e pipe or Montigo Standard Series ent components may be used
to increase the ent run, as long as the run still falls within the limits set
out in Figure 16.
Vertical Vent Requirements:
Vertical terminations (Part # MVTK-1) must be installed:
• minimum 2' abo e the highest point where the ent passes
through the roof
• minimum 6' from a mechanical air inlet
• minimum 18" from a parapet wall
Maximum ent height is 25 abo e the sto e's flue collar.
(Note: Flame characteristics may change if the maximum ent height is
used.)
A maximum of two offsets (each o set has two 90° bends) may be
made. The total length of the offset(s) must not be more than 25% of
the ertical ent height, when measured from center to center of the
piping.
Example: Vertical ent height - 20 feet
25% of 20' = 5' max. offset allowed
2 - 2' offsets required = 4' offset
This vent configuration is acceptable.
25’
max.
Firestop
Support
ring
Ceiling
box
MEXT
sections
MVTK-1
MEXT-2
MVA
Stove pipes
2’min.
MFL (flex)
sections
2' min.
25’
max.
Firestop
Support
ring
Ceiling
box
MEXT
sections
MVTK-1
MEXT-2
Stove pipes
FSTRO1

Page 9
Part No. XG0509
DFSP Rio Pedestal Stove
Quality Gas Products by Montigo
Direct Vent
Installation
8. Mo e the sto e into position below the sto e pipe. Slide the bottom
section of sto e pipe down o er the collar on the top ent
con ersion box. Install a spacer spring inside this section.
9. Slide the last section of sto e pipe down o er the bottom pipe.
Adjust the position of the sto e pipes so thethat joints are all equally
spaced. Ensure that there is at least 1 1/2" o erlap between each
section.
10. Secure each sto e pipe joint with at least three ½" hex screws
spaced approx. 3/4" from the joint (so that the brass ring will co er
both the joint and the screws).
11. Finishing
Install the ceiling collar o er the ceiling box to pro ide a finished look.
Co er each joint in the sto e pipes with a brass decorator ring. The
rings should co er the joint as well as the sheet metal screws.
Attach the ring using the black 3/8" screws pro ided. Make sure the
screw is facing the back of the sto e. See Figure 15.
12. Completing the Vent Run
Run additional components as necessary to bring the enting up
through the roof, and install the ertical termination.
Figure 18. Installing spacer springs.  Installing the slip section.


Installing the Stove Pipe
1. Ensure that the intended pathway for the enting is clear.Try to
position the sto e midway between two joists to a oid ha ing to cut
them. Cut and frame a 11" x 11" hole in the ceiling and roof as
required.
2. Install the ceiling box as shown in Figure 17. Ensure that there is at
least 2" clearance from the bottom of the box to the ceiling. Fasten
in place with 2 screws per side.
3. Slide the MEXT-2 down into position so the male end protrudes into
the room below the ceiling box as shown in Figure 17 and secure it
temporarily with an MSPXT-7 support plate and ring.
11”
Ceiling box
MEXT-2
in position
11”
support ring
support plate
ceiling plate
COLL011
Figure 17. Installing the ceiling box.
4. Measure the flex pipe (Part # FST08) and cut it to the required
length. Install the second collar onto the end of the flex. Attach one
end of the flex to the inner collar of the MEXT-2, and secure it with
three screws.
5. Slide the decorati e ceiling plate about two inches down from the
end of the top section of sto e pipe. Install the top sto e pipe onto
the outer collar of the MEXT-2. Now slide the decorati eceiling
plate up against the bottom of the ceiling box and secure it with four
screws. Install the first spacer spring by sliding it up o er the flex
and into the bottom of the sto e pipe.
6. Now slide the slip section (Part # FST05) up o er the flex,
o erlapping the top section at least half its length to keep the pipe
out of your way. Install a spacer spring inside the slip section. Slide
the last section of standard sto e pipe up inside the slip section,
again o erlapping the two by at least half a pipe length.
7. Attach the top ent con ersion box (Part # FST04) to the sto e's
flue collar as shown in Figure 18. Secure it with four sheet metal
screws. Figure 19. Positioning and fastening the sto e pipes.
Slide slip
section down
Ensure all
3 sections are
evenly spaced.
Direct Vent

Page 10 Part No. XG0509
DFSP Rio Pedestal Stove Quality Gas Products by Montigo
Installation B-Vent
B-Vent Installation
This Rio Stove is certified for use with standard B-Vent, when
installed using Montigo's optional B-Vent Conversion Kit (part #
FSTK-03), and pro ided the following steps are carefully followed.
Sto e Pipe, Liner, and B-Vent are not included with the kit. Refer to
Step 5.
When ented with standard 4" B-Vent, the B-Vent is installed directly
onto the draft hood assembly. Co ering the B- ent with sto e pipe is
optional for this installation. When ented using 4" flex liner, the flex
must be co ered with sto e pipe.
Refer to the current CAN/CGA B-149.1 and .2 or ANSI Z223.1-1988
Gas Installation Code for B-Vent installation regulations.
4"
Draft hood assembly
Figure 21. Location of the flue
collar on the draft hood, for
determining the location of
the ceiling opening.
1. There are four relief pots on the back of the sto e body. For B-Vent
Installations only, these pots must be remo ed to pro ide adequate
combustion air. (See Figure 20.)
2. Check to ensure that the path for enting is clear. Try to position
the sto e midway between two joists to a oid ha ing to cut them.
Cut and frame an opening centered o er the ent collar on the
draft hood (see Figure 21).
3. Attach the draft hood assembly to the back of the sto e and secure
with four sheet metal screws as shown in Figure 22.
Figure 20. Removing the relief
pots on B-Vent
Installations.
4. Caution: This sto e is shipped ready for direct ent installation. For
B-Vent installations, the ollowing wiring change must be
made.
nGently pull the spill switch wires from the bottom of the draft
hood, and splice them into the On/Off switch circuit. The switch
should be wired in series as shown in Figure 23.
5. Montigo offers a complete range of sto e pipe and flex liner for
completing the installation. A ailable components are listed in
Appendix B - Venting Components:
Refer to the installation instructions supplied with the FSTK03 for more
information. When using other brands of sto e pipe or liner, refer to the
ent manufacturer's installation instructions.
nTest your B-Vent installation after completion to ensure that
no combustible by-products are spilling from the draft hood
opening. This draft test should be performed after a fifteen
(15) minute warm up period. The manufacturer will not be
responsible for any installations with inadequate draw.
CAUTION:
Figure 23. Wiring the draft hood spill switch into the millivolt circuit.
Spill switch
Burner 'On/Off'
switch
To gas valve 'TH'
connections
Splice here
Figure 22. ttaching the draft hood assembly and the first B-Vent
section.
Draft hood assembly
4" B-Vent

Page 11
Part No. XG0509
DFSP Rio Pedestal Stove
Quality Gas Products by Montigo
Installation
Removing and Installing
the Door
Removing the decorative door cover:
The door co er is held in place by two clips at the top, and two pins on
the botton. Locate the latch shown in figure 24 and pull down. While
holding the latch down, pull the co er out at the bottom and then
downward until the clips at the top are clear. (See figure 24.)
Removing the door:
Remo e the 8 nuts around the edge of the glass door, and then pull
the door outwards and upwards until it is clear of the door rail.(See
Figure 25). Ensure that a good seal is maintained when re-installing the
door.
Figure 24. Removing or installing the door cover.
Figure 25. Removing or installing the glass door.
Latch
Pin
Clips
2. Unpack the logs. Be sure to handle the logs carefully, as they are
ery fragile.
3. Place the Back log onto the back log rest as shown below in figure
26. The log has lip on the bottom which fits into the slot on the log
rest.
4. Place the Front log onto the front log rest as shown in figure 26.
Center the log from side to side, and push it against the back of
the log rest. Carefully push the log onto the metal spikes on the
log rest.
5. Place the top logs in position as shown in figures 27 and 28.
6. Start the fireplace. If the flame appears satisfactory, replace the
glass door and door co er.
Figure 26. Positioning for the top logs ('C' and 'D' ).
Installing the Log Set
Installing the Logs:
The double burner Rio Stove is supplied with six (6) fibre logs.
Unpack the logs and handle them ery carefully.
1. Remo e the door co er and the glass door.
Back log
Left log Right log
Front log
Center logs
Figure 27. Proper placement (top view).
Back log
Front log rest
Back log rest
Heat exchanger tubes
Front log
Front burner tube
Back burner tube Ember tray

Page 12 Part No. XG0509
DFSP Rio Pedestal Stove Quality Gas Products by Montigo
Installation
Wiring or the optional Blower Kit
The Rio Steel Sto e may be equipped with an optional ariable
speed blower kit (Part #RFK1080) for circulating additional heat
into the li ing space.
Installations in Canada which employ the blower kit must be
electrically grounded in accordance with CSA C22.1 Canadian
Electrical Code Part 1 and/or Local Codes.
Installations in the USA which employ the blower kit must be
grounded in accordance with local codes or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70-1987.
For more information see the Installation Guide included with the
blower kit.
Figure 30a. Wiring for optional air circulating blower kit.
NOTE: If any of the original wire supplied with the appliance is replaced, it
must be replaced with the same type, or its equi alent.
Figure 30b. Wiring schematic for optional blower kit.
1
Optional Fan Switch
Motor
Speed Control
15/1/60 Supply
GL1L2
Back log
Left log Right log
Front log
Center logs
Figure 28. Log placement as seen from the front of the stove.
NOTES:
n If the logs are not placed properly, excessive sooting will result.
nThe surface of the logs will crack due to the heat from the
flames. This is a normal occurance.
Gas Control and Pilot Wiring or optional Intermittent
Pilot (-I models) Ignition
Figure 29. Wiring for the Rio Stove with Honeywell gas control and
pilot.
Honeywell (Q3450)
Pilot Assembly
Pilot Electrical
Harness Connector
Honeywell Gas
Control (SV9501M)
Gas Control
Connector Fuse
Limit
Switch Wall
Switch
Fan Plug
Receptacle
Junction Box
Junction Box Cover
White
Black
Green
40 VA
Transformer
115VAC
24VAC
Grnd Screw
Wiring

Page 13
Part No. XG0509
DFSP Rio Pedestal Stove
Quality Gas Products by Montigo
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
nIf you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control knob.
Ne er use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified ser ice technician. Force
or attempt to repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified ser ice technician to inspect the
appliance and to replace any part of the control system, and
any gas control which has been under water.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
hea ier than air and will settle on the floor.
What To Do I You Smell Gas:
nDo not try to light any appliance.
nDo not touch any electrical switch; do not use any phone
in your building.
nImmediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
To Turn Off Gas To Appliance:
Operation - Continuous Pilot Models
3. Push in gas control knob slightly and turn clockwise
to "Off". Do not force.
4. Flip up lower trim.
1. Turn off remote switch.
2. Flip down lower trim.
1. STOP! Read the safety information abo e on this label.
2. Flip down lower brass trims.
3. Push in gas control knob and turn clockwise to "OFF."
4. Wait fi e (5) minutes to clear out any gas. Smell for gas,
including near the floor. If you then smell gas, STOP! Follow
"B" in the safety information abo e on this label. If you don't
smell gas, go to the next step.
5. Locate pilot burner (See illustration at right.) and follow
steps below.
6. Turn knob on gas control counterclockwise to
"PILOT."
7. Push in gas control knob completely and hold. Light with
Piezo Igniter button. Continue to hold the control knob in for
about (1) minute after the pilot is lit. Release the knob and it
will pop back up. Pilot should remain lit. If it goes out repeat
steps 3 through 8.
nIf knob does not pop up when released. Stop and
immediately call your ser ice technician or gas supplier.
nIf the pilot will not stay lit after
se eral tries, turn the gas
control knob to "OFF" and
call your ser ice technician
or gas supplier.
8. Push in gas control knob and
turn counterclockwise to "ON."
9. Flip up lower brass trim.
10.Turn on remote switch to ignite fire.
Lighting Instructions:
For Your Safety - READ BEFORE LIGHTING:
NOTE: Knob cannot be turned from "PILOT" to
"OFF" unless knob is pushed in slightly.
Do not force.
Gas control
knob shown in
'On' Position
On
Flame ControlBurner Control
Off Pilot
Hi Lo

Page 14 Part No. XG0509
DFSP Rio Pedestal Stove Quality Gas Products by Montigo
For Your Safety - READ BEFORE LIGHTING:
To Turn Off Gas To Appliance:
Lighting Instructions:
nIf you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control knob.
Ne er use tools. If the knob will not push in or turn by
hand, don't try to repair it, call a qualified ser ice technician.
Force or attempt to repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified ser ice technician to inspect the
appliance and to replace any part of the control system, and
any gas control which has been under water.
A. This appliance is equipped with an ignition system that
lights the pilot burner automatically. Do not attempt to
light the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
hea ier than air and will settle on the floor.
What To Do I You Smell Gas:
nDo not try to light any appliance.
nDo not touch any electrical switch; do not use any phone
in your building.
nImmediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
1. Turn off remote switch.
2. Flip down lower trim.
3. Turn the switch on the gas control to "Off".
4. Flip up lower trim.
1. STOP! Read the safety information abo e on this label.
2. Flip down lower brass trims.
3. Turn switch on the gas control to OFF".
4. Wait 5 minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information abo e on this
label. If you don't smell gas, go to the next step.
5. Turn switch on the gas control to "ON". NOTE: This unit is
equipped with an ignition system that lights the pilot burner
automatically. Do not attempt to light the pilot by hand.
6. Turn on wall switch.
7. Flip up lower brass trim.
8. If the fireplace does not operate, follow the instructions "To
Turn Off Gas To Appliance" and call your ser ice technician
or gas supplier.
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
Operation - Intermittent Pilot (-I) Models
Gas
Inlet
Gas Control Switch
Shown in "On"Position

Page 15
Part No. XG0509
DFSP Rio Pedestal Stove
Quality Gas Products by Montigo
Maintenance
CAUTIONS
nFireplace gas control must be in the “OFF” position and pilot
and main burners extinguished when cleaning appliance with
a acuum.
nDoors and logs can get ery hot. Handle only when cool.
General
nHa e the fireplace installation inspected yearly, including a
isual check of the ent system, the burner and the pilot flame.
For your con enience a 1/8" manifold pressure tap is supplied
on the gas al e for a test gauge connection. See Figure 28.
nFor Natural Gas this appliance requires a minimum inlet
pressure of 5.5" W.C. and a manifold pressure of 3.5" W.C.
nFor Propane Gas this appliance requires a minimum inlet
pressure of 11" W.C. and a manifold pressure of 10" W.C.
nAlways keep the fireplace area clear and free of combustible
materials, as well as gasoline and other flammable apours and
liquids.
nDo not use this appliance if any part has been under water.
Immediately call a qualified ser ice technician to inspect the
appliance and to replace any part of the control system and any
gas control which has been under water.
Operation
Lighting Instructions
See pages 13 and 14.
Cleaning
When the fireplace is first acti ated, there may be some smoking and a
isible film may be left on the glass. This is a normal condition, and is
the result of burning of protecti e coatings on new metal.
nGlass must be cleaned periodically to remo e any film (which is a
normal biproduct of combustion) which may be isible. Film can
easily be remo ed by remo ing the door, as shown on page 11.
Handle the door carefully, and clean it with non-abrasi e glass
cleaners. One of the most effecti e products is Kel Kem.
nSilicone seals on inner door during initial firing will "off gas", lea ing
a isual deposit of a white substance on combustion chamber walls.
This can easily be remo ed using normal household products.
nUse a acuum cleaner or whisk broom to keep the control
compartment, burner, and firebox free from dust and lint.
nLogs may be cleaned periodically with a acuum to remo e soot or
other contaminates. The logs are fragile and will break easily.
Adjusting the Burner
Raising or lowering the Flame Height
Rio Sto es are equipped with an adjustable burner, allowing you to
raise or lower the flames. To adjust the flames, locate the black knob
marked 'Flame Control', in the centre of thecontrol panel (See Figure
31).
nTo raise the flame height, turn the black knob marked 'Flame
Control' counterclockwise.
nTo lower the flame height, turn clockwise.
Figure 31. Hi-Lo' djustment on the Rio Stove's gas valve.
WARNING:
Do not attempt to clean glass when hot.
Do not clean glass with abrasi e materials as any glass
etching may cause premature glass failure.

Page 16 Part No. XG0509
DFSP Rio Pedestal Stove Quality Gas Products by Montigo
Maintenance
Troubleshooting
If your fireplace still does not operate correctly, consult your dealer or
the manufacturer.
All service and repairs should be per ormed by a quali ied
agency.
All spare parts, optional fans (see optional fan instruction guide), and
optional trim finishes are a ailable from the manufacturer or your local
dealer.
HO EYWELL SV 9500 /SV9600
Troubleshooting Sequence
N TE: Before Troubleshooting, Familiarize Yourself With
The Startup And Checkout Procedure.
· Turn Gas Supply off
· Set thermostat to
call for heat
SV9500/SV9600
is powered
(24 V C nominal)
O
O
O
O
O
YES
YES
YES
YES
YES
YES
YES
O
O
O
START
Igniter warms up
and glows red.
Pilot Valve opens.
Turn gas on.
Pilot Burner lights?
Main Valve opens?
SYSTEM OK
Unplug Pilot Burner Cable,
Measure Voltage at
SV9500/SV9600 HSI
Terminals (24 V C
Nominal, See INSET)
Replace Igniter/
Flame Rod ssembly.
Replace Igniter/
Flame Rod ssembly.
Replace SV9500/SV9600
Measure Voltage to SV9500
/SV9600. Voltage must
be at least 19.5 V C
Discard old Igniter/
Flame Rod ssembly.
Replace Igniter/Flame
Rod ssembly and retain.
Restart Troubleshooting
Sequence. Does main
valve open?
Replace
SV9500/
SV9600
Check
Transformer
Line Volt
Supply
Replace
SV9500/
SV9600.
Save old
Igniter/Flame
Rod ssembly
for service.
I SET
HSI
Terminals
CHECK:
· Line voltage power
· Low voltage transformer
· Limit Controller
· Thermostat
· Wiring
· ir proving switch on
combustion air blower system
· Vent damper (if used) is open
and end switch made
Gas Control Valve
Figure 32. Honeywell VS8520 gas valve.
Pilot Burner Adjustment
1. Locate Pilot Adjustment Screw. (See figure 32.)
2. Adjust pilot screw to pro ide properly sized flame as shown in
figure 33).
3. After installing or ser icing, leak test with a soap solution with main
burner on. Coat pipe and tubing joints, gasket etc. with soap
solution. Bubbles indicate leaks. Tighten any areas where the
bubbles appear until the bubbling stops completely.
Figure 33. Pilot Burner
Troubleshooting
The following is a troubleshooting chart of possible problems:
PROBLEM CORRECTIVE ACTION
Noisy Pilot Flame Locate pilot adjustement screw on gas
control al e. Flame is decreased by
turning adjustment screw clockwise.
Pilot won’t ignite Disconnect remote wires and try to
light pilot. If pilot now works, remote
connections are faulty. Check wiring
diagram figure 32.
Main burner will 1. Check wiring (see figure 32).
not light 2. Check wall switch for proper
connection.
TH
On/Off Switch
Power Generator
TP TH-TP

Page 17
Part No. XG0509
DFSP Rio Pedestal Stove
Quality Gas Products by Montigo
Warranty
The WarrantyThe Warranty
The WarrantyThe Warranty
The Warranty
The Companies warrants the DelRay Gas Appliance to be free from defects in materials and workmanship at the time of manufacture. On the DelRay, there is a ten-year
warranty on the firebox and its components, a fi e-year warranty on the main burner, and a one-year warranty on the gas control al e, pilot burner and fibre logs. Glass,
plated/painted finishes, and refractory lining are exempt.
Remedy And Exclusions
The co erage of this Warranty is limited to all components of the Gas Appliance manufactured by The Companies.
This Warranty only co ers DelRay Gas Appliances installed in the United States or Canada.
If the components of the Gas Appliance co ered by this Warranty are found to be defecti e within the time frame stated (see The Companies right of in estigation outlined
below). The Companies will, at its option, replace or repair defecti e components of the Gas Appliance manufactured by The Companies at no charge, and will also pay
for reasonable labour costs incurred in replacing or repairing components. If repair or replacement is not commercially practical, The Companies will, at its option, refund
the purchase price of the DelRay Gas Appliance.
This Warranty co ers only parts and labour as pro ided abo e. In no case shall The Companies be responsible for materials, components, or construction which are not
manufactured or supplied by The Companies, or for the labour necessary to install, repair or remo e such materials, components or construction. All replacement or repair
components will be shipped F.O.B. the nearest The Companies factory.
Qualifications To The WarrantyQualifications To The Warranty
Qualifications To The WarrantyQualifications To The Warranty
Qualifications To The Warranty
The Gas Appliance Warranty outlined abo e is further subject to the following qualifications:
(1) The Gas Appliance must be installed in accordance with The Companies installation instructions and local building codes. The Warranty on this DelRay Gas Appliance
co ers only the component parts manufactured by The Companies. The use of components manufactured by others with this DelRay Gas Appliance could create
serious safety hazards, may result in the denial of certification by recognized national safety agencies, and could be in iolation of local building codes. This warranty
does not co er any damages occurring from the use of any components not manufactured or supplied by The Companies
(2) The DelRay Gas Appliance must be subjected to normal use. The Gas Appliances are designed to burn gas only. Burning con entional fireplace fuels such as wood,
coal or any other solid fuel will cause damage to the Gas Appliance, will produce excessi e temperatures and will result in a fire hazard.
Limitations On LiabilityLimitations On Liability
Limitations On LiabilityLimitations On Liability
Limitations On Liability
It is expressly agreed and understood that The Companies sole obligation, and purchaser's exclusi e remedy under this Warranty, under any other warranty, expressed
or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified abo e.
In no e ent shall The Companies be responsible for any incidental or consequential damages caused by defects in its products, whether such damage occurs or is disco ered
before or after replacement or repair, and whether or not such damage is caused by The Companies negligence. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the abo e limitation or exclusion may not apply to you. The duration of any implied warranty with respect to this DelRay Gas Appliance
is limited to the duration of the foregoing warranty. Some states do not allow limitation on how long an implied warranty lasts, so the abo e may not apply to you.
Investigation Of Claims Against WarrantyInvestigation Of Claims Against Warranty
Investigation Of Claims Against WarrantyInvestigation Of Claims Against Warranty
Investigation Of Claims Against Warranty
The Companies reser es the right to in estigate any and all claims against this Warranty and to decide upon method of settlement.
The Companies Are Not Responsible For Work Done Without Written Consent
The Companies shall in no e ent be responsible for any warranty work done without first obtaining The Companies written consent.
Dealers Ha e No Authority To Alter This Warranty
The Companies employees and dealers ha e no authority to make any warranties nor to authorize any remedies in addition to or inconsistent with those stated abo e.
How THow T
How THow T
How To Register A Claim Against Wo Register A Claim Against W
o Register A Claim Against Wo Register A Claim Against W
o Register A Claim Against Warrantyarranty
arrantyarranty
arranty
In order for any claim under this Warranty to be alid, The Companies must be notified of the claimed defect in writing or by telephone, as soon as reasonably possible
after the defect is disco ered. Claims against this Warranty in writing should include the date of installation, and a description of the defect.
Other RightsOther Rights
Other RightsOther Rights
Other Rights
This Warranty gi es you specific legal rights, and you may also ha e other rights which ary from state to state.
NOTE: The Companies as stated abo e refer to - Canadian Heating Products Inc. and/or Montigo Del Ray Corp.
Canadian Heating Products Inc. and/or Montigo DelRay Corp. reserves the right to make changes at any time,
without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.

Page 18 Part No. XG0509
DFSP Rio Pedestal Stove Quality Gas Products by Montigo
Appendix A - Accessories and Vent Components
Accessories
Item Description Quantity Order Code
1 Wireless Remote Control 1 RX-10
2 Milli olt Thermostat Programmable 1
3 Milli olt Thermostat Non-programmable 1
4 Variable Speed Blower Kit Includes heat sensor, ariable speed control. 1 RFK1080
Vent Kits
Item Description Quantity Part #
Direct Vent - Rear Vent Kit FSTK01
5 Snorkel Termination, Freestanding 1
6 Outer wall plate 1
7 Inner wall plate 1
8 Co er plate 1
9 FST11 18" Vent Pipe, Black (std. female/female) 1
10 Co er Plate for Sto e ent collar, & screws 1
11 Self Tapping 1/2" screws 12
12 Wood Screws 4
13 Touch-up Paint, Black 1 can
14 Rain Shield 1
Direct Vent - Through the Wall Kit FSTK02
15 Top Vent `Con ersion Box' 1
16 Black Sto e Pipe (std. female/female) 3
17 Black Slip Section (o ersize female/female) 1
18 Black 90o Elbow (male/male) 1
19 Brass Decorator Ring 4
20 Screw, Phillips, Black (1 per brass ring) 4
21 Decorati e Wall/Ceiling Plate 1
22 Flex Venting (4" dia.) incl. 1 flex ent collar 1x6"
23 Flex Vent Collar (field installed) 1
24 Pipe Joint Compound 1
25 Touch-up Paint, Black 1 can
26 Spacer Springs 3
27 1 1/4" Drywall Screws 4
28 Self Tapping 1/2" Screws 24
29 Termination 1
B-Vent Kit FSTK03
30 Draft Hood Assembly, Painted(std. female dia.) 1
Direct Vent - Through the Roo Kit FSTK04
31 Top Vent ‘Con ersion Box’ 1
32 Black Sto e Pipe (std. female/female) 2
33 Black Slip Section(o ersize female/female) 1
34 Brass Decorator Ring 3
35 Screw, 3/8" Phillips, Black (one per brass ring) 3
36 Ceiling Box 1
37 Flex Venting (4" dia.) - includes 1 flex ent collar1 x 4'
38 Flex Vent Collar (field installed) 1
39 Pipe joint compound 1
40 Touch-up Paint, Black 1
41 Spacer Springs 3
Vent Components - Avail. Individually
Item Quantity Part #
Black Sto e Pipe - 24" (std. female/female) 1 FST05
Black Sto e Pipe - 18" (std. female/female) 1 FST11
Black Slip Section - 24" (o ersize female/female) 1 FST06
Black 90o Elbow (male/male) 1 MEL9MB
Brass Decorator Ring 1 FSTR01
Decorati e Wall Plate 1 FST07
Black Decorati e Ceiling Box 1 FST10
Top Vent `Con ersion Box' 1 FST04
Flex Venting (4" dia.) incl. 1 flex ent collar 1x6" FST08
Flex Vent Collar (field installed) 1 FST09
Spacer Springs 3 SPS
Black Phillips Screws 6 RHW2045
Black Self-Tapping Screws 24 RHW2099
Pipe Joint Compound 1 RIN2004
Touch-up Paint, Black 1 can PAINT01
Touch-up Paint, Charcoal Grey 1 can PAINT02
For available Standard Series (4/7") Vent Components,
re er to our current price list.

Page 19
Part No. XG0509
DFSP Rio Pedestal Stove
Quality Gas Products by Montigo
Appendix A - Accessories and Vent Components
Direct Vent - Rear Vent Kit FSTK01
B-Vent Kit FSTK03
Direct Vent - Through-the-Wall Kit FSTK02
Direct Vent - Through-the-Roo Kit FSTK04
21
29
26
28
25 24
16
18
16
17 16
22
23
15
19
30
5
6
78 9
10
13
11
14 36
32
34
41
35
33 32
37
38
31
40 39

Page 20 Part No. XG0509
DFSP Rio Pedestal Stove Quality Gas Products by Montigo
Appendix B - Termination Locations
A = clearance to the termination frame abo e grade, eranda, porch, deck, or
balcony [16 inches (41 cm) minimum]
B = clearance to door, or sides and top of window, that may be opened [16
inches (41 cm) minimum for appliances ≤100 000 BTU/H (30kW)]
C = clearance to bottom of window that may be opened horizontally [36 inches
(92 cm) minimum for appliances ≤100 000 BTU/H (30kW)]
D = no clearance to permanently closed window when installed with appro ed
glass penetration termination
E = clearance to permanently closed window [16 inches 41 cm recommended
to pre ent condensation on window]
F = ertical clearance to entilated soffit located abo e the termination within a
horizontal distance of 2 feet (61 cm) from the centreline of the termination [22
inches (56 cm) minimum]
G = clearance to un entilated soffit
[16inches (41 cm) minimum to non-combustibles]
[22 inches (56 cm) minimum to combustibles]
H = clearance to outside corner [9 inches (23 cm) minimum]
I = clearance to inside corner [12 inches (31 cm) minimum]
J = * not to be installed abo e a meter/regulator assembly within
40" (103 cm) horizontally from the centreline of the regulator
K = clearance to ser ice regulator ent outlet [3 feet minimum in the United
States] [*6 feet (1.8 m) minimum in Canada]
L = clearance to nonmechanical air supply inlet to building or the combustion air
inlet to any other appliance [16 inches (41 cm) minimum for appliances
≤100 000 BTU/H (30kW)]
M = clearance to mechanical air supply inlet
[*6 feet (1.8 m) minimum]
N =† clearance abo e pa ed sidewalk or a pa ed dri eway located on
public property [*7 feet (2.1 m) minimum]
P = clearance under eranda, porch, deck, or balcony
[16 inches (41 cm) minimum‡ to non-combustibles]
[22 inches (56 cm) minimum‡ to combustibles]
Q = clearance abo e a roof [24 inches (61 cm) minimum]
R = clearance to adjacent walls and neighbouring buildings
[18 inches (46 cm) minimum]
S = clearance from corner in recessed location
[12 inches (31 cm) minimum]
T = maximum depth in recessed location
[48 inches (122 cm) minimum]
U = minimum width for back wall of recessed location
[24 inches (61 cm) minimum]
V = no horizontal clearance between the frames of two terminations that are
le el.
W = horizontal clearance between the frames of two terminations that are not
le el. [36 inches (92 cm) minimum]
†a ent shall not terminate directly abo e a sidewalk or pa ed dri eway
which is located between two single family dwellings and ser es both
dwellings
‡only permitted if eranda, porch, deck, or balcony has an open side that
is equal to or greater than the depth of the enclosed area
*as specified in CGA B149 Installation Codes. Note: local Codes or
Regulations may require different clearances