Delta-Opti VM-215 User manual

Manufactured in China for:
DELTA-OPTI Monika Matysiak,
60-713 Poznan, 10 Graniczna St., Poland
www.shopdelta.eu
User Manual
VM-215, VM-2701,
VM-802M, VM-101M,
VM-236M VM-24

Table Of Contents
EMC COMPLIANCE T
IMPORTANT PRECAUTIONS ------------------------------------------------2
1. Introduction
1.1. General ------------------------------------------------------------------------------4
1.2. Features -----------------------------------------------------------------------------4
1.3. Packing List ------------------------------------------------------------------------4
2. Installation
2.1. Connection of signal cable-------------------------------------------------------5
2.2. Connection of power cord--------------------------------------------------------5
2.3. Connection of Audio cable-------------------------------------------------------5
2.4. Power on----------------------------------------------------------------------------6
2.5. Self-inspection---------------------------------------------------------------------6
2.6. Image Adjustment-----------------------------------------------------------------6
3. Operation
3.1. OSD button----------------------------------------------------------------------- 7
3.2. OSD menu and operation menu introduction ---------------------------------8
3.3. Safeguard -------------------------------------------------------------------------12
3.4. Setting of display mode --------------------------------------------------------12
4. Technical specification
4.1 ALLTFT-LCD monitor specification -----------------------------------------13
4.2 Pin assignment of signal cable-------------------------------------------------14
4.3 Visual Inspection----------------------------------------------------------------- M
5. Trouble Shooting------------------------------------------------------------ 15
6. Operation Warranty ------------------------------------------------------- 16

EMC COMPLIANCE IMPORTANT PRECAUTIONS
page 1 page 2
EMC COMPLIANCE
This device has been tested and found to comply with the standards for a class B
digital device, pursuant to Part 15 of FCC Rules. Those standards are designed to
provide reasonable protection against harmful interference in a residential installation.
This device generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
If this device does cause harmful interference to radio or television reception, which
can be determined by turning the device off and on, user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
—Increase the separation between the device and receiver
・—Plug the device into a wall outlet different from that connected to the receiver.
…Consult the dealer or an experienced radio/TV technician for help.
CAUTION: any change or modification not expressly illustrated in this manual
may void the warranty.
NOTE: any unshielded cable is not allowed to be used in the device!
IMPORTANT PRECAUTIONS
A WARNINGS:
1. Before using this device, please read all the instructions in this manual carefully.
2. Please keep the manual carefully for future reference.
3. Unplug this device from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp or wet cloth to clean. Please use LCD screen detergent
for cleaning if it is still dirty.
4. Do not use the parts not recommended by the manufacturer, otherwise it may cause
a hazard.
5. When unplugging the power cord of the monitor or adapter, please hold the plug
with your hand, do not pull the cord directly.
6. Do not place any object on the power cord. Do not trample it either.
7. Do not use the device near water sources, e.g. bathtub, basin, kitchen sink, or
washing machine. Do not place the device on a wet floor, or near a swimming pool
etc. Do not touch the screen with your fingers or other hard objects.
8. Slots and openings on the housing and its back or bottom are provided for
ventilation, lb ensure reliable operation of the components and to protect them from
overheating, these openings must not be blocked or covered placing the device on a
bed, sofa, rug, or other similar surface. The device should never be placed near or over
a radiator or heater and should not be placed in a built-in installation unless proper
ventilation is provided.
9. Make sure that the device is at least 5cm distance from the wall or other objects
around when it is in use.
10. The power supply must respond to that stated on the rating plate. If you have any
query about the power supply, please refer to the dealer or local power supply
provider.
11. As a safeguard measure, the monitor or adapter is equipped with a power cord
with three-terminal plug, the third terminal is grounded. If the plug cannot be inserted
into the outlet, please contact an electrical technician for replacing the original outlet
while keeping the safeguard measure in effect.
12. Ensure that the power socket and cord in use are able to take the sum of the rated
currency of all the products.
13. Do not put the device at the place where user is subject to mal-operation.
14. Observe all the warnings and instructions described in the manual.
15. Do not overload the power outlet or use any extension cord, otherwise it may
cause fire or electric shock.
16. Do not attempt to repair this device yourself since opening or removing covers
may expose you to dangerous voltage or other hazards. Refer servicing to qualified
A

IMPORTANT PRECAUTIONS INTRODUCTION
page 3 page 4
service personnel.
17. Unplug this monitor or AC adaptor from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or worn.
b. If the device has been dropped or its housing has been damaged.
c. When the performance of the device deteriorates distinctly.
18. The power cord is the main facility to turn on/off the device; unplug it if the
device is not used for a long period of time.
19. Store the device at a place of good ventilation; avoid strong sunlight, high
temperature or humidity.
20. Store the device at a place at ・20°C~55°C room temperature. Otherwise, it may
cause permanent damage.
1. Introduction
1.1 General
Thank you for purchasing the latest model of LCD monitor, with advantages of high
display performance and light weight etc, meanwhile with the power saving and no-
radiation features, the latest LCD will bring you comfortable, safe and environmental-
protection brand-new visual experience.
Your purchase and use of this product is highly appreciated!
1.2 Features
•" High performance intelligent multi-frequency scanning, use active matrix Thin film
transistor liquid crystal display (TFT).
---Micro Computer digital technology control, no radiation, no glare 旧uilt-in
multimedia speaker system (option).
—Built-in AV signal connection terminal and 8 terminal (option).
…Comply with VESA DPMS International Power Saving Regulation.
・・・ Support DDC 1/2B and Windows PNP Plug & Play.
■■- Microprocessor based with OSD (On Screen Display) control, be able to adjust
the image to optimum.
—Built-in hoisting hole complying with International Standard(VESA), which is able
to hang the display on the wall.
1.3 Packing list
Please make sure the following items are included with your LCD display before
installation:
一A LCD monitor (with pedestal)
一A VGA signal cable, DVI-D signal cable (option)
An audio cable
—A power cord cable
―User's manual
If any of there items are missing, please contact with your dealer for technical
support and customer service.
NOTE: be sure to save original box and all packing material for transport in
future if the display need.
A

INSTALLATION INSTALLATION
page 5 page 6
2.4 Power on
Turn on the monitor and computer, and then indicator will light green (or blue) when the screen is under normal condition. Please check
to see if there is any wrong with the connection of video signal cable if the indicator lights red.
2.5 Self-inspection
If the monitor inspects there is no horizontal and vertical signal, it will prompt to check the video input, please refer to the illustration
below, and the monitor will enter into power saving mode after several seconds, the indicator will light red. The screen will restore to
normal display once receiving video signal.
2.6 Image Adjustment
Please adjust the image according to your need; please refer to the "Operation" in Section Three.
HDMI signal input: connect to computer HDMI signal output jack VGA signal input: connect to computer VGA signal output jack Audio
input: connect to computer sound card audio output jack Power jack: connect to input jack
2.1 Connection of signal cable
Before connecting your monitor and
PC with signal cable, please turn off your monitor and computer. And then insert one
end of the signal cable into the VGA or HDMI jack on your computer, and lock it with
two fixed screw for ensured grounding. Finally, please insert another end of signal
cable to the VGA or HDMI signal input jack of monitor and lock it with fixed screw.
2.2 Connection of power cord
First, insert one end of power cord cable into the power input jack of monitor, and
another end into power outlet.
2.3 Connection of Audio cable
Please insert one end of audio cable into the sound card audio output terminal on your
computer, another end into the audio input terminal of monitor.
3. Operation I
3.1 OSD one
(1) Power Switch( O )
Digital control light-touch switch, used for turning on or off monitor power.
(2) Power Indicator
When the monitor is under normal working condition, the indicator will light green (or
blue); if the monitor is under saving mode, the indicator will light red or off. And the
indicator will turn off under the power off mode. (When the power indicator turns off, it
means that the monitor is under off mode,please disconnect the power cable when the
monitor is not used for the purpose of safety.)
2. Installation I
—
V_______________________________________________________________________ 丿
O 0
•1
1
HDMI
__________________________ _ VGA "
E NO SIGNAL
Power

OPERATION OPERATION
page 7 page 8
(3) AUTO Button
Auto adjust / exit
(4) 一Button
Select and adjust the OSD items (Decrease the value)
(5) Menu Button
Activate OSD, enter sub menu, select items, confirm selection.
(6) + Button
Select and adjust the OSD items (Increase the value)
MENU Adjustment Setting :
1. Press Menu into Main Function choice Menu
2. Press + or - to switch the image of Main Function changing settings.
3. Press Menu to switch to submenu changing setting and To Press + or - into this
menu.
With + or - to select the desired items, and then press the MENU button for adjustment,
with + or - button to adjust the display items to optimum, press again for confirmation
and exit adjustment.
Color adjust menu
Brightness: use + or - to adjust the brightness to optimum.
Contrast: use + or - to adjust the contrast to optimum.. Exit:
back to previous menu.
1. Press + or - to adjust the setting.
2. Press AUTO to return back Main Menu. Picture adjustment menu
3.11 OSD menu and operation menu introduction
Press the MENU to call out the OSD menu (main menu), please see the
illustration as below:
H-position adjustment: use + or - to adjust the horizontal position to optimum. V-
position adjustment: use + or - to adjust the vertical position to optimum. Phase
adjustment: use + or - to adjust the focus and definition to optimum. Clock
adjustment: use + or - to adjust the clock image display to track stability.
Sharpness: 1 2 3 4 5 6
Exit: back to previous menu.
1440*90
0
60Hz
Colour
Function
OSD Menu
Misc
Exit
Sharpness
Exit

OPERATION OPERATION
page 9 page 10
Function:
Auto Adjust
Auto Colour
Exit
OSD Tool Adjustment Menu :
OSD H-position adjustment: use + or - to adjust the Horizontal position.
OSD V-position adjustment: use + or -to adjust the Vertical position.
OSD Timer:
Mode select
Reset
Volum
Exit
Exit: exit OSD menu
4:3 16:9
YES NO
Exit
ON
OFF
Exit: back to previous menu.
MISC.:

OPERATION OPERATION
page 11 page 12
3.2 OSD two (option)
3.1 Power on-off switch
This key is digital control, working by slightly touch, used for turn on or turn off the display
power supply.
3.2 Indicator light
When monitor is working normally , the indicator light looks green (or blue), when the
monitor is under electricity saving, the indicator light looks red or extinct, when power off,
the indicator light will extinct, but the adapter still under the power-on condition, in view of
safety, should cut off the adapter power supply.
3.3 Function keys
3.3.1 AUTO/SELECT key
When with only VGA mode: without OSD menu, this key is used to auto-adjust, to adjust
the geometrical setting to best condition. Under OSD menu, this key is use asconfirmation.
Under VGA+DVI mode, this key is used to switch the signal between VGA and DVL
3.3.2 +/-or t>/< key
Under OSD menu, these two keys are used for scan and select menu from left or right,
meanwhile adjust the volume. When under without menu condition, if the monitor either
without audio signal, -/< Can used as shortcut key of brightness;
if the monitor with audio signal function, +/- or >/< only used for adjusting volume.
3.3.3 MENU key
Menu key , used for enter into menu and exit from menu.
3.4 OSD menu
3.4.1 main menu
Item: 1. Color adjusting; 2. Picture adjusting; 3. Auto-adjusting; 4. Item adjusting;
5. Others; 6. Exit
3.4.2.submenu
Item: 1 .brightness 2.contract ratio 3.auto image adjustment 4.auto color adjustment 5.color temp
6.red 7.green 8.blue 9.Aspect ratio 10.H-position 11.V- position 12.clock 13.phase
14.language 15.Menu H- position 16.Menu V-position 17.OSD timer 18.reset
I m PICTURE
Mor Teop.
T.................
IHI SI2EaPOSITIOH
I 6 SETUP
I ❶INFCMATION

TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION
page 13 page 14
display information of the monitor
Auto Adjustment
Text
Game
Internet
Sport
DCR
The monitor will be shown out of range if
the monitor exceed the max resolution
switch the display model
main menu
submenu
function
picture
brightness
adjust the brightness of the monitor
contract ratio
adjust the contract ratio of the monitor
auto image adjustment
Auto adjust the position of the picture
auto color adjustment
Auto adjust the color of the picture
color
color temp
Choose the color temp., users can set the color
temperature by themselves
red
User can adjust this when set the color temp
green
blue
size and position
Aspect ratio
switch aspect ratio of the picture
H-position
adjust the horizontal position of the picture
V- position
adjust the vertical position of the picture
clock
adjust the picture's time and pulse
phase
adjust the phase of the pictures
Setup
language
adjust OSD language
Menu H- position
adjust up and down of the OSD menu
Menu V-position
adjust size of the OSD menu
OSD timer
The time disappeared after completion
reset
reset all functions of the monitor
information
display information of the monitor

TROUBLESHOOTING Warranty Guide
page 15 page 16
3.3 Safeguard
When the video signal of your computer exceeds the frequency range of monitor (refer to product
specification), the micro-computer of monitor will turn off the sync
product specification
signal of horizontal and vertical for the purpose of monitor protection, please refer
to the illustration below. The monitor will enter saving mode after few seconds,
and the power indicator will light red. Please
set the output frequency of your computer within the acceptable range of
monitor so that
OUT OF
RANGE
the monitor can work normally.
3.4 Setting of display mode
With standard VESA and DDC function, the monitor will scan frequency, output power,
performance etc and transfer to PC after turning on when you use the video card with VESA
DDC1/2B function. And it will identify the connection mode of display and select the proper
resolution.
The preset mode before leaving factory is as below:
Mode I Resolution I Horizontal(KHz) Vertical(Hz)
1
640x400
31.469
70.087
2
640x480
31.469
59.940
3
640x480
37.861
72.809
4
640x480
37.500
75.000
5
720x400
31.469
70.087
6
800x600
35.156
56.250
7
800x600
37.879
60.317
8
800x600
48.077
72.188
9
800x600
46.875
75.000
10
1024x768
48.363
60.004
11
1024x768
56.476
70.069
12
1024x768
58.038
71.918
13
1024x768
60.023
75.029
14
1024x768
48.019
60.000
15
1024x768
47.700
60.000
16
1152x864
67.500
75.000
17
1280x800
49.702
74.900
18
1280x800
62.795
60.000
19
1360x768
47.700
60.000
20
1280X1024
47. 700
60. 000
21
1440X900
55.000
60. 000
22
1600X900
60. 000
60. 000
23
1680X1050
62. 000
60. 000
24
1920X1080
65.000
60. 000
products size
15.6,6:09
17.0H04:03
19.0w04:03
19.0〃16:10
22ff 16:10
display style
Active matrix T
FT
display size
469.9mm
431.8mm
482.6mm
482.6mm
558.8mm
pixel pitch
0.255*0.255mm
0,2640264mm
0.29r0.294mm
0.285'0.285mm
0.282*0.282mm
Horizontal Viewing angle
160
160
160
160
160
Vertical Viewing angle
150
150
150
150
150
max brightness
250cd/m?
400cd/m?
300cd/rrf
300cd/m?
450cd/m2
dynamic contrast ratio
5000:1
5000:1
8000:1
8000:1
10000:1
response time
8ms
5ms
5ms
5ms
5ms
standard resolution
1366*768
1280M024
1280*1024
1440*900
1680*1050
video input
RGB Analog 15 pin D-sub or DVI-D(option)
signal input
H/V TTL, analog 0.7Vpp+singal /75 Q
Horizontal frequency
64.000KHZ
64.000KHZ
64.000KHZ
55.935KHZ
65.100KHZ
Vertical frequency
60.0Hz
60.0Hz
60.0Hz
59.8Hz
60.0Hz
H-size of picture
344.2mm
341.9mm
380.2mm
410.4mm
473.8mm
V- size of picture
193.5mm
274.4mm
305.0mm
260.5mm
300.1mm
power supply
AC100-240V, 50/60HZ, 1.5A
working environmental
temperature
5°0-40°0
storage environmental
temperature
-20°C-60力
Operation relative humidity
10%-85%
power consumption
25W
28.5W
29.5W
32.5W
34.8W
standby power
consumption
1W
0.63W
0.67W
0.68W
0.70W
weight) N.W.)
2.8Kg
3.5Kg
3.8Kg
4.0Kg
5.0Kg
weight( G.W.)
3.5Kg
4.6Kg
5.0Kg
5.2Kg
6.5Kg
Packing dimension
(L*H*W I
420*110*397
436*138*431
460*145*478
488*370*125
570*433*128
safety standard
GB4943-2001
Energy Efficiency Grade
grade 2
grade 2
grade 2
grade 3