Delta T27T867 User manual

84893 Rev. D
MultiChoice®Valve Trim with Diverter
Installation Instructions
Owners Manual
T27T859, T27T867, T27T897,
T27T959, T27T967 and
T27T997 Series
Write purchased model number here.
T
E
F
L
O
N
You May Need
Table of Contents:
Warranties ................................................................................. Page 2
Installation Instructions ............................................................. Pages 3 - 6
Clean and care........................................................................... Page 7
Maintenance .............................................................................. Page 7
Cartridge Summary Reference Sheet ....................................... Page 7
Replacement Parts .................................................................... Page 9 - 12
To order replacement parts, visit www.deltafaucet.com
CAUTION: This system/device must be set by the
installer to ensure safe, maximum temperature.
Any change in the setting may raise the discharge
temperature above the limit considered safe and
may lead to hot water burns.
NOTICE TO INSTALLER: CAUTION!–As the
installer of this valve, it is your responsibility
to properly INSTALL and ADJUST this valve
per the instructions given. This valve does
not automatically adjust for inlet temperature
changes, therefore, someone must make the
necessary temperature knob adjustments
at
the time of installation and further adjustments
may be necessary due to seasonal water
temperature change. YOU MUST inform the
owner/user of this requirement by following the
instructions. If you or the owner/user are unsure
how to properly make these adjustments please
refer to page 5 and if still uncertain, call us at
1-800-345-DELTA.
After installation and adjustment, you must afx
your name, company name and the date you
adjusted the temperature knob to the caution
label provided and apply or attach the label to
the back side of the closest cabinet door and
the warning label to the water heater. Leave
this Instruction Sheet for the owner’s/user’s
reference. WARNING: This pressure balanced
or thermostatic bath valve is designed
to minimize the effects of outlet water
temperature changes due to inlet pressure
changes, commonly caused by dishwashers,
washing machines, toilets and the like. It may
not provide protection from hot water burns
when there is a failure of other temperature
controlling devices elsewhere in the plumbing
system, if the temperature knob is not properly
set or if the hot water temperature is changed
after the settings are made or if the water inlet
changes due to seasonal changes. WARNING:
Do not install a shut-off device on either outlet
of this valve. When this type of device shuts
off the water ow, it can defeat the ability of
the valve to balance the hot and cold water
pressures.
10/19/16 1
T27T Series T27T Series 84893
T27T Series

84893 Rev. D 2
Parts and Finish
All parts (other than electronic parts and batteries) and finishes of this Delta®faucet are warranted to the original consumer
purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the
home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
Electronic Parts and Batteries (if applicable)
Electronic parts (other than batteries), if any, of this Delta®faucet are warranted to the original consumer purchaser to be free
from defects in material and workmanship for 5 years from the date of purchase or, for commercial users, for one year from
the date of purchase. No warranty is provided on batteries.
Delta Faucet Company will replace, FREE OF CHARGE, during the applicable warranty period, any part or finish that proves
defective in material and/or workmanship under normal installation, use and service. If repair or replacement is not practical,
Delta Faucet Company may elect to refund the purchase price in exchange for the return of the product. These are your
exclusive remedies.
Delta Faucet Company recommends using a professional plumber for all installation and repair. We also recommend that you
use only genuine Delta®replacement parts.
Delta Faucet Company shall not be liable for any damage to the faucet resulting from misuse, abuse, neglect or improper or
incorrectly performed installation, maintenance or repair, including failure to follow the applicable care and cleaning instruc-
tions.
Replacement parts may be obtained by calling the applicable number below or by writing to:
In the United States and Mexico: In Canada:
Delta Faucet Company Masco Canada Limited, Plumbing Group
Product Service Technical Service Centre
55 E. 111th Street 350 South Edgeware Road
Indianapolis, IN 46280 St. Thomas, Ontario, Canada N5P 4L1
1-877-345-DELTA (3358) 1-877-345-DELTA (3358)
[email protected] [email protected]
Proof of purchase (original sales receipt) from the original purchaser must be made available to Delta Faucet Company for all
warranty claims unless the purchaser has registered the product with Brizo Kitchen & Bath Company. This warranty applies
only to Delta® faucets manufactured after January 1, 1995 and installed in the United States of America, Canada and Mexico.
DELTA FAUCET COMPANY SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
(INCLUDING LABOR CHARGES) FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THE FAUCET. Some
states/provinces do not allow the exclusion or limitation of special, incidental or consequential damages, so these limitations
and exclusions may not apply to you. This warranty gives you special legal rights. You may also have other rights which vary
from state/province to state/province.
This is Delta Faucet Company’s exclusive written warranty and the warranty is not transferable.
If you have any questions or concerns regarding our warranty, please view our Warranty FAQs at www.deltafaucet.com, email us at
[email protected] or call us at the applicable number above.
Lifetime Faucet and Finish Limited Warranty
© 2016 Masco Corporation of Indiana

84893 Rev. D
Installation
1Cartridge Installation
A. B.
Turn off water supplies. Remove cover (1),
bonnet nuts (2) and test caps (3) from the
rough-in body (4).
Place a bucket or small container over the front
of the valve body and slowly open the water
supplies to ush any debris from the supply
lines before installing the cartridge. Turn the
water supplies back off.
Rotate the valve cartridge (1) so that “H” (2) is
on the hot side and the “C” (2) is on the cold
side. Add silicone lube to the three o-rings (3)
shown above to make the cartridge easier to
install and remove from the valve body. Insert
cartridge into valve body as shown. Ensure the
keys on the body are fully engaged with the
slots in the body (4) A light coating of plumbers
grease applied to o-rings may aid in assembly..
Thread bonnet nut (2) onto cartridge. Hand
tighten securely. Slide o-ring (1) over the
cartridge and bonnet.
For the exceptions of back to back or reverse
installations (hot on right and cold on left) only:
Rotate valve cartridge (1) so “H” is on the hot side
and “C” is on the cold side and the word “UP” (2)
appears on the bottom. Apply silicone lube to the
three o-rings shown above to make the cartridge
easier to install and remove from the rough-in
body.
Install the cartridge making sure that the keys are
fully engaged with the slot in the rough-in body (see
step B). Slide o-ring (3) and bonnet nut (4) over
the cartridge and thread onto the rough-in body.
Hand tighten securely.
3
C.
Back to back Installation
Cold
Hot
Normal Installation
(changes not required)
Reverse
Installation
1
2
3
2
4
3
14
4
2
4
1
2
3
1
3
2

84893 Rev. D
Installation
2Diverter Cartridge Installation
4
Diverter Bonnet Installation
Slide bonnet nut (1) over diverter sleeve (2) and
thread into rough-in body.
Hand tighten securely.
B.
For Diverter Cartridge Installation:
Apply silicone lube to the o-ring (2) to make
the diverter sleeve (3) easier to install diverter
cartridge.
Rotate the diverter cartridge (1) so the pin is at
the bottom for proper installation.
Apply silicone lube to the o-rings (4) to make
the diverter sleeve (3) easier to install diverter
cartridge.
Align diverter sleeve so that the notches are in
the same position as the notches on rough-in
body (5).
A.
3
1
5
2
1
2
5
4

84893 Rev. D
Installation
3Trim Installation
5
Escutcheon Installation
For nished walls up to 1 1/8". Install trim sleeve
(1) over valve cartridge (7) and bonnet. Secure
backplate (2) to rough-in body using 4 screws (3)
provided.
Note: Be sure backplate is oriented front side
forward and markings are visible.
Holding escutcheon (5) in place, thread trim nut (4)
onto diverter sleeve (6).
Note: For thick wall installations, order
installation kit RP90544 to support finished
wall thickness up to 2 1/8".
On rough or uneven surfaces it is necessary
to apply caulk around the backplate (2) to
supplement the seal. Do not caulk the drip notch
in the bottom of the backplate (2). Do not caulk
the escutcheon (5).
Volume Handle Installation
Install valve handle (1) over cartridge (4), screw in
set screw (2) using a allen wrench.
Place set screw cover (3) over set screw and apply
pressure until cover is properly seated.
A. B.
12
3
4
4
5
C.
4
3
Adjust temperature limit stop
Turn on water supplies; LET THE WATER RUN AT
BOTH FULL HOT AND FULL COLD TO ENSURE
THE WATER IS RUNNING AS HOT/COLD AS
POSSIBLE. Place a thermometer in a plastic tumbler,
and hold the tumbler in the water stream. Place the
temperature knob (1) onto the splines (2), then rotate
the temperature knob counter-clockwise until you
achieve your maximum desired temperature from the
outlet (not more than 120° or the lower temperature
mandated by your local plumbing code).
If max temperature is not achieved before limit
stop (3) on temperature knob (1) meets the limit
stop (4) on the volume control handle. Remove
the temperature control knob (1) from splines (2).
Rotate temperature control knob (1) clockwise.
Place temperature control knob (1) back onto splines
(2) and continue to rotate counter-clockwise until
maximum desired temperature is achieved.Remove
the temperature knob (1) and replace onto thesplines
(2), making sure that the temperature knob limit stop
(3) hits against the volume handle limit stop (4) as
shown.
1
24
3
Installation and Adjustment of the Temperature Knob
Failure to do so may cause injury.
6
2
1
3
3
7