DentalEZ StarDental Titan-E User manual

866.DTE.INFO (383.4636)
www.DentalEZ.com
0344
StarDental®
1816 Colonial Village Lane
Lancaster, PA 17601 U.S.A.
Printed in the U.S.A.
©2019 DentalEZ, Inc.
Emergo Europe
Prinsessegracht 20
2514 AP The Hague
The Netherlands
EC REP
StarDental® Instruments
Caution: Federal law restricts this device to
sale by or on the order of a dentist.
065810 E Date of Issue 2019-05-24
Titan®-E Low-Speed
Handpiece Motor
Instruction Manual
Non-Sterile
Medical Device
Contents
Specications
20,000 rpm Motor: StarDental®Part #266131 (Fixed Back End Part #266132)
 •NoLubricationRequired
 •RecommendedAirPressure:40-45psi(swivelmotor)
 •AirFlow:2.1SCFM@40-45psiatMaximumPowerPoint(swivelmotor)
 •Rotation:ForwardandReverse
 •4-LineConnection(FixedBackEnd)
Installation
1. Selectthemotorappropriatefortubingbasedonpowerrequirements.Examineconnection
ofthemotorandswiveltubingcongurationasthesemustmatchcongurationofdelivery
systemtubing.
DriveAir Water
Exhaust
Air Air
4-Line Tubing 2/3-Line Tubing
Drive
Air
Water
•Specications
•Installation
•Operation
•Cleaning&Sterilization
•Troubleshooting
•ReplacementPartNumbers
•Warranty
Sterilizableupto135°C
135°C
Titan E
20,000 rpm - Lube Free
Made in the U.S.A.
JXXXXX
®
StarDental
®
20KMotor
(StarDental Part #266131) Swivel
BEFORE OPERATING THE MOTOR, CAREFULLY READ AND FOLLOW ALL OF THESE INSTRUCTIONS. SAVE
THESE INSTRUCTIONS FOR FUTURE REFERENCE AND OBSERVE ALL WARNINGS AND CAUTIONS.
Indications For Use
Usedintraorallybytraineddentalprofessionalsfordrillingandpreparationofdentalcavities
forrestoration,suchasllings.Theintendeduseextendstodisking,cavityandcrownpreps,
polishing,postandpindrillingandpinsetting.
Swivel
BearingAssembly
ISOConnector
Tubing
Coupler
Tubing
2. Disconnect swivel from handpiece if necessary. Grasp the swivel in front of the bearing
assemblybetweenthethumbandindexngerasshown.
3. SlidetubingcoupleruntiltheendoftheISOconnectorisexposed;holdinhandasshown
withngerssecuringthetubing.
4. AlignandinsertswiveltubesintotheISOconnectorholes.
5. Whileapplyingslightpressuretoholdttingsintheconnectorholes,slidecouplerforward
andengagethreads.Continuethreadingcouplerclockwiseuntilhandtightagainsttheswivel.
Wrench Tubing
Coupler TurnCouplerWhileHolding
SwivelinPlace
6. Usingthewrenchasshown,tighten theswivel to thetubing coupler.Besuretoturntubing
coupler,notswivel.DONOTOVERTIGHTEN.
Note: Thisjointloosensovertime,resultinginlossofpower.Checkfortightnessperiodically.
7. Connecthandpiecetoswivel.
8. Usinganairpressuregaugefor4-line,StarDentalPart#262591,betweenswivelandtubing,
obtainareading.Adjusttheairpressureatdeliveryhead until gaugereads40-45 psiwhile
operatinghandpieceinfullforwardpositionandwithfootcontrolcompletelydepressed.
Note:Ifdeliveryunithasoil/mistlubrication,detachanddrain;handpieceneedsnolubrication.
Installation - Fixed Back End Motor
Titan E
20,000 rpm - Lube Free
Made in the U.S.A.
JXXXXX
®
StarDental
®
Direction&Speed
ControlRing
RearEndConnector
20KFixedBackEndMotor
(StarDental®Part #266132)
Note:Ifdeliveryunithasoil/mistlubrication,detachanddrain;motorisLUBEFREE.
NOTICE Topreventdamagetobearings,beforeinstallingalwayscheckdriveairpressureby
usingairpressuregauge,StarDentalPart#262591(4/6-Line)betweenmotorandtubingand
obtainareading.Adjustairpressureatdeliveryheaduntilgaugereads40-45psiwhileoperating
motorandwithfootcontrolcompletelydepressed.
1. Examinetubing.Verifytubinguses4-Lineconnection.
2. Toconnectmotortotubing,aligndriveairandexhausttubeswithmatingISOconnectorholes
incoupler.
3. Whileapplyingslightpressuretoholdtubinginconnectorholes,slidetubingcouplerforward
andengagethreads.Continuethreadingtubingcouplerclockwiseuntil
handtightagainstthemotor.DONOTOVERTIGHTEN.
Note:Thisjointloosensovertime,resultinginairleakageandlossofpower.Checkfor
tightnessperiodically.
Operation
The120°rotationspeedadjustmentringsetsdirectionandspeed.Torunmotorforwardatfull
speed,rotateringtowardstheletter‘F’whileoperatingthefootcontrol.Rotatetotheletter‘R’to
yieldfullspeedinreverse.Varyspeedbyrotatingringineitherdirectiontowardscenter.Note
thesmalldepressionforthecurrentsetting.Aftersetting,themotorrunsatcurrentspeedand
directionuntilreset.Pausingthemotorisnotneededtoalterdirectionorspeedusingthering.
Titan E
20,000 rpm - Lube Free
Made in the U.S.A.
JXXXXX
®
StarDental
®
SmallDepression
120°RotationSpeed
AdjustmentRing
ATTACHMENTS
TheTitan-E20KMotorisdesignedtoworkwithallstandardE-Typeattachments.
Titan E
20,000 rpm- Lube Free
Made in the U.S.A.
JXXXXX
®
StarDental
®
StraightNoseCone
Motor-to-Angle
Contra-AngleAttachment
20KTitan-EMotor
ANGLE INSTALLATION
StarDental Titan angles can be attached to E-Type Motor-to-Angle
Contra-AngleAttachments .
ToinstallaTitanAngle:
1. Unthreadknurledring.
2. Pullknurledringenoughtoshowsplines,remove
knucklefromangle*. Splines
Knuckle
Knurled Ring
Titan 3 LubeFree Ball Bearing
Auto Latch Angle Head
*Note:Savetheknuckleinasafeplace.Youwill
needtheknuckletouseanglewithTitan
attachments.
StraightNoseCone:
Attachtomotor.Installburaccordingtomanufacturer'sinstructions.
NOTICE AnyseriousincidentoccurringfromtheuseofthisdeviceshouldbereportedtoStarDental
immediately.IfincidentoccurredinaEUMemberStatethecompetentauthoritymust
benotied.

3. CarefullymeshthesplinesontheanglewiththesplinesoftheMotor-to-AngleContra-Angle
Attachment
 (seeillustrationbelow).
4. Tightenknurledringontothreadsuntilsnug.
5. Installburaccordingtotheangle’sinstructionmanual.
7LWDQ (
USP/XEH)UHH
0DGHLQWKH86$
-;;;;;

6WDU'HQWDO

Splines
Angle
Motor-to-Angle
Contra-AngleAttachment
Titan-EMotor
TransmissionGear
CAUTIONWhenangledoesnotseatonattachment,gearsarenotmeshedcorrectly.Remove
angle;spinangletransmissiongearandrepeatStep3.
Titan E
®
StarDental
®
Internal
Surfaces
SwivelBearing/
SpringAssembly
Clean
Cleaning & Sterilization
CAUTION
INSTRUCTIONS
Maintenance &Lubrication: TheTitan®-EMotorisLubeFreeand,therefore,requiresnolubrication.Motorshouldberoutinely
maintained,checkedforcorrosion,wornparts,etc.andshouldbereplacedonanasneededbasis.
WARNING
Donotexceed135°C
Donotuse:
Limits on Reprocessing
Thehandpiecemotormustbecleanedandsterilizedbeforerstuseandbetweenpatientuse.
Cleaning-Manual: TheTitan®-EMotorisLubeFreeand,therefore,requiresnolubrication.
Attimesdebrisfromthedeliverysystem’sdriveairtubingcollectsinthemotor.Thisbuild-up
maycausesluggishmotoroperation.Toease,place3dropsofDentaLube II,StarDental®Part
#262539intothedriveairtubeofmotor,andalternatelyoperatethemotorinforwardand
reverse.
Cleaning the Swivel, the Mating Motor Part
Cleanallinternalsurfacesatrearofhandpiecemotorwithacottonswabsoakedin
isopropylalcoholuntilclean.
Cleanallexternalsurfacesusingasmalltoothbrushwithisopropylalcohol.
Tooptimizeoperationoftheswivelconnector,cleanallinternalsurfacesofthemotorwith
acottonswabsoakedinisopropylalcoholuntilclean.Cleanareaaroundbearing/spring
assemblyatrearofswivelusingisopropylalcoholandatoothbrush.Drybothusingsyringeair.
Cleaning-Automated: Washer-disinfectorsarenotrecommended.
Wrapped Instrument
Sterilization:
GravityTypeAutoclave:Pre-VacuumAutoclave:
•Minimumof15minutesat132°C•Minimumof4minutesat132°C
•Minimumof30minutesat121°C
Donotexceed135°C
•dryheatsterilizer
•immersiontechniques
•coldsterilizers •ultrasoniccleaners
•sterilizerbagscontainingdisinfectants •handsoaps
•detergents
•chemicaldisinfectors
•surfacesprays •surgicalmilk •surfacewipes
Additional Information: Do not exceed the sterilizer manufacturer’s guidelines for load capacity. Use only paper or
paper/plasticbags.
Storage: Storeinbagaftersterilizationuntilreadytouse.
Repeatedprocessinghasminimaleffectontheseattachments.Endoflifeisnormally
determinedbywearanddamageduetouse.
Drythemotorfor30minutesminimumusingthesterilizationdrycycleandallowthemotorto
cooltoroomtemperatureinbagpriortouse.Ifmoistureispresent,increaseyoursterilizerdry
cycleappropriately.
Drying:
Containment andtransportation: Itisrecommendedthathandpiecesarereprocessedassoonasisreasonablypracticalfollowinguse.
Preparation for cleaning: Wearpuncture-resistantglovesandprotectiveeyewear.Aftereachpatient,ushairbyrunning
handpiecemotorfor20seconds.Removemotorfromswivelifapplicableortubing.
Usesteamsterilizationexclusivelyforcompletesterilityasoutlinedbelow.
Disinfection:
SeeInstallation,OperatingRecommendations,and/orTroubleshootingsectionsofthismanual.
Inspection & function testing:
Single:Astandardsterilizationpackagingmaterialmustbeused.Ensurethatthepackislarge
enoughtocontaintheitemwithoutstressingtheseals.
Packaging:
Manufacturer Contact: Seerstorlastpanelsofthismanual.
StarDental®
Instrument Solutions
StarDental®
Instrument Solutions
7LWDQ (

6WDU'HQWDO

7LWDQ (

6WDU'HQWDO

Drive
Air
RedTip
Applicator
ItistheresponsibilityoftheusertouseonlyFDAcompliantsterilizingequipmentandaccessories
thatarecapableofmeetingthemanufacturersrecommendationsbelow.
CAUTION
Troubleshooting
Problem: LACK OF POWER
Cause:  Airpressure
Correction:  Verifyproperhandpieceairpressure.RefertoInstallation.
Cause:  Crimpedtubing
Correction:  Straightentubinginsideandoutsidedeliveryhead.
Cause:  Swivelnotthreadedfullyontotubing
Correction:  RefertoInstallation.
Cause:  Brittlemotororswivelsiliconerubberseal
Correction:  Replacesiliconerubbersealfor2/3-lineswivelwithStarDentalPart#203103
and4-linewithStarDentalPart#202897.
Cause:  SwivelO-ringsworn
Correction:  ReplaceswivelO-rings,StarDentalPart#259884.
Cause:  Debrisbuild-upinhandpiece
Correction:  Cleanhandpiece.RefertoCleaning.
Problem: SWIVEL WILL NOT DISENGAGE FROM HANDPIECE
Cause:  Build-upofdebris
Correction:  Place3dropsofDentaLube II,StarDentalPart#262539,intotheswivel/tubing
connector.Rotateswiveltocirculatelube.Disengagehandpiece.Contactdealer
ifunabletodisengageswivel.Topreventreoccurrence,refertoCleaning.
Note: Ifaproblempersists,contactdealerforfurtherassistanceorcontactStarDental technical
serviceat1-866-DTE-INFO.
AlwaysinsistonStarDentalpartsforbestperformance.
Replacement Part Numbers
Titan 3 Titan T
Description Item Number Item Number
AirPressureGaugefor4/6-Line.....................................................262591............................................................262591
SiliconeRubberSeal,4-Line(Pkg.of3).......................................202897...........................................................202897
DentaLube II............................................................................................262539...........................................................262539
ACCESSORIES
Swivel,Motor2/3-Line.......................................................................260152............................................................260152
Swivel,Motor4-Line............................................................................260144............................................................260144
LubeFreeBallBearingAutoLatchAngle......................................264146........................................................... 263950
LubeFreeBallBearingManualLatchAngle................................262738........................................................... 263948
LubeFreeBallBearingAutochuckFrictionGripAngle..................264151........................................................... 263954
LubeFreeBallBearingManualChuckFrictionGripAngle...........262740
BallBearingAutoLatchAngle..........................................................264182
BallBearingManualLatch.................................................................259005...........................................................263947
BallBearingAutochuckFrictionGripAngle...............................264149
TitanEndodonticAngle,AutoLatch..............................................262570............................................................ 262570
TitanEndodonticAngle,ManualLatch........................................262571............................................................ 262571
For new products, manuals and technical information, call
1-866-DTE-INFO or visit our web site at www.dentalez.com.
Important Notice About
Returning Product To The DentalEZ Inc.
Anyone wishing to return any DentalEZ Inc. product to a DentalEZ facility MUST obtain the proper
RETURN AUTHORIZATION NUMBER from the Customer Service Department. The RA Number must
appear clearly marked on both the outside and inside of the returned product carton. When calling for
a return authorization number you will be asked to provide the following information:
To Obtain A
Return Authorization
Number Call
1-866-DTE-INFO
Items will be evaluated. Return Authorization Number is not a guarantee for credit. Your cooperation
with this procedure will help us expedite processing of any returns.
• Product Name, Model Number or Part Number
• Serial Number of Product
• Dealer Return Purchase Order Number
• Reason For Return
• Copy of Invoice Showing Purchase
Limited Warranty
O-RingsandSealsarespecicallyexcludedfromthiswarranty.
DentalEZ®warrantstheTitan
®-EMotorfor1yearfromthedateofpurchase*.
Pleasenotethefollowingadditionaltermsofourwarrantypolicy:
• Warrantiescovermanufacturingdefectsonlyanddonotcoverdefectsresultingfrom
abuse,improperhandling,cleaning,careormaintenance,normalwearandtearor
non-observanceofoperating,maintenanceorinstallationinstructions.Failure to use
authorized parts or an authorized repair facility voids this warranty.
• Liability is limited to repair or replacement of the defective product at our sole
discretion. All other liabilities, in particular liability for damages, including,
without limitation, consequential or incidental damages are excluded.
• THISWARRANTYISINLIEUOFALLOTHERWARRANTIES,EXPRESSEDORIMPLIED,
INCLUDINGANYIMPLIEDWARRANTIESOFMERCHANTABILITYORFITNESSFORA
PARTICULARPURPOSE.NOEMPLOYEE,REPRESENTATIVEORDEALERISAUTHORIZED
TOCHANGETHISWARRANTYINANYWAYORTOGRANTANYOTHERWARRANTY.
*Providedconditionsinwarrantyaremet.
WARRANTY REGISTRATION
PLEASEVISITTHEWEBSITEBELOWTOREGISTERYOURSTARDENTALPRODUCT.THISWILL
ENSUREPROPERREGISTRATIONANDPROMPTANDACCURATESERVICESHOULDANYOFYOUR
PURCHASESNEEDEVALUATIONORREPAIRDURINGTHEWARRANTYPERIOD.
StarDental®Products:www.dentalez.com/warranty