Desa RCP200V User manual

Save this manual for future reference.
Save this manual for future reference.
PROPANE
CONSTRUCTION HEATER
OWNER’S MANUAL
TM
IMPORTANT: Read and understand this manual before assembling, starting, or servicing
heater.Improperuseofheatercancauseseriousinjury.Keepthismanualforfuturereference.
Models: TC200V and RCP200V
GENERAL HAZARD WARNING:
FAILURETOCOMPLYWITHTHEPRECAUTIONSANDINSTRUCTIONSPROVIDEDWITHTHIS
HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR
DAMAGE FROM HAZARDS OF FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON MON-
OXIDE POISONING AND/OR ELECTRICAL SHOCK.
ONLYPERSONSWHOCANUNDERSTANDANDFOLLOWTHEINSTRUCTIONSSHOULDUSE
OR SERVICE THIS HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS
MANUAL, LABELS, ETC. CONTACT THE MANUFACTURER.
AT
PUSH
TOSTART
LO
HI

103886-01F
2
For more information, visit www.desatech.com
For more information, visit www.desatech.com
TABLE OF CONTENTS
SAFETY INFORMATION
SAFETY INFORMATION
WARNING: FIRE, BURN, INHALATION, AND EX-
PLOSION HAZARD. KEEP SOLID COMBUSTIBLES,
SUCHASBUILDINGMATERIALS,PAPEROR CARD-
BOARD, A SAFE DISTANCE AWAY FROM THE
HEATER AS RECOMMENDED BY THE INSTRUC-
TIONS.NEVERUSETHEHEATERINSPACESWHICH
DO OR MAY CONTAIN VOLATILE OR AIRBORNE
COMBUSTIBLES, OR PRODUCTS SUCH AS GASO-
LINE,SOLVENTS,PAINTTHINNER,DUSTPARTICLES
OR UNKNOWN CHEMICALS.
WARNING:NOTFORHOMEORRECREATIONAL
VEHICLE USE.
The heater is designed for use as a construction heater in accordance
with ANSI Z83.7/CGA 2.14. Other standards govern the use of fuel
gases and heating products for specific uses. Your local authority can
adviseyouaboutthese.Theprimary purpose of construction heaters is
toprovidetemporaryheatingofbuildingsunderconstruction,alteration
or repair. Properly used, the heater provides safe economical heating.
Products of combustion are vented into the area being heated.
We cannot foresee every use which may be made of our heaters.
CHECKWITHYOURLOCALFIRESAFETYAUTHORITY
IF YOU HAVE QUESTIONS ABOUT HEATER USE.
Other standards govern the use of fuel gases and heat producing
products for specific uses. Your local authorities can advise you
about these.
Carbon Monoxide Poisoning: Some people are more affected
by carbon monoxide than others. Early signs of carbon monoxide
WARNINGS
Propane Gas: Propane gas is odorless. An odor-making agent is
addedtopropane gas. Theodorhelpsyou detect apropanegasleak.
However,theodoraddedtopropanegasmayfade.Propanegasmay
be present even though no odor exists.
Make certain you read and understand all warnings. Keep this
manual for reference. It is your guide to safe and proper operation
of this heater.
• Install and use heater with care. Follow all local ordinances and
codes. In the absence of local ordinances and codes, refer to the
Standard for Storage and Handling of Liquefied Petroleum Gas,
ANSI/NFPA 58 and the Natural Gas Installation Code, CAN/
CGA B149.2. This instructs on the safe storage and handling of
propane gases.
• This product has been approved for use in the Commonwealth
of Massachusetts.
• Use only propane gas set up for vapor withdrawal.
• Provideadequateventilation. Before using heater, provide at least
a six-square-foot opening of fresh, outside air. This heater pro-
duces carbon monoxide, which is listed by the State of Califor-
nia as a reproductive toxin under Proposition 65.
• For indoor use only. Do not use heater outdoors.
• Keep heater away from strong drafts, wind, water spray, rain, or
dripping water.
• Do not use heater in occupied dwellings or in living or sleeping
quarters.
• Do not use heater in a basement or below ground level. Propane
gas is heavier than air. If a leak occurs, propane gas may sink to
the lowest possible level.
• Keepapplianceareaclearandfreefromcombustiblematerials, gaso-
line, paint thinner, and other flammable vapors and liquids. Dust is
combustible. Do not use heater in areas with high dust content.
• Minimum heater clearances from combustibles:
Sides: 3 feet, Top: 7 feet.
• Keep heater at least six feet from propane tank(s).
TABLE OF CONTENTS
SAFETY INFORMATION ............................................................ 2
PRODUCT IDENTIFICATION ..................................................... 3
UNPACKING ............................................................................... 3
THEORY OF OPERATION ......................................................... 3
PROPANE SUPPLY .................................................................... 3
VENTILATION............................................................................. 4
INSTALLATION ........................................................................... 4
OPERATION ............................................................................... 4
STORAGE................................................................................... 5
MAINTENANCE .......................................................................... 5
REPLACEMENT PARTS ............................................................ 5
SPECIFICATIONS ...................................................................... 6
TROUBLESHOOTING ................................................................ 6
ACCESSORIES .......................................................................... 6
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST......... 7
WARRANTY INFORMATION...................................... Back Cover
WARNING:Thisproductcontainsand/orgenerates
chemicals known to the State of California to cause
cancer or birth defects, or other reproductive harm.
poisoning resemble the flu, with headaches, dizziness, and/or nau-
sea.Ifyouhavethesesigns,theheatermaynotbeworkingproperly.
Getfreshairatonce!Checkforproperventilation andhaveheater
serviced.

103886-01F
3
3
For more information, visit www.desatech.com
For more information, visit www.desatech.com
SAFETY INFORMATION
UNPACKING
THEORY OF OPERATION
PRODUCT IDENTIFICATION
PROPANE SUPPLY
• Keep propane tank(s) below 100° F.
• Check heater for damage before each use. Do not use a dam-
aged heater.
• Use only the hose and factory preset regulator provided with the
heater.
• Check hose before each use of heater. If highly worn or cut,
replace with hose specified by manufacturer before using heater.
• Do not alter heater. Keep heater in its original state.
• Do not use heater if altered.
• Locate heater on stable and level surface if heater is hot or
operating.
• Not intended for use on finished floors.
• Never block air inlet (bottom of shell) or air outlet (around top
of shell) of heater.
• Do not leave heater unattended.
• Keep children and animals away from heater.
• Never move, handle, or service a hot or operating heater. Severe
burns may result. Wait 15 minutes after turning heater off.
• To prevent injury, wear gloves when handling heater.
• Never attach duct work to heater.
• Turn off propane supply to heater when not in use.
• Use only original replacement parts. This heater must use de-
sign-specific parts. Do not substitute or use generic parts. Im-
proper replacement parts could cause serious or fatal injuries.
SAFETY INFORMATION
Continued
PRODUCT IDENTIFICATION
UNPACKING
1. Remove all packing items applied to heater for shipment. Keep
plastic cover caps (attached to valve inlet and hose/regulator
assembly) for storage.
2. Remove all items from carton.
3. Check all items for shipping damage. If heater is damaged,
promptly inform dealer where you bought heater.
THEORY OF OPERATION
The Fuel System: The hose/regulator assembly attaches to the
propane gas supply. This provides fuel to the heater.
TheIgnition System:Thepiezoignitorlightstheburnerfuelsupply.
TheAutomaticControlSystem:Theautomaticcontrolvalveshuts
off the heater if the flame goes out.
AT
PUSH
TOSTART
LO
HI
Hose/
Regulator
Assembly
Shell
Base
Piezo
Ignitor
Button
Ignitor
Electrode
Thermocouple
Valve Inlet Control Knob
Top
Figure 1 - Product Identification
PROPANE SUPPLY
You must provide propane gas and tank(s).
Use this heater only with a propane vapor withdrawal supply
system. See Chapter 5 of the Standard for Storage and Handling of
LiquefiedPetroleumGas,ANSI/NFPA58and/orCAN/CGAB149.2.
Your local library or fire department will have this booklet.
Theamountofpropanegasreadyforusefrompropanetanksvaries.
Two factors decide this amount.
1. The amount of liquid propane gas in tank(s)
2. The temperature of tank(s)
The chart below shows the minimum number of 100-pound tanks
neededtoruntheheater.Connecttankstogetherwithamanifold.Do
not operate this product with any tank smaller than 100 pounds.
Average Temp. (°F) Number Of
At Tank Location Tanks
60° 2
40° 2
32° 2
20° 2
10° 3
0° 3
Lessgasisvaporized atlowertemperatures.Twoormore100-pound
tanks or one larger tank may be needed in colder weather. Your local
propane gas dealer will help you select the proper supply system.

103886-01F
4
For more information, visit www.desatech.com
For more information, visit www.desatech.com
VENTILATION
FRESH OUTSIDE AIR OPENING REQUIREMENTS
HEATER SIZE SQ. FT. OPENING
200,000 Btu/Hr 6.0
WARNING: Provide at least a 6 square foot open-
ingoffresh,outsideairwhilerunningheater.Ifproper
fresh, outside air ventilation is not provided, carbon
monoxidepoisoningcanoccur.Provideproperfresh,
outside air ventilation before running heater.
INSTALLATION
1. Provide propane supply system (see Propane Supply, page 3).
2. Connect fuel gas fitting on hose/regulator assembly to pro-
panetank(s).Turnfuelgasfitting counterclockwise into threads
ontank.Tighten firmly using a wrench. IMPORTANT: Tighten
regulator with vent pointing down. Pointing vent down pro-
tects regulator from weather damage.
3. Connect hose to the valve inlet. Tighten firmly using a wrench.
You must use the regulator supplied with heater even if pro-
pane tank has one.
4. Open propane supply valve on propane tank(s) slowly. Note:
If not opened slowly, excess-flow check valve on propane tank
may stop gas flow. If this happens, you may hear a click inside
the regulator assembly, this is the check valve closing. To re-
set the excess-flow check valve, close propane supply valve
and open it again slowly.
5. Check all connections for leaks.Apply mixture of liquid soap
and water to gas joints. Bubbles forming show a leak that must
be corrected.
6. Close propane supply valve.
WARNING: Test all gas piping and connections
for leaks after installation or servicing. Never use an
open flame to check for a leak. Apply a mixture of
liquid soap and water to all joints. Bubbles forming
show a leak. Correct all leaks at once.
WARNING: Review and understand the warnings
inthe SafetyInformation section,pages2and3.They
are needed to safely operate this heater. Follow all
local codes when using this heater.
Figure 3 - Hose and Valve Inlet
Figure 2 - Regulator With Vent Pointing Down
Propane Tank
Supply Valve
Fuel Gas
Fitting Hose
Regulator
Vent
(pointing down)
AT
PUSH
TOSTART
LO
HI
Hose
Valve Inlet
WARNING: Review and understand the warnings
in the Safety Information section on pages 2 and 3.
Theyare neededto safelyoperate thisheater. Follow
all local codes when using this heater.
OPERATION
TO START HEATER
1. Follow all installation, ventilation, and safety information.
2. Locate heater on stable and level surface. Make sure strong
drafts do not blow on heater.
3. Open propane supply valve on propane tank(s) slowly. Note:
If not opened slowly, excess-flow check valve on propane tank
may stop gas flow. If this happens, you may hear a click inside
the regulator assembly, this is the check valve closing. To re-
set the excess-flow check valve, close propane supply valve
and open it again slowly.
4. Turn control knob clockwise to the lowest position and push
in (see Figure 4, page 5).
5. With the control knob pushed all the way in, press and release
the piezo ignitor button (see Figure 4, page 5). Keep pressing
piezo ignitor button until the burner lights. Hold control knob
down for a maximum of 10 seconds while attempting ignition.
If heater does not ignite, release control knob and wait 3 min-
utes before attempting reignition.
Note: Keep hands and face away from outlet (around top of shell)
of heater while attempting to start heater.
VENTILATION
INSTALLATION
OPERATION

103886-01F
5
5
For more information, visit www.desatech.com
For more information, visit www.desatech.com
CAUTION:Donotoperateheateratextremelylow
input gas pressures (100% yellow flame). This may
cause sooting inside heater.
6. After ignition, hold control knob down for about 30 seconds.
This activates the automatic control system.
7. When burner remains lit, set heater at the desired heat level by
turning the control valve counterclockwise. If burner goes out,
turn off gas. Turn control knob fully clockwise to the lowest
position. Check fuel supply. If adequate fuel is available, re-
start heater beginning at step #1.
OPERATION
Continued
Figure 4 - Control Knob, and Piezo Ignitor Button Locations
TO STOP HEATER
1. Tightly close propane supply valve on propane tank(s).Allow
heater to burn remaining fuel in hose.
2. Shut off main burner valve. Do this by turning control knob
fully clockwise. Make sure you turn the knob until it stops.
TO RESTART HEATER
1. Wait five minutes after stopping heater.
2. Restart heater by following steps under To Start Heater, page 4.
AT
PUSH
TO START
LO
HI
AT
PUSH
TO START
LO
HI
Piezo
Ignitor
Button
Control Knob
STORAGE
CAUTION: Disconnect heater from propane sup-
ply tank(s).
MAINTENANCE
1. Store propane tank(s) in safe manner. Refer to Chapter 5 of
Standard for Storage and Handling of Liquefied Petroleum
Gases, ANSI/NFPA 58 and/or CAN/CGA B149.2. Follow all
local codes. Always store propane tanks outdoors.
2. Place plastic cover caps over brass fittings on valve inlet and
hose/regulator assembly.
3. Store in a dry, clean, and safe place.
1. Keep heater clean.
2. Inspect heater before each use. Check connections for leaks.
Applymixture of liquid soap and water toconnections.Bubbles
forming show a leak that must be corrected. Correct all leaks
at once.
3. Inspecthose/regulatorassemblybeforeeach use. Ifhoseishighly
worn or cut, replace with hose specified by manufacturer.
4. Have heater inspected yearly by a qualified service person.
WARNING:Neverattempt toservice heaterwhile
it is connected to propane supply, operating, or hot.
Severe burns can occur.
REPLACEMENT PARTS
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If they can’t supply
original replacement part(s), either contact your nearest Parts Cen-
tral or call DESA International’s Technical Service Department at
1-866-672-6040. When calling DESA International, have ready
• your name
• how heater was malfunctioning
• your address
• purchase date
• model and serial numbers of your heater
In most cases, we will ask you to return the part to the factory.
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. If they can’t supply
original replacement part(s), either contact your nearest Parts Cen-
tral or call DESA International at 1-866-672-6040 for information.
When calling DESA International, have ready
• model number of your heater
• the replacement part number
WARNING: Use only original replacement parts.
This heater must use design-specific parts. Do not
substitute or use generic parts. Improper replace-
ment parts could cause serious or fatal injuries. This
will also protect your warranty coverage for parts
replaced under warranty.
OPERATION
STORAGE
MAINTENANCE
REPLACEMENT PARTS

103886-01F
6
For more information, visit www.desatech.com
For more information, visit www.desatech.com
SPECIFICATIONS
Rating (BTU/Hr) High - 200,000
Low - 100,000
Fuel Propane Vapor Only
Fuel Consumption Gallons/Hour - 1.09min./2.19 max.
Pounds/Hour - 4.64min./9.28 max.
Supply Pressure (To Regulator)
Maximum - 200 psi
Minimum - 20 psi
(for input adjustment)
Manifold Pressure High - 4.6 psi
Low - 5.9 psi
Weight (lbs) 16
Shipping Weight (lbs) 20
Size - L x W x H (in.) 30 x 15 x 16
Minimum Temp. -20°F (-29°C) Surrounding Air
TROUBLESHOOTING
Youmayhavefurtherquestionsaboutthisheater.Ifso,contactDESA
International’s Technical Service Department at 1-866-672-6040.
WARNING: Never attempt to service heater while
it is connected to propane supply, operating, or hot.
Severe burns can occur.
SYMPTOM
Burner fails to light
Burner lights but goes out when automatic
control valve button is released
Burn rate is low
POSSIBLE CAUSE
1. Propane supply valve closed on propane
tank(s)
2. Excess-flow check valve closed
3. Blockage in burner nozzle
4. Piezo ignition system not sparking
1. Not enough warm-up time
2. Low gas pressure
3. Thermocouple loose or needs to be re-
placed
4. Automatic control valve needs to be re-
placed
1. Main burner valve not fully open
2. Plugged gas orifices
3. Low gas pressure
4. Low fuel supply
REMEDY
1. Open propane supply valve slowly
2. Close propane supply valve on propane
tank and reopen slowly
3. Replace burner nozzle
4. Check to assure ignitor electrode gap is
.130". Check wire lead for damage. Re-
place piezo ignitor and/or ignitor elec-
trode as necessary
1. Relight, hold automatic control valve
button in 45 seconds
2. Check propane tank(s) for proper gas
supply
3. Tighten connection or replace thermo-
couple
4. Replace automatic control valve
1. Fully open main burner valve by turn-
ing control knob towards HIGH posi-
tion until it stops
2. Replace gas orifice
3. Check gas supply; check regulator output
4. Consult propane gas supplier
ACCESSORIES
Purchase these accessories and parts from your local dealer or
service center. If your dealer or service center can not supply an
accessory or part, contact your nearest Parts Central (listed in the
separate Authorized Service Center booklet) or call DESA Interna-
tional at 1-866-672-6040 for referral information. You can also
write to the address listed on the back page of this manual.
Part Number Description
LPA1020 10' Rubber Hose with Brass Fitting
U.L. listed.
LPA2005 Propane Gas Regulator
U.L. listed.
LPA3005 Hose/Regulator Assembly
U.L. listed.
LPA4020 Fuel Gas Connector
Connects regulator to all standard
propane tanks. U.L. and A.G.A. listed.
SPECIFICATIONS
TROUBLESHOOTING
ACCESSORIES

103886-01F
7
7
For more information, visit www.desatech.com
For more information, visit www.desatech.com
ILLUSTRATED PARTS
BREAKDOWN AND PARTS LIST
This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 5
of this manual.
KEY PART
NO. NO. DESCRIPTION QTY.
1 103925-01 Top and Shell Assembly 1
2 103923-01 Burner Ring Assembly 1
3 101263-01 Burner Plate 1
4 097162-02 Burner Nozzle 1
5 103031-02 Base 1
6 103924-01 Knob Assembly 1
7 102445-01 Piezo Ignitor 1
8 099236-01 Thermocouple Kit 1
9 103906-01 Thermocouple Bracket 1
10 103927-01 Fuel Tube Kit 1
11 103926-01 Valve Assembly 1
12 103398-01 Ignitor Electrode 1
13 103396-01 Heat Shield 1
PARTS AVAILABLE - NOT SHOWN
098853-07 Tradename Decal (TC200V) 1
098851-06 Tradename Decal (RCP200V) 1
098831-05 Information Decal 1
101284-02 Operation Decal 1
ACCESSORIES
LPA3005 Regulator & Hose Assembly 1
LPA4020 Fuel Gas Connector 1
AT
PUSH
TOSTART
LO
HI
1
5
43
2
6
13
10
9
8
7
11
12
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST

103886-01F
8
For more information, visit www.desatech.com
For more information, visit www.desatech.com
103386-01
Rev. F
09/02
LIMITED WARRANTY
DESA International warrants this product and any parts thereof, to be free from defects in materials and workmanship for one (1) year from the date
of first purchase when operated and maintained in accordance with instructions. This warranty is extended only to the original retail purchaser, when
proof of purchase is provided.
Thiswarranty covers onlythe cost ofparts and laborrequired to restorethe product toproper operating condition.Transportationand incidentalcosts
associated with warranty repairs are not reimbursable under this warranty.
Warranty service is available only through authorized dealers and service centers.
This warranty does not cover defects resulting from misuse, abuse, negligence, accidents, lack of proper maintenance, normal wear, alteration,
modification,tampering,contaminatedfuels,repairusingimproperparts,orrepairbyanyoneotherthananauthorizeddealerorservicecenter.Routine
maintenance is the responsibility of the owner.
THIS EXPRESS WARRANTY IS GIVEN IN LIEU OF ANY OTHER WARRANTY EITHER EXPRESSED OR IMPLIED, INCLUDING
WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
DESA International assumes no responsibility for indirect, incidental or consequential damages. Some states do not allow the exclusion or limitation
of incidental or consequential damages, or limitations or exclusions may not apply to you. This Limited Warranty gives you specific legal rights and
you may also have other rights which vary from state to state.
WARRANTY AND REPAIR SERVICE
KEEP THIS WARRANTY
This warranty does not cover discoloration due to operation of heater. We reserve the right to amend these specifications at any time without notice.
The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.
WARRANTY SERVICE
Should your heater require service, return it to your nearest authorized service center. Proof of purchase must be presented with the heater. The heater
willbeinspected.Adefectmaybecausedbyfaultymaterialsorworkmanship.Ifso,DESAInternationalwillrepairorreplacetheheaterwithoutcharge.
REPAIR SERVICE
Returnyourheater toyournearestauthorized servicecenter.Repairsnot coveredbythewarranty willbebilledat standardprices.EachService Center
is independently owned and operated. We reserve the right to amend these specifications at any time without notice.
For information, write: DESA International, P.O. Box 90004
Bowling Green, Kentucky 42102-9004 ATTN: Customer Service Department
When writing, always include model number and serial number.
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
Model
Serial No.
Date of Purchase
NOT A UPC
TM
103386 01