Desa Comfort Glow CGCF26TN Quick start guide

VENT-FREE NATURAL GAS
COMPACT FIREPLACE
OWNER'S OPERATION AND INSTALLATION MANUAL
14,000 to 26,000 Btu/Hr
with Thermostat
CGCF26TN
Shown with Optional
Cabinet Mantel/Hearth
Base Accessory
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result caus-
ing property damage, personal injury, or loss of life.
-- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
•Do not touch any electrical switch; do not use
any phone in your building.
•Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
•If you cannot reach your gas supplier, call the
fire department.
-- Installation and service must be performed by a
qualified installer, service agency, or the gas supplier.
WARNING: Improper installation,
adjustment, alteration, service, or
maintenance can cause injury or
property damage. Refer to this
manual forcorrect installation and
operational procedures. For as-
sistance or additional informa-
tion consult a qualified installer,
service agency, or the gas sup-
)lier.
WARNING: This is an unvented
gas-fired heater. It uses air (oxy-
gen) from the room in which it is
installed. Provisions foradequate
combustion and ventilation air
must be provided. Refer to Air for
Combustion and Ventilation sec-
tion on page 6 of this manual.
This appliance may be installed in an aftermarket* manufactured (mobile) home, where not
prohibited by state or local codes.
*Aftermarket: Completion of sale, not for purposeof resale,from the manufacturer. (I.E.Installationof this
product ispermitted afterthe manufactured(mobile) home issited)
This appliance Is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases.

CONTENTS
SAFETY
INFORMATION
[]
SECTION PAGE
Safety Information ................................................................................... 2
Product Identification .............................................................................. 4
Local Codes ............................................................................................. 4
Product Features ...................................................................................... 4
Unpacking ................................................................................................ 4
Assembly ................................................................................................. 4
Air for Combustion and Ventilation ........................................................ 6
Installation ............................................................................................... 10
Connecting to Gas Supply ....................................................................... 16
Checking Gas Connections ...................................................................... 18
Operating Fireplace ................................................................................. 19
Inspecting Burner .................................................................................... 22
Cleaning and Maintenance ...................................................................... 24
Troubleshooting ....................................................................................... 24
Technical Service .................................................................................... 28
Specifications .......................................................................................... 28
Service Hints ........................................................................................... 28
Replacement Parts ................................................................................... 28
Accessories .............................................................................................. 29
nlustrated Parts List ................................................................................. 30, 31
Parts Centrals ........................................................................................... 32
Warranty Information .............................................................................. Back cover
WARNINGS
IMPORTANT: Read this owner's manual carefully and completely
before trying to assemble, operate, or service this fireplace. Improper
use of this fireplace can cause serious injury or death from burns, fire,
explosion, electrical shock, and carbon monoxide poisoning.
I DANGER [
Carbon monoxide poisoning may lead to death!
Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning
resembletheflu, with headaches, dizziness, ornausea. Ifyou have these signs, the
f'u'eplacemay not be working properly. Get fresh air at once! Have fireplace
serviced. Some people are moreaffected bycarbonmonoxide than others. These
includepregnant women, people withheart orlung disease oranemia, those under
the influence of alcohol, and those at high altitudes.
Natural Gas: Naturalgas is odorless. An odor-making agent is added tonatural
gas. The odor helps you detect a natural gas leak. However, the odor added to
natural gas can fade. Naturalgas may be present even though no odor exists.
Make certain you read and understand all warnings. Keep this manual for
reference. It is your guide to safe and proper operation of this fireplace.
Safety Information continues on next page
108888

SAFETY
INFORMATION
Continued
WARNINGS Continued
WARNING: Any change to this fireplace or its controls can be dangerous.
1. This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases.
2. If you smell gas
•shut off gas supply
•do not try to light any appliance
• do not touch any electrical switch; do not use any phone in your building.
• immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions
• if you cannot reach your gas supplier, call the fire department
3. This fireplace shall not be installed in a bedroom or bathroom.
4. Never install the fireplace
• in a recreational vehicle
• where curtains, furniture, clothing, or other flammable objects are less than 36
inches from the front, top, or sides of the fireplace
• as a fireplace insert
• in high traffic areas
• in windy or drafty areas
5. Do not use this fireplace as a wood-burning fireplace. Use only the logs provided with
the fireplace.
6. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool.
Using these added items can cause sooting. Do not add lava rock around base. Rock
and debris could fall into the control area of fireplace.
7. You must operate this fireplace with the fireplace screen in place. Make sure fireplace
screen is in place before running fireplace.
8. This fireplace is designed to be smokeless. If logs ever appear to smoke, turn off
fireplace and call a qualified service person. Note: During initial operation, slight
smoking could occur due to log curing and fireplace burning manufacturing residues.
9. Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner
flame patterns. Ceiling fans can create drafts that alter burner flame patterns. Altered
burner patterns can cause sooting.
10. This fireplace needs fresh air ventilation to run properly. This fireplace has an oxygen
depletion sensor (ODS) pilot light safety system. The ODS shuts down the fireplace if
not enough fresh air is available. See Air for Combustion and Ventilation, pages 6
through 9. If fireplace keeps shutting off, see Troubleshooting, pages 24 through 27.
11. Do not run fireplace
• where flammable liquids or vapors are used or stored.
• under dusty conditions.
12. Do not use this fireplace to cook food or burn paper or other objects.
13. Never place any objects in the fireplace or on logs.
14. Fireplace front and screen becomes very hot when running fireplace. Keep children
and adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will
remain hot for a time after shut-down. Allow surfaces to cool before touching.
15. Carefully supervise young children when they are in same room with fireplace.
16. Do not use fireplace if any part has been under water. Immediately call a qualified
service technician to inspect the room fireplace and to replace any part of the control
system and any gas control which has been under water.
17. Turn off and unplug fireplace and let cool before servicing. Only a qualified service
person should service and repair fireplace.
18. Operating fireplace above elevations of 4,500 feet could cause pilot outage.
19. Do not use a blower insert, heat exchanger insert, or other accessory not approved for
use with this fireplace.
20. Do not operate fireplace if any log is broken. Do not operate fireplace if a log is
chipped (dime-sized or larger).
IB
1O3668

PRODUCT
IDENTIFICATION
LOCAL CODES
PRODUCT
FEATURES
UNPACKING
ASSEMBLY
Fireplace
Cabinet
Screen
J
Logs
Control Knob
'Ignitor Button
Figure 1 - Vent-Free Propane/LP Gas Compact Fireplace
Install and use fireplace with care. Follow all local codes. In the absence of local
codes, use the latest edition of The National Fuel Gas Code ANSI Z223, also
known as NFPA 54".
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
Safety Pilot
This fireplace has a pilot with an Oxygen Depletion Sensor Shutoff System (ODS).
The ODS/pilot is a required feature for vent-free room fireplaces. The ODS/pilot
shuts off the fireplace if there is not enough fresh air.
Piezo Ignition System
This fireplace has a piezo ignitor. This system requires no matches, batteries, or
other sources to light fireplace.
Thermostatic Heat Control
This fireplace has a thermostat sensing bulb and acontrol valve. The thermostat
will automatically modulate the heat output to maintain a consistent room tempera-
ture. This results in greater fireplace comfort. This can also result in lower gas bills.
1. Remove log box and fireplace from carton. The hood is not attached.
2. Remove all protective packaging applied to fireplace for shipment.
3. Make sure your fireplace includes one hardware packet.
4. Check fireplace for any shipping damage. If fireplace is damaged, promptly
inform dealer where you bought fireplace.
IWARNING
Always have branch support and screen In place before operating
fireplace. This prevents excessive temperatures on fireplace surfaces.
[] 10360_

ASSEMBLY
Contmued
ASSEMBLING FIREPLACE
ToolsR_uired:Phillipsscrewdfiver, 5/16"hexwrenc_ andslottedscrewddver
Installing Log
I. Remove back log, branch, and hood from log box. Discard protective packaging.
2. Remove two shipping screws above screen (see Figure 2).
3. Lift screen up and pull out to remove.
4. An optional blower is available. See Accessories, page 32. Install optional
blower now. Follow installation instructions provided with blower.
5. Gently place back log on burner support (see Figure 2). The log should fit fiat
against top of burner support. Place two #10 one-inch-long screws through burner
support into the log and tighten. Place branches on branch support (see Figure 2).
6. Reattach screen by placing notches in screen frame over shoulder screws and
pushing down.
__ ShippingScrewScrew
Sack Log
12j _
Figure 2 - Assembling Fireplace
WARNING
Failure to position the parts in accordance with these diagrams or
failure to use only parts specifically approved with this fireplace may
result in property damage or personal Injury.
Assembling Hood
1. Lift screen off heater.
2. Remove two 1-3/4" screws from louver assembly (see Figure 2). Save these screws.
Upper
Louver
Assembly
IShort
/
I -- 1-3/4" Screws
Figure 3 - Assembling Hood
3. Pull louver assembly straight out from the cabinet. Be careful not to scratch the
paint. Set louver assembly and screws aside.
4. Locate two black Phillips sheet metal screws from the hardware packet.
5. Place hood over top edge of firebox wrappol".
6. Attach hood with two short screws in center of hoed.
7. Replace upper and lower assembly and 1-3/4" screws removed in step 2. I

AIR FOR
COMBUSTION
AND
VENTILATION
m
WARNING
This heater shall not be installed In a confined space unless
provisions are provided for adequate combustion and ventilation
sir. Read the following instructions to insure proper fresh air for
this and other fuel-burnlng appliances in your home.
Today's homes are built more energy efficient than ever. New materials, increased
insulation, and new construction methods help reduce heat loss in homes. Home
owners weather strip and caulk around windows and doors to keep the cold air out
and the warm air in. During heating months, home owners want their homes as
airtight as possible.
While it is good to make your home energy efficient, your home needs to breathe.
Fresh air must enter your home. All fuel-burning appliances need fresh air for
proper combustion and ventilation.
Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from
the house to operate. You must provide adequate fresh air for these appliances.
This will insure proper venting of vented fuel-burning appliances.
PROVIDING ADEQUATE VENTILATION
The following is excerpts from National Fuel Gas Code. NFPA 54/ANSI Z223.1,
Section 5.3, Air for Combustion and Ventilation.
All spaces in homes fall into one of the three following ventilation classifications:
1. Unusually Tight Construction; 2. Unconfined Space; 3. Confined Space.
The information on pages 6 through 9 will help you classify your space and provide
adequate ventilation.
Unusually Tight Construction
The air that leaks around doors and windows may provide enough fresh air for
combustion and ventilation. However, in buildings of unusually tight construction,
rou must provide additional fresh air.
Unusually tight construction is defined as construction where:
a. walls and ceilings exposed to the outside atmosphere have a continu-
ous water vapor retarder with a rating of one perm (10_per-pa-m =)or
less with openings gasketed or sealed and
b. weather stripping has been added on openable windows and doors and
c. caulking or sealants are applied to areas such as joints around window
and door frames, between sole plates and floors, between wall-ceiling
joints, between wall panels, at penetrations for plumbing, electrical, and
gas lines, and at other openings.
If your home meets all of the three criteria above, you must provide addi-
tlonal fresh air. See Ventilation Air From Outdoors, page 9.
If your home does not meet all of the three criteria above, proceed to page 7.
Confined end Unconfined Space
The National Fuel Gas Code (ANSIZ223.1, 1992 Section 5.3) defines a confined
space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour
(4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space
and an unconfining space as a space whose volume is not less than 50 cubic feet per
1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances
installed in that space. Rooms communicating directly with the space in which the
appliances are installed*, through openings not furnished with doors, are consid-
ered a part of the unconfined space.
* Adjoining rooms are communicating only if there are doorless passageways or
ventilation grills between them.
1O3868

AIR FOR
COMBUSTION
AND
VENTILATION
Continued
DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION
Determining if You Have a Confined or Unconfined Space
Use this worksheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install fireplace plus any adjoining rooms
with doorless passageways or ventilation grills between the rooms.
1. Determine the volume of the space (length x width x height).
Length x Width x Height = cu. ft. (volume of space)
Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) =
2560 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the
volume of these rooms to the total volume of the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space
can support.
(volume of space) + 50 cu. ft. = (Maximum Btu/Hr
the space can support)
Example: 2560 cu. fi.(volumeofspace)+50cu, ft.= 51.2 or 51,200 (maximum
Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free fireplace .Btu/Hr
Gas water heater* Btu/Hr
Gas furnace Btu/Hr
Vented gas heater Btu/Hr
Gas fireplace logs Btu/Hr
Other gas appliances* +.Btu/Hr
Total = Btu/Hr
Example: Gas water heater 30,000 Btu/Hr
Vent-free fireplace + 26,000 Btu/Hr
Total = 56,000 Btu/Hr
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the
outdoors and vents to the outdoors.
4. Compare the maximum Btu/Hrthe space can support with the actual amount of Btu/Hr
used.
Btu/I-Ir (maximum the space can support)
Btu/Hr (actual amount of Bm/Hr used)
Example: 51,200 Btu/Hr (maximum the space cansupport)
56,000 Btu/Hr (actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more
than the maximum Btu/Hr the space can support. You must provide additional fresh air.
Your optious are as follows:
A. Reworkworksheet, adding the space of an adjoining room. If the extra space provides
an unconfined space, remove door to adjoining room or add ventilation grills between
rooms. See Ventilation Air From Inside Building, page g.
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 9.
C. Install a lower Btu/Hr fireplace, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space
is an unconfined space. You will need no additional fresh air ventilation.
Continued []
1o3688

AIR FOR
COMBUSTION
AND
VENTILATION
Continued
WARNING
If the area in which the heater may be operated is smaller than
that defined as an unconfined space, provide adequate combus-
tion and ventilation air by one of the methods described in the
National Fuel Gas Code, ANSI Z223.1, 1992, Section 5.3 or appli-
cable local codes.
VENTILATION AIR
Ventilation Air From Inside Building
This fresh air would come from an adjoining unconfined space. When ventilating to
an adjoining unconfined space, you must provide two permanent openings: one within
12" of the ceiling and one within 12" of the floor on the wall connecting the two spaces
(see options 1 and 2, Figure 4). You can also remove door into adjoining room (see
option 3, Figure 4). Follow the National Fuel Gas Code NFPA 54/ANSI Z223.1,
Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills
or ducts.
WARNING
Rework worksheet, adding the space of the adjoining unconfined
space. The combined spaces must have enough fresh air to supply all
appliances in both spaces.
Ventilation
Gdlls Or
intoAdjoining Remove
Room, Door into
Option 1 Adioining
Room,
Option 3
ventilation Grills
IntoAdjoining Room,
Option 2
Figure 4 -Ventilation Air from Inside Building Shown with Optional Mantel

AIR FOR
COMBUSTION
AND
VENTILATION
Continued
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or ducts. You must provide two
permanent openings: one within 12" of the ceiling and one within 12" of the floor.
Connect these items directly to the outdoors or spaces open to the outdoors. These
spaces include attics and crawl spaces.
IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has
a thermostat-controlled power vent. Heated air entering the attic will activate the
power vent.
Inlet Air Ventilated
Crawl Space
Outlet
Air
Inlet
Air
To Attic
To
Crawl
Space
Figure 5 - Ventilation Air from Outdoors Shown with Optional Mantel
m
1O3668

INSTALLATION NOTICE
A qualified service person must install fireplace. Follow all local codes.
CHECK GAS TYPE
Use only natural gas. If your gas supply is not natural gas, do not install fireplace.
Call dealer where you bought fireplace for proper type fireplace.
INSTALLATION ITEMS
Before installing fireplace, make sure you have the items listed below.
• piping (check local codes) •manual shutoff valve * • W,ejoint
• sealant (resistant to prepane/LP gas) •ground joint union •pipe wrench
• sediment trap
• An A.G.A. design-certified manual shutoff valve with 1/8" NPT tap is an acceptable
alternative to test gauge connection. Purchase the optional A.G.A. design-certified
manual shutoff valve from your dealer. See Accessories, page 29.
Note: If desired, purchase a four-sided brass trim kit for built-in installations. See
Accessories, page 29.
LOCATING FIREPLACE
WARNING I
Maintain the minimum clearances shown in Rgures 6 and 7 (page 11). If
you can, provide greater clearances from floor, ceiling, and joining wall.
You can recess firebox into the wall. You can also position fireplace in the optional
cabinet or corner mantels. IMPORTANT: Only use optional cabinet or corner mantels
specified in this manual. Purchase the optional mantel from your dealer (see
Accessories, page 29).
WARNING
Never install the fireplace
• in a bedroom or a bathroom
•in a recreational vehicle
•where curtains, furniture, clothing, or other flammable objects are
less than 36 inches from the front, top, or sides of the fireplace
• as a fireplace insert
•In high traffic areas
• in windy or drafty areas
CAUTION
This fireplace creates warm air currents. These currents move heat
to wall surfaces next to fireplace. Installing fireplace next to vinyl
or cloth wall coverings or operating fireplace where impurities in
the air (such as tobacco smoke) exist, may discolor walls.
IMPORTANT..Vent-free fireplaces add moisture to the air. Although this is beneficial
installing fireplace in rooms without enough ventilation air may cause mildew to forn
from too much moisture. See Air for Combustion and Ventilation, pages 6 through 9.
m1036v_