DesignHouse Keypad Lock User manual
Keypad Lock
Installation Instructions
WWW.TODAYSDESIGNHOUSE.COM Customer Service:1-800-558-8700
R
LOCKKEYPAD
STOP! Please read instructions before removing
Design House Keypad lock from packaging.
Tools Needed for Installation
Phillips
Screwdriver Drill Angle Ruler Flathead
Screwdriver
Removing Keypad Lock from packaging
1. Unscrew and remove Cover Loop and Plastic Gasket from Interior Panel with provided
tool Wrench.
2. Remove Interior Cover Plate screws (4) to expose Battery Box.
3. Unscrew and remove two mounting screws.
4. Interior and Exterior can be removed from the styrofoam packaging.
5. Proceed with installation of Keypad Lock.
Wrench
(Provided with lock)
Stiletto
(For door hole2-1/8)
Page.2
Chisel Hammer
R
Keypad Deadbolt Entry
Keypad Lever Entry
Lead Pencil
B
C
4*35mm screw
Interior cover plate
Interior panel
power wire
Exterior Panel
Spindle
Fig. B
B
C
4*35mm screw
Interior cover plate
Interior panel
Cover loop
power wire
Exterior Panel
Spindle
KEYPAD LOCK
BB
CC
3.5x3/4 (3.5x20MM)
screws
Single Latch
Strike Plate
4x1.38
(4x35MM) screws
Keyhole/
Cylinder Cover
Cylinder
Cover Remover
Wrench (For Lever Entry Lock)
Door Preparation
Drilling Template
Installation Instructions
1.Use template [provided] to prepare door.
Page.3 Page.4
R
Keypad Deadbolt Entry
Interior Panel Interior
Cover Plate
Packing List
Plastic Insert
4x2 (4x50MM)
screws
Manual Override
Keys
Fig.
Keypad Lever Entry
Exterior Panel
3. Insert latchto prepared doorand attached withtwo (3.5x3/4" /3.5x20MM)
screws. See Fig.1.
4. Install 4 (AA) alkaline batteries in the Battery Box on the Interior Panel.
5. Feed the power wire from the Exterior Panel (with keypad) through the door hole (A)
and latch (see Fig. 2). Connect the power wire to the battery box.
6. Attach the Exterior Panel making sure the lock Spindle is squarely inserted into mount-
ing plate on Interior Panel through door hole (A). Be sure to secure the metal panels
to the inner edges of the rubber gaskets for a sealed installation on both the interior
and exterior sides.
7. Attach the Exterior Panel and the Interior Panel with two (4x1-3/8 / 4x35MM) or
1.97" / 4x50MM) screws depending on different door thicknesses.
8. Attach the Interior Cover Plate over the Battery Box and Interior Panel.
(4x
10. Place PlasticInsert into prepared hole on door frame. AttachStrike Plate
with two self-tappingscrews.
11. Verify that theDoor Latch engages with the StrikePlate on thedoorframe.
KEYPAD LOCK
2. Drill andprepare the doorframefor the Plastic Insert and StrikePlate making
sure the holes arelevel and adirect match forthe door lockdrilling (See Fig.A).
Page.5 Page.6
Fig.A.
1-3/4
(44mm)
2-1/4
(57mm)
1-1/8
(28mm)
1/2
(13mm)
Fig.3
Door frame
Plastic Insert
Strike Plate
Fig.1
3.5x20mm screw
3.5x20mm screw
Regular Latch Deadbolt
Door panel
R
4*35mm screw
Interior cover plate
Interior panel
Fig. 2
B
C
4*35mm screw
Interior cover plate
Interior panel
Cover loop
power wire
Exterior Panel
Spindle
Keypad Lever Entry
3.5x20mm screw
3.5x20mm screw
Door panel
B
C
power wire
Exterior Panel
Spindle
Keypad Deadbolt Entry
9. Feed Cover Loop and plastic gasket ring over the interior handle. Screw Cover Ring
tightly to secure the interior assembly.(Lever Entry Only)
Attach the Interior Cover onto the Interior Panel and fix them with two (3x10mm)
screws on both sides of Interior Cover.See Fig.2. (Deadbolt Entry Only)
KEYPAD LOCK
Operating and Programming Instructions
There are two ways to open Design House Keypad Locks.
- Enter a valid 6-digit password; the green indicator light will go ON; use the lever or knob
to open the latch within 5 seconds.
- Manual override keys (for emergency use).
IMPORTANT
1. The factory set Master Code is 111111 . Please change th e Master Password to a new
6-digit Master Code on the initial use.
2. The Design House Keypad Entry Lock holds 300 User Passwords.
3. The Design House Keypad Entry Lock makes several sounds:
- Three short beeps indicate an incorrectly keyed code. Door will not unlock.
- One long beep indicates a correctly keyed code. Open the latch within 5 seconds to open
the door.
Code Definitions
Master Code = 6 digits. Required for making changes and additions to all codes. Factory
set Master must be changed the 1st time the lock is used for increased security.
Property owner/manager should keep this information confidential.
User Number = 3 digits. Identifies the user. Property owner/manager should keep a log of
User Numbers.
User Password = 6 digits. User enters this code on the keypad to gain entry into building.
Programming/Changing Codes
Changing the Master Code (initial use)
Press: ## + Factory Set Master Password + *** + New Master Password + New Master
Password
Press: ## + Master Password + #** + 3-digit User Number + 6-digit User Password + 6-digit User
Password Example: To add User Number 005 with User Password 123456, press: ## + Master
Password + #** + 005 + 123456 + 123456
Adding a User Password
Deleting a User Password
Press: ## + Master Password + *#* + 3-digit User Number + 3-digit User Number
Changing a User Password
Press: ## + User Password to be changed + *** + New User Password + New User Password
Enabling Passage Function (Press any key to open thedoor)
Press: ## + Master Password + ### + ###
Disabling Passage Function
(keeps door inLOCKED state; opened with valid UserPasswords)
Press: ## + Master Password + ### + ###
USERS-ToOpen the Lock
Press: User Password. After green light goes ON, press lever or rotate knob to open
door within 5 seconds.
In case of loss of user records or other need to RESET all
passwords
Dismantle the Keypad Lock assembly. Press the RESET button on the inside of the
Exterior Panel.
Lock will return to factory set Master Code. Change to new Master Code. Program all
new User Numbers and User Passwords as listed above.
Page.7 Page.8
R
Table of contents
