Detecto VET330WH User manual

I
MODEL VET-330WH
Digital Veterinary and
General Purpose Scale
Owner’s Manual

II

1961-M045-O1 Rev B yVET-330WH Owner’s Manual I
PROPER DISPOSAL
When this device reaches the end of its useful life, it must be properly disposed of. It must
not be disposed of as unsorted municipal waste. Within the European Union, this device
should be returned to the distributor from where it was purchased for proper disposal. This
is in accordance with EU Directive 2002/96/EC. Within North America, the device should be
disposed of in accordance with the local laws regarding the disposal of waste electrical and
electronic equipment.
It is everyone’s responsibility to help maintain the environment and to reduce
the effects of hazardous substances contained in electrical and electronic
equipment on human health. Please do your part by making certain that the
device is properly disposed of. The symbol shown to the right indicates that
this device must not be disposed of in unsorted municipal waste programs.
FCC COMPLIANCE STATEMENT
This equipment generates, uses, and can radiate radio frequency and if not installed and
used in accordance with the instruction manual, may cause interference to radio
communications. It has been designed within the limits for a Class A computing device
pursuant to Subpart J of Part 15 of FCC rules to provide reasonable protection against such
interference when operated in a commercial environment. Operation of this equipment in a
residential area may cause interference in which case the user will be responsible to take
whatever measures necessary to correct the interference.
You may find the booklet "How to Identify and Resolve Radio-TV Interference Problems"
prepared by the Federal Communications Commission helpful. It is available from the U.S.
Government Printing Office, Washington, D.C. 20402. Request stock No. 001-000-00315-4.
COPYRIGHT
All rights reserved. Reproduction or use, without expressed written permission, of editorial
or pictorial content, in any manner, is prohibited. No patent liability is assumed with respect
to the use of the information contained herein.
DISCLAIMER
While every precaution has been taken in the preparation of this manual, the Seller
assumes no responsibility for errors or omissions. Neither is any liability assumed for
damages resulting from the use of the information contained herein. All instructions and
diagrams have been checked for accuracy and ease of application; however, success and
safety in working with tools depend to a great extent upon the individual’s accuracy, skill,
and caution. For this reason, the Seller is not able to guarantee the result of any procedure
contained herein. Nor can they assume responsibility for any damage to property or injury
to persons occasioned from the procedures. Persons engaging in the procedures do so
entirely at their own risk.

1961-M045-O1 Rev B yVET-330WH Owner’s Manual
II

1961-M045-O1 Rev B yVET-330WH Owner’s Manual III
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1
SETUP AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
Install the Scale Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
Transporting the Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
Page 3
Lowering Scale from Transport Position to Floor . . . . . . . . . . . . . . . . . . . . . . . .
.
Page 3
Lifting Scale from Floor to Transport Position . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
Storing the Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
Placing the Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
Placing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4
Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4
Desk Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5
AC Power Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5
Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5
Low Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5
Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5
DISPLAY SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6
KEY FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
Page 9
GRAVITY COMPENSATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 10
DISPLAY MESSAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
CARE AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11
PRECAUTIONS
Before using this instrument, read this
manual and pay special attention to all
"WARNING" symbols:
IMPORTANT ELECTRICAL
WARNING
Serial Number _____________________
Date of Purchase ___________________
Purchased Form ___________________
__________________________________
__________________________________
RETAIN THIS INFORMATION FOR FUTURE USE

1961-M045-O1 Rev B yVET-330WH Owner’s Manual 1
INTRODUCTION
Thank you for purchasing our Detecto Model VET-330WH Digital Veterinary and General
Purpose Scale. The VET-330WH is equipped with a rechargeable battery pack that (after
14 hours of charging) can provide approximately 8 hours of continuous use.
This manual will guide you through the setup and operation of your scale. Please read it
thoroughly before attempting to operate this scale and keep it available for future reference.
SPECIFICATIONS
Capacity: 330 lb x 0.2lb (150 kg x 100 g)
Platform Dimensions: 36 in W x 22 in D x 1.97 in H (90 cm W x 55 cm D x 5 cm H)
Display Dimensions: 10.63 in W x 3.54 in D x 1.77 in H
(270 mm W x 90 mm D x 45 mm H)
Weight Display: Seven-Digit with decimal, seven-segment, 1.0-inch (25 mm) LCD
Power Requirements: Built-in rechargeable battery pack 7.2V DC/1200mA (Cardinal P/N
6800-1067) or the included 120 to 230V AC 15V DC 300 mA
multi-Blade input wall plug-in UL/CUL listed AC power adapter
(Cardinal P/N 6800-1044)
Construction: Stainless steel
Tare: 100% of scale capacity
Keys: HOLD, UNIT, ON/ZERO/OFF, TARE
Operating
Environment: Temperature Range: 40 to 105 °F (+5 to +35 °C) Humidity: 25% ~95% RH
Net Weight: 40 lbs (18 kg)
Shipping Weight: 50 lbs (23 kg)
FEATURES
xStainless steel enclosure for durability and easy wipe-down cleaning
xBuilt-in wheels and carrying handle for easy transportation of scale to a new location
x7.0 ft (2.1 m) cable from scale base to display allows placing the display wherever
it’s easiest to operate keypad and read weight
xIncluded wall or desk mount display bracket and mounting hardware
xMinimal assembly required (install non-skid feet and mounting bracket to display)
xRechargeable battery with low battery indicator
xIncludes an AC power adapter to power scale and charge battery
xSelectable Auto Shut-Off feature (up to 5 minutes) turns the scale off when not used
xZero is established on power up routine and maintained by auto-zero circuitry
xHOLD key allows the animal's weight to be retained after leaving the platform

1961-M045-O1 Rev B yVET-330WH Owner’s Manual
2
SETUP AND INSTALLATION
Unpacking
Before beginning the installation of your scale, make certain the instrument has been
received in good condition. When removing the scale from its packing, inspect it for signs of
damage, such as exterior dents and scratches. Keep the carton and packing material for
return shipment if it should become necessary. It is the responsibility of the purchaser to file
all claims for any damages or loss incurred during transit. Remove all plastic wrapping,
foam fillers, and cardboard material from the scale platform, display, and other components.
You should have the following components:
(1) Scale Platform (with attached Display)
(1) Stainless Steel Platform Cover
(1) Wall or Desk Display Mounting Bracket
(1) 15V DC 300 mA AC power adapter
(1) Hardware Pack, containing:
(2) Screws and Plastic Wall Anchors
(2) Display Bracket Enclosure Knobs
(4) Non-skid Scale Feet
Install the Scale Feet
1. Remove the four leveling feet from the
hardware pack and install one in each
corner of the bottom of the scale base
assembly.
IMPORTANT! THE LEVELING
FEET MUST BE INSTALLED TO
OPERATE THE SCALE.
2. For best results, place the scale on a flat
level surface and adjust the leveling feet
to ensure the scale is sitting level.
3. The scale is now ready for use.
Levelin
g
Feet
Levelin
g
Feet

1961-M045-O1 Rev B yVET-330WH Owner’s Manual 3
SETUP AND INSTALLATION, CONT.
Transporting the Scale
The VET-330WH has built-in wheels and an integral carrying
handle for easy transportation of the scale to a new location.
Follow the instructions below to safely lower and raise the
scale to and from the floor when relocating the scale.
DO NOT DROP THE SCALE! This scale weighs
approximately 50 pounds. Damage to the Load Cells
can occur if the scale is dropped or allowed to fall
from the transport position. If damage to scale is
determined to have been caused by falling or
dropping scale, the warranty will be voided!
Lowering Scale from Transport Position to Floor
1. From the transport position, stand close to the scale with
your feet 8 to 12 inches apart.
2. Firmly grasp the handle on the scale.
3. While stepping back, lower the scale to the floor, keeping
your back straight and bending your knees until you're in a
squatting position.
Never bend at the waist with your legs straight!
Lifting Scale from Floor to Transport Position
1. Stand close to the scale with your feet 8 to 12 inches apart.
2. Keeping your back straight, bend your knees until you're in
a squatting position.
Never bend at the waist with your legs straight!
3. Firmly grasp the handle on the scale and lift it straight up.
Don't twist to either side. Keep the scale close to you, not
at arm's length.
4. Use your leg muscles as you lift, keeping your back upright
and in its natural posture. Always lift steadily and smoothly without jerking.
Storing the Scale
For storage, lay the scale flat for maximum protection against damage.
Placing the Scale
The scale should be placed on a flat, level floor or low-cut carpet away from any rapidly
moving air source (heating and cooling vents). Check to make certain the scale is level. If it
is not, adjust all four (4) feet as required to attain a level scale.
NOTE: Any time the scale is moved or re-located, be sure to check if the scale is
level before using it.
Scale Transport Position

1961-M045-O1 Rev B yVET-330WH Owner’s Manual
4
SETUP AND INSTALLATION, CONT.
Placing the Display
The VET-330WH display has a 7.0 ft (2.1 m) cable to allow it to be placed at a convenient
position away from the scale base. The included bracket can be used to mount the display
on a wall or it can be used to place it on a desk or table for easy viewing.
Wall Mounting
1. Choose the location to mount the display on the wall where it can be easily viewed, not
subject to direct sunlight, and where the keypad is within easy reach of the operator.
2. Using the bracket for a template, place the bracket against the wall and mark the holes
to mount it. Remove the bracket and drill two (2) 13/64 in (5 mm) holes in the wall for the
mounting wall anchors.
Use the mounting bracket as a template to mark holes to drill.
3. Insert the wall anchors in the wall until they are flush with
the wall.
4. Insert the two (2) M3.0x25 screws into the wall anchors,
and then tighten them until there is approximately 1/8”
(3 mm) gap between the screw head and the anchor.
5. Place the display in the bracket and install the included enclosure knobs. Adjust the
angle of the display for the best viewing, and then completely tighten the knobs.
Place the display in the mounting
bracket and install the enclosure knobs. Adjust display for viewing angle and completely
tighten enclosure knobs.
6. Place the large end of the slotted holes in the bracket over the screw heads, and gently
pull down to secure the bracket and display to the wall.
Leave 1/8” (3 mm) gap between
screw head and wall anchor.

1961-M045-O1 Rev B yVET-330WH Owner’s Manual 5
SETUP AND INSTALLATION, CONT.
Desk Mounting
1. The location chosen should be a stable, level surface (either a desk or solid table),
free of temperature extremes and water. The display should be where it can be easily
viewed, not subjected to direct sunlight, and where the keypad is within easy reach of
the operator.
2. Place the display in the bracket and install the included enclosure knobs. Adjust the
angle of the display for the best viewing, and then completely tighten the knobs. Refer to
the image for Step 5 in the Wall Mounting instructions on the previous page.
AC Power Adapter
To apply power to the scale using the
supplied 120 to 230V AC 15V DC 300 mA
wall plug-in UL/CUL listed AC power
adapter (Cardinal P/N 6800-1044), insert
the plug from the power adapter cable
into the power jack on the right side of the
display (as viewed facing the display) and
then plug AC power adapter into the
proper electrical outlet. The scale is now
ready for operation.
Battery Pack
The VET-330WH scale uses a 7.2V DC, 1200 mA built-in rechargeable battery pack
(Cardinal P/N 6800-1067). The VET-330WH can operate for approximately 8 hours of
continuous use with a fully charged battery pack.
Low Battery Indicator
When the battery pack needs to be recharged, a low battery indicator on the
display will turn on. If the battery voltage drops too low for accurate weighing,
the scale will automatically shut off and you will be unable to turn it back on.
Battery Charging
When the low battery indicator is displayed, the operator should plug the AC power adapter
into the scale display and then into the proper electrical wall outlet. To fully recharge the
battery pack, the AC power adapter must be connected for approximately 14 hours. Note
that the VET-330WH can still be operated while the battery pack is charging. Also, note that
charging the battery pack for more than 14 hours will not damage it.
NOTE: If the AC power adapter is disconnected before the 14 hours, the scale will continue
to charge the battery pack when the AC power adapter is plugged back in.
A
C Power
A
dapter Plug
AC Power Adapte
r

1961-M045-O1 Rev B yVET-330WH Owner’s Manual
6
DISPLAY SYMBOLS
The display symbols are turned on to indicate that the scale display is in the mode
corresponding to the symbol or that the status indicated by the symbol is active.
{
{
(STABLE)
This symbol is turned on when the weight display is stable.
(NEGATIVE)
This symbol is turned on to indicate the displayed weight is a negative weight.
t{s
(ZERO)
This symbol is turned on to indicate that the weight display is at center-of-zero.
This symbol is turned on to indicate the battery pack needs to be recharged.
(HOLD)
The arrow symbol is turned on and will flash after pressing the HOLD key to indicate
that the Hold function is On.
NOTE: The arrow symbol will stop flashing when the weight on the scale is above 3.3 lb
(1.5 kg) and stable, or the HOLD key is pressed again to turn off the Hold function. Note
that pressing the TARE key will also turn off the Hold function.
kgThis symbol is turned on to indicate that the displayed weight is in kilograms.
lb This symbol is turned on to indicate that the displayed weight is in pounds.

1961-M045-O1 Rev B yVET-330WH Owner’s Manual 7
KEY FUNCTIONS
HOLD
1. Press this key to turn the Hold function on. The arrow symbol will turn on and will
flash to indicate that the Hold function is on.
NOTE: The arrow symbol will stop flashing when the weight on the scale is above
3.3 lb (1.5 kg) and stable.
2. To turn off the Hold function, press the HOLD key again or press the TARE key.
3. In the Configuration Mode, press this key to confirm the setting for each menu.
UNIT
1. Press to change the weighing units to the alternate units of measurement (must be
selected in the Configuration Mode).
2. In the Configuration Mode, press this key to select the menu.
ON/ZERO/OFF
1. When the scale is off, press and release this key to turn the scale on.
2. If the scale is already on, press and release this to turn the scale off.
3. If the weight display is not at zero, press this key to reset the display to zero (. ).
NOTE: A maximum of up to 20% of the scale capacity can be zeroed.
TARE
1. Press this key to tare (zero) the weight of a container (e.g., a box, pet carrier, or
travel cage) up to the full capacity of the scale.
2. When the Hold function is on, pressing this key will also turn the Hold function off.
3. Press and hold this key for three (3) seconds to enter the Configuration mode.
DO NOT operate the keypad with pointed objects (pencils, pens, etc.).
Damage to the keypad resulting from this practice is NOT covered under the
warranty.

1961-M045-O1 Rev B yVET-330WH Owner’s Manual
8
OPERATION
Turn the Scale On
Press the ON/ZERO/OFF key to turn the scale on. The scale will display
 then change to the selected weighing units.
Select the Weighing Unit
Press the UNIT key to alternate between the selected weighing units. NOTE: The
alternate weighing units must be enabled in the Configuration Mode for this function to
be operational.
Basic Weighing
Place the pet or animal to be weighed on the scale platform. Wait a moment for the
scale display to stabilize, then read the weight.
Zero the Weight Display
If the scale is not showing zero weight on the display, press the ZERO key. The weight
display will return to zero (. ) with the t{s(Zero) and {(Stable) symbols turned.
NOTE: The scale can be re-zeroed to a maximum of up to 20% of the scale capacity.
Tare the Weight Display
Place the container (e.g., a box, pet carrier, or travel cage) on the scale platform, allow
the scale to stabilize, and then press the TARE key. The weight on the scale can be
tared (zeroed off) until the full capacity of the scale is reached. Note that when removing
the container from the scale platform, the scale will display negative weight.
To clear a tare weight, press the TARE key with the scale platform empty. This will reset
the weight display to zero.
Hold the Displayed Weight
To hold the displayed weight of the pet or animal, press the HOLD key. The arrow
symbol is turned on and will flash to indicate the Hold function is on. Place the pet or
animal on the scale. When the weight on the scale is above 3.3 lb (1.5 kg) and stable,
the arrow will stop flashing and the displayed weight will be held.
The weight on the display will be held until the HOLD key is pressed again or the TARE
key is pressed to turn off the Hold function.
Turn the Scale Off
With the scale turned on, press the ON/ZERO/OFF key to turn the scale off.

1961-M045-O1 Rev B yVET-330WH Owner’s Manual 9
CONFIGURATION
The VET-330WH scale has been pre-configured at the factory and should not require
changes to use in most applications. If the factory settings do not meet the requirements of
your application, the following describes the steps to change the configuration of the scale.
To Begin Configuration:
1. Press the ON/ZERO/OFF key to turn on the scale.
2. Press and hold the TARE key for 3 seconds.
3. When the display shows *4;, release the TARE key. The scale will enter the
Configuration mode with the display showing '0-;.
Weighing Units
To select “kg” (kilogram) weighing units:
1. With the display showing '0-;, press the HOLD key. The display will change to
show “kg”.
2. Press the HOLD key to display kg status.
3. Press the UNIT key to toggle between:
Enable (display will change to #0) or
Disable (display will change to #).
4. Press the HOLD key. The display will change to '0-;.
5. Proceed to Automatic Shutoff.
To select “lb” (pounds) weighing units
1. With the display showing '0-;, press the HOLD key and then the UNIT key. The
display will change to show “lb”.
2. Press the HOLD key to display lb status.
3. Press the UNIT key to toggle between:
Enable (display will change to #0) or
Disable (display will change to #).
4. Press the HOLD. The display will change to '0-;.
5. Proceed to Automatic Shutoff.
Automatic Shutoff
1. With the display showing '0-;, press the press UNIT key. The display will change
to show #.
2. Press the HOLD key to begin the selection of the automatic shut-off time (in
seconds). The display will change to show .
3. Press the UNIT key to toggle through the selections, , , , , or #.
4. When the desired time is displayed, press the HOLD key. The display will change to
show #.
5. Proceed to Gravity Compensation.

1961-M045-O1 Rev B yVET-330WH Owner’s Manual
10
CONFIGURATION, CONT.
Gravity Compensation
1. With the display showing #15, press the press UNIT key 4 times. The display will
change to show %'.
2. Press the HOLD key.
To Enable the Gravity Compensation mode, press the UNIT key. The display will
change to #0.
To Disable the Gravity Compensation mode, press the UNIT key. The display will
change to #.
3. Press the HOLD key again. The display will change to show 9<.
4. Press the UNIT key. The display will change to show 03.
5. Press the HOLD key to save the settings and reset the scale.
6. The setup is complete.
GRAVITY COMPENSATION
The Gravity Compensation for your VET-330WH scale has been pre-configured at the
factory and should not require changing in most locations. If the factory settings do not
meet the requirements of your location, contact the factory for the value for your location.
With 9< enable from the function setting of the Configuration mode, the scale will use
the factory-set value of 9.796 for the Gravity Compensation.
If the 9< is disabled, the scale will use the value obtained from the factory and
entered by the operator for the Gravity Compensation.
To Change the Gravity Compensation Value:
1. Press the ON/OFF key to turn on the scale.
2. Press and hold the UNIT key for 3 seconds to enter the Gravity Compensation mode,
the display will show 9.796 (or the current value).
3. Enter the desired gravity value (press the UNIT key to choose a number from 0~9,
and press the HOLD key to move to the right digit.
4. Press the TARE key (to confirm the entered gravity) and return the scale to the
normal operating mode.

1961-M045-O1 Rev B yVET-330WH Owner’s Manual 11
DISPLAY MESSAGES
The VET-330WH scale is equipped with software that tests various portions of the scale's
circuitry and verifies proper operation. Should a problem be detected, a message will be
displayed alerting the operator to that condition. The following lists the messages displayed
and their meaning:
DISPLAY MEANING
This symbol is displayed when the battery pack needs to
be recharged. NOTE: If the battery voltage drops too low
for accurate weighing, the scale will automatically shut off
and you will be unable to turn it back on.
99` This error will be displayed if the E2PROM has some
problem. Please consult your scale service
representative.
99!` The Zero count is too low. Please consult your scale
service representative.
99` This error is display when the weight on the scale
exceeds the scale capacity. Remove the weight to clear
the error.
This error can also be displayed if the Zero count is too
high. Please consult your scale service representative.
CARE AND MAINTENANCE
The heart of the VET-330WH Digital Veterinary and General Purpose Scale is four
precision load cells located in each corner of the scale base. It will provide accurate
operation indefinitely if protected against overload of scale capacity, dropping items on the
scale, or other extreme shocks.
xDO NOT submerge scale or display in water, pour or spray water directly on them.
xDO NOT use acetone, thinner, or other volatile solvents for cleaning.
xDO NOT expose scale or display to direct sunlight or temperature extremes.
xDO NOT place the scale in front of heating/cooling vents.
xDO clean scale and display with a damp soft cloth and mild non-abrasive detergent.
xDO remove power before cleaning with a damp cloth.
xDO provide clean AC power and adequate protection against lightning damage.
xDO keep surroundings clear to provide clean and adequate air circulation.

1961-M045-O1 Rev B yVET-330WH Owner’s Manual
12
STATEMENT OF LIMITED WARRANTY
Detecto Scale warrants its equipment to be free from defects in
material and workmanship as follows: Detecto warrants to the
original purchaser only that it will repair or replace any part of
equipment which is defective in material or workmanship for a
period of two (2) years from date of shipment. Detecto shall be
the sole judge of what constitutes a defect.
During the first ninety (90) days Detecto may choose to
replace the product at no charge to the buyer upon inspection of
the returned item.
After the first ninety (90) days, upon inspection of the returned
item, Detecto will repair or replace it with a remanufactured
product. The customer is responsible for paying for the freight
both ways.
This warranty does not apply to peripheral equipment not
manufactured by Detecto; this equipment will be covered by
certain manufacturer’s warranty only.
This warranty does not include replacement of expendable or
consumable parts. This does not apply to any item which has
deteriorated or damaged due to wear, accident, misuse, abuse,
improper line voltage, overloading, theft, lightning, fire, water or
acts of God, or due to extended storage or exposure while in
purchaser’s possession. This warranty does not apply to
maintenance service. Purchased parts will have a ninety (90)
day repair or replacement warranty only.
Detecto may require the suspect product to be returned to the
factory; item(s) must be properly packed and shipping charges
prepaid. A return authorization number must be obtained for all
returns and marked on the outside of all returned packages.
Detecto accepts no responsibility for loss or damage in transit.

1961-M045-O1 Rev B yVET-330WH Owner’s Manual 13
STATEMENT OF LIMITED WARRANTY
Conditions Which Void Limited Warranty
This warranty shall not apply to equipment which:
A.) Has been tampered with, defaced, mishandled or has had
repairs and modifications not authorized by Detecto.
B.) Has had serial number altered, defaced, or removed.
C.) Has not been grounded according to Detecto’s
recommended procedure.
Freight Carrier Damage
Claims for equipment damaged in transit must be referred to the
freight carrier in accordance with freight carrier regulations.
This warranty sets forth the extent of our liability for breach of
any warranty or deficiency in connection with the sale or use of
the product. Detecto will not be liable for consequential damages
of any nature, including but not limited to, loss of profit, delays or
expenses, whether based on tort or contract. Detecto reserves
the right to incorporate improvements in material and design
without notice and is not obligated to incorporate improvements
in equipment previously manufactured.
The foregoing is in lieu of all other warranties, express or implied
including any warranty that extends beyond the description of
the product including any warranty of merchantability or fitness
for a particular purpose. This warranty covers only those Detecto
products installed in the forty-eight (48) contiguous continental
United States.
Ph. [phone]
E-mail: [e-mail]
203 E. Daugherty
Webb City, MO 64870
08/27/2014
Printed in USA
D268-WARRANTY-DET-A

1961-M045-O1 Rev B yVET-330WH Owner’s Manual
14
Cardinal Scale Manufacturing Co.
102 E. Daugherty, Webb City, MO 64870 USA
Ph: 417-673-4631 or 1-800-641-2008
Fax: [phone]
Technical Support: 1-866-254-8261
E-mail: [e-mail]
1961-M045-O1 Rev B 07/21