DFI VC900-M8M User manual

07320
CT-11-03 Rev 6Page 1 of 3
NSAI, 1 Swift Square, Northwood, Santry, Dublin 9, Ireland. Telephone: (+353+1) 807 3800, Facsimile: 01-807 3844
ECE TYPE-APPROVAL CERTIFICATE
Communication Concerning:2Approval granted
Approval extended
Approval refused
Approval withdrawn
Production definitively discontinued
Of a type of vehicle/component/separate technical unit2with regard to Regulation No. 10.
Of a type of electrical/electronic sub-assembly2with regard to Regulation No.10.
Approval No: E24*10R06/02*4590*00
Reason for extension: -N/A
1. Make (trade name of manufacturer): DFI, ITOX
2. Type and general commercial description: VC900-M8M
Embedded System
Variant(s): Variant A: VC900-M8M
Variant B: VC900-M8M????????????
3. Means of identification of type, if marked on the vehicle/
component/separate technical unit2: Variant designation
3.1 Location of that marking: On the back of the unit
4. Category of vehicle: N/A
5. Name and address of manufacturer: DFI Inc.
10F., No. 97, Sec. 1, Xintai 5th Rd., Xizhi
Dist., New Taipei City 22175, Taiwan
6. In the case of components and separate technical units,
location and method of affixing of the approval mark: Label affixed on the back of the unit
7. Address(es) of assembly plant(s): DFI Inc.
No.157, Shanying Rd., Gueishan Dist.,
Taoyuan City 333424, Taiwan

07320
CT-11-03 Rev 6Page 2 of 3
NSAI, 1 Swift Square, Northwood, Santry, Dublin 9, Ireland. Telephone: (+353+1) 807 3800, Facsimile: 01-807 3844
Approval No: E24*10R06/02*4590*00
8. Additional information (where applicable): See appendix below
9. Technical service responsible for carrying out the tests: SGS-TUV Saar GmbH
Am TUV 1 D-66280 Sulzbach
10. Date of test report: 28.03.2023
11. Number of test report: TMXD2301000248DV
12. Remarks (if any): See Appendix below
13. Place: Dublin
14. Date: 15th May, 2023
15. Signature:
16. The index to the information package lodged with the approval authority, which may be obtained on
Request, is attached.
__________________________
1. Distinguishing number of the country which issued/extended/refused or withdrawn approval.
(see Regulation, provisions on approval).
2. Strike out what does not apply.

07320
CT-11-03 Rev 6Page 3 of 3
NSAI, 1 Swift Square, Northwood, Santry, Dublin 9, Ireland. Telephone: (+353+1) 807 3800, Facsimile: 01-807 3844
Approval No: E24*10R06/02*4590*00
Appendix
To type-approval communication concerning the type approval
of an electrical/electronic sub-assembly under Regulation No.10.
1. Additional information
1.1. Electrical system rated voltage: DC 12/24V, negative ground
1.2. This ESA can be used on any vehicle type with the
following restrictions: See manufacturer’s specifications.
1.2.1 Installation conditions, if any: See manufacturer’s specifications.
1.3. This ESA can only be used on the following vehicle types: N/A
1.3.1 Installation conditions, if any: N/A
1.4. The specific test method(s) used and the frequency ranges
covered to determine immunity were: N/A
1.5. Laboratory accredited to ISO 17025 and recognized by the Approval
Authority responsible for carrying out the tests: SGS-TUV Saar GmbH
2. Remarks: N/A
Appendix to type-approval communication concerning the
type approval of a vehicle under Regulation No.10.
1. Additional information
2. Electrical system rated voltage: N/A
3. Type of bodywork: N/A
4. List of electronic systems installed in the tested vehicle(s)
not limited to the items in the information document: N/A
4.1. Vehicle equipped with 24 GHz short-range radar equipment
(yes/no/optional)2: N/A
5. Laboratory accredited to ISO 17025 and recognized by the Approval
Authority responsible for carrying out the tests: N/A
6. Remarks: N/A

07320
Page 1 of 2
NSAI, 1 Swift Square, Northwood, Santry, Dublin 9, Ireland. Telephone: (+353+1) 807 3800, Facsimile: 01-807 3844
Approval No: E24*10R06/02*4590*00
Index to the Information Package
Date of issue: 15th May, 2023
Date of latest amendment: N/A
Reason for extension/revision: N/A
1. Additional conditions, and advisory
notes on legal alternatives.
2. Test report(s)
- numbers(s): TMXD2301000248DV
- date of issue: 28.03.2023
- date of latest amendment: N/A
3. Information document
- number(s): IF_TMXD2301000248DV
- date of issue: 28.03.2023
- date of latest amendment: N/A
Documentation: 175 pages

07320
Page 2 of 2
NSAI, 1 Swift Square, Northwood, Santry, Dublin 9, Ireland. Telephone: (+353+1) 807 3800, Facsimile: 01-807 3844
Approval No: E24*10R06/02*4590*00
Appendix: Additional conditions, and advisory notes on legal alternatives
A: Additional conditions:
1. The attached technical report, with any of its attachments, forms part of this Type Approval certificate.
2. Each device from series production shall be to the measurements specified in the attached drawings, and shall
be manufactured only from the materials specified in the Approval documents.
3. Changes in the type are permitted only with the explicit permission of NSAI. Breaches of this requirement will
lead to a withdrawal of the Type Approval, and in addition may be subject to criminal prosecution.
4. At regular intervals, any tests or associated checks prescribed by the applicable legislation to verify continued
conformity with the approved type shall be carried out. The manufacturer shall demonstrate compliance with
this by submitting to NSAI evidence of adequate arrangements and documented control plans for each type
approved.
5. Any set of samples or test pieces showing evidence of non-conformity shall give rise to further sampling and
testing and all steps shall be taken to restore conformity of production.
6. This Type Approval will expire when it is surrendered by the holder, or withdrawn by NSAI, or when the
approved type no longer conforms to legal requirements. The recall of the Type Approval can be issued by NSAI
when the conditions required for the issuing or continuation of the Type Approval are no longer current, or when
the Approval holder is in breach of the duties attached to the Type Approval, or when it is established that the
approved type no longer meets the requirements of traffic safety.
7. Changes in the company name, address or manufacturing site, as well as in any of the sales or other agents
specified in the issuing of the approval must immediately be notified to NSAI.
8. The duties imposed by the issuing of this certificate are not transferable. The legal protection of third parties is
not affected by this certificate.
9. When the manufacture or sale of the system, component or separate technical unit has not been started within
one year of the date of issue of this certificate, then NSAI is to be informed. This requirement also applies when
the manufacture or sale has been halted for more than one year, or when it ought to have been halted for more
than one year. The initial commencement of manufacture or sale, or the resumption of
manufacture or sale, shall then be notified to NSAI within one month of commencement or resumption.
B: Legal Options:
Any objection to the requirements set out in this certificate shall be made within one month of the date of issue.
The objection shall be made, in writing, to NSAI in Dublin.

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Page / Seite
1 of / von 4
Technical Report / Technischer Bericht
V00
Test standard / Prüfgrundlage:
UN-R 010
Level of amendment / Änderungsstand:
06 Series of Amendments, Supplement 2
Title / Titel
Electromagnetic compatibility
Manufacturer / Hersteller:
DFI Inc.
Type / Typ:
VC900-M8M
Subject of testing / Gegenstand der Prüfung:
Component
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Page / Seite
2 of / von 4
0
General / Allgemeine Angaben:
0.1
Make
(trade name of manufacturer) /
Fabrikmarke
(Firmenname des Herstellers):
DFI, ITOX
0.2
Type /
Typ:
VC900-M8M
Variant A: VC900-M8M
Variant B: VC900-M8M????????????
(? = A ~ Z, a ~ z, 0 ~ 9, -, blank, or any
character)
Explanation: for marketing purpose only
0.2.1
Commercial description(s) /
Handelsname(n):
Embedded System
0.3
Means of identification of type, if
marked on the vehicle / component /
technical unit /
Merkmale zur Typidentifizierung,
sofern am Fahrzeug / Bauteil / an
der selbständigen technischen
Einheit vorhanden:
Variant designation
0.3.1
Location of that markings /
Anbringungsstelle dieser Merkmale:
On the back of the unit
0.4
Category of vehicle /
Fahrzeugklasse:
-
0.5
Manufacturer's name and address /
Name und Anschrift des Herstellers:
DFI Inc.
10F., No. 97, Sec. 1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 22175, Taiwan
0.8
Address of assembly plant /
Name(n) und Anschrift(en) der
Fertigungsstätte(n):
DFI Inc.
No.157, Shanying Rd., Gueishan Dist.,
Taoyuan City 333424, Taiwan
0.9
Name and address of
representative /
Name und Anschrift des
Beauftragten:
-
0.10
Location of the approval mark /
Anbringungsstelle des
Genehmigungszeichens:
Label affixed on the back of the unit
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Page / Seite
3 of / von 4
1
Appendices / Anhänge:
1.1
Test record / Prüfprotokoll:
See appendix A /
Siehe Anhang A
-
1.2
List of modifications /
Liste der Änderungen
See appendix B /
Siehe Anhang B
n.a.
2
Attachments / Anlagen:
2.1
Information folder /
Beschreibungsmappe:
No. / Nr.: IF_TMXD2301000248DV
Date of issue /
Ausgabedatum: 28.03.2023
2.2
Further enclosures
Sonstige Anlagen
Test report / Prüfbericht:
No. / Nr.: TRS_TMXD2301000248DV
Date of issue /
Ausgabedatum: 28.03.2023
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Page / Seite
4 of / von 4
3
Statement of conformity / Schlussbescheinigung:
The information folder as mentioned under no. 2.2 and the type described therein are in
compliance with the test standard mentioned above. With regard to the required level of
performance to be achieved, the test specimen were representative for the type to be
approved. /
Die unter Nr. 2.2 angegebene Beschreibungsmappe und der darin beschriebene Typ
entsprechen der oben aufgeführten Prüfgrundlage. Die verwendeten Prüfmuster
waren im Hinblick auf das erforderliche Leistungsniveau für den zu genehmigenden Typ
repräsentativ.
The tests were carried out in accordance to the relevant requirements of the
Die Durchführung der Prüfungen entsprach den relevanten Anforderungen der
☐EN ISO/IEC 17025 EN ISO/IEC 17020
Test Laboratory / Prüflaboratorium
SGS-TÜ V Saar GmbH
notified by
benannt durch
Kraftfahrt-Bundesamt (KBA),
Federal Republic of Germany
No. KBA - P 00084 –10
National Standards
Authority of Ireland (NSAI)
No. 101
Rijksdienst voor het Wegverkeer
(RDW),
The Netherlands
No. 99050064 00
Formal Review (Conformity Check) by /
Konformitätsprüfung durch diger
Authorized by the Responsible expert /
Verantwortlicher Sachverstän
Victor Wen
Calvin Tzou
Taipei, 28.03.2023
This Technical Report shall be reproduced and published in full only and by the client only. It shall be repro-duced partially with the written
permission of the Test Laboratory only.
This document is issued by the Company subject to its General Conditions of Service (www.sgsgroup.de/agb). Attention is drawn to the
limitations of liability, indemnification and jurisdictional issues established therein. This document is an original. If the document is submit-
ted digitally, it is to be treated as an original within the meaning of UCP 600. Any holder of this document is advised that information
contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this
document is unlawful and offenders may be prosecuted to the fullest extent of the law.
To assess the conformity, the laboratory refers to the “scope classification” of the Kraftfahrt-Bundesamt (KBA) –Federal Motor
Transport Authority (in its valid version at the time of testing) and the specified consideration of the measurement uncertainty for the
related test procedure.
In case the measurement uncertainty does not need to be considered according to the scope classification, the laboratory considers the
result conform if its measured value is within the specification.
In case the measurement uncertainty does need to be considered according to the scope classification, the laboratory considers the result
conform if its value incl. its measurement uncertainty is within the specification.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
1 of / von 17
Test record / Prüfprotokoll
1
Test conditions / Prüfbedingungen
1.1
Test component / Geprüftes Bauteil
1.1.1
Function description / Funktionsbeschreibung
Embedded System
1.1.2
Type / Typ
VC900-M8M
1.1.3
ESA(s) / variants
Variant A: VC900-M8M
1.1.4
Tested operating mode(s) / geprüfte(r)
Betriebszustand(-zustände)
See test report of the enclosure./
Siehe Prüfbericht in der Anlage.
1.1.5
Tested rated voltage(s) / geprüfte
Nennspannung(en)
12 V / 24V
1.1.6
The approval object is … / Bei dem
Genehmigungsobjekt handelt es sich um …
an ESA that is not related to a connection
system for charging a REESS / eine EUB, die
nicht im Zusammenhang mit einem An-
schlusssystem zum Laden eines REESS
steht
X
yes / ja
no / nein
a complete connection system for charging a
REESS / ein vollständiges Anschlusssystem
zum Laden eines REESS
yes / ja
X
no / nein
a component of a connection system for
charging a REESS / eine Komponente eines
Anschlusssystems zum Laden eines REESS
yes / ja
X
no / nein
Have the HV voltages and HV currents been
taken into account in the tests and measure-
ments? / Wurden die HV-Spannungen und
HV-Ströme bei den Prüfungen bzw.
Messungen berücksichtigt?
yes / ja
no / nein
X
n.a.
a light source or a part of a light source acc.
to item 3.2.10 of the Regulation / Handelt es
sich um ein Gerät, das die Anforderungen
des Punktes 3.2.10 der Regelung erfüllt?
(Beleuchtung)
yes / ja
X
no / nein
Approval number or number of test report /
Genehmigungsnummer oder Nummer des
Prüfberichts
X
n.a.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
2 of / von 17
1.1.7
Do the devices of the type have immunity
related functions? / Haben die Geräte des
Typs Funktionen im Zusammenhang mit der
Störfestigkeit?
yes / ja
X
no / nein
Reason if necessary / Ggf. Begründung:
X
n.a.
1.1.8
Do the devices of the type have to be in oper-
ation during the engine start phase? /
Müssen die Geräte des Typs während der
Motorstartphase in Betrieb sein?
yes / ja
X
no / nein
1.1.9
Photo documentation of the examinee includ-
ing existing labels / Fotodokumentation des
Prüflings inkl. vorhandener Aufschriften
See test report of the enclosure./
Siehe Prüfbericht in der Anlage.
1.1.10
Remarks / Bemerkungen:
n.a.
The tested ESA is a DC 12V/24V
device, the energy efficiency in-
vehicle telematics system assists
smart vehicles in collecting data,
including vehicle speed, engine
speed, network packet records, etc.,
and finally uploads them to cloud
storage through 4G synchronously
for daily data analysis and services.
That doesn’t have immunity related
functions.
Variant A: VC900-M8M full test was
performed. Variant B for marketing
purpose only, not affect EMC char-
acteristic, no necessary to perform
test.
1.2
Test equipment / Prüfeinrichtungen
Parameter of the test area / Prüfortparame-
ter:
The equipment, on which the tests
were carried out, fulfilled the require-
ments of the Regulation. /
Die Prüfungen wurden auf Anlagen
durchgeführt, die den Anforderungen
der Regelung entsprechen.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
3 of / von 17
2
Test Results / Prüfergebnisse
2.1
Test results in configurations other than
„REESS charging mode coupled of the power
grid / Prüfergebnisse für andere Konfigura-
tionen als “REESS im Ladebetrieb mit dem
Versorgungsnetz gekoppelt”
X
fulfilled / erfüllt
not fulfilled / nicht erfüllt
n.a.
Remarks / Bemerkungen:
X
n.a.
2.1.1
Measurement of radiated broadband electro-
magnetic emissions from electrical/ electronic
subassemblies according to item 6.5 of the
Regulation /
Messungen von gestrahlten breitbandigen el-
ektromagnetischen Störungen aus elektri-
schen/ elektronischen Unterbaugruppen
gemäß Punkt 6.5 der Regelung:
X
fulfilled / erfüllt
not fulfilled / nicht erfüllt
n.a.
2.1.1.1
Measurement procedure /
Messverfahren:
Quasi-peak-detector
Quasi-Spitzenwert-Detektor
2.1.1.2
Measurement setup /
Messaufbau:
Anechoic chamber
Absorberhalle
2.1.1.3
Measurement results /
Messergebnisse:
The measured values, expressed in
dB µV/m, are below the reference
limits. See test report of the
enclosure./
Die gemessenen Werte bleiben,
ausgedrückt in dB µV/m, unter den
Grenzwerten. Siehe Prüfbericht in
der Anlage.
2.1.1.4
Photo documentation of the measurement
setup (if applicable) /
Fotodokumentation des Messaufbaus (sofern
erforderlich):
See test report of the enclosure./
Siehe Prüfbericht in der Anlage.
2.1.1.5
Remarks / Bemerkungen:
X
n.a.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
4 of / von 17
2.1.2
Measurement of radiated narrowband elec-
tromagnetic emissions from electrical/ elec-
tronic subassemblies according to item 6.6 of
the Regulation /
Messungen von gestrahlten schmalbandigen
elektromagnetischen Störungen aus el-
ektrischen/ elektronischen Unterbau-gruppen
gemäß Punkt 6.6 der Regelung:
X
fulfilled / erfüllt
not fulfilled / nicht erfüllt
n.a.
2.1.2.1
Measurement procedure /
Messverfahren:
Average-detector
Mittelwert-Detektor
2.1.2.2
Measurement setup /
Messaufbau:
Anechoic chamber
Absorberhalle
2.1.2.3
Measurement results /
Messergebnisse:
The measured values, expressed in
dB µV/m, are below the reference
limits. See test report of the
enclosure./
Die gemessenen Werte bleiben,
ausgedrückt in dB µV/m, unter den
Grenzwerten. Siehe Prüfbericht in
der Anlage.
2.1.2.4
Photo documentation of the measurement
setup (if applicable) /
Fotodokumentation des Messaufbaus (sofern
erforderlich):
See test report of the enclosure./
Siehe Prüfbericht in der Anlage.
2.1.2.5
Remarks / Bemerkungen:
X
n.a.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
5 of / von 17
2.1.3
Testing for emission of transient conducted
disturbances of electrical/electronic subas-
semblies on 12/24 V supply lines according
to item 6.7 of the Regulation /
Prüfung der leitungsgeführten Störaus-sen-
dungen von elektrischen/elektronischen Un-
terbaugruppen auf 12/24 V Versorgungslei-
tungen gemäß Punkt 6.7 der Regelung
X
fulfilled / erfüllt
not fulfilled / nicht erfüllt
n.a.
2.1.3.1
Test results /
Prüfergebnisse:
The limits are kept. See test report of
the enclosure./
Die Grenzwerte wurden eingehalten.
Siehe Prüfbericht in der Anlage.
2.1.3.2
Photo documentation of the measurement
setup (if applicable) /
Fotodokumentation des Messaufbaus (sofern
erforderlich):
See test report of the enclosure. /
Siehe Prüfbericht in der Anlage.
2.1.3.3
Remarks /
Bemerkungen:
X
n.a.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
6 of / von 17
2.1.4
Testing for radiated immunity of electrical/
electronic subassemblies to electromagnetic
radiation according to item 6.8 of the Regu-
lation /
Prüfung der gestrahlten Störfestigkeit von
elektrischen/ elektronischen Unterbau-
gruppen gegenüber eingestrahlten elektro-
magnetischen Feldern gemäß Punkt 6.8 der
Regelung:
fulfilled / erfüllt
not fulfilled / nicht erfüllt
X
n.a.
2.1.4.1
Test procedure /
Prüfverfahren:
X
n.a.
2.1.4.2
Test setup /
Prüfaufbau:
X
n.a.
2.1.4.3
Test results /
Prüfergebnisse:
X
n.a.
2.1.4.4
Photo documentation of the measurement
setup (if applicable) /
Fotodokumentation des Messaufbaus (sofern
erforderlich):
X
n.a.
2.1.4.5
Remarks / Bemerkungen:
n.a.
ESA not safety-related according to
item 2.12 of the Regulation. /
EUB nicht sicherheitsrelevant nach
Punkt 2.12 der Regelung.
The tested ESA is a DC 12V/24V
device, the energy efficiency in-
vehicle telematics system assists
smart vehicles in collecting data,
including vehicle speed, engine
speed, network packet records, etc.,
and finally uploads them to cloud
storage through 4G synchronously
for daily data analysis and services.
That doesn’t have immunity related
functions according to item 2.12 of
the Regulation.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
7 of / von 17
2.1.5
Testing for immunity to transient disturbances
conducted along on 12/24 V supply lines of
electrical/electronic subassemblies according
to item 6.9 of the Regulation /
Prüfung der Störfestigkeit gegen leitungsge-
führte transiente Störungen auf 12/24 V Ver-
sorgungsleitungen von elektrischen/ el-
ektronischen Unterbaugruppen gemäß Punkt
6.9 der Regelung:
X
fulfilled / erfüllt
not fulfilled / nicht erfüllt
n.a.
2.1.5.1
Test results /
Prüfergebnisse:
During the test was no unacceptable
degradation. See test report of the
enclosure./
Während der Prüfung trat keine
unzulässige Beeinträchtigung auf.
Siehe Prüfbericht in der Anlage.
2.1.5.2
Photo documentation of the measurement
setup (if applicable) /
Fotodokumentation des Messaufbaus (sofern
erforderlich):
See test report of the enclosure./
Siehe Prüfbericht in der Anlage.
2.1.5.3
Remarks / Bemerkungen:
X
n.a.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
8 of / von 17
2.2
Test results in configurations „REESS charg-
ing mode coupled of the power grid /
Prüfergebnisse für Konfigurationen “REESS
im Ladebetrieb mit dem Versorgungsnetz
gekoppelt”
fulfilled / erfüllt
not fulfilled / nicht erfüllt
X
n.a.
Remarks / Bemerkungen:
n.a.
Test component not related to
REESS / Geprüftes Bauteil nicht in
Zusammenhang mit REESS
2.2.1
Measurement of radiated broadband electro-
magnetic emissions from electrical/ electronic
subassemblies according to item 7.10 of the
Regulation /
Messungen von gestrahlten breitbandigen el-
ektromagnetischen Störungen aus elektri-
schen/ elektronischen Unterbaugruppen
gemäß Punkt 7.10 der Regelung:
fulfilled / erfüllt
not fulfilled / nicht erfüllt
X
n.a.
2.2.1.1
Measurement procedure /
Messverfahren:
X
n.a.
2.2.1.2
Measurement setup /
Messaufbau:
X
n.a.
2.2.1.3
Test results /
Prüfergebnisse:
X
n.a.
2.2.1.4
Photo documentation of the measurement
setup (if applicable) /
Fotodokumentation des Messaufbaus (sofern
erforderlich):
X
n.a.
2.2.1.5
Remarks / Bemerkungen:
X
n.a.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
9 of / von 17
2.2.2
Measurement of emissions of harmonics on
AC power lines from electrical/ electronic
subassemblies according to item 7.11 of the
regulation / Messungen der Oberwellen auf
AC-Versorgungsleitungen von elektrischen/
elektronischen Unterbaugruppen gemäß
Punkt 7.11 der Regelung
fulfilled / erfüllt
not fulfilled / nicht erfüllt
X
n.a.
2.2.2.1
Measurement results /
Messergebnisse:
X
n.a.
2.2.2.2
Photo documentation of the measurement
setup (if applicable) /
Fotodokumentation des Messaufbaus (sofern
erforderlich):
X
n.a.
2.2.2.3
Remarks / Bemerkungen:
X
n.a.
2.2.3
Measurement of emission of voltages
changes, voltage fluctuation and flicker on
AC power lines from ESAs according to item
7.12 of the Regulation /
Messungen von Spannungsänderungen,
Spannungsschwankungen und Flicker auf
AC-Versorgungsleitungen von elektrischen/
elektronischen Unterbaugruppen gemäß
Punkt 7.12 der Regelung
fulfilled / erfüllt
not fulfilled / nicht erfüllt
X
n.a.
2.2.3.1
Test results /
Prüfergebnisse:
X
n.a.
2.2.3.2
Photo documentation of the measurement
setup (if applicable) /
Fotodokumentation des Messaufbaus (sofern
erforderlich):
X
n.a.
2.2.3.4
Remarks / Bemerkungen:
X
n.a.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
10 of / von 17
2.2.4
Measurement of emission of radiofrequency
conducted disturbances on AC or DC power
lines from ESAs according to item 7.13 of the
Regulation /
Messungen von hochfrequenten Störungen
auf AC- oder DC-Versorgungsleitungen von
elektrischen/ elektronischen Unterbau-
gruppen gemäß Punkt 7.13 der Regelung
fulfilled / erfüllt
not fulfilled / nicht erfüllt
X
n.a.
2.2.4.1
Measurement procedure /
Messverfahren:
X
n.a.
2.2.4.2
Measurement results /
Messergebnisse:
X
n.a.
2.2.4.3
Photo documentation of the measurement
setup (if applicable) /
Fotodokumentation des Messaufbaus (sofern
erforderlich):
X
n.a.
2.2.4.4
Remarks / Bemerkungen:
X
n.a.
E24*10R06/02*4590*00

Technical Report / Technischer Bericht
No. / Nr.: TMXD2301000248DV
Type / Typ: VC900-M8M
Appendix A / Anhang A
Page / Seite
11 of / von 17
2.2.5
Measurement of emission of radiofrequency
conducted disturbances on network or tele-
communication access from ESAs according
to item 7.14 of the Regulation /
Messungen von hochfrequenten Störungen
auf Netzwerk- oder Kommunikationsleitungen
von elektrischen/ elektronischen Unter-
baugruppen gemäß Punkt 7.14 der Regelung
fulfilled / erfüllt
not fulfilled / nicht erfüllt
X
n.a.
2.2.5.1
Measurement procedure /
Messverfahren:
X
n.a.
2.2.5.2
Measurement results /
Messergebnisse:
X
n.a.
2.2.5.3
Photo documentation of the measurement
setup (if applicable) /
Fotodokumentation des Messaufbaus (sofern
erforderlich):
X
n.a.
2.2.5.4
Remarks / Bemerkungen:
X
n.a.
E24*10R06/02*4590*00