DFI IDP121P-MS User manual

User Manual / Installation Guide
IDP121P-MS
ver.A_MP_3-1521_13-13

2User's Manual | IDP0121P-MS
Warning ! It will cause malfunction if the monitor is operating with unspecified power supply
adaptor or incorrect power voltage. Do not expose this unit in the rain or moisture environ-
ment to reduce the risk of fire or electric shock.
· Do not use the monitor near water.
· Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can in-
jure a person and cause serious damage to the appliance. Use only a cart or stand
recommended by the manufacturer or sold with the monitor. If you mount the monitor on a
wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
instructions.
· The monitor should be operated with type of power adaptor indicated on the label.
Normally it is packed with monitor, or using an adaptor approved by the manufacturer.
· Unplug the unit during a lightning storm or when it will not be used for long periods of time.
This will protect the monitor from being damaged due to power surges.
· Never spill liquids on the monitor.
· Do not attempt to service the monitor yourself; opening or removing covers can damage to
the monitor or panel. Please refer all servicing to qualified service personnel.
· For Wall mount adaptor, wall socket shall be installed near the equipment and shall be
easily accessible.
XPRECAUTIONS
XWARNING

3
Table of Contents
Chapter 1 - Introduction ............................................................................................................ 4
Features................................................................................................................................ 4
Unpack the monitor............................................................................................................. 4
Check accessory.................................................................................................................. 4
Chapter 2 - Installation.............................................................................................................. 5
Power Supply & Signal connection .................................................................................... 5
Function Key Control ........................................................................................................... 5
OSD Lock/ Unlock................................................................................................................ 5
Structure of OSD settings ................................................................................................... 5
Chapter 3 - For your safety ....................................................................................................... 6
Chapter 4 - Support timing chart.............................................................................................. 7
Chapter 5 - Projected Capacitive Touch panel ........................................................................ 8
Touch Driver installation: .................................................................................................... 8
Chapter 6 - Mechanical dimension........................................................................................... 9
Chapter 7 - FCC Warning Statement ...................................................................................... 10
FCC Class A Warning......................................................................................................... 10
Chapter 8 - Product General Specification ............................................................................ 11
User's Manual | IDP0121P-MS

4
XFeatures
- This monitor produces clear images with the vivid color at resolutions from VGA up
to XGA and used with graphics adapter of scanning frequency from 30KHz to 82KHz in
horizontal sweep while vertical refresh rate is 55Hz to 76 Hz continuously.
- On Screen Display provide flexibility with simple & user-friendly controls.
- Integrated D-sub and HDMI inputs provide flexible connectivity for high-definition
multimedia devices and gaming consoles
- USB interface Projected Capacitive Touch Panel
- 12.1 inch diagonal screen with native display resolution 800 x 600.
- Dual Video input: VGA, HDMI ( to DVI-D by a HDMI to DVI-D cable)
- Full flat front panel with high quality projected capacitive touch panel.
- Fully Glossy surface throughout monitor’s appearance.
- Rimless front bezel design, spill & dust proof.
- Cable management down routing through the mounting stand.
- Light weight.2,550 g physically.
XUnpack the monitor
- Put the monitor on a clean surface; make sure the box in upright position
- Remove packing materials from inside of box.
XCheck accessory
Please make sure the entire accessory is included:
1.8 meter HDMI cable 1.8 meter Touch USB cable
AC-DC power adaptor : 100Vac~240Vac
Adaptor : 2.1Ø, 12Vdc 18W
( USA/UK/EU Option)
Chapter 1
INTRODUCTION
Chapter 1 - Introduction
User's Manual | IDP0121P-MS

5
Chapter 2
Installation
Chapter 2 - Installation
XPower Supply & Signal connection
Power supply: Use attached Wall-mount Power adaptor to get 12Vdc power.
VGA signal: Use attached 1.8 meter 15pin D-sub VGA cable to connect System PC.
HDMI signal: Apply HDMI signal or use DVI-D to HDMI signal cable for DVI input.
Touch Control: Use attached USB cable to connect system PC.
XFunction Key Control
XOSD Lock/ Unlock
Press “Menu” Key for more than 7 seconds shall lock all control keys’ function.
After keys locked, press “Menu” key again for more than 7 second shall unlock the key
function.
XStructure of OSD settings
User's Manual | IDP0121P-MS

6
Chapter 3
For your safety
Chapter 3 - For your safety
1. When move the monitor, always switch off power and disconnect all cables to avoid
any danger.
2. Please use the power and signal cables correctly when install it.
3. In case of notice any abnormal smell or noise, please stop operation and call the
nearest dealer or service center.
User's Manual | IDP0121P-MS

77
Chapter 4
Support timing chart
Chapter 4 - Support timing chart
User's Manual | IDP0121P-MS

8
Chapter 5
Projected Capacitive Touch panel
Chapter 5 - Projected Capacitive Touch panel
Type 10-Point Project Capacitor Touch Panel
Input Mode Finger or Capacitive Touch screen stylus
Transparency >90%
Touch Control circuitry Build in Touch Panel Module
Control Type USB
Touch Control Driver eGalax Touch Driver or Windows build in touch driver
XTouch Driver installation:
Touch Driver installation:
(1) If you are using Windows XP Embedded OS, please visit EETI website to download driver:
http://www.eeti.com.tw/drivers_Win.html
(2) If your system Windows version is Windows 7 or later, we suggest you do not install this
driver. There is a HID touch digitizer build-in driver in Windows 7, 8, 10.
User's Manual | IDP0121P-MS

9
Chapter 6
Mechanical dimension
Chapter 6 - Mechanical dimension
User's Manual | IDP0121P-MS

10
Chapter 7
FCC Warning Statement
Chapter 7 - FCC Warning Statement
XFCC Class A Warning
This equipment has been tested and found to comply with the limits for a Class A digital de-
vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial en-
vironment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his
own expense.
User's Manual | IDP0121P-MS