DFK HardCabs CAM-AM DEFENDER MAX User manual
INSTALLATION INSTRUCTIONS
CAM-AM
DEFENDER MAX
CAN-AM
DEFENDER MAX
HardCabs 630-324-8585 www.hardcabs.com
2464 Wisconsin Ave.
Downers Grove, IL 60515 info@hardcabs.com
2
SAFETY INSTRUCTIONS
Warning: Failure to heed all safety and operating instructions and
warnings regarding use of this product can result in serious bodily injury.
READ PROPERLY COMPLETE ASSEMBLY INSTRUCTIONS BEFORE
STARTING OF ASSEMBLY
Install all parts indicated in assembly instructions. Failure to fully assemble
product before use could result in personal injury.
Assembly of product requires use of hand or power tools.
If you are not experienced in using these types of tools,
have product dealer do the install for you.
Some parts contain sharp edges, wear protective gloves if necessary.
Always keep your assembly area clean, uncluttered and well lit.
Keep visitors and children a safe distance away from the assembly area. Visitors
should wear the same safety equipment described under.
Never operate your UTV with the cab doors open. Failure to properly latch the
doors before moving the vehicle could result in serious injury.
Dress for safety. DO NOT wear loose clothing, gloves, neckties or jewelry if
using power tools to assemble this product.
Insert all nut covers after you finish installation.
Never drive your UTV with the cab front window in open position.
Failure of unproperly latched/locked front window before driving the vehicle could
result in serious injury.
Please by carefull to not broken the plastic washers, if you tightening screws with
plastic washers use maximal power 3,7 foot-pound force (5 Nm)!!!
CAN-AM
DEFENDER MAX
HardCabs 630-324-8585 www.hardcabs.com
2464 Wisconsin Ave.
Downers Grove, IL 60515 info@hardcabs.com
3
WARNING: For safety purposes, if the DFK Cab doors are removed, it is
mandatory that the OEM manufactured Half Doors or Nets are
REINSTALLED before operating the vehicle.
MAINTENANCE AND CLEANING
To clean polycarbonate surface use soapy water solution or other subtle means.
Dirt and dust wash by gently water stream and swipe only with wet or damp
means in the direction from top to bottom.
The recommended frequency of cleaning of polycarbonate part
is about 1 time per month or according to the actual degree of pollution.
Do not use detergents that could scratch the surface plates.
(abrasives, harsh fabrics, etc.)
Do not use solvents or alkaline detergents or cleaners with ammonia
(ammonium hydroxide).
Do not remove the impurities from the surface of the razor blades or other sharp
items.
Do not clean cabine, when the polycarbonate plates are heated by the sun.
Do not use the squeegee, it could be scratched surface plates.
Do not clean the water current strength greater than 50 bar (WAP)
The manufacturer is not responsible for scratching the surface in case of failure to
comply with the above instructions.
All bolted connections of cab must be by user at regular intervals checked and
tightened.
Please by carefull to not broken the plastic washers, if you tightening screws with
plastic washers use maximal power 3,7 foot-pound force (5 Nm)!!!
CAN-AM
DEFENDER MAX
HardCabs 630-324-8585 www.hardcabs.com
2464 Wisconsin Ave.
Downers Grove, IL 60515 info@hardcabs.com
4
PREPARATION FOR INSTALLATION:
Uninstall all additional systems from the roller cages (work lights, rear mirrors, drink holders etc.)
It is necessary to uninstall rear side tubes (red lines) from the UTV’s from both sides. Save the tubes with
the original screws for later usage.
Losen the fixing screws (red circles) and uninstall the tubes.
CAN-AM
DEFENDER MAX
HardCabs 630-324-8585 www.hardcabs.com
2464 Wisconsin Ave.
Downers Grove, IL 60515 info@hardcabs.com
14
If you install the cab without the doors, fix the rear roof panel with the fixing assemblies. If you have the
complete cab with the doors, fix the rear roof panel with the rear doors frame hinges (page 23).
This manual suits for next models
1
Table of contents
Popular Automobile Accessories manuals by other brands
Cete Automotive
Cete Automotive Air Suspensiom manual
Neo Car Audio
Neo Car Audio ProLink 3V9-BT Installation and operation instructions
Prorack
Prorack K916 Fitting instructions
aci
aci ADARAC Aluminum M Series installation instructions
Bosch
Bosch SCT 815 S5 Original operating instructions
Meyer
Meyer Lot Pro Light Duty Assembly instructions
